| Age | Commit message (Collapse) | Author |
|---|
|
The USB connector should not be placed under the dwc3 node.
Move the USB connector out of the SoC level and use port to describe
the connection to the dwc3 controller.
This fixes the following dt-schema warning:
imx8mp-tqma8mpql-mba8mpxl.dtb: usb@38100000: Unevaluated properties are not allowed ('connector' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The USB connector should not be placed under the dwc3 node.
Move the USB connector out of the SoC level and use port to describe
the connection to the dwc3 controller.
This fixes the following dt-schema warning:
imx8mp-venice-gw72xx-2x.dtb: usb@38100000: Unevaluated properties are not allowed ('connector' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The USB connector should not be placed under the dwc3 node.
Move the USB connector out of the SoC level and use port to describe
the connection to the dwc3 controller.
This fixes the following dt-schema warning:
imx8mp-verdin-wifi-mallow.dtb: usb@32f10100: usb@38100000: Unevaluated properties are not allowed ('connector' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/fsl,imx8mp-dwc3.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The clk_dummy is not part of the usbotg2 block, so move it
to the root node to fix the following dt-schema warning:
imx8dxl-evk.dtb: usb@5b0e0000: Unevaluated properties are not allowed ('clock-dummy' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per nxp,ptn5110.yaml, 'port' should be placed under 'connector'.
Do as requested to fix the following dt-schema warning:
imx8mn-evk.dtb: tcpc@50: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/nxp,ptn5110.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per nxp,ptn5110.yaml, 'port' should be placed under 'connector'.
Do as requested to fix the following dt-schema warning:
imx8mm-evkb.dtb: tcpc@50: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/nxp,ptn5110.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Dimonoff gateway EVK board is based on a Variscite
VAR-SOM-NANO, with a NXP MX8MN nano CPU and also based on a Symphony
mx8mn EVK.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Device tree specification 0.4 defines an optional, but recommended
'chassis-type' property. Add it to TQMa8M* based board files.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SoC is configured to operate in overdrive mode, so it
is safe to include imx8mn-overdrive to run the GPU faster.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8M Nano supports and overdrive mode if the SoC is given
the proper voltage. Add imx8mn-overdrive.dtsi file which can
be included by boards who support the voltage necessary to handle
the faster clocks. This increases the GPU clocks from 400MHz to
600MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SoC runs at a high enough voltage to support overdrive
mode, so include the imx8mm-overdrive.dtsi file to increase
the VPU and GPU clocks to their overdrive speeds.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
For boards who run their SoC at a higher voltage than nominal,
the boards can run several clocks at an overdrive rate for
better performance. Add an optional DTSI file which can be
included by various boards to run in overdrive mode.
This raises the GPU PLL to 1000MHz, and the VPU PLL to
700MHz while moving VPU_G1 and VPU_H1 to the SYS_PLL3_OUT
which runs at 750MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When the GPU nodes were added, the GPU_PLL_OUT was configured
for 1000MHz, but this requires the SoC to run in overdrive mode
which requires an elevated voltage operating point.
Since this may run some boards out of spec, the default clock
should be set to 800MHz for nominal operating mode. Boards
that run at the higher voltage can update their clocks
accordingly.
Fixes: 4523be8e46be ("arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
fsl,micfil.yaml defines the clock-names in the following sequence:
clock-names:
items:
- const: ipg_clk
- const: ipg_clk_app
- const: pll8k
- const: pll11k
- const: clkext3
minItems: 2
imx93.dtsi currently misses the 'pll11k' entry and jump to 'clkext3'.
This leads to the following dt-schema warning:
imx93-11x11-evk.dtb: micfil@44520000: clock-names:3: 'pll11k' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,micfil.yaml#
Fix the warning by describing the clocks up to 'pll8k' as 'clkext3'
is assigned to a dummy clock.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There's no need to do it on every AP.
The C-bit value read on the BSP and also verified there, is used
everywhere from now on.
No functional changes - just a bit faster booting APs.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20231130132601.10317-1-bp@alien8.de
|
|
Add initial board support for the Pixel 6 phone code named Oriole. This
has been tested with a minimal busybox initramfs and boots to a shell.
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20231211162331.435900-16-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Google gs101 SoC is a ARMv8 mobile SoC found in the Pixel 6
(oriole), Pixel 6a (bluejay) and Pixel 6 pro (raven) mobile
phones.
It features:
* 4xA55 Little cluster
* 2xA76 Mid cluster
* 2xX1 Big cluster
This commit adds the basic device tree for gs101 (SoC).
Further platform support will be added over time.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-15-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Deal with a regression in the recently refactored x86 EFI stub code
on older Dell systems by disabling randomization of the physical load
address
- Use the correct load address for relocatable Loongarch kernels
* tag 'efi-urgent-for-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/x86: Avoid physical KASLR on older Dell systems
efi/loongarch: Use load address to calculate kernel entry address
|
|
When intercepts are enabled for MSR_IA32_XSS, the host will swap in/out
the guest-defined values while context-switching to/from guest mode.
However, in the case of SEV-ES, vcpu->arch.guest_state_protected is set,
so the guest-defined value is effectively ignored when switching to
guest mode with the understanding that the VMSA will handle swapping
in/out this register state.
However, SVM is still configured to intercept these accesses for SEV-ES
guests, so the values in the initial MSR_IA32_XSS are effectively
read-only, and a guest will experience undefined behavior if it actually
tries to write to this MSR. Fortunately, only CET/shadowstack makes use
of this register on SEV-ES-capable systems currently, which isn't yet
widely used, but this may become more of an issue in the future.
Additionally, enabling intercepts of MSR_IA32_XSS results in #VC
exceptions in the guest in certain paths that can lead to unexpected #VC
nesting levels. One example is SEV-SNP guests when handling #VC
exceptions for CPUID instructions involving leaf 0xD, subleaf 0x1, since
they will access MSR_IA32_XSS as part of servicing the CPUID #VC, then
generate another #VC when accessing MSR_IA32_XSS, which can lead to
guest crashes if an NMI occurs at that point in time. Running perf on a
guest while it is issuing such a sequence is one example where these can
be problematic.
Address this by disabling intercepts of MSR_IA32_XSS for SEV-ES guests
if the host/guest configuration allows it. If the host/guest
configuration doesn't allow for MSR_IA32_XSS, leave it intercepted so
that it can be caught by the existing checks in
kvm_{set,get}_msr_common() if the guest still attempts to access it.
Fixes: 376c6d285017 ("KVM: SVM: Provide support for SEV-ES vCPU creation/loading")
Cc: Alexey Kardashevskiy <aik@amd.com>
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20231016132819.1002933-4-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The pin control description for the serial console was added, but not
enabled, due to missing pinctrl properties in the serial port device
node.
Fixes: 7a8d590de8132853 ("arm64: dts: renesas: white-hawk-cpu: Add serial port pin control")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8a51516581cd71ecbfa174af9c7cebad1fc83c5b.1702459865.git.geert+renesas@glider.be
|
|
The RZ/G3S Smarc Module has Ethernet PHYs (KSZ9131) connected to each
Ethernet IP. For this, add proper DT descriptions to enable Ethernet
communication through these PHYs.
The interface b/w PHYs and MACs is RGMII. The skew settings were set to
zero as based on phy-mode (rgmii-id) the KSZ9131 driver enables internal
DLL, which adds a 2ns delay b/w clocks (TX/RX) and data signals.
Different pin settings were applied to TXC and TX_CTL compared with the
rest of the RGMII pins to comply with requirements for these pins
imposed by HW manual of RZ/G3S (see chapters "Ether Ch0 Voltage Mode
Control Register (ETH0_POC)", "Ether Ch1 Voltage Mode Control Register
(ETH1_POC)", for power source selection, "Ether MII/RGMII Mode Control
Register (ETH_MODE)" for output-enable and "Input Enable Control
Register (IEN_m)" for input-enable configurations).
Also enable the Ethernet interfaces by selecting SW_CONFIG3 = SW_ON.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-12-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
functionalities
The intention of the SW_SD0_DEV_SEL and SW_SD2_EN macros was to reflect the
state of the SW_CONFIG individual switches available on the RZ/G3S Smarc
Module, and at the same time to have a descriptive name for the switches
themselves. Each individual switch is associated with a signal name,
which might be active-low or not on the board. Using signal names
instead of SW_CONFIG switch names may be confusing for a user who just
playes with switches to select individual functionalities, but also for
an advanced user who looks at the schematics. To avoid even further
confusion, use the switches' names here and instantiate them with an
ON/OFF state. This should be simpler, even though the name of the
switches is not that intuitive. The switches' names documentation
reflects the switches' purposes.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the Ethernet nodes available on RZ/G3S (R9A08G045).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-10-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add IA55 interrupt controller node and set it as interrupt parent for pin
controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-10-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently the detection+enablement of boot cpucaps is separate from the
patching of boot cpucap alternatives, which means there's a period where
cpus_have_cap($CAP) and alternative_has_cap($CAP) may be mismatched.
It would be preferable to manage the boot cpucaps in the same way as the
system cpucaps, both for clarity and to minimize the risk of accidental
usage of code relying upon an alternative which has not yet been
patched.
This patch aligns the handling of boot cpucaps with the handling of
system cpucaps:
* The existing setup_boot_cpu_capabilities() function is moved to be
closer to the setup_system_capabilities() and setup_system_features()
functions so that they're more clearly related and more likely to be
updated together in future.
* The patching of boot cpucap alternatives is moved into
setup_boot_cpu_capabilities(), immediately after boot cpucaps are
detected and enabled.
* A new setup_boot_cpu_features() function is added to mirror
setup_system_features(); this handles initialization of cpucap data
structures and calls setup_boot_cpu_capabilities(). This makes
init_cpu_features() a closer mirror to update_cpu_features(), and
makes smp_prepare_boot_cpu() a closer mirror to smp_cpus_done().
Importantly, while these changes alter the structure of the code, they
retain the existing order of calls to:
init_cpu_features(); // prefix initializing feature regs
init_cpucap_indirect_list();
detect_system_supports_pseudo_nmi();
update_cpu_capabilities(SCOPE_BOOT_CPU | SCOPE_LOCAL_CPU);
enable_cpu_capabilities(SCOPE_BOOT_CPU);
apply_boot_alternatives();
... and hence there should be no functional change as a result of this
patch; this is purely a structural cleanup.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20231212170910.3745497-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Recent changes to remove cpus_have_const_cap() introduced new users of
cpus_have_cap() in the period between detecting system cpucaps and
patching alternatives. It would be preferable to defer these until after
the relevant cpucaps have been patched so that these can use the usual
feature check helper functions, which is clearer and has less risk of
accidental usage of code relying upon an alternative which has not yet
been patched.
This patch reworks the system-wide cpucap detection and patching to
minimize this transient period:
* The detection, enablement, and patching of system cpucaps is moved
into a new setup_system_capabilities() function so that these can be
grouped together more clearly, with no other functions called in the
period between detection and patching. This is called from
setup_system_features() before the subsequent checks that depend on
the cpucaps.
The logging of TTBR0 PAN and cpucaps with a mask is also moved here to
keep these as close as possible to update_cpu_capabilities().
At the same time, comments are corrected and improved to make the
intent clearer.
* As hyp_mode_check() only tests system register values (not hwcaps) and
must be called prior to patching, the call to hyp_mode_check() is
moved before the call to setup_system_features().
* In setup_system_features(), the use of system_uses_ttbr0_pan() is
restored, now that this occurs after alternatives are patched. This is
a partial revert of commit:
53d62e995d9eaed1 ("arm64: Avoid cpus_have_const_cap() for ARM64_HAS_PAN")
* In sve_setup() and sme_setup(), the use of system_supports_sve() and
system_supports_sme() respectively are restored, now that these occur
after alternatives are patched. This is a partial revert of commit:
a76521d160284a1e ("arm64: Avoid cpus_have_const_cap() for ARM64_{SVE,SME,SME2,FA64}")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20231212170910.3745497-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The commit 81186dc16101 ("dt-bindings: zynqmp: add destination mailbox
compatible") make compatible string for child nodes mandatory that's why
add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
node name shouldn't use '_' that's why convert it to '-'.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
fixed clock nodes can't be on the bus because they are missing reg
property. That's why move them to root.
And because it is root it is good to have it as the first node in a file.
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7252203d52af3ca8867764c8514affc4828e530d.1695040866.git.michal.simek@amd.com
|
|
Partitions are described via fixed-partitions that's why there is no need
to have address/size-cells in flash node.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c4447028f914e77b8c28640dc458b8409198ee30.1695040866.git.michal.simek@amd.com
|
|
All zynqmp boards have been already described via mdio node that's why also
convert zc1751. With using mdio node there is an option to add reset
property for the whole mdio bus.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dc228a27579b48f3e768fcb439d118b4a0f0ef5b.1695040866.git.michal.simek@amd.com
|
|
mt25qu512a is not documented in DT binding that's why remove it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a1e975f5785dfb6eb04e8d5905dcaa7467ccd585.1695040866.git.michal.simek@amd.com
|
|
Lower case should be used for register address.
Issue is reported as:
flash@0: partitions: Unevaluated properties are not allowed
('partition@22A0000' was unexpected)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a96ac9a32a363b04958157548f290d480c21590c.1695040866.git.michal.simek@amd.com
|
|
Character '_' not recommended in node name. Use '-' instead.
Pretty much run seds below for node names.
s/zynqmp_ipi/zynqmp-ipi/
s/nvmem_firmware/nvmem-firmware/
s/soc_revision/soc-revision/
s/si5335_/si5335-/
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5137958580c85a35cf6aadd1c33a2f6bcf81a9e5.1695040866.git.michal.simek@amd.com
|
|
DT overlays in tree need to be applied to a base DTB to validate they
apply, to run schema checks on them, and to catch any errors at compile
time. Defining the "-dtbs" variable is not enough as the combined DT must
be added to dtbs-y.
zynqmp-sck-kr-g-revA.dtso and zynqmp-sck-kr-g-revB.dtso don't exist, so drop
them.
Signed-off-by: Rob Herring <robh@kernel.org>
Fixes: 45fe0dc4ea2e ("arm64: xilinx: Use zynqmp prefix for SOM dt overlays")
Link: https://lore.kernel.org/r/20230911214751.2202913-1-robh@kernel.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add pinctrl and MMC controller nodes for the Broadcom wifi controller
on the BeagleV Starlight and StarFive VisionFive V1 boards.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add pinctrl and MMC device tree nodes for the SD-card on the
BeagleV Starlight and StarFive VisionFive V1 boards.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add device tree nodes for the Synopsis MMC controllers on the
StarFive JH7100 SoC.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The StarFive JH7100 SoC has non-coherent device DMAs, but most drivers
expect to be able to allocate coherent memory for DMA descriptors and
such. However on the JH7100 DDR memory appears twice in the physical
memory map, once cached and once uncached:
0x00_8000_0000 - 0x08_7fff_ffff : Off chip DDR memory, cached
0x10_0000_0000 - 0x17_ffff_ffff : Off chip DDR memory, uncached
To use this uncached region we create a global DMA memory pool there and
reserve the corresponding area in the cached region.
However the uncached region is fully above the 32bit address limit, so add
a dma-ranges map so the DMA address used for peripherals is still in the
regular cached region below the limit.
Link: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Data%20Sheet%20V01.01.04-EN%20(4-21-2021).pdf
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The StarFive JH7100 SoC also features the SiFive L2 cache controller,
so add the device tree nodes for it.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The StarFive JH7100 SoC has non-coherent device DMAs, so mark the
soc bus as such.
Link: https://github.com/starfive-tech/JH7100_Docs/blob/main/JH7100%20Cache%20Coherence%20V1.0.pdf
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.
Fix this by grouping the tuples of "interrupts-extended" properties
using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This not really an errata, but since the JH7100 was made before
the standard Zicbom extension it needs the DMA_GLOBAL_POOL and
RISCV_NONSTANDARD_CACHE_OPS enabled to work correctly.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add the Series AXE GPU node to the AM62 device tree.
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Sarah Walker <sarah.walker@imgtec.com>
Signed-off-by: Donald Robson <donald.robson@imgtec.com>
Acked-by: Darren Etheridge <detheridge@ti.com>
Link: https://lore.kernel.org/r/7088cc032374ae517191b1dadf5bb5f0440eac81.1701773390.git.donald.robson@imgtec.com
Signed-off-by: Nishanth Menon <nm@ti.com>
|
