| Age | Commit message (Collapse) | Author |
|---|
|
The Tegra Combined UART is used on some Tegra194 devices as a way of
multiplexing output from multiple producers onto a single physical UART.
Enable this by default so that it can be used as the default console to
write kernel messages to.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra210 Smaug board uses MAX77621 for both CPU & GPU rail. Note
that max8973 and max77621 share the same driver. So enable this driver
for the PMIC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The IODA reset is used to flush out any OS controlled state from the PHB.
This reset can fail if a PHB fatal error has occurred in early boot,
probably due to a because of a bad device. We already do a fundemental
reset of the device in some cases, so this patch just adds a test to force
a full reset if firmware reports an error when performing the IODA reset.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
'regno' is directly controlled by user space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
On PTRACE_SETREGS and PTRACE_GETREGS requests, user space passes the
register number that would be read or written. This register number is
called 'regno' which is part of the 'addr' syscall parameter.
This 'regno' value is checked against the maximum pt_regs structure size,
and then used to dereference it, which matches the initial part of a
Spectre v1 (and Spectre v1.1) attack. The dereferenced value, then,
is returned to userspace in the GETREGS case.
This patch sanitizes 'regno' before using it to dereference pt_reg.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki Poulouse <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-2-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
One pin can be muxed as PCIe endpoint card reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The SATA IP get its clock from the north-bridge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fix the SATA IP memory area which is only 0x178 bytes long (from
Marvell A3700 specification). Actually, starting from the offset
0xe0178, there is an area dedicated to the COMPHY driver.
Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add interrupt properties in the thermal node as well as a critical trip
point in the thermal-zone.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
When building randconfigs, one of the failures is:
ld: arch/x86/boot/compressed/kaslr.o: in function `choose_random_location':
kaslr.c:(.text+0xbf7): undefined reference to `count_immovable_mem_regions'
ld: kaslr.c:(.text+0xcbe): undefined reference to `immovable_mem'
make[2]: *** [arch/x86/boot/compressed/vmlinux] Error 1
because CONFIG_ACPI is not enabled in this particular .config but
CONFIG_MEMORY_HOTREMOVE is and count_immovable_mem_regions() is
unresolvable because it is defined in compressed/acpi.c which is the
compilation unit that depends on CONFIG_ACPI.
Add CONFIG_ACPI to the explicit dependencies for MEMORY_HOTREMOVE.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190205131033.9564-1-bp@alien8.de
|
|
ac09c5f43cf6 ("x86/boot: Build the command line parsing code unconditionally")
enabled building the command line parsing code unconditionally but it
forgot to remove the respective ifdeffery around the prototypes in the
misc.h header, leading to
arch/x86/boot/compressed/acpi.c: In function ‘get_acpi_rsdp’:
arch/x86/boot/compressed/acpi.c:37:8: warning: implicit declaration of function \
‘cmdline_find_option’ [-Wimplicit-function-declaration]
ret = cmdline_find_option("acpi_rsdp", val, MAX_ADDR_LEN);
^~~~~~~~~~~~~~~~~~~
for configs where neither CONFIG_EARLY_PRINTK nor CONFIG_RANDOMIZE_BASE
was defined.
Drop the ifdeffery in the header too.
Fixes: ac09c5f43cf6 ("x86/boot: Build the command line parsing code unconditionally")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/5c51daf0.83pQEkvDZILqoSYW%lkp@intel.com
Link: https://lkml.kernel.org/r/20190205131352.GA27396@zn.tnic
|
|
Add a build option and a command line parameter to build and enable the
support of pseudo-NMIs.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When an NMI is raised while interrupts where disabled, the IRQ tracing
already is in the correct state (i.e. hardirqs_off) and should be left
as such when returning to the interrupted context.
Check whether PMR was masking interrupts when the NMI was raised and
skip IRQ tracing if necessary.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Handling of an NMI should not set any TIF flags. For NMIs received from
EL0 the current exit path is safe to use.
However, an NMI received at EL1 could have interrupted some task context
that has set the TIF_NEED_RESCHED flag. Preempting a task should not
happen as a result of an NMI.
Skip preemption after handling an NMI from EL1.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Per definition of the daifflags, Serrors can occur during any interrupt
context, that includes NMI contexts. Trying to nmi_enter in an nmi context
will crash.
Skip nmi_enter/nmi_exit when serror occurred during an NMI.
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Implement architecture specific primitive allowing the GICv3 driver to
use priorities to mask interrupts.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Once the boot CPU has been prepared or a new secondary CPU has been
brought up, use ICC_PMR_EL1 to mask interrupts on that CPU and clear
PSR.I bit.
Since ICC_PMR_EL1 is initialized at CPU bringup, avoid overwriting
it in the GICv3 driver.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Currently alternatives are applied very late in the boot process (and
a long time after we enable scheduling). Some alternative sequences,
such as those that alter the way CPU context is stored, must be applied
much earlier in the boot sequence.
Introduce apply_boot_alternatives() to allow some alternatives to be
applied immediately after we detect the CPU features of the boot CPU.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[julien.thierry@arm.com: rename to fit new cpufeature framework better,
apply BOOT_SCOPE feature early in boot]
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In preparation for the application of alternatives at different points
during the boot process, provide the possibility to check whether
alternatives for a feature of interest was already applied instead of
having a global boolean for all alternatives.
Make VHE enablement code check for the VHE feature instead of considering
all alternatives.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: Christoffer Dall <Christoffer.Dall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The addition of PMR should not bypass the semantics of daifflags.
When DA_F are set, I bit is also set as no interrupts (even of higher
priority) is allowed.
When DA_F are cleared, I bit is cleared and interrupt enabling/disabling
goes through ICC_PMR_EL1.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Instead disabling interrupts by setting the PSR.I bit, use a priority
higher than the one used for interrupts to mask them via PMR.
When using PMR to disable interrupts, the value of PMR will be used
instead of PSR.[DAIF] for the irqflags.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Interrupts masked by ICC_PMR_EL1 will not be signaled to the CPU. This
means that hypervisor will not receive masked interrupts while running a
guest.
We need to make sure that all maskable interrupts are masked from the
time we call local_irq_disable() in the main run loop, and remain so
until we call local_irq_enable() after returning from the guest, and we
need to ensure that we see no interrupts at all (including pseudo-NMIs)
in the middle of the VM world-switch, while at the same time we need to
ensure we exit the guest when there are interrupts for the host.
We can accomplish this with pseudo-NMIs enabled by:
(1) local_irq_disable: set the priority mask
(2) enter guest: set PSTATE.I
(3) clear the priority mask
(4) eret to guest
(5) exit guest: set the priotiy mask
clear PSTATE.I (and restore other host PSTATE bits)
(6) local_irq_enable: clear the priority mask.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
CPU does not received signals for interrupts with a priority masked by
ICC_PMR_EL1. This means the CPU might not come back from a WFI
instruction.
Make sure ICC_PMR_EL1 does not mask interrupts when doing a WFI.
Since the logic of cpu_do_idle is becoming a bit more complex than just
two instructions, lets turn it from ASM to C.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In order to replace PSR.I interrupt disabling/enabling with ICC_PMR_EL1
interrupt masking, ICC_PMR_EL1 needs to be saved/restored when
taking/returning from an exception. This mimics the way hardware saves
and restores PSR.I bit in spsr_el1 for exceptions and ERET.
Add PMR to the registers to save in the pt_regs struct upon kernel entry,
and restore it before ERET. Also, initialize it to a sane value when
creating new tasks.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Introduce fixed values for PMR that are going to be used to mask and
unmask interrupts by priority.
The current priority given to GIC interrupts is 0xa0, so clearing PMR's
most significant bit is enough to mask interrupts.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Mask the IRQ priority through PMR and re-enable IRQs at CPU level,
allowing only higher priority interrupts to be received during interrupt
handling.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add helper functions to access system registers related to interrupt
priorities: PMR and RPR.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add a cpufeature indicating whether a cpu supports masking interrupts
by priority.
The feature will be properly enabled in a later patch.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
It is not supported to have some CPUs using GICv3 sysreg CPU interface
while some others do not.
Once ICC_SRE_EL1.SRE is set on a CPU, the bit cannot be cleared. Since
matching this feature require setting ICC_SRE_EL1.SRE, it cannot be
turned off if found on a CPU.
Set the feature as STRICT_BOOT, if boot CPU has it, all other CPUs are
required to have it.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
There are some helpers to modify PSR.[DAIF] bits that are not referenced
anywhere. The less these bits are available outside of local_irq_*
functions the better.
Get rid of those unused helpers.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When using VHE, the host needs to clear HCR_EL2.TGE bit in order
to interact with guest TLBs, switching from EL2&0 translation regime
to EL1&0.
However, some non-maskable asynchronous event could happen while TGE is
cleared like SDEI. Because of this address translation operations
relying on EL2&0 translation regime could fail (tlb invalidation,
userspace access, ...).
Fix this by properly setting HCR_EL2.TGE when entering NMI context and
clear it if necessary when returning to the interrupted context.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
KVM makes use of check_switch_mmu_context(), check_mmu_context() &
get_new_mmu_context() which are no longer static inline functions in a
header. As such they need to be exported for KVM to successfully build
as a module, which was previously overlooked. Add the missing exports.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 4ebea49ce233 ("MIPS: mm: Un-inline get_new_mmu_context")
Fixes: 42d5b846574f ("MIPS: mm: Unify ASID version checks")
|
|
This commit adds a BPF JIT for RV64G.
The JIT is a two-pass JIT, and has a dynamic prolog/epilogue (similar
to the MIPS64 BPF JIT) instead of static ones (e.g. x86_64).
At the moment the RISC-V Linux port does not support
CONFIG_HAVE_KPROBES, which means that CONFIG_BPF_EVENTS is not
supported. Thus, no tests involving BPF_PROG_TYPE_TRACEPOINT,
BPF_PROG_TYPE_PERF_EVENT, BPF_PROG_TYPE_KPROBE and
BPF_PROG_TYPE_RAW_TRACEPOINT passes.
The implementation does not support "far branching" (>4KiB).
Test results:
# modprobe test_bpf
test_bpf: Summary: 378 PASSED, 0 FAILED, [366/366 JIT'ed]
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier
...
Summary: 761 PASSED, 507 SKIPPED, 2 FAILED
Note that "test_verifier" was run with one build with
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y and one without, otherwise
many of the the tests that require unaligned access were skipped.
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y:
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier | grep -c 'NOTE.*unknown align'
0
No CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS:
# echo 1 > /proc/sys/kernel/unprivileged_bpf_disabled
# ./test_verifier | grep -c 'NOTE.*unknown align'
59
The two failing test_verifier tests are:
"ld_abs: vlan + abs, test 1"
"ld_abs: jump around ld_abs"
This is due to that "far branching" involved in those tests.
All tests where done on QEMU (QEMU emulator version 3.1.50
(v3.1.0-688-g8ae951fbc106)).
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Assure a GISA is in use before accessing the IPM to avoid a
null pointer dereference issue.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-16-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
By initializing the GIB, it will be used by the kvm host.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-15-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
The patch implements a handler for GIB alert interruptions
on the host. Its task is to alert guests that interrupts are
pending for them.
A GIB alert interrupt statistic counter is added as well:
$ cat /proc/interrupts
CPU0 CPU1
...
GAL: 23 37 [I/O] GIB Alert
...
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-14-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Function kvm_s390_gisa_clear() now clears the Interruption
Pending Mask of the GISA asap. If the GISA is in the alert
list at this time it stays in the list but is removed by
process_gib_alert_list().
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-13-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Add the Interruption Alert Mask (IAM) to the architecture specific
kvm struct. This mask in the GISA is used to define for which ISC
a GIB alert will be issued.
The functions kvm_s390_gisc_register() and kvm_s390_gisc_unregister()
are used to (un)register a GISC (guest ISC) with a virtual machine and
its GISA.
Upon successful completion, kvm_s390_gisc_register() returns the
ISC to be used for GIB alert interruptions. A negative return code
indicates an error during registration.
Theses functions will be used by other adapter types like AP and PCI to
request pass-through interruption support.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-12-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Adding the kvm reference to struct sie_page2 will allow to
determine the kvm a given gisa belongs to:
container_of(gisa, struct sie_page2, gisa)->kvm
This functionality will be required to process a gisa in
gib alert interruption context.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-11-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
The Guest Information Block (GIB) links the GISA of all guests
that have adapter interrupts pending. These interrupts cannot be
delivered because all vcpus of these guests are currently in WAIT
state or have masked the respective Interruption Sub Class (ISC).
If enabled, a GIB alert is issued on the host to schedule these
guests to run suitable vcpus to consume the pending interruptions.
This mechanism allows to process adapter interrupts for currently
not running guests.
The GIB is created during host initialization and associated with
the Adapter Interruption Facility in case an Adapter Interruption
Virtualization Facility is available.
The GIB initialization and thus the activation of the related code
will be done in an upcoming patch of this series.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-10-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
This patch implements the Set Guest Information Block operation
to request association or disassociation of a Guest Information
Block (GIB) with the Adapter Interruption Facility. The operation
is required to receive GIB alert interrupts for guest adapters
in conjunction with AIV and GISA.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-9-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Use this struct analog to the kvm interruption structs
for kvm emulated floating and local interruptions.
GIB handling will add further fields to this structure as
required.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-8-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
This will shorten the length of code lines. All GISA related
static inline functions are local to interrupt.c.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-7-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
