| Age | Commit message (Collapse) | Author |
|---|
|
These are i.MX6S/DL based SBCs embedded in various Y Soft products.
All share the same board design but have slightly different HW
configuration.
Ursa
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 1x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
Draco
- i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
- parallel WVGA 7" LCD with touch panel
- 2x Eth (QCA8334 switch)
- USB OTG
- USB host (micro-B)
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
Hydra
- i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
- I2C OLED display, capacitive matrix keys
- 2x Eth (QCA8334 switch)
- USB OTG
- RGB LED (I2C LP5562)
- 3.5mm audio jack + codec (LM49350)
- HDMI
- miniPCIe slot
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX7ULP SoC revision info is inside the SIM mode's JTAG_ID
register, add sim node to support SoC revision check.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6ULL has errata ERR010450, there is I/O timing limitation,
for SDR mode, SD card clock can't exceed 150MHz, for DDR mode,
SD card clock can't exceed 45MHz. This patch change to use the
new compatible "fsl,imx6ull-usdhc" to follow this limitation.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since imx6ulz.dtsi includes imx6ull.dtsi, we only need to fix the compatible
string here to achieve the correct OTP size for both SoCs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This was implemented in the driver but not actually defined and
referenced in dts. This makes it always on.
From reference manual in section "10.4.1.4.1 Power Distribution":
"Display domain - The DISPLAY domain contains GIS, CSI, PXP, LCDIF,
PCIe, DCIC, and LDB. It is supplied by internal regulator."
The current pd_pcie is actually only for PCIE_PHY, the PCIE ip block is
actually inside the DISPLAY domain. Handle this by adding the pcie node
in both power domains.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull y2038 - time64 system calls from Arnd Bergmann:
This series finally gets us to the point of having system calls with 64-bit
time_t on all architectures, after a long time of incremental preparation
patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures using
the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call that
includes a 'struct timespec' argument, or a structure containing a timespec
or (in case of clock_adjtime) timeval. Not included here are new versions
of getitimer/setitimer and getrusage/waitid, which are planned for the
future but only needed to make a consistent API rather than for correct
operation beyond y2038. These four system calls are based on 'timeval', and
it has not been finally decided what the replacement kernel interface will
use instead.
So far, I have done a lot of build testing across most architectures, which
has found a number of bugs. Runtime testing so far included testing LTP on
32-bit ARM with the existing system calls, to ensure we do not regress for
existing binaries, and a test with a 32-bit x86 build of LTP against a
modified version of the musl C library that has been adapted to the new
system call interface [3]. This library can be used for testing on all
architectures supported by musl-1.1.21, but it is not how the support is
getting integrated into the official musl release. Official musl support is
planned but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
|
|
git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull preparatory work for y2038 changes from Arnd Bergmann:
System call unification and cleanup
The system call tables have diverged a bit over the years, and a number of
the recent additions never made it into all architectures, for one reason
or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all architectures
but that we definitely want there. This includes {,f}statfs64() and
get{eg,eu,g,p,u,pp}id() on alpha, which have been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like what we
do on other architectures, while keeping the 31-bit pointer
extension. This was merged as a shared branch by the s390 maintainers
and is included here in order to base the other patches on top.
- Add the separate ipc syscalls on all architectures that traditionally
only had sys_ipc(). This version is done without support for IPC_OLD
that is we have in sys_ipc. The new semtimedop_time64 syscall will only
be added here, not in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably don't need
everywhere, in particular pkey_* and rseq, for the purpose of symmetry:
if it's in asm-generic/unistd.h, it makes sense to have it everywhere. I
expect that any future system calls will get assigned on all platforms
together, even when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future calls. In
combination with the generated tables, this hopefully makes it easier to
add new calls across all architectures together.
All of the above are technically separate from the y2038 work, but are done
as preparation before we add the new 64-bit time_t system calls everywhere,
providing a common baseline set of system calls.
I expect that glibc and other libraries that want to use 64-bit time_t will
require linux-5.1 kernel headers for building in the future, and at a much
later point may also require linux-5.1 or a later version as the minimum
kernel at runtime. Having a common baseline then allows the removal of many
architecture or kernel version specific workarounds.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A handful of fixes:
- Fix an MCE corner case bug/crash found via MCE injection testing
- Fix 5-level paging boot crash
- Fix MCE recovery cache invalidation bug
- Fix regression on Xen guests caused by a recent PMD level mremap
speedup optimization"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Make set_pmd_at() paravirt aware
x86/mm/cpa: Fix set_mce_nospec()
x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of kernel side fixes:
- Fix the Intel uncore driver on certain hardware configurations
- Fix a CPU hotplug related memory allocation bug
- Remove a spurious WARN()
... plus also a handful of perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script python: Add Python3 support to tests/attr.py
perf trace: Support multiple "vfs_getname" probes
perf symbols: Filter out hidden symbols from labels
perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
tools headers uapi: Sync linux/in.h copy from the kernel sources
perf clang: Do not use 'return std::move(something)'
perf mem/c2c: Fix perf_mem_events to support powerpc
perf tests evsel-tp-sched: Fix bitwise operator
perf/core: Don't WARN() for impossible ring-buffer sizes
perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
perf/x86/intel/uncore: Add Node ID mask
|
|
set_pmd_at() calls native_set_pmd() unconditionally on x86. This was
fine as long as only huge page entries were written via set_pmd_at(),
as Xen pv guests don't support those.
Commit 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions")
introduced a usage of set_pmd_at() possible on pv guests, leading to
failures like:
BUG: unable to handle kernel paging request at ffff888023e26778
#PF error: [PROT] [WRITE]
RIP: e030:move_page_tables+0x7c1/0xae0
move_vma.isra.3+0xd1/0x2d0
__se_sys_mremap+0x3c6/0x5b0
do_syscall_64+0x49/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Make set_pmd_at() paravirt aware by just letting it use set_pmd().
Fixes: 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: xen-devel@lists.xenproject.org
Cc: boris.ostrovsky@oracle.com
Cc: sstabellini@kernel.org
Cc: hpa@zytor.com
Cc: bp@alien8.de
Cc: torvalds@linux-foundation.org
Link: https://lkml.kernel.org/r/20190210074056.11842-1-jgross@suse.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A batch of MIPS fixes for 5.0, nothing too scary.
- A workaround for a Loongson 3 CPU bug is the biggest change, but
still fairly straightforward. It adds extra memory barriers (sync
instructions) around atomics to avoid a CPU bug that can break
atomicity.
- Loongson64 also sees a fix for powering off some systems which
would incorrectly reboot rather than waiting for the power down
sequence to complete.
- We have DT fixes for the Ingenic JZ4740 SoC & the JZ4780-based Ci20
board, and a DT warning fix for the Nexsys4/MIPSfpga board.
- The Cavium Octeon platform sees a further fix to the behaviour of
the pcie_disable command line argument that was introduced in v3.3.
- The VDSO, introduced in v4.4, sees build fixes for configurations
of GCC that were built using the --with-fp-32= flag to specify a
default 32-bit floating point ABI.
- get_frame_info() sees a fix for configurations with
CONFIG_KALLSYMS=n, for which it previously always returned an
error.
- If the MIPS Coherence Manager (CM) reports an error then we'll now
clear that error correctly so that the GCR_ERROR_CAUSE register
will be updated with information about any future errors"
* tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
MIPS: Remove function size check in get_frame_info()
MIPS: Use lower case for addresses in nexys4ddr.dts
MIPS: Loongson: Introduce and use loongson_llsc_mb()
MIPS: VDSO: Include $(ccflags-vdso) in o32,n32 .lds builds
MIPS: VDSO: Use same -m%-float cflag as the kernel proper
MIPS: OCTEON: don't set octeon_dma_bar_type if PCI is disabled
DTS: CI20: Fix bugs in ci20's device tree.
MIPS: DTS: jz4740: Correct interrupt number of DMA core
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, fixing namespace locking when
dealing with the effects log, and a rapid add/remove issue (Keith)
- blktrace tweak, ensuring requests with -1 sectors are shown (Jan)
- link power management quirk for a Smasung SSD (Hans)
- m68k nfblock dynamic major number fix (Chengguang)
- series fixing blk-iolatency inflight counter issue (Liu)
- ensure that we clear ->private when setting up the aio kiocb (Mike)
- __find_get_block_slow() rate limit print (Tetsuo)
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two very minor fixes: one remove of a #include for an unused header
and a fix of the xen ML address in MAINTAINERS"
* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: unify reference to xen-devel list
arch/arm/xen: Remove duplicate header
|
|
Add devicetree support for Sophon Edge board from Bitmain based on
BM1880 SoC. This board is one of the 96Boards Consumer and AI platform.
More information about this board can be found in 96Boards product page:
https://www.96boards.org/documentation/consumer/sophon-edge/
Only UART peripheral support is enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add devicetree support for Bitmain BM1880 SoC, consisting of a Dual
core ARM Cortex A53 subsystem, a Single core RISC-V subsystem and a Tensor
Processor subsystem. Only ARM Cortex A53 Application processor subsystem
support is enabled for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add ARCH_BITMAIN for supporting Bitmain SoC platforms.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a bit larger than normal, as we had not managed to send out a
pull request before traveling for a week without my signing key.
There are multiple code fixes for older bugs, all of which should get
backported into stable kernels:
- tango: one fix for multiplatform configurations broken on other
platforms when tango is enabled
- arm_scmi: device unregistration fix
- iop32x: fix kernel oops from extraneous __init annotation
- pxa: remove a double kfree
- fsl qbman: close an interrupt clearing race
The rest is the usual collection of smaller fixes for device tree
files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
imx platforms.
Some of these are for compile-time warnings, most are for board
specific functionality that fails to work because of incorrect
settings"
* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
firmware: arm_scmi: provide the mandatory device release callback
ARM: iop32x/n2100: fix PCI IRQ mapping
arm64: dts: add msm8996 compatible to gicv3
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: pxa: ssp: unneeded to free devm_ allocated data
ARM: dts: r8a7743: Convert to new LVDS DT bindings
soc: fsl: qbman: avoid race in clearing QMan interrupt
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
ARM: dts: da850: fix interrupt numbers for clocksource
dt-bindings: imx8mq: Number clocks consecutively
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two arm64 fixes for -rc6. They resolve a kernel NULL dereference in
kexec and bogus kernel page table dumping when userspace is configured
for 52-bit virtual addressing.
Summary:
- Fix kernel oops when attemping kexec_file() with a NULL cmdline
- Fix page table output in debugfs when ARM64_USER_VA_BITS_52=y"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: handle empty command-line
arm64: ptdump: Don't iterate kernel page tables using PTRS_PER_PXX
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Just two fixes, both going to stable.
- Our support for split pmd page table lock had a bug which could
lead to a crash on mremap() when using the Radix MMU (Power9 only).
- A fix for the PAPR SCM driver (nvdimm) we added last release, which
had a bug where we might mis-handle a hypervisor response leading
to us failing to attach the memory region.
Thanks to: Aneesh Kumar K.V, Oliver O'Halloran"
* tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Use the correct bind address
powerpc/radix: Fix kernel crash with mremap()
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This augments the CBUS GPIO I2C driver to use GPIO
descriptors for clock, sel and data. We drop the platform
data that was only used for carrying GPIO numbers and
use machine descriptor tables instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Reference the PHY nodes from the USB controller nodes.
The USB3 host controller is wired to:
* the first PHY of the COMPHY IP
* the OTG-capable UTMI PHY
The USB2 host controller is wired to:
* the host-only UTMI PHY
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The SATA node is wired to the third PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The PCIe node is wired to the second PHY of the COMPHY IP.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Describe the A3700 COMPHY node. It has three PHYs that can be
configured as follow:
* PCIe or GbE
* USB3 or GbE
* SATA or USB3
Each of them has its own memory area.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
By using the new binding for the partitions for the flashes we don't need
anymore to use #size-cells and #address-cells at the flash node level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The mv88e6341 ethernet switch needs the cpu port control register to be
set with TX and RX internal delay in order to work.
This fixes ethernet support on system booted via a bootloader that
has not already configured this register (e.g. mainline u-boot, or
vendor u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
In order to be able to communicate with the 88e6341 switch some pins
have to be repurposed as RGMII and SMI pins.
This fixes ethernet support on system booted via a bootloader that
has not already configured those pins (e.g. mainline u-boot, or vendor
u-boot compiled without ethernet support).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The reset signal of the SSD1306 OLED display is actually active-low.
Adapt the DT to reflect the real world.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>,
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
|
|
Add the G12a (S905X2) based X96 Max board[1].
There is no branding for the manufacturer anywhere on the product, so it
took some digging[2] to find the manufacturer. But since there's
nothing about the maker on the product I've left it out of the DT name
because 1) nobody will know that name and 2) keeps the DT filename
shorter.
[1] https://www.cnx-software.com/2018/09/25/x96-max-amlogic-s905x2-tv-box/
[2] https://fccid.io/2AI6D-X96MAX
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the peripheral clock controller to the g12a SoC DT
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable the g12a clock controller for ARCH_MESON
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
These have been disable since the change to probe Marvell Ethernet
switches as MDIO devices. Remove the properties now that the code to
suppport them will also be removed soon.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds initial support for micro-DPU (uDPU) board which is based on
Armada-3720 SoC. micro-DPU is the single-port FTTdp distribution point
unit made by Methode Electronics which offers complete modularity with
replaceable SFP modules both for uplink and downlink (G.hn over
twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
In order to drop the hard-coded GPIO base values from the davinci GPIO
driver's platform data, we first need to get rid of all calls to the
legacy GPIO functions. Convert the mdio configuration to hogging the
relevant GPIO line in the da850-evm board file.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
WARNING: vmlinux.o(.text.unlikely+0x1c05): Section mismatch in
reference from the function init_xstate_size() to the
function .init.text:get_xsave_size()
WARNING: vmlinux.o(.text.unlikely+0x1c19): Section mismatch in
reference from the function init_xstate_size() to the
function .init.text:get_xsaves_size()
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Link: https://lkml.kernel.org/r/20190108130225.5066-2-sergey.senozhatsky@gmail.com
|
|
WARNING: vmlinux.o(.text.unlikely+0x498d): Section mismatch in reference
from the function percpu_setup_debug_store() to the function
.init.text:cea_map_percpu_pages()
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Link: https://lkml.kernel.org/r/20190108130225.5066-1-sergey.senozhatsky@gmail.com
|
|
Compiling the kernel with W=1 results in the following warning:
arch/x86/kernel/cpu/mtrr/cleanup.c:299:16: warning: variable ‘second_basek’ set but not used [-Wunused-but-set-variable]
unsigned long second_basek, second_sizek;
Remove the unused variable.
[ tglx: Massaged changelog ]
Signed-off-by: Bo Yu <tsu.yubo@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: puwen@hygon.cn
Link: https://lkml.kernel.org/r/20190208125343.11451-1-tsu.yubo@gmail.com
|
|
The recent commit fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and
cpa_flush_array() into a single cpa_flush() function") accidentally made
the call to make_addr_canonical_again() go away, which breaks
set_mce_nospec().
Re-instate the call to convert the address back into canonical form right
before invoking either CLFLUSH or INVLPG. Rename the function while at it
to be shorter (and less MAGA).
Fixes: fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and cpa_flush_array() into a single cpa_flush() function")
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lkml.kernel.org/r/20190208120859.GH32511@hirez.programming.kicks-ass.net
|
|
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch enables PCIEC0 PCI express controller on the sub board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Silicon Linux CAT 874 board has 2GB DDR memory. Update the dma-ranges
mapping for pciec0 node. Also declare pcie bus clock, since it is
generated on the CAT874 main board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds TMU{0|1|2|3|4} device nodes for r8a774c0 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a774c0 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch defines OOP tables for all CPUs, similarly to
what done by Takeshi Kihara and Yoshihiro Kaneko for the
R8A77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch define OOP tables for all CPUs.
This allows CPUFreq to function.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Successfully tested on H3 ES2.0 and M3-N ES1.0.
Transfer rates where >160MB/s for H3 and >200MB/s for M3-N.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add LVDS encoder node to r8a7744 SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add du node to r8a7744 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The arm64 NEON bit-sliced implementation of AES-CTR fails the improved
skcipher tests because it sometimes produces the wrong ciphertext. The
bug is that the final keystream block isn't returned from the assembly
code when the number of non-final blocks is zero. This can happen if
the input data ends a few bytes after a page boundary. In this case the
last bytes get "encrypted" by XOR'ing them with uninitialized memory.
Fix the assembly code to return the final keystream block when needed.
Fixes: 88a3f582bea9 ("crypto: arm64/aes - don't use IV buffer to return final keystream block")
Cc: <stable@vger.kernel.org> # v4.11+
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
