| Age | Commit message (Collapse) | Author |
|---|
|
On the H6, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
This patch adds the post-dividers to the MMC clocks, following the
approach on A64.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On R-Car V3M (AKA R8A77970), the SD0CKCR is laid out differently than on
the other R-Car gen3 SoCs. In fact, the layout is the same as on R-Car gen2
SoCs, so we'll need to copy the divisor tables from the R-Car gen2 driver.
We'll also need to support the SoC specific clock types, thus we're adding
CLK_TYPE_GEN3_SOC_BASE at the end of 'enum rcar_gen3_clk_types', declare
SD0H/SDH clocks in 'enum r8a77970_clk_types', and handle those clocks in
the overridden cpg_clk_register() method; then, finally, add the SD-IF
module clock (derived from the SD0 clock).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Now that RCLK has been added by Geert, we can add the CMT module clocks.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add suspend/resume hooks in Armada 37xx peripheral clocks driver to
handle S2RAM operations.
One can think that these hooks are useless by comparing the register
values before and after a suspend/resume cycle: they will look the same
anyway. This is because of some scripts executed by the Cortex-M3 core
during ATF operations to init both the clocks and the DDR. These values
could be modified by the BL33 stage or by Linux itself and should be
preserved.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Prepare the introduction of suspend/resume hooks by having an easy way
to access all the registers in one go just from a device: add the IP
base address in the driver data.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.
Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.
This code was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Fixes: 97b7129cd2af ("reset: hisilicon: change the definition of hisi_reset_init")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When trying to use I2C7 on R-Car E3:
renesas-cpg-mssr e6150000.clock-controller: Cannot get module clock 1003: -2
i2c-rcar e6690000.i2c: failed to add to PM domain always-on: -2
i2c-rcar: probe of e6690000.i2c failed with error -2
Unlike other R-Car Gen3 SoCs, R-Car E3 has more than 7 I2C bus
interfaces. Add the forgotten module clock for the 8th instance to fix
this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add and correct PLL rates for better hdmi output.
This includes minimizing jitter on 213 MHz for better 71 MHz,
250.5 MHz for better 83.5 MHz, 428 MHz for better 25.175 Mhz,
low jitter 273 MHz for better 68.25 mhz, 356 MHz for better 118.68 Mhz
and 300MHz.
Increase the used Fvco for 308, 324 MHz, 292.5 MHz, 273.6 MHz,
238 MHz and 216 MHz.
And add some additional rates allowing to reach better hdmi-related
rates in general.
These match the rates used by ChromeOS, so have been quite widely tested.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Array audio_parents is declared but never used, hence it is redundant
and can be removed.
Cleans up clang warning:
warning: 'audio_parents' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for the camera clock controller found on SDM845
based devices. This would allow camera drivers to probe and
control their clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
of_get_child_by_name() returns device node with refcount incremented,
but there is no decrement in cdce925_probe(). The patch adds one.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The table allocated in clk_rcg2_dfs_populate_freq_table() is
eventually iterated over by qcom_find_freq() which assumes that the
table is NULL terminated. Allocate one extra space in the array for
the NULL termination. Initting of the NULL termination is implicit
due to kcalloc().
Fixes: cc4f6944d0e3 ("clk: qcom: Add support for RCG to register for DFS")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
System clk provided in ST soc can be set to:
48Mhz, non-spread
25Mhz, spread
To get accurate rate, we need it to set it at non-spread
option which is 48Mhz.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Fixes: 421bf6a1f061 ("clk: x86: Add ST oscout platform clock")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.
Also fix the related node-reference leaks.
Fixes: 5b385a45e001 ("clk: ti: add support for clkctrl aliases")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add both the interface and core clock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add a few missing gcc clks for msm8996
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: omit aggre0_noc_qosgen_extref_clk]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count,
GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, currently, there is a bug during the allocation:
sizeof(npcm7xx_clk_data) should be sizeof(*npcm7xx_clk_data)
Fix this bug by using struct_size() in kzalloc()
This issue was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch adds FDP1-0 clock to the R8A77965 SoC.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The clock IDs must match between DeviceTree bindings and the driver.
There is already a header file used by DeviceTree sources so include it
in the driver to remove duplicated symbols.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
QUPv3 clocks support DFS and thus register the RCGs which require support
for the same.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Use new macro, split out init structures so they
don't have to be copied]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Dynamic Frequency switch is a feature of clock controller by which request
from peripherals allows automatic switching frequency of input clock
without SW intervention. There are various performance levels associated
with a root clock. When the input performance state changes, the source
clocks and division ratios of the new performance state are loaded on to
RCG via HW and the RCG switches to new clock frequency when the RCG is in
DFS HW enabled mode.
Register the root clock generators(RCG) to switch to use the dfs clock ops
in the cases where DFS is enabled. The clk_round_rate() called by the clock
consumer would invoke the dfs determine clock ops and would read the DFS
performance level registers to identify all the frequencies supported and
update the frequency table. The DFS clock consumers would maintain these
frequency mapping and request the desired performance levels.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Rework registration logic to stop copying, change
recalc_rate() to index directly into the table if possible and fallback
to calculating on the fly with an assumed correct parent]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add RZ/G2M (R8A774A1) Clock Pulse Generator / Module Standby and Software
Reset support.
Based on the Table 8.2b of "RZ/G Series, 2nd Generation User's Manual:
Hardware ((Rev. 0.61, June 12, 2018)".
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds SATA clock to the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
On R-Car V3H, RCLK can be switched between EXTALR and the On-Chip
Oscillator using mode pin MD19.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Make the existing support for selecting between clean and SSCG clocks
using MD12 more generic, to allow using other mode pins for arbitrary
clock selection.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car D3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car E3 has the
RCLK Frequency Control Register (RCKCR), which determines the OSC and
RINT predivider values, and selection of the RCLK clock source between
RINT and the On-Chip Oscillator.
Hence change the OSC and RINT clock definitions to use the RCKCR
divider, and add the missing On-Chip Oscillator and RCLK clock source
switching logic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a clock type and macro for defining clocks where the parent and
divider are selected based on the value of the RCKCR.CKSEL bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for defining fixed rate clocks, to be used for on-chip
oscillators.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car Gen3 Hardware Manual Rev.0.54 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC clock. Hence augment the configuration structure with all
documented predivider values.
Add the OSC clock using the configured predivider.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.1.00, R-Car M3-N does not
have the CPG_RCKCR register. Change the OSC and RINT clock definitions
to use the OSC EXTAL predivider instead, which is supported on all R-Car
M3-N SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car M3-W ES1.1. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car M3-W SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
R-Car Gen3 Hardware Manual Rev.0.52 documents the relation between the
MD13 and MD14 mode pins, and the OSC EXTAL predivider, as used by the
OSC and RINT RCLK clocks. Hence augment the configuration structure
with all documented predivider values.
According to R-Car Gen3 Hardware Manual Rev.0.53, the CPG_RCKCR
register was removed in R-Car H3 ES2.0. Change the OSC and RINT
clock definitions to use the OSC EXTAL predivider instead, which is
supported on all R-Car H3 SoC revisions.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a clock type and macro for defining clocks using the OSC EXTAL
predivider combined with a fixed divider.
On most R-Car Gen3 SoCs, the predivider value depends on mode pins, and
thus must be specified in the configuration structure.
Inspired by a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
All other internal clock names have a period prepended.
Hence rename the internal RCLK from "rint" to ".r", and move it to the
section where all other internal clocks are defined.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
It may happen that clock framework finds optimal video PLL rate above
that which is really supported by HW.
User manual doesn't really say what is upper limit for video PLLs on
A83T. Because of that, use the maximum rate defined in BSP clk driver
which is 3 GHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Some, if not most, NKMP PLLs can be set to higher rate that is really
supported by HW.
Implement support for maximum frequency constrain for NKMP PLLs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Video PLLs on R40 can be set to higher rate that it is actually
supported by HW.
Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
As it turns out, pll-video can be set to higher rate that it is really
supported by HW.
For example, one monitor requested 185.58 MHz pixel clock. Clock
framework calculated that minimum rate error would be when pll-video
is set to 2040 MHz. This is clearly out of specs.
Both H3 and H5 user manuals specify 600 MHz as maximum supported rate.
However, BSP clock drivers allow up to 912 MHz and 1008 MHz
respectively. Here 912 MHz is chosen because user manuals were already
proven wrong once for lower limits.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On some NM PLLs, frequency can be set above PLL working range.
Add a constraint for maximum supported rate. This way, drivers can
specify which is maximum allowed rate for PLL.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Currently the register offset of the PWM bus gate in Allwinner H6 clock
driver is wrong.
Fix this issue.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Rongyi Chen <chenyi@tt-cool.com>
[Icenowy: refactor commit message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The bus clocks (AHB/APB) on Allwinner H6 have their second divider start
at bit 8, according to the user manual and the BSP code. However,
currently the divider offset is incorrectly set to 16, thus the divider
is not correctly read and the clock frequency is not correctly calculated.
Fix this bit offset on all affected bus clocks in ccu-sun50i-h6.
Cc: stable@vger.kernel.org # v4.17.y
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 32-bit SoC platform updates from Olof Johansson:
"Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
ARM: uniphier: select RESET_CONTROLLER
arm64: uniphier: select RESET_CONTROLLER
ARM: uniphier: remove empty Makefile
ARM: exynos: Clear global variable on init error path
ARM: exynos: Remove outdated maintainer information
ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
soc: r9a06g032: don't build SMP files for non-SMP config
ARM: shmobile: Add the R9A06G032 SMP enabler driver
ARM: at91: pm: configure wakeup sources for ULP1 mode
ARM: at91: pm: add PMC fast startup registers defines
ARM: at91: pm: Add ULP1 mode support
ARM: at91: pm: Use ULP0 naming instead of slow clock
ARM: hisi: handle of_iomap and fix missing of_node_put
ARM: hisi: check of_iomap and fix missing of_node_put
ARM: hisi: fix error handling and missing of_node_put
ARM: mx5: Set the DBGEN bit in ARM_GPC register
ARM: imx51: Configure M4IF to avoid visual artifacts
ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
ARM: imx: fix i.MX6SLL build
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The new and exciting feature this time around is in the clk core.
We've added duty cycle support to the clk API so that clk signal duty
cycle ratios can be adjusted while taking into account things like clk
dividers and clk tree hierarchy. So far only one SoC has implemented
support for this, but I expect there will be more to come in the
future.
Outside of the core, we have the usual pile of clk driver updates and
additions. The Amlogic meson driver got the most lines in the diffstat
this time around because it added support for a whole bunch of
hardware and duty cycle configuration. After that the Rockchip PX30,
Qualcomm SDM845, and Renesas SoC drivers fill in a majority of the
diff. We're left with the collection of non-critical fixes after that.
Overall it looks pretty quiet this time.
Core:
- Clk duty cycle support
- Proper CLK_SET_RATE_GATE support throughout the tree
New Drivers:
- Actions Semi Owl series S700 SoC clk driver
- Qualcomm SDM845 display clock controller
- i.MX6SX ocram_s clk support
- Uniphier NAND, USB3 PHY, and SPI clk support
- Qualcomm RPMh clk driver
- i.MX7D mailbox clk support
- Maxim 9485 Programmable Clock Generator
- expose 32 kHz PLL on PXA SoCs
- imx6sll GPIO clk gate support
- Atmel at91 I2S audio clk support
- SI544/SI514 clk on/off support
- i.MX6UL GPIO clock gates in CCM CCGR
- Renesas Crypto Engine clocks on R-Car H3
- Renesas clk support for the new RZ/N1D SoC
- Allwinner A64 display engine clock support
- support for Rockchip's PX30 SoC
- Amlogic Meson axg PCIe and audio clocks
- Amlogic Meson GEN CLK on gxbb, gxl and axg
Updates:
- remove an unused variable from Exynos4412 ISP driver
- fix a thinko bug in SCMI clk division logic
- add missing of_node_put()s in some i.MX clk drivers
- Tegra SDMMC clk jitter improvements with high speed signaling modes
- SPDX tagging for qcom and cs2000-cp drivers
- stop leaking con ids in __clk_put()
- fix a corner case in fixed factor clk probing where node is in DT
but parent clk is registered much later
- Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return
value
- i.MX clk init arrays removed in place of CLK_IS_CRITICAL
- convert to CLK_IS_CRITICAL for i.MX51/53 driver
- fix Tegra BPMP driver oops when xlating a NULL clk
- proper default configuration for vic03 and vde clks on Tegra124
- mark Tegra memory controller clks as critical
- fix array bounds clamp in Tegra's emc determine_rate() op
- Ingenic i2s bit update and allow UDC clk to gate
- fix name of aspeed SDC clk define to have only one 'CLK'
- fix i.MX6QDL video clk parent
- critical clk markings for qcom SDM845
- fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
- mark Rockchip's pclk_rkpwm_pmu as critical clock, due to it
supplying the pwm used to drive the logic supply of the rk3399
core"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (85 commits)
clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
clk: cs2000-cp: convert to SPDX identifiers
clk: scmi: Fix the rounding of clock rate
clk: qcom: Add display clock controller driver for SDM845
clk: mvebu: armada-37xx-periph: Remove unused var num_parents
clk: samsung: Remove unused mout_user_aclk400_mcuisp_p4x12 variable
clk: actions: Add S700 SoC clock support
dt-bindings: clock: Add S700 support for Actions Semi Soc's
clk: actions: Add missing REGMAP_MMIO dependency
clk: uniphier: add clock frequency support for SPI
clk: uniphier: add more USB3 PHY clocks
clk: uniphier: add NAND 200MHz clock
clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks
clk: tegra: Add sdmmc mux divider clock
clk: tegra: Refactor fractional divider calculation
clk: tegra: Fix includes required by fence_udelay()
clk: imx6sll: fix missing of_node_put()
clk: imx6ul: fix missing of_node_put()
clk: imx: add ocram_s clock for i.mx6sx
clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
...
|
