| Age | Commit message (Collapse) | Author |
|---|
|
Zero clock rate doesn't make sense for PLLs and tegra-clk driver enters
into infinite loop on trying to calculate PLL parameters for zero rate.
Make code to error out if requested rate is zero.
Originally this trouble was found by Robert Yang while he was trying to
bring up upstream kernel on Samsung Galaxy Tab, which happened due to a
bug in Tegra DRM driver that erroneously sets PLL rate to zero. This
issues came over again recently during of kernel bring up on ASUS TF700T.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Higher SCLK rates on Tegra20 require high core voltage. The higher
clock rate may have a positive performance effect only for AHB DMA
transfers and AVP CPU, but both aren't used by upstream kernel at all.
Halve SCLK rate on Tegra20 in order to remove the high core voltage
requirement.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PLLU (USB) consists of the PLL configuration itself and configuration
of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114,
where T114 immediately bails out if PLLU is enabled and T30 re-enables
a potentially already enabled PLL (left after bootloader) and then fully
reprograms it, which could be unsafe to do. The correct way should be to
skip enabling of the PLL if it's already enabled and then apply
configuration to the outputs. This patch doesn't fix any known problems,
it's a minor improvement.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The refcounting of the gate clocks has a bug causing the enable_refcnt
to underflow when unused clocks are disabled. This happens because clk
provider erroneously bumps the refcount if clock is enabled at a boot
time, which it shouldn't be doing, and it does this only for the gate
clocks, while peripheral clocks are using the same gate ops and the
peripheral clocks are missing the initial bump. Hence the refcount of
the peripheral clocks is 0 when unused clocks are disabled and then the
counter is decremented further by the gate ops, causing the integer
underflow.
Fix this problem by removing the erroneous bump and by implementing the
disable_unused() callback, which disables the unused gates properly.
The visible effect of the bug is such that the unused clocks are never
gated if a loaded kernel module grabs the unused clocks and starts to use
them. In practice this shouldn't cause any real problems for the drivers
and boards supported by the kernel today.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The 600MHz is a too high clock rate for some SoC versions for the video
decoder hardware and this may cause stability issues. Use 300MHz for the
video decoder by default, which is supported by all hardware versions.
Fixes: ed1a2459e20c ("clk: tegra: Add Tegra20/30 EMC clock implementation")
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It is required for the series at [1] to let hantro driver aquire the
clock and set the rate for RK3036 correctly, but I didn't want to
add a patch for yet another subsystem to this series.
[1] https://lore.kernel.org/linux-media/20210525152225.154302-1-knaerzche@gmail.com/
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210528140736.79686-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
R-Car D3 ZA2 clock is from PLL0D3 or S0,
and it can be controlled by ZA2CKCR.
It is needed for R-Car Sound, but is not used so far.
Using default settings is very enough at this point.
This patch adds it by DEF_FIXED().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmxclrmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Make the style of the comment block for the Software Reset Clearing
Register offsets consistent with the comment blocks for the other
register offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/97dde75fe3ff27b9639c59a43cddbd9d5c405d0c.1620119700.git.geert+renesas@glider.be
|
|
The Realtime Module Stop Control Register definitions (RMSTPCR(i)) are
incorrect for i >= 8 on R-Car Gen2 and Gen3.
As these are unused, and not planned to be used, just like the
corresponding Modem Module Stop Control Register definitions (MMSTPCR())
on R-Mobile APE6 (they are intended for the software running on the
Real-Time and Modem CPU cores), they can just be removed.
Reported-by: Hai Nguyen Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/2d8bc4d9806b419ebb06030d2f31b2ea1e59b1d6.1620119700.git.geert+renesas@glider.be
|
|
The root clock generators with MND divider has the capability to support
change in duty-cycle by updating the 'D'. Add the clock ops which would
check all the boundary conditions and enable setting the desired duty-cycle
as per the consumer.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1619334502-9880-2-git-send-email-tdas@codeaurora.org
[sboyd@kernel.org: Remove _val everywhere]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Commit 46060be6d840 ("clk: sunxi-ng: v3s: use sigma-delta modulation for audio-pll")
changed the audio pll on the Allwinner V3s and V3 SoCs to use
sigma-delta modulation. In the process the declaration of fixed postdivider
providing "pll-audio" was adjusted to provide the desired clock rates from
the now sigma-delta modulated pll.
However, while the divider used for calculations by the clock framework
was adjusted the actual divider programmed into the hardware in
sun8i_v3_v3s_ccu_init was left at "divide by four". This broke the
"pll-audio" clock, now only providing quater the expected clock rate.
It would in general be desirable to program the postdivider for
"pll-audio" to four, such that a broader range of frequencies were
available on the pll outputs. But the clock for the integrated codec
"ac-dig" does not feature a mux that allows to select from all pll outputs
as it is just a simple clock gate connected to "pll-audio". Thus we need
to set the postdivider to one to be able to provide the 22.5792MHz and
24.576MHz rates required by the internal sun4i codec.
This patches fixes the incorrect clock rate by forcing the postdivider to
one in sun8i_v3_v3s_ccu_init.
Fixes: 46060be6d840 ("clk: sunxi-ng: v3s: use sigma-delta modulation for audio-pll")
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210513131315.2059451-1-t.schramm@manjaro.org
|
|
Use dev_err_probe() for clock and reset resources to indicate the deferral
reason through sysfs when waiting for the resource to come up.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210520073136.272925-1-jbrunet@baylibre.com
|
|
The cpll clk gate bits had an ordering issue. This led to the loss of
the boot sdmmc controller when the gmac was shut down with:
`ip link set eth0 down`
as the cpll_100m was shut off instead of the cpll_62p5.
cpll_62p5, cpll_50m, cpll_25m were all off by one with cpll_100m
misplaced.
Fixes: cf911d89c4c5 ("clk: rockchip: add clock controller for rk3568")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Elaine Zhang<zhangqing@rock-chips.com>
Link: https://lore.kernel.org/r/20210519174149.3691335-1-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
While some SoC samples are able to lock with a PLL factor of 55, others
samples can't. ATM, a minimum of 60 appears to work on all the samples
I have tried.
Even with 60, it sometimes takes a long time for the PLL to eventually
lock. The documentation says that the minimum rate of these PLLs DCO
should be 3GHz, a factor of 125. Let's use that to be on the safe side.
With factor range changed, the PLL seems to lock quickly (enough) so far.
It is still unclear if the range was the only reason for the delay.
Fixes: 085a4ea93d54 ("clk: meson: g12a: add peripheral clock controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429090325.60970-1-jbrunet@baylibre.com
|
|
This increases the maxmium supported frequency on 32-bit systems from
2^31 (signed long as used by clk_ops.round_rate, maximum value:
approx. 2.14GHz) to 2^32 (unsigned long as used by
clk_ops.determine_rate, maximum value: approx. 4.29GHz).
On Meson8/8b/8m2 the HDMI PLL and it's OD (post-dividers) are
capable of running at up to 2.97GHz. So switch the divider
implementation in clk-regmap to clk_ops.determine_rate to support these
higher frequencies on 32-bit systems.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210517203724.1006254-4-martin.blumenstingl@googlemail.com
|
|
Before the change: The sizeof rk3568_pll_rates = 2544
Use union: The sizeof rk3568_pll_rates = 1696
In future Soc, more PLL types will be added, and the
rockchip_pll_rate_table will add more members,
and the space savings will be even more pronounced
by using union.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Link: https://lore.kernel.org/r/20210511090726.15146-1-zhangqing@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the divider clocks on RZ/N1 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
Note that range checking is not yet implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7a384d02b85cdaac4a0e2b357582c8244b9a6f98.1617282116.git.geert+renesas@glider.be
|
|
Consider the minimum and maximum clock rates imposed by clock users when
calculating the most appropriate clock rate in the .determine_rate()
callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/35ceb262c71f1b2e9864a39bde9dafd78b2981f4.1617281699.git.geert+renesas@glider.be
|
|
Currently the .determine_rate() callback considers only the current
parent clock, limiting the range of achievable clock rates on DIV6
clocks with multiple parents, as found on SH/R-Mobile SoCs.
Extend the callback to consider all available parent clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/60e639692b462f99e0b6ab868c3675b3d97dbdb0.1617281699.git.geert+renesas@glider.be
|
|
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the DIV6 clocks on SH/R-Mobile and R-Car
SoCs from the old .round_rate() callback to the newer .determine_rate()
callback, which does not suffer from this limitation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fd8c45cd8bf5c6d928ca69c8b669be35b93de09.1617281699.git.geert+renesas@glider.be
|
|
Simplify the handling of the register bits to select the parent clock,
by storing a bitmask instead of separate shift and width values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5f05a5110d222ce5a113e683fe2aa726f4100b73.1617281699.git.geert+renesas@glider.be
|
|
As "div" is already "unsigned int", adding "U" suffixes to the constants
"1" and "64" allows us to replace the call to clamp_t() by a call to
clamp(). This removes hidden casts, and thus helps the compiler doing a
better job at type-checking.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2670c1e3c82a245666578cbbd1fb20d37932fd8e.1617281699.git.geert+renesas@glider.be
|
|
The error handling paths after pm_runtime_get_sync() have no refcount
decrement, which leads to refcount leak.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210415073338.22287-1-dinghao.liu@zju.edu.cn
[geert: Remove now unused variable priv]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for the ISPCS clocks on R-Car V3U.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210329223220.1139211-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for switching the Z and Z2 clocks between normal and boost
modes, by requesting clock rate changes to parent PLLs.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-8-geert+renesas@glider.be
|
|
Currently the PLLs are modeled as fixed factor clocks, based on initial
settings. However, enabling CPU boost clock rates requires increasing
the PLL clock rates.
Add a custom clock driver to model the PLL clocks. This will allow the
Z (CPU) clock driver to request changing the PLL clock rate.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-7-geert+renesas@glider.be
|
|
Improve accuracy in the .determine_rate() callback for Z and Z2 clocks
by using rounded divisions. This is similar to the calculation of rates
and multipliers in the .recalc_rate() resp. set_rate() callbacks.
Sample impact for a few requested clock rates:
- R-Car H3:
- Z 500 MHz: 468 MHz => 515 MHz
- Z2 1000 MHz: 973 MHz => 1011 MHz
- R-Car M3-W:
- Z 500 MHz: 422 MHz => 516 MHz
- Z2 800 MHz: 750 MHz => 788 MHz
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-6-geert+renesas@glider.be
|
|
Fix grammar in comments for cpg_z_clk_set_rate().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-5-geert+renesas@glider.be
|
|
Due to the clamping of mult, "(32 - mult) << __ffs(zclk->mask)" can
never exceed the mask.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-4-geert+renesas@glider.be
|
|
cpg_z_clk.mask contains a mask for a 32-bit register.
Hence its size can be reduced from unsigned long to u32.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-3-geert+renesas@glider.be
|
|
The fixed divider in the calculation of the Z and Z2 clock rates was
generalized from a hardcoded value of two to a parameterized value, but
the comments were not updated accordingly.
Fixes: 20cc05ba04a93f05 ("clk: renesas: rcar-gen3: Parameterise Z and Z2 clock fixed divisor")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210326120100.1577596-2-geert+renesas@glider.be
|
|
commit 6579c8d97ad7 ("clk: Mark fwnodes when their clock provider is added")
revealed that clk/bcm/clk-raspberrypi.c driver calls
devm_of_clk_add_hw_provider(), with a NULL dev->of_node, which resulted in a
NULL pointer dereference in of_clk_add_hw_provider() when calling
fwnode_dev_initialized().
Returning 0 is reducing the if conditions in driver code and is being
consistent with the CONFIG_OF=n inline stub that returns 0 when CONFIG_OF
is disabled. The downside is that drivers will maybe register clkdev lookups
when they don't need to and waste some memory.
Fixes: 6579c8d97ad7 ("clk: Mark fwnodes when their clock provider is added")
Fixes: 3c9ea42802a1 ("clk: Mark fwnodes when their clock provider is added/removed")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210426065618.588144-1-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Release OF node when pci_scan_device() fails (Dmitry Baryshkov)
- Add pci_disable_parity() (Bjorn Helgaas)
- Disable Mellanox Tavor parity reporting (Heiner Kallweit)
- Disable N2100 r8169 parity reporting (Heiner Kallweit)
- Fix RCiEP device to RCEC association (Qiuxu Zhuo)
- Convert sysfs "config", "rom", "reset", "label", "index",
"acpi_index" to static attributes to help fix races in device
enumeration (Krzysztof Wilczyński)
- Convert sysfs "vpd" to static attribute (Heiner Kallweit, Krzysztof
Wilczyński)
- Use sysfs_emit() in "show" functions (Krzysztof Wilczyński)
- Remove unused alloc_pci_root_info() return value (Krzysztof
Wilczyński)
PCI device hotplug:
- Fix acpiphp reference count leak (Feilong Lin)
Power management:
- Fix acpi_pci_set_power_state() debug message (Rafael J. Wysocki)
- Fix runtime PM imbalance (Dinghao Liu)
Virtualization:
- Increase delay after FLR to work around Intel DC P4510 NVMe erratum
(Raphael Norwitz)
MSI:
- Convert rcar, tegra, xilinx to MSI domains (Marc Zyngier)
- For rcar, xilinx, use controller address as MSI doorbell (Marc
Zyngier)
- Remove unused hv msi_controller struct (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller altogether (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc
Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains
(Marc Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
VPD:
- Remove obsolete Broadcom NIC VPD length-limiting quirk (Heiner
Kallweit)
- Remove sysfs VPD size checking dead code (Heiner Kallweit)
- Convert VPF sysfs file to static attribute (Heiner Kallweit)
- Remove unnecessary pci_set_vpd_size() (Heiner Kallweit)
- Tone down "missing VPD" message (Heiner Kallweit)
Endpoint framework:
- Fix NULL pointer dereference when epc_features not implemented
(Shradha Todi)
- Add missing destroy_workqueue() in endpoint test (Yang Yingliang)
Amazon Annapurna Labs PCIe controller driver:
- Fix compile testing without CONFIG_PCI_ECAM (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
APM X-Gene PCIe controller driver:
- Fix cfg resource mapping regression (Dejin Zheng)
Broadcom iProc PCIe controller driver:
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali
Rohár)
Broadcom STB PCIe controller driver:
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim
Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of
deassert/assert (Jim Quinlan)
- Fix brcm_pcie_probe() error return for unsupported revision (Wei
Yongjun)
Cavium ThunderX PCIe controller driver:
- Fix compile testing (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
Freescale Layerscape PCIe controller driver:
- Fix ls_pcie_ep_probe() syntax error (comma for semicolon)
(Krzysztof Wilczyński)
- Remove layerscape-gen4 dependencies on OF and ARM64, add dependency
on ARCH_LAYERSCAPE (Geert Uytterhoeven)
HiSilicon HIP PCIe controller driver:
- Remove obsolete HiSilicon PCIe DT description (Dongdong Liu)
Intel Gateway PCIe controller driver:
- Remove unused pcie_app_rd() (Jiapeng Chong)
Intel VMD host bridge driver:
- Program IRTE with Requester ID of VMD endpoint, not child device
(Jon Derrick)
- Disable VMD MSI-X remapping when possible so children can use more
MSI-X vectors (Jon Derrick)
MediaTek PCIe controller driver:
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
Microchip PolarFlare PCIe controller driver:
- Make several symbols static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Add MCFG quirks for Tegra194 ECAM errata (Vidya Sagar)
- Make several symbols const (Rikard Falkeborn)
- Fix Kconfig host/endpoint typo (Wesley Sheng)
SiFive FU740 PCIe controller driver:
- Add pcie_aux clock to prci driver (Greentime Hu)
- Use reset-simple in prci driver for PCIe (Greentime Hu)
- Add SiFive FU740 PCIe host controller driver and DT binding (Paul
Walmsley, Greentime Hu)
Synopsys DesignWare PCIe controller driver:
- Move MSI Receiver init to dw_pcie_host_init() so it is
re-initialized along with the RC in resume (Jisheng Zhang)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
TI J721E PCIe driver:
- Add DT binding and TI j721e support for refclk to PCIe connector
(Kishon Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon
Vijay Abraham I)
TI Keystone PCIe controller driver:
- Use generic config accessors for TI AM65x (K3) to fix regression
(Kishon Vijay Abraham I)
Xilinx NWL PCIe controller driver:
- Add support for coherent PCIe DMA traffic using CCI (Bharat Kumar
Gogada)
- Add optional "dma-coherent" DT property (Bharat Kumar Gogada)
Miscellaneous:
- Fix kernel-doc warnings (Krzysztof Wilczyński)
- Remove unused MicroGate SyncLink device IDs (Jiri Slaby)
- Remove redundant dev_err() for devm_ioremap_resource() failure
(Chen Hui)
- Remove redundant initialization (Colin Ian King)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)"
* tag 'pci-v5.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (98 commits)
riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC
PCI: fu740: Add SiFive FU740 PCIe host controller driver
dt-bindings: PCI: Add SiFive FU740 PCIe host controller
MAINTAINERS: Add maintainers for SiFive FU740 PCIe driver
clk: sifive: Use reset-simple in prci driver for PCIe driver
clk: sifive: Add pcie_aux clock in prci driver for PCIe driver
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
PCI: Allow VPD access for QLogic ISP2722
PCI/VPD: Add helper pci_get_func0_dev()
PCI/VPD: Remove pci_vpd_find_tag() SRDT handling
PCI/VPD: Remove pci_vpd_find_tag() 'offset' argument
PCI/VPD: Change pci_vpd_init() return type to void
PCI/VPD: Make missing VPD message less alarming
PCI/VPD: Remove pci_set_vpd_size()
x86/PCI: Remove unused alloc_pci_root_info() return value
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
...
|
|
We use reset-simple in this patch so that pcie driver can use
devm_reset_control_get() to get this reset data structure and use
reset_control_deassert() to deassert pcie_power_up_rst_n.
Link: https://lore.kernel.org/r/20210504105940.100004-3-greentime.hu@sifive.com
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
|
|
We add pcie_aux clock in this patch so that pcie driver can use
clk_prepare_enable() and clk_disable_unprepare() to enable and disable
pcie_aux clock.
Link: https://lore.kernel.org/r/20210504105940.100004-2-greentime.hu@sifive.com
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Here's a collection of largely clk driver updates. The usual suspects
are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and Rockchip,
but it feels pretty light on commits.
There's only one real commit to the framework core and that's to
consolidate code. Otherwise the diffstat is dominated by many Qualcomm
clk driver patches that modernize the driver for the proper way of
speciying clk parents. That's shifting data around, which could subtly
break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on
Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (82 commits)
MAINTAINERS: add MT7621 CLOCK maintainer
staging: mt7621-dts: use valid vendor 'mediatek' instead of invalid 'mtk'
staging: mt7621-dts: make use of new 'mt7621-clk'
clk: ralink: add clock driver for mt7621 SoC
clk: uniphier: Fix potential infinite loop
clk: qcom: rpmh: add support for SDX55 rpmh IPA clock
clk: qcom: gcc-sdm845: get rid of the test clock
clk: qcom: convert SDM845 Global Clock Controller to parent_data
dt-bindings: clock: separate SDM845 GCC clock bindings
clk: qcom: apss-ipq-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a53-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a7-pll: Add missing MODULE_DEVICE_TABLE
dt: bindings: add mt7621-sysc device tree binding documentation
dt-bindings: clock: add dt binding header for mt7621 clocks
clk: samsung: Remove redundant dev_err calls
clk: zynqmp: pll: add set_pll_mode to check condition in zynqmp_pll_enable
clk: zynqmp: move zynqmp_pll_set_mode out of round_rate callback
clk: zynqmp: Drop dependency on ARCH_ZYNQMP
clk: zynqmp: Enable the driver if ZYNQMP_FIRMWARE is selected
clk: qcom: gcc-sm8350: use ARRAY_SIZE instead of specifying num_parents
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
|
|
Pull drm updates from Dave Airlie:
"The usual lots of work all over the place.
i915 has gotten some Alderlake work and prelim DG1 code, along with a
major locking rework over the GEM code, and brings back the property
of timing out long running jobs using a watchdog. amdgpu has some
Alderbran support (new GPU), freesync HDMI support along with a lot
other fixes.
Outside of the drm, there is a new printf specifier added which should
have all the correct acks/sobs:
- printk fourcc modifier support added %p4cc
Summary:
core:
- drm_crtc_commit_wait
- atomic plane state helpers reworked for full state
- dma-buf heaps API rework
- edid: rework and improvements for displayid
dp-mst:
- better topology logging
bridge:
- Chipone ICN6211
- Lontium LT8912B
- anx7625 regulator support
panel:
- fix lt9611 4k panels handling
simple-kms:
- add plane state helpers
ttm:
- debugfs support
- removal of unused sysfs
- ignore signaled moved fences
- ioremap buffer according to mem caching
i915:
- Alderlake S enablement
- Conversion to dma_resv_locking
- Bring back watchdog timeout support
- legacy ioctl cleanups
- add GEM TDDO and RFC process
- DG1 LMEM preparation work
- intel_display.c refactoring
- Gen9/TGL PCH combination support
- eDP MSO Support
- multiple PSR instance support
- Link training debug updates
- Disable PSR2 support on JSL/EHL
- DDR5/LPDDR5 support for bw calcs
- LSPCON limited to gen9/10 platforms
- HSW/BDW async flip/VTd corruption workaround
- SAGV watermark fixes
- SNB hard hang on ring resume fix
- Limit imported dma-buf size
- move to use new tasklet API
- refactor KBL/TGL/ADL-S display/gt steppings
- refactoring legacy DP/HDMI, FB plane code out
amdgpu:
- uapi: add ioctl to query video capabilities
- Iniital AMD Freesync HDMI support
- Initial Adebaran support
- 10bpc dithering improvements
- DCN secure display support
- Drop legacy IO BAR requirements
- PCIE/S0ix/RAS/Prime/Reset fixes
- Display ASSR support
- SMU gfx busy queues for RV/PCO
- Initial LTTPR display work
amdkfd:
- MMU notifier fixes
- APU fixes
radeon:
- debugfs cleanps
- fw error handling ifix
- Flexible array cleanups
msm:
- big DSI phy/pll cleanup
- sc7280 initial support
- commong bandwidth scaling path
- shrinker locking contention fixes
- unpin/swap support for GEM objcets
ast:
- cursor plane handling reworked
tegra:
- don't register DP AUX channels before connectors
zynqmp:
- fix OOB struct padding memset
gma500:
- drop ttm and medfield support
exynos:
- request_irq cleanup function
mediatek:
- fine tune line time for EOTp
- MT8192 dpi support
- atomic crtc config updates
- don't support HDMI connector creation
mxsdb:
- imx8mm support
panfrost:
- MMU IRQ handling rework
qxl:
- locking fixes
- resource deallocation changes
sun4i:
- add alpha properties to UI/VI layers
vc4:
- RPi4 CEC support
vmwgfx:
- doc cleanups
arc:
- moved to drm/tiny"
* tag 'drm-next-2021-04-28' of git://anongit.freedesktop.org/drm/drm: (1390 commits)
drm/ttm: Don't count pages in SG BOs against pages_limit
drm/ttm: fix return value check
drm/bridge: lt8912b: fix incorrect handling of of_* return values
drm: bridge: fix LONTIUM use of mipi_dsi_() functions
drm: bridge: fix ANX7625 use of mipi_dsi_() functions
drm/amdgpu: page retire over debugfs mechanism
drm/radeon: Fix a missing check bug in radeon_dp_mst_detect()
drm/amd/display: Fix the Wunused-function warning
drm/radeon/r600: Fix variables that are not used after assignment
drm/amdgpu/smu7: fix CAC setting on TOPAZ
drm/amd/display: Update DCN302 SR Exit Latency
drm/amdgpu: enable ras eeprom on aldebaran
drm/amdgpu: RAS harvest on driver load
drm/amdgpu: add ras aldebaran ras eeprom driver
drm/amd/pm: increase time out value when sending msg to SMU
drm/amdgpu: add DMUB outbox event IRQ source define/complete/debug flag
drm/amd/pm: add the callback to get vbios bootup values for vangogh
drm/radeon: Fix size overflow
drm/amdgpu: Fix size overflow
drm/amdgpu: move mmhub ras_func init to ip specific file
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- addition of a maintainer's profile for the media subsystem
- addition of i.MX8 IP support
- qcom/camss gained support for hardware version Titan 170
- new RC keymaps
- Lots of other improvements, cleanups and bug fixes
* tag 'media/v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (488 commits)
media: coda: fix macroblocks count control usage
media: rkisp1: params: fix wrong bits settings
media: cedrus: Fix H265 status definitions
media: meson-ge2d: fix rotation parameters
media: v4l2-ctrls: fix reference to freed memory
media: venus : hfi: add venus image info into smem
media: venus: Fix internal buffer size calculations for v6.
media: venus: helpers: keep max bandwidth when mbps exceeds the supported range
media: venus: fix hw overload error log condition
media: venus: core: correct firmware name for sm8250
media: venus: core,pm: fix potential infinite loop
media: venus: core: Fix kerneldoc warnings
media: gscpa/stv06xx: fix memory leak
media: cx25821: remove unused including <linux/version.h>
media: staging: media/meson: remove redundant dev_err call
media: adv7842: support 1 block EDIDs, fix clearing EDID
media: adv7842: configure all pads
media: allegro: change kernel-doc comment blocks to normal comments
media: camss: ispif: Remove redundant dev_err call in msm_ispif_subdev_init()
media: i2c: rdamc21: Fix warning on u8 cast
...
|
|
- Proper clk driver for Mediatek MT7621 SoCs
* clk-ralink:
MAINTAINERS: add MT7621 CLOCK maintainer
staging: mt7621-dts: use valid vendor 'mediatek' instead of invalid 'mtk'
staging: mt7621-dts: make use of new 'mt7621-clk'
clk: ralink: add clock driver for mt7621 SoC
dt: bindings: add mt7621-sysc device tree binding documentation
dt-bindings: clock: add dt binding header for mt7621 clocks
|
|
'clk-uniphier' into clk-next
- Simplify Zynq Kconfig dependencies
* clk-imx:
clk: imx: Reference preceded by free
clk: imx8mq: Correct the pcie1 sels
clk: imx8mp: Remove the none exist pcie clocks
clk: imx: Fix reparenting of UARTs not associated with stdout
* clk-samsung:
clk: samsung: Remove redundant dev_err calls
clk: exynos7: Mark aclk_fsys1_200 as critical
* clk-zynq:
clk: zynqmp: pll: add set_pll_mode to check condition in zynqmp_pll_enable
clk: zynqmp: move zynqmp_pll_set_mode out of round_rate callback
clk: zynqmp: Drop dependency on ARCH_ZYNQMP
clk: zynqmp: Enable the driver if ZYNQMP_FIRMWARE is selected
* clk-rockchip:
clk: rockchip: drop MODULE_ALIAS from rk3399 clock controller
clk: rockchip: drop parenthesis from ARM || COMPILE_TEST depends
clk: rockchip: add clock controller for rk3568
clk: rockchip: support more core div setting
dt-binding: clock: Document rockchip, rk3568-cru bindings
clk: rockchip: add dt-binding header for rk3568
* clk-uniphier:
clk: uniphier: Fix potential infinite loop
|
|
and 'clk-qcom' into clk-next
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
* clk-cleanup:
clk: Drop double "if" in clk_core_determine_round_nolock() comment
clk: at91: Trivial typo fixes in the file sama7g5.c
clk: use clk_core_enable_lock() a bit more
* clk-renesas:
clk: renesas: Zero init clk_init_data
clk: renesas: Couple of spelling fixes
clk: renesas: r8a779a0: Add CMT clocks
clk: renesas: r8a7795: Add TMU clocks
clk: renesas: r8a779a0: Add TSC clock
clk: renesas: r8a779a0: Add TMU clocks
clk: renesas: r8a77965: Add DAB clock
clk: renesas: r8a77990: Add DAB clock
* clk-socfpga:
clk: socfpga: remove redundant initialization of variable div
clk: socfpga: arria10: Fix memory leak of socfpga_clk on error return
clk: socfpga: Fix code formatting
clk: socfpga: Convert to s10/agilex/n5x to use clk_hw
clk: socfpga: arria10: convert to use clk_hw
clk: socfpga: use clk_hw_register for a5/c5
* clk-allwinner:
clk: sunxi: Demote non-conformant kernel-doc headers
clk: sunxi-ng: v3s: use sigma-delta modulation for audio-pll
* clk-qcom: (45 commits)
clk: qcom: rpmh: add support for SDX55 rpmh IPA clock
clk: qcom: gcc-sdm845: get rid of the test clock
clk: qcom: convert SDM845 Global Clock Controller to parent_data
dt-bindings: clock: separate SDM845 GCC clock bindings
clk: qcom: apss-ipq-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a53-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a7-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: gcc-sm8350: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: gcc-sm8250: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: gcc-sm8150: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: gcc-sc8180x: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: gcc-sc7180: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: videocc-sm8250: use parent_hws where possible
clk: qcom: videocc-sm8150: use parent_hws where possible
clk: qcom: gpucc-sm8250: use parent_hws where possible
clk: qcom: gpucc-sm8150: use parent_hws where possible
clk: qcom: gcc-sm8350: use parent_hws where possible
clk: qcom: gcc-sm8250: use parent_hws where possible
clk: qcom: gcc-sm8150: use parent_hws where possible
clk: qcom: gcc-sdx55: use parent_hws where possible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"Almost all SoC code changes this time are for the TI OMAP platform,
which continues its decade-long quest to move from describing a
complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer and some
platforms have minor bugfixes and cleanups that were not urgent enough
for v5.12"
* tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
MAINTAINERS: Update ARM/UniPhier SoCs maintainers and status
mailmap: Update email address for Nicolas Saenz
MAINTAINERS: Update BCM2711/BCM2335 maintainer's mail
ARM: exynos: correct kernel doc in platsmp
ARM: hisi: use the correct HiSilicon copyright
ARM: ux500: make ux500_cpu_die static
ARM: s3c: Use pwm_get() in favour of pwm_request() in RX1950
ARM: OMAP1: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: Use DEFINE_SPINLOCK() for spinlock
ARM: at91: pm: Move prototypes to mutually included header
ARM: OMAP2+: use true and false for bool variable
ARM: OMAP2+: add missing call to of_node_put()
ARM: OMAP2+: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
ARM: imx: Kconfig: Fix typo in help
ARM: mach-imx: Fix a spelling in the file pm-imx5.c
bus: ti-sysc: Warn about old dtb for dra7 and omap4/5
ARM: OMAP2+: Stop building legacy code for dra7 and omap4/5
ARM: OMAP2+: Drop legacy platform data for omap5 hwmod
ARM: OMAP2+: Drop legacy platform data for omap5 l3
...
|
|
* pm-cpufreq: (22 commits)
cpufreq: Kconfig: fix documentation links
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpufreq: Remove unused for_each_policy macro
cpufreq: dt: dev_pm_opp_of_cpumask_add_table() may return -EPROBE_DEFER
cpufreq: intel_pstate: Clean up frequency computations
cpufreq: cppc: simplify default delay_us setting
cpufreq: Rudimentary typos fix in the file s5pv210-cpufreq.c
cpufreq: CPPC: Add support for frequency invariance
ia64: fix format string for ia64-acpi-cpu-freq
cpufreq: schedutil: Call sugov_update_next_freq() before check to fast_switch_enabled
arch_topology: Export arch_freq_scale and helpers
...
|
|
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ROHM BD71815 also provide clk signal for RTC. Add control
for gating this clock.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
msm-next from Rob:
* Big DSI phy/pll cleanup. Includes some clk patches, acked by
maintainer
* Initial support for sc7280
* compatibles fixes for sm8150/sm8250
* cleanups for all dpu gens to use same bandwidth scaling paths (\o/)
* various shrinker path lock contention optimizations
* unpin/swap support for GEM objects (disabled by default, enable with
msm.enable_eviction=1 .. due to various combinations of iommu drivers
with older gens I want to get more testing on hw I don't have in front
of me before enabling by default)
* The usual assortment of misc fixes and cleanups
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvL=4aw15qoY8fbKG9FCgnx8Y-dCtf7xiFwTQSHopwSQg@mail.gmail.com
|
