| Age | Commit message (Collapse) | Author |
|---|
|
Add SCM DT node to enable SCM functionality on SDM845.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Correct address for pcs_misc register region of USB3 QMP UNI PHY.
These registers are used during runtime-suspend/resume routines
of phy.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: ca4db2b538a1 ("arm64: dts: qcom: sdm845: Add USB-related nodes")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This adds the low pass audio clock controller node to sdm845 based on
the example in the bindings.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[bjorn: Disabled lpasscc node, as it's normally protected]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This adds the video clock controller node to sdm845 based on the examples
in the bindings.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the GPU clock controller nodes as per the example.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This adds the Quad SPI controller to the main sdm845 device tree file.
Boards will be expected to assign the proper pinctrl depending on how
many chip selects they have hooked up and how many data lines.
This depends on commit 48735597f7bd ("clk: qcom: Add qspi (Quad SPI)
clock defines for sdm845 to header") to add the needed defines. It
also shouldn't land until the patch ("dt-bindings: spi: Qualcomm Quad
SPI(QSPI) documentation") [1] lands.
[1] https://lkml.kernel.org/r/20181002214709.162330-1-ryandcase@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
msm8998 has a dozen i2c controllers which can be used to connect to board
specific peripherals. Enumerate the controllers so that boards can wire
up as needed.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[bjorn: Renumbered labels on BLSP2 nodes]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
l21 is used as sdcard vmmc, and needs the load increased to prevent
voltage drop issues with some sdcards. This addresses -84 errors seen
during sdcard init with SDR104 cards.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
|
|
DPU is short for the Display Processing Unit. It is the display
controller on Qualcomm SDM845 chips.
This change adds MDSS and DSI nodes to enable display on the
target device.
Changes in v2:
- Beefed up commit message
- Use SoC specific compatibles for mdss and dpu (Rob H)
- Use assigned-clocks to set initial clock frequency(Rob H)
Changes in v3:
- added IOMMU node
- Fix device naming (remove _phys)
- Use correct IRQ_TYPE in interrupt specifiers
Changes in v4:
- move mdss node to preserve the unit address sort order
- remove _clk suffix from dsi clocks
(both the comments are from Doug Anderson)
Changes in v5:
- Keep the device status "disabled" by default (Bjorn Andersson)
- Use MDSS_GDSC macro (Jordan)
- Fix phy-names (Jordan)
- List reg ranges in numerical order (Jordan)
Changes in v6:
- Separating this patch out of the series
- fix phy-names
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add compatible to gicv3 node to enable quirk required to restrict writing
to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor.
With this quirk MSM8996 can at least boot out of mainline, which can help
community to work with boards based on MSM8996.
Without this patch Qualcomm DB820c board reboots on mainline.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
ccount_timer_shutdown is called from the atomic context in the
secondary_start_kernel, resulting in the following BUG:
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
Preemption disabled at:
secondary_start_kernel+0xa1/0x130
Call Trace:
___might_sleep+0xe7/0xfc
__might_sleep+0x41/0x44
synchronize_irq+0x24/0x64
disable_irq+0x11/0x14
ccount_timer_shutdown+0x12/0x20
clockevents_switch_state+0x82/0xb4
clockevents_exchange_device+0x54/0x60
tick_check_new_device+0x46/0x70
clockevents_register_device+0x8c/0xc8
clockevents_config_and_register+0x1d/0x2c
local_timer_setup+0x75/0x7c
secondary_start_kernel+0xb4/0x130
should_never_return+0x32/0x35
Use disable_irq_nosync instead of disable_irq to avoid it.
This is safe because the ccount timer IRQ is per-CPU, and once IRQ is
masked the ISR will not be called.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Commit c5418a0b98c1 ("usb: gadget: pxa25x_udc: move register definitions
from arch") removed inclusion of mach/pxa25x-udc.h from the PXA25x UDC
driver, the contents of the header file was also wiped out, however the
file itself hasn't been removed, now this change removes the unused empty
header file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
This is an ARM + FPGA instrumentation board used at telescopes in
Antarctica, Chile, and Canada:
https://pole.uchicago.edu/
https://arxiv.org/abs/1608.03025
https://chime-experiment.ca/
With these commits and a suitable userspace, we can boot the board, load
a FPGA bitstream, and communicate with the RTL design. Most of the board's
telemetry sensors (temperatures, voltages) are functional but detailed
testing is to follow.
We are weaning ourselves off TI's "official" kernel for this SOC, which
has been stuck at 2.6.37 and is not really fit for use. To anyone at TI:
despite good silicon and some dedicated support enginers, your
open-source software strategy for these parts has not worked well.
Please get in touch with me if you'd like to have a constructive
discussion about ways to improve it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: dropped fpga@1 as linux,spidev is still undocumented]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is no functional change here; the I2C and ELM entries leaked
into each other and this separates them again.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ethernet works in kernel only if we use some binary u-boot from the
past which have support for KS8851.
The u-boot sources are not available for this mysterious u-boot image
people tends to hold on... Mainline u-bott does not have ethernet support
for sdp4430 and if we use that the ethernet is not working.
After some debugging I have managed to get the ethernet working with
mainline u-boot while not breaking the networking with the case when we
boot with the mysterious binary u-boot.
Basically we were missing bunch of pinmux settings and the 'magic'
gpio_138 handling in kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adopt the SPDX license identifier headers to ease license
compliance management.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most of the legacy "linux,wakeup" boolean property is already replaced
with "wakeup-source". However few occurrences of old property has popped
up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit aeda5003d0b9 ("Input: matrix_keypad - change
name of wakeup property to "wakeup-source"")
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove the unnecessary properties #address-cells and #size-cells
of node pinmux as there are no child-nodes with property reg.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it. Code was tested on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Drop the A31 fallback compatible.
Fixes: f89120b6f554 ("ARM: dts: sun8i: Add the H3/H5 CSI controller")
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
As instability in the architectural timer has been observed on multiple
devices using this SoC, inluding the Pine64 and the Orange Pi Win,
enable the workaround in the SoC's device tree.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
In order to have a common code base for fscrypt "post read" processing
for all filesystems which support encryption, this commit removes
filesystem specific build config option (e.g. CONFIG_EXT4_FS_ENCRYPTION)
and replaces it with a build option (i.e. CONFIG_FS_ENCRYPTION) whose
value affects all the filesystems making use of fscrypt.
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
|
|
max_low_pfn should be pfn_size not byte_size.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Signed-off-by: Mao Han <mao_han@c-sky.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Commit 83a86fbb5b56 ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd01a ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
cd pin on mmc1 is GPIO_ACTIVE_LOW not GPIO_ACTIVE_HIGH
Fixes: e63201f19438 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We're currently getting a warning with make dtbs:
arch/arm/boot/dts/omap3-gta04.dtsi:720.7-727.4: Warning (graph_port):
/ocp@68000000/dss@48050000/encoder@48050c0 0/port: graph node unit
address error, expected "0"
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Wrong polarity of card detect GPIO pin leads to the system not
booting from external mmc, if the back cover of N900 is closed.
When the cover is open the system boots fine.
This wasn't noticed before, because of a bug, which was fixed
by commit e63201f19 (mmc: omap_hsmmc: Delete platform data GPIO
CD and WP).
Kernels up to 4.19 ignored the card detect GPIO from DT.
Fixes: e63201f19438 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This allows acceleration of cryptography inside QEMU.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Enable generic PCIe by default in the RISC-V defconfig, this allows us
to use QEMU's PCIe support out of the box. CONFIG_RAS=y is
automatically selected by generic PCIe, so it has been dropped from
the defconfig.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
[Palmer: Split out PCIE_XILINX and CRYPTO_DEV_VIRTIO]
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Xen-swiotlb hooks into the arm/arm64 arch code through a copy of the DMA
DMA mapping operations stored in the struct device arch data.
Switching arm64 to use the direct calls for the merged DMA direct /
swiotlb code broke this scheme. Replace the indirect calls with
direct-calls in xen-swiotlb as well to fix this problem.
Fixes: 356da6d0cde3 ("dma-mapping: bypass indirect calls for dma-direct")
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
|
|
eb01d42a7778 ("PCI: consolidate PCI config entry in drivers/pci")
reorganized the PCI-related Kconfig entries and resulted in a diff in
our defconfig. This simply removes the diff.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
There is no CONFIG_64BITS Kconfig macro.
Please see arch/riscv/Kconfig for details, e.g.
linux$ git grep -HnA 1 "config 64BIT" arch/riscv/Kconfig
arch/riscv/Kconfig:6:config 64BIT
arch/riscv/Kconfig-7- bool
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
of_find_node_by_type already calls of_node_put, don't call it again.
Fixes: 94f9bf118f ("RISC-V: Fix of_node_* refcount")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
The cond_resched() can be used to yield the CPU resource if
CONFIG_PREEMPT is not defined. Otherwise, cond_resched() is a dummy
function. In order to avoid kernel thread occupying entire CPU,
when CONFIG_PREEMPT=y, the kernel thread needs to follow the
rescheduling mechanism like a user thread.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
devm_ allocated data will be automatically freed. The free
of devm_ allocated data is invalid.
Fixes: 1c459de1e645 ("ARM: pxa: ssp: use devm_ functions")
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[title's prefix changed]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- Do not claim to run under z/VM if the hypervisor can not be
identified
- Fix crashes due to outdated ASCEs in CR1
- Avoid a deadlock in regard to CPU hotplug
- Really fix the vdso mapping issue for compat tasks
- Avoid crash on restart due to an incorrect stack address
* tag 's390-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/smp: Fix calling smp_call_ipl_cpu() from ipl CPU
s390/vdso: correct vdso mapping for compat tasks
s390/smp: fix CPU hotplug deadlock with CPU rescan
s390/mm: always force a load of the primary ASCE on context switch
s390/early: improve machine detection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux into features
Pull tip branch with Arnds compat system call wrapper rework.
|
|
When converting to autogenerated compat syscall wrappers all system
call entry points got a different symbol name: they all got a __s390x_
prefix.
This caused breakage with system call tracing, since an appropriate
arch_syscall_match_sym_name() was not provided. Add this function, and
while at it also add code to avoid compat system call tracing. s390
has different system call tables for native 64 bit system calls and
compat system calls. This isn't really supported in the common
code. However there are hardly any compat binaries left, therefore
just ignore compat system calls, like x86 and arm64 also do for the
same reason.
Fixes: aa0d6e70d3b3 ("s390: autogenerate compat syscall wrappers")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
It's also a slave controller driver now, calling it "master" is slightly
misleading.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch enable HDMI output on sun8i-h3-nanopi-m1-plus.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
