| Age | Commit message (Collapse) | Author |
|---|
|
These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
EHCI1 provides an HSIC interface. This interface is exposed on the
board through two pins among the GPIO header.
With the PHY now powered up and responding, enabling the interface when
nothing is connected results in a lot of error messages:
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 3 using ehci-platform
usb 2-1: device descriptor read/64, error -71
usb 2-1: device descriptor read/64, error -71
usb 2-1: new high-speed USB device number 4 using ehci-platform
usb 2-1: device not accepting address 4, error -71
usb 2-1: new high-speed USB device number 5 using ehci-platform
usb 2-1: device not accepting address 5, error -71
usb usb2-port1: unable to enumerate USB device
Disable it by default, but leave the entries in the board DTS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809's SW (switch) regulator is unused on the Cubieboard 4.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP809's SW (switch) regulator is unused on the A80 Optimus.
Add an empty node for it so that the OS can generate constraints.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ga10h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a node enabling the gsl3670 touchscreen controller found on
sun8i-a23-polaroid-mid2809pxe04 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add a node enabling the gsl1680 touchscreen controller found on
sun8i-a23-polaroid-mid2407pxe03 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The inet86dz tablet has a gsl1680 touchscreen,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gt90h tablet has a gsl3675 touchscreen, add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND,
an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI,
I2S and LCD.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The GR8 is an SoC made by Nextthing loosely based on the sun5i family.
Since it's not clear yet what we can factor out and merge with the A10s and
A13 support, let's keep it out of the sun5i.dtsi include tree. We will
figure out what can be shared when things settle down.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The usbphy and usb_otg nodes in the A23 and A33 dts files only differ
by compatible, and for the usbphy, the size of one of its register
regions.
Move all the common bits to the A23/A33 common dtsi file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The LCD output needs to be muxed. Add the proper pinctrl node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Add all the needed blocks to the A33 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that we have support for the CCU driver in sunxi-ng, convert the A23
and A33 DTs to that driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that we have a different clock representation, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The NanoPi NEO is a minimal H3 based SBC. It comes with 256/512M RAM, a
micro SD slot, 10/100Mbit ethernet and a single USB-A port.
Signed-off-by: James Pettigrew <james@innovum.com.au>
Reviewed-by: Rask Ingemann Lambertsen <ccc94453@vip.cybercity.dk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Most of the sun8i q8 boards have an SDIO wifi controller, on the
variants which use an USB wifi controller, this will result in a
couple of error msg-s in dmesg when proving the sdio bus and
an used mmc controller.
The best way to deal with wifi on this boards really is to simply
let the kernel auto-detect usb or sdio wifi controllers, so we
will just have to live with the few errors in dmesg.
This has been tested on a23 based q8 tablets with ESP8089, RTL8703AS and
RTL8189FTV wifi controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.
Note currently the dts is pretty much empty (except for including the
pc-plus dts), I've a local patch which enables the emac actually making
this dts different from the pc-plus one, but that needs the h3 emac
driver to get merged first.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Update the sun8i-h3-orangepi-plus.dts model string to reflect that it
is valid for both the Orange Pi Plus and the Orange Pi Plus 2.
This is also meant to help users realize that it is not valid for
the new Orange Pi Plus 2E, which will get its own dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features
volume buttons, micro-usb otg, headphone connector and a power button.
On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there
is also a accompanied board which has a Goodix GT9271 soldered.
As this board is desired to create tablets with a Home key dealed by
GT9271, a LED is present at the front panel at the position of the
Home key.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The R_PIO device node is missing #interrupt-cells, which causes
interrupt parsing to fail to match it as a valid interrupt controller.
Add #interrupt-cells to it. Also remove the unnecesary #address-cells
and #size-cells.
Fixes: 1ac56a6da9e1 ("ARM: dts: sun9i: Add A80 R_PIO pin controller device
node")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Rename the reference-design-tablet touchscreen node from gsl1680 to
touchscreen, all? tablets seem to use the same power and interrupt
gpio-s, but not all tablets use a gsl1680 controller making the
gsl1680 name somewhat misleading.
Also move the reg and compatible property to the actual tablet dts
as they may differ per tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13
tablet, with micro-usb (otg), headphone and micro-sd slots on the
outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
Note currently the dts for this is somewhat empty. This will change
once we add support for the touchscreen and accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in a nice cleanup :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
A23/A33 has a NAND controller which can now be used properly.
Add a device node for it.
The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.
Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.
The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The presence of the mma8452_int_e708_q1 node is a copy and paste
error, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.
Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.
Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.
This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables full otg support. I've tested that
this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add the AXP209 GPIO node to our AXP209 DTSI so that boards can use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This will allow u-boot to fill in a mac-address for Orange Pi 2
variants which use an sdio wifi without an eeprom for the mac.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Fix model and compatible]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
|
