| Age | Commit message (Collapse) | Author |
|---|
|
The debugging code for kmap_local() doubles the number of per-CPU fixmap
slots allocated for kmap_local(), in order to use half of them as guard
regions. This causes the fixmap region to grow downwards beyond the start
of its reserved window if the supported number of CPUs is large, and collide
with the newly added virtual DT mapping right below it, which is obviously
not good.
One manifestation of this is EFI boot on a kernel built with NR_CPUS=32
and CONFIG_DEBUG_KMAP_LOCAL=y, which may pass the FDT in highmem, resulting
in block entries below the fixmap region that the fixmap code misidentifies
as fixmap table entries, and subsequently tries to dereference using a
phys-to-virt translation that is only valid for lowmem. This results in a
cryptic splat such as the one below.
ftrace: allocating 45548 entries in 89 pages
8<--- cut here ---
Unable to handle kernel paging request at virtual address fc6006f0
pgd = (ptrval)
[fc6006f0] *pgd=80000040207003, *pmd=00000000
Internal error: Oops: a06 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.11.0+ #382
Hardware name: Generic DT based system
PC is at cpu_ca15_set_pte_ext+0x24/0x30
LR is at __set_fixmap+0xe4/0x118
pc : [<c041ac9c>] lr : [<c04189d8>] psr: 400000d3
sp : c1601ed8 ip : 00400000 fp : 00800000
r10: 0000071f r9 : 00421000 r8 : 00c00000
r7 : 00c00000 r6 : 0000071f r5 : ffade000 r4 : 4040171f
r3 : 00c00000 r2 : 4040171f r1 : c041ac78 r0 : fc6006f0
Flags: nZcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
Control: 30c5387d Table: 40203000 DAC: 00000001
Process swapper (pid: 0, stack limit = 0x(ptrval))
So let's limit CONFIG_NR_CPUS to 16 when CONFIG_DEBUG_KMAP_LOCAL=y. Also,
fix the BUILD_BUG_ON() check that was supposed to catch this, by checking
whether the region grows below the start address rather than above the end
address.
Fixes: 2a15ba82fa6ca3f3 ("ARM: highmem: Switch to generic kmap atomic")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
On NVIDIA Carmel cores, CNP behaves differently than it does on standard
ARM cores. On Carmel, if two cores have CNP enabled and share an L2 TLB
entry created by core0 for a specific ASID, a non-shareable TLBI from
core1 may still see the shared entry. On standard ARM cores, that TLBI
will invalidate the shared entry as well.
This causes issues with patchsets that attempt to do local TLBIs based
on cpumasks instead of broadcast TLBIs. Avoid these issues by disabling
CNP support for NVIDIA Carmel cores.
Signed-off-by: Rich Wiley <rwiley@nvidia.com>
Link: https://lore.kernel.org/r/20210324002809.30271-1-rwiley@nvidia.com
[will: Fix pre-existing whitespace issue]
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Fix GCC warnings reported when building with "-Wmissing-prototypes":
arch/arm64/kernel/process.c:261:6: warning: no previous prototype for '__show_regs' [-Wmissing-prototypes]
261 | void __show_regs(struct pt_regs *regs)
| ^~~~~~~~~~~
arch/arm64/kernel/process.c:307:6: warning: no previous prototype for '__show_regs_alloc_free' [-Wmissing-prototypes]
307 | void __show_regs_alloc_free(struct pt_regs *regs)
| ^~~~~~~~~~~~~~~~~~~~~~
arch/arm64/kernel/process.c:365:5: warning: no previous prototype for 'arch_dup_task_struct' [-Wmissing-prototypes]
365 | int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src)
| ^~~~~~~~~~~~~~~~~~~~
arch/arm64/kernel/process.c:546:41: warning: no previous prototype for '__switch_to' [-Wmissing-prototypes]
546 | __notrace_funcgraph struct task_struct *__switch_to(struct task_struct *prev,
| ^~~~~~~~~~~
arch/arm64/kernel/process.c:710:25: warning: no previous prototype for 'arm64_preempt_schedule_irq' [-Wmissing-prototypes]
710 | asmlinkage void __sched arm64_preempt_schedule_irq(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/lkml/202103192250.AennsfXM-lkp@intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Link: https://lore.kernel.org/r/1616568899-986-1-git-send-email-maninder1.s@samsung.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
kmap() is inefficient and is being replaced by kmap_local_page(), if
possible. There is no readily apparent reason why initp_page needs to be
allocated and kmap'ed() except that 'sigstruct' needs to be page-aligned
and 'token' 512 byte-aligned.
Rather than change it to kmap_local_page(), use kmalloc() instead
because kmalloc() can give this alignment when allocating PAGE_SIZE
bytes.
Remove the alloc_page()/kmap() and replace with kmalloc(PAGE_SIZE, ...)
to get a page aligned kernel address.
In addition, add a comment to document the alignment requirements so that
others don't attempt to 'fix' this again.
[ bp: Massage commit message. ]
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210324182246.2484875-1-ira.weiny@intel.com
|
|
Pull networking fixes from David Miller:
"Various fixes, all over:
1) Fix overflow in ptp_qoriq_adjfine(), from Yangbo Lu.
2) Always store the rx queue mapping in veth, from Maciej
Fijalkowski.
3) Don't allow vmlinux btf in map_create, from Alexei Starovoitov.
4) Fix memory leak in octeontx2-af from Colin Ian King.
5) Use kvalloc in bpf x86 JIT for storing jit'd addresses, from
Yonghong Song.
6) Fix tx ptp stats in mlx5, from Aya Levin.
7) Check correct ip version in tun decap, fropm Roi Dayan.
8) Fix rate calculation in mlx5 E-Switch code, from arav Pandit.
9) Work item memork leak in mlx5, from Shay Drory.
10) Fix ip6ip6 tunnel crash with bpf, from Daniel Borkmann.
11) Lack of preemptrion awareness in macvlan, from Eric Dumazet.
12) Fix data race in pxa168_eth, from Pavel Andrianov.
13) Range validate stab in red_check_params(), from Eric Dumazet.
14) Inherit vlan filtering setting properly in b53 driver, from
Florian Fainelli.
15) Fix rtnl locking in igc driver, from Sasha Neftin.
16) Pause handling fixes in igc driver, from Muhammad Husaini
Zulkifli.
17) Missing rtnl locking in e1000_reset_task, from Vitaly Lifshits.
18) Use after free in qlcnic, from Lv Yunlong.
19) fix crash in fritzpci mISDN, from Tong Zhang.
20) Premature rx buffer reuse in igb, from Li RongQing.
21) Missing termination of ip[a driver message handler arrays, from
Alex Elder.
22) Fix race between "x25_close" and "x25_xmit"/"x25_rx" in hdlc_x25
driver, from Xie He.
23) Use after free in c_can_pci_remove(), from Tong Zhang.
24) Uninitialized variable use in nl80211, from Jarod Wilson.
25) Off by one size calc in bpf verifier, from Piotr Krysiuk.
26) Use delayed work instead of deferrable for flowtable GC, from
Yinjun Zhang.
27) Fix infinite loop in NPC unmap of octeontx2 driver, from
Hariprasad Kelam.
28) Fix being unable to change MTU of dwmac-sun8i devices due to lack
of fifo sizes, from Corentin Labbe.
29) DMA use after free in r8169 with WoL, fom Heiner Kallweit.
30) Mismatched prototypes in isdn-capi, from Arnd Bergmann.
31) Fix psample UAPI breakage, from Ido Schimmel"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (171 commits)
psample: Fix user API breakage
math: Export mul_u64_u64_div_u64
ch_ktls: fix enum-conversion warning
octeontx2-af: Fix memory leak of object buf
ptp_qoriq: fix overflow in ptp_qoriq_adjfine() u64 calcalation
net: bridge: don't notify switchdev for local FDB addresses
net/sched: act_ct: clear post_ct if doing ct_clear
net: dsa: don't assign an error value to tag_ops
isdn: capi: fix mismatched prototypes
net/mlx5: SF, do not use ecpu bit for vhca state processing
net/mlx5e: Fix division by 0 in mlx5e_select_queue
net/mlx5e: Fix error path for ethtool set-priv-flag
net/mlx5e: Offload tuple rewrite for non-CT flows
net/mlx5e: Allow to match on MPLS parameters only for MPLS over UDP
net/mlx5: Add back multicast stats for uplink representor
net: ipconfig: ic_dev can be NULL in ic_close_devs
MAINTAINERS: Combine "QLOGIC QLGE 10Gb ETHERNET DRIVER" sections into one
docs: networking: Fix a typo
r8169: fix DMA being used after buffer free if WoL is enabled
net: ipa: fix init header command validation
...
|
|
This partially reverts commit 882213990d32 ("xen: fix p2m size in dom0
for disabled memory hotplug case")
There's no need to special case XEN_UNPOPULATED_ALLOC anymore in order
to correctly size the p2m. The generic memory hotplug option has
already been tied together with the Xen hotplug limit, so enabling
memory hotplug should already trigger a properly sized p2m on Xen PV.
Note that XEN_UNPOPULATED_ALLOC depends on ZONE_DEVICE which pulls in
MEMORY_HOTPLUG.
Leave the check added to __set_phys_to_machine and the adjusted
comment about EXTRA_MEM_RATIO.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210324122424.58685-3-roger.pau@citrix.com
[boris: fixed formatting issues]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
The Xen memory hotplug limit should depend on the memory hotplug
generic option, rather than the Xen balloon configuration. It's
possible to have a kernel with generic memory hotplug enabled, but
without Xen balloon enabled, at which point memory hotplug won't work
correctly due to the size limitation of the p2m.
Rename the option to XEN_MEMORY_HOTPLUG_LIMIT since it's no longer
tied to ballooning.
Fixes: 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory")
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210324122424.58685-2-roger.pau@citrix.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
On contemporary platforms we don't use FIQ, and treat any stray FIQ as a
fatal event. However, some platforms have an interrupt controller wired
to FIQ, and need to handle FIQ as part of regular operation.
So that we can support both cases dynamically, this patch updates the
FIQ exception handling code to operate the same way as the IRQ handling
code, with its own handle_arch_fiq handler. Where a root FIQ handler is
not registered, an unexpected FIQ exception will trigger the default FIQ
handler, which will panic() as today. Where a root FIQ handler is
registered, handling of the FIQ is deferred to that handler.
As el0_fiq_invalid_compat is supplanted by el0_fiq, the former is
removed. For !CONFIG_COMPAT builds we never expect to take an exception
from AArch32 EL0, so we keep the common el0_fiq_invalid handler.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-7-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Apple SoCs (A11 and newer) have some interrupt sources hardwired to the
FIQ line. We implement support for this by simply treating IRQs and FIQs
the same way in the interrupt vectors.
To support these systems, the FIQ mask bit needs to be kept in sync with
the IRQ mask bit, so both kinds of exceptions are masked together. No
other platforms should be delivering FIQ exceptions right now, and we
already unmask FIQ in normal process context, so this should not have an
effect on other systems - if spurious FIQs were arriving, they would
already panic the kernel.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-6-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In subsequent patches we'll allow an FIQ handler to be registered, and
FIQ exceptions will need to be triaged very similarly to IRQ exceptions.
So that we can reuse the existing logic, this patch factors the IRQ
triage logic out into macros that can be reused for FIQ.
The macros are named to follow the elX_foo_handler scheme used by the C
exception handlers. For consistency with other top-level exception
handlers, the kernel_entry/kernel_exit logic is not moved into the
macros. As FIQ will use a different C handler, this handler name is
provided as an argument to the macros.
There should be no functional change as a result of this patch.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[Mark: rework macros, commit message, rebase before DAIF rework]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-5-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
If we accidentally unmask IRQs before we've registered a root IRQ
handler, handle_arch_irq will be NULL, and the IRQ exception handler
will branch to a bogus address.
To make this easier to debug, this patch initialises handle_arch_irq to
a default handler which will panic(), making such problems easier to
debug. When we add support for FIQ handlers, we can follow the same
approach.
When we add support for a root FIQ handler, it's possible to have root
IRQ handler without an root FIQ handler, and in theory the inverse is
also possible. To permit this, and to keep the IRQ/FIQ registration
logic similar, this patch removes the panic in the absence of a root IRQ
controller. Instead, set_handle_irq() logs when a handler is registered,
which is sufficient for debug purposes.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In subsequent patches we want to allow irqchip drivers to register as
FIQ handlers, with a set_handle_fiq() function. To keep the IRQ/FIQ
paths similar, we want arm64 to provide both set_handle_irq() and
set_handle_fiq(), rather than using GENERIC_IRQ_MULTI_HANDLER for the
former.
This patch adds an arm64-specific implementation of set_handle_irq().
There should be no functional change as a result of this patch.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[Mark: use a single handler pointer]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In order to detect whether a GICv3 CPU interface is MMIO capable,
we switch ICC_SRE_EL1.SRE to 0 and check whether it sticks.
However, this is only possible if *ALL* of the HCR_EL2 interrupt
overrides are set, and the CPU is perfectly allowed to ignore
the write to ICC_SRE_EL1 otherwise. This leads KVM to pretend
that a whole bunch of ARMv8.0 CPUs aren't MMIO-capable, and
breaks VMs that should work correctly otherwise.
Fix this by setting IMO/FMO/IMO before touching ICC_SRE_EL1,
and clear them afterwards. This allows us to reliably detect
the CPU interface capabilities.
Tested-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Fixes: 9739f6ef053f ("KVM: arm64: Workaround firmware wrongly advertising GICv2-on-v3 compatibility")
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Disable guest access to the Trace Filter control registers.
We do not advertise the Trace filter feature to the guest
(ID_AA64DFR0_EL1: TRACE_FILT is cleared) already, but the guest
can still access the TRFCR_EL1 unless we trap it.
This will also make sure that the guest cannot fiddle with
the filtering controls set by a nvhe host.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-3-suzuki.poulose@arm.com
|
|
Currently we advertise the ID_AA6DFR0_EL1.TRACEVER for the guest,
when the trace register accesses are trapped (CPTR_EL2.TTA == 1).
So, the guest will get an undefined instruction, if trusts the
ID registers and access one of the trace registers.
Lets be nice to the guest and hide the feature to avoid
unexpected behavior.
Even though this can be done at KVM sysreg emulation layer,
we do this by removing the TRACEVER from the sanitised feature
register field. This is fine as long as the ETM drivers
can handle the individual trace units separately, even
when there are differences among the CPUs.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-2-suzuki.poulose@arm.com
|
|
Commit 9c698bff66ab ("ARM: ensure the signal page contains defined contents")
poisoned the unused portions of the signal page for 32-bit Arm.
Implement the same poisoning for the compat signal page on arm64 rather
than using __GFP_ZERO.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-6-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We can avoid the expensive ISB instruction after reading the counter in
the vDSO gettime functions by creating a fake address hazard against a
dummy stack read, just like we do inside the kernel.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-5-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
For compatability with 32-bit Arm, allow the compat signal page to be
remapped via mremap().
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-4-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
flush_dcache_page() ensures that the 'PG_dcache_clean' flag for its
'page' argument is clear so that cache maintenance will be performed
if the page is mapped into userspace with execute permissions.
Newly allocated pages have this flag clear, so there is no need to call
flush_dcache_page() for the compat vdso or signal pages. Remove the
redundant calls.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-3-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
There's no need to allocate the compat vDSO and signal pages using
GFP_ATOMIC allocations, so use GFP_KERNEL instead.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-2-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Linux has support for free page reporting now (36e66c554b5c) for
virtualized environment. On Hyper-V when virtually backed VMs are
configured, Hyper-V will advertise cold memory discard capability,
when supported. This patch adds the support to hook into the free
page reporting infrastructure and leverage the Hyper-V cold memory
discard hint hypercall to report/free these pages back to the host.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Tested-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/SN4PR2101MB0880121FA4E2FEC67F35C1DCC0649@SN4PR2101MB0880.namprd21.prod.outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
arch/x86/hyperv/hv_apic.c:58:15: warning: variable ‘hi’ set but not used [-Wunused-but-set-variable]
Compiled with CONFIG_HYPERV enabled:
make allmodconfig ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-
make W=1 arch/x86/hyperv/hv_apic.o ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-
HV_X64_MSR_EOI occupies bit 31:0 and HV_X64_MSR_TPR occupies bit 7:0,
which means the higher 32 bits are not really used. Cast the variable hi
to void to silence this warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xu Yihang <xuyihang@huawei.com>
Link: https://lore.kernel.org/r/20210323025013.191533-1-xuyihang@huawei.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
arch/x86/hyperv/hv_spinlock.c:28:16: warning: variable ‘msr_val’ set but not used [-Wunused-but-set-variable]
unsigned long msr_val;
As Hypervisor Top-Level Functional Specification states in chapter 7.5
Virtual Processor Idle Sleep State, "A partition which possesses the
AccessGuestIdleMsr privilege (refer to section 4.2.2) may trigger entry
into the virtual processor idle sleep state through a read to the
hypervisor-defined MSR HV_X64_MSR_GUEST_IDLE".
That means only a read of the MSR is necessary. The returned value
msr_val is not used. Cast it to void to silence this warning.
Reference:
https://docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xu Yihang <xuyihang@huawei.com>
Link: https://lore.kernel.org/r/20210323024302.174434-1-xuyihang@huawei.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Fix warning: no previous prototype for 'omap_init_time_of'.
Fixes: e69b4e1a7577 ("ARM: OMAP2+: Add omap_init_time_of()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add an injection file in order to specify the IPID too when injecting
an error. One use case example is using the machinery to decode MCEs
collected from other machines.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210314201806.12798-1-bp@alien8.de
|
|
There are two variants of the Jetson Xavier NX platform; one has an
eMMC and one as a micro SD-card slot. The SDHCI controller used by
each variant is different, however, the current device-tree for both
Xavier NX boards have the same SDHCI controller defined as 'mmc0' in
the device-tree alias node. Fix this by correcting the 'mmc0' alias
for the SD-card variant.
Fixes: 3f9efbbe57bc ("arm64: tegra: Add support for Jetson Xavier NX")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 5d25c476f252 ("Revert "arm64: tegra: Disable the ACONNECT for
Jetson TX2"") re-enabled the Tegra ADMA and ACONNECT drivers to support
audio on Jetson TX2. However, this revert was dependent upon commit
e590474768f1 ("driver core: Set fw_devlink=on by default") and without
this commit, enabling the ACONNECT is causing resume from system suspend
to fail on Jetson TX2. Resume fails because the ACONNECT driver is being
resumed before the BPMP driver, and the ACONNECT driver is attempting to
power on a power-domain that is provided by the BPMP.
Commit e590474768f1 ("driver core: Set fw_devlink=on by default") has
since been temporarily reverted while some issues are being
investigated. This is causing resume from system suspend on Jetson TX2
to fail again. Rather than disable the ACONNECT driver again, fix this
by setting fw_devlink is set to 'on' for Jetson TX2 in the bootargs
specified in device-tree.
Fixes: 5d25c476f252 ("Revert arm64: tegra: Disable the ACONNECT for Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ACONNECT device tree node has a unit-address on all other SoC
generations and there's really no reason not to have it on Tegra186.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently, the first several pages are reserved both to avoid leaking
their contents on systems with L1TF and to avoid corrupting BIOS memory.
Merge the two memory reservations.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210302100406.22059-3-rppt@kernel.org
|
|
The early reservations of memory areas used by the firmware, bootloader,
kernel text and data are spread over setup_arch(). Moreover, some of them
happen *after* memblock allocations, e.g trim_platform_memory_ranges() and
trim_low_memory_range() are called after reserve_real_mode() that allocates
memory.
There was no corruption of these memory regions because memblock always
allocates memory either from the end of memory (in top-down mode) or above
the kernel image (in bottom-up mode). However, the bottom up mode is going
to be updated to span the entire memory [1] to avoid limitations caused by
KASLR.
Consolidate early memory reservations in a dedicated function to improve
robustness against future changes. Having the early reservations in one
place also makes it clearer what memory must be reserved before memblock
allocations are allowed.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Baoquan He <bhe@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: David Hildenbrand <david@redhat.com>
Link: [1] https://lore.kernel.org/lkml/20201217201214.3414100-2-guro@fb.com
Link: https://lkml.kernel.org/r/20210302100406.22059-2-rppt@kernel.org
|
|
The new Ubuntu GCC packages turn on -fcf-protection globally,
which causes a build failure in the x86 realmode code:
cc1: error: ‘-fcf-protection’ is not compatible with this target
Turn it off explicitly on compilers that understand this option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210323124846.1584944-1-arnd@kernel.org
|
|
The pfn variable contains the page frame number as returned by the
pXX_pfn() functions, shifted to the right by PAGE_SHIFT to remove the
page bits. After page protection computations are done to it, it gets
shifted back to the physical address using page_level_shift().
That is wrong, of course, because that function determines the shift
length based on the level of the page in the page table but in all the
cases, it was shifted by PAGE_SHIFT before.
Therefore, shift it back using PAGE_SHIFT to get the correct physical
address.
[ bp: Rewrite commit message. ]
Fixes: dfaaec9033b8 ("x86: Add support for changing memory encryption attribute in early boot")
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/81abbae1657053eccc535c16151f63cd049dcb97.1616098294.git.isaku.yamahata@intel.com
|
|
Add EXTI lines to the following UART nodes which are used for
wakeup from CStop.
- EXTI line 26 to USART1
- EXTI line 27 to USART2
- EXTI line 28 to USART3
- EXTI line 29 to USART6
- EXTI line 30 to UART4
- EXTI line 31 to UART5
- EXTI line 32 to UART7
- EXTI line 33 to UART8
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210319184253.5841-6-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
GCC gets confused by the comparison of a pointer to an integer literal,
with the assumption that this is an offset from a NULL pointer and that
dereferencing it is invalid:
In file included from arch/x86/boot/compressed/misc.c:18:
In function ‘parse_elf’,
inlined from ‘extract_kernel’ at arch/x86/boot/compressed/misc.c:442:2:
arch/x86/boot/compressed/../string.h:15:23: error: ‘__builtin_memcpy’ reading 64 bytes from a region of size 0 [-Werror=stringop-overread]
15 | #define memcpy(d,s,l) __builtin_memcpy(d,s,l)
| ^~~~~~~~~~~~~~~~~~~~~~~
arch/x86/boot/compressed/misc.c:283:9: note: in expansion of macro ‘memcpy’
283 | memcpy(&ehdr, output, sizeof(ehdr));
| ^~~~~~
I could not find any good workaround for this, but as this is only
a warning for a failure during early boot, removing the line entirely
works around the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Sebor <msebor@gmail.com>
Link: https://lore.kernel.org/r/20210322160253.4032422-2-arnd@kernel.org
|
|
gcc-11 warns about using string operations on pointers that are
defined at compile time as offsets from a NULL pointer. Unfortunately
that also happens on the result of fix_to_virt(), which is a
compile-time constant for a constant input:
arch/x86/kernel/tboot.c: In function 'tboot_probe':
arch/x86/kernel/tboot.c:70:13: error: '__builtin_memcmp_eq' specified bound 16 exceeds source size 0 [-Werror=stringop-overread]
70 | if (memcmp(&tboot_uuid, &tboot->uuid, sizeof(tboot->uuid))) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
I hope this can get addressed in gcc-11 before the release.
As a workaround, split up the tboot_probe() function in two halves
to separate the pointer generation from the usage. This is a bit
ugly, and hopefully gcc understands that the code is actually correct
before it learns to peek into the noinline function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578
Link: https://lore.kernel.org/r/20210322160253.4032422-3-arnd@kernel.org
|
|
Building with 'make W=1', gcc points out that casting between
incompatible function types can be dangerous:
arch/x86/math-emu/fpu_trig.c:1638:60: error: cast between incompatible function types from ‘int (*)(FPU_REG *, u_char)’ {aka ‘int (*)(struct fpu__reg *, unsigned char)’} to ‘void (*)(FPU_REG *, u_char)’ {aka ‘void (*)(struct fpu__reg *, unsigned char)’} [-Werror=cast-function-type]
1638 | fprem, fyl2xp1, fsqrt_, fsincos, frndint_, fscale, (FUNC_ST0) fsin, fcos
| ^
This one seems harmless, but it is easy enough to work around it by
adding an intermediate function that adjusts the return type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210322214824.974323-1-arnd@kernel.org
|
|
The pseries join/suspend sequence in its current form was written with
the assumption that it was the only user of H_PROD and that it needn't
handle spurious successful returns from H_JOIN. That's wrong;
powerpc's paravirt spinlock code uses H_PROD, and CPUs entering
do_join() can be woken prematurely from H_JOIN with a status of
H_SUCCESS as a result. This causes all CPUs to exit the sequence
early, preventing suspend from occurring at all.
Add a 'done' boolean flag to the pseries_suspend_info struct, and have
the waking thread set it before waking the other threads. Threads
which receive H_SUCCESS from H_JOIN retry if the 'done' flag is still
unset.
Fixes: 9327dc0aeef3 ("powerpc/pseries/mobility: use stop_machine for join/suspend")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315080045.460331-3-nathanl@linux.ibm.com
|
|
The atomic_t counter is the only shared state for the join/suspend
sequence so far, but that will change. Contain it in a
struct (pseries_suspend_info), and document its intended use. No
functional change.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315080045.460331-2-nathanl@linux.ibm.com
|
|
Currently, the late microcode loading mechanism checks whether any CPUs
are offlined, and, in such a case, aborts the load attempt.
However, this must be done before the kernel caches new microcode from
the filesystem. Otherwise, when offlined CPUs are onlined later, those
cores are going to be updated through the CPU hotplug notifier callback
with the new microcode, while CPUs previously onine will continue to run
with the older microcode.
For example:
Turn off one core (2 threads):
echo 0 > /sys/devices/system/cpu/cpu3/online
echo 0 > /sys/devices/system/cpu/cpu1/online
Install the ucode fails because a primary SMT thread is offline:
cp intel-ucode/06-8e-09 /lib/firmware/intel-ucode/
echo 1 > /sys/devices/system/cpu/microcode/reload
bash: echo: write error: Invalid argument
Turn the core back on
echo 1 > /sys/devices/system/cpu/cpu3/online
echo 1 > /sys/devices/system/cpu/cpu1/online
cat /proc/cpuinfo |grep microcode
microcode : 0x30
microcode : 0xde
microcode : 0x30
microcode : 0xde
The rationale for why the update is aborted when at least one primary
thread is offline is because even if that thread is soft-offlined
and idle, it will still have to participate in broadcasted MCE's
synchronization dance or enter SMM, and in both examples it will execute
instructions so it better have the same microcode revision as the other
cores.
[ bp: Heavily edit and extend commit message with the reasoning behind all
this. ]
Fixes: 30ec26da9967 ("x86/microcode: Do not upload microcode if CPUs are offline")
Signed-off-by: Otavio Pontes <otavio.pontes@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lkml.kernel.org/r/20210319165515.9240-2-otavio.pontes@intel.com
|
|
gcc-11 warns about mismatched prototypes here:
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
GCC is right here - fix up the types.
[ mingo: Twiddled the changelog. ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210322164541.912261-1-arnd@kernel.org
|
|
Signed-off-by: dean.yang_cp <yangdianqing@yulong.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
The copy_to_user() function returns the number of bytes remaining to be
copied, but we want to return -EFAULT if the copy doesn't complete.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Memory hotplug may fail on systems with CONFIG_RANDOMIZE_BASE because the
linear map range is not checked correctly.
The start physical address that linear map covers can be actually at the
end of the range because of randomization. Check that and if so reduce it
to 0.
This can be verified on QEMU with setting kaslr-seed to ~0ul:
memstart_offset_seed = 0xffff
START: __pa(_PAGE_OFFSET(vabits_actual)) = ffff9000c0000000
END: __pa(PAGE_END - 1) = 1000bfffffff
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Fixes: 58284a901b42 ("arm64/mm: Validate hotplug range before creating linear mapping")
Tested-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20210216150351.129018-2-pasha.tatashin@soleen.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The ppos points to a position in the old kernel memory (and in case of
arm64 in the crash kernel since elfcorehdr is passed as a segment). The
function should update the ppos by the amount that was read. This bug is
not exposed by accident, but other platforms update this value properly.
So, fix it in ARM64 version of elfcorehdr_read() as well.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Fixes: e62aaeac426a ("arm64: kdump: provide /proc/vmcore file")
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20210319205054.743368-1-pasha.tatashin@soleen.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
s/acurate/accurate/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210319222848.29928-1-unixbhaskar@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We recently converted arm64 to use arch_stack_walk() in commit:
5fc57df2f6fd ("arm64: stacktrace: Convert to ARCH_STACKWALK")
The core stacktrace code expects that (when tracing the current task)
arch_stack_walk() starts a trace at its caller, and does not include
itself in the trace. However, arm64's arch_stack_walk() includes itself,
and so traces include one more entry than callers expect. The core
stacktrace code which calls arch_stack_walk() tries to skip a number of
entries to prevent itself appearing in a trace, and the additional entry
prevents skipping one of the core stacktrace functions, leaving this in
the trace unexpectedly.
We can fix this by having arm64's arch_stack_walk() begin the trace with
its caller. The first value returned by the trace will be
__builtin_return_address(0), i.e. the caller of arch_stack_walk(). The
first frame record to be unwound will be __builtin_frame_address(1),
i.e. the caller's frame record. To prevent surprises, arch_stack_walk()
is also marked noinline.
While __builtin_frame_address(1) is not safe in portable code, local GCC
developers have confirmed that it is safe on arm64. To find the caller's
frame record, the builtin can safely dereference the current function's
frame record or (in theory) could stash the original FP into another GPR
at function entry time, neither of which are problematic.
Prior to this patch, the tracing code would unexpectedly show up in
traces of the current task, e.g.
| # cat /proc/self/stack
| [<0>] stack_trace_save_tsk+0x98/0x100
| [<0>] proc_pid_stack+0xb4/0x130
| [<0>] proc_single_show+0x60/0x110
| [<0>] seq_read_iter+0x230/0x4d0
| [<0>] seq_read+0xdc/0x130
| [<0>] vfs_read+0xac/0x1e0
| [<0>] ksys_read+0x6c/0xfc
| [<0>] __arm64_sys_read+0x20/0x30
| [<0>] el0_svc_common.constprop.0+0x60/0x120
| [<0>] do_el0_svc+0x24/0x90
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0_sync_handler+0x1a4/0x1b0
| [<0>] el0_sync+0x170/0x180
After this patch, the tracing code will not show up in such traces:
| # cat /proc/self/stack
| [<0>] proc_pid_stack+0xb4/0x130
| [<0>] proc_single_show+0x60/0x110
| [<0>] seq_read_iter+0x230/0x4d0
| [<0>] seq_read+0xdc/0x130
| [<0>] vfs_read+0xac/0x1e0
| [<0>] ksys_read+0x6c/0xfc
| [<0>] __arm64_sys_read+0x20/0x30
| [<0>] el0_svc_common.constprop.0+0x60/0x120
| [<0>] do_el0_svc+0x24/0x90
| [<0>] el0_svc+0x2c/0x54
| [<0>] el0_sync_handler+0x1a4/0x1b0
| [<0>] el0_sync+0x170/0x180
Erring on the side of caution, I've given this a spin with a bunch of
toolchains, verifying the output of /proc/self/stack and checking that
the assembly looked sound. For GCC (where we require version 5.1.0 or
later) I tested with the kernel.org crosstool binares for versions
5.5.0, 6.4.0, 6.5.0, 7.3.0, 7.5.0, 8.1.0, 8.3.0, 8.4.0, 9.2.0, and
10.1.0. For clang (where we require version 10.0.1 or later) I tested
with the llvm.org binary releases of 11.0.0, and 11.0.1.
Fixes: 5fc57df2f6fd ("arm64: stacktrace: Convert to ARCH_STACKWALK")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Jun <chenjun102@huawei.com>
Cc: Marco Elver <elver@google.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org> # 5.10.x
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210319184106.5688-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Fix another ~42 single-word typos in arch/x86/ code comments,
missed a few in the first pass, in particular in .S files.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-kernel@vger.kernel.org
|
|
We've accumulated a few unusual Unicode characters in arch/x86/
over the years, substitute them with their proper ASCII equivalents.
A few of them were a whitespace equivalent: ' ' - the use was harmless.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
|
|
Conflicts:
arch/x86/kernel/kprobes/ftrace.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
