| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-fixes
Pull Renesas clk driver fixes from Geert Uytterhoeven:
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
* tag 'renesas-clk-fixes-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a779g0: Fix HSCIF parent clocks
clk: renesas: r8a779g0: Add SASYNCPER clocks
|
|
Fix typo pll5_mux_dsi_div_params -> mux_dsi_div_params
Fixes the below warning (make W=1):
drivers/clk/renesas/rzg2l-cpg.c:115: warning: Function parameter or member 'mux_dsi_div_params' not described in 'rzg2l_cpg_priv'
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026012123.159790-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Correct the misspelled textual name of the SD0H clock.
Fixes: 470e3f0d0b15 ("clk: renesas: rcar-gen4: Introduce R-Car Gen4 CPG driver")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221012184830.3199-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the module clock used by the SPI Multi I/O Bus Controller (RPC-IF)
on the Renesas R-Car V4H (R8A779G0) SoC.
While at it, fix table alignment in the definition of the related
RPCSRC internal clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f0609c82e742865be753b67a0a6080f193f405ad.1665583328.git.geert+renesas@glider.be
|
|
Add the SD0H core clock and the SDHI module clock, which are used by the
SD Card/MMC Interface on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/e9b05d102160cc3f7395ac53a533e81c07307d5e.1665558175.git.geert+renesas@glider.be
|
|
Add the SASYNCPER internal clock, which is the clock source of the
various SASYNCPERD[124] clocks, to match the clock tree diagram in the
documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/18e6765bfc3bf7c3ee5ce93a370d377c1d17728e.1665558014.git.geert+renesas@glider.be
|
|
Correct the misspelled textual name of the SD0H clock.
Fixes: 9b5dd1ff705c6854 ("clk: renesas: r8a779f0: Add SDH0 clock")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1f682d338f133608f138ae87323707436ad8c748.1665558014.git.geert+renesas@glider.be
|
|
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231253.15592-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231013.14791-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the module clock used by the 16-Bit Timer Pulse Unit (TPU) on the
Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/f2c1e2c5411b7bd6af726e6baf6e1efc354a7cdf.1665147497.git.geert+renesas@glider.be
|
|
Add the module clock used by the PWM timers on the Renesas R-Car V4H
(R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/a33d0e51c2fe8a0e6c89f3fd92db7c4bf5c33074.1665147497.git.geert+renesas@glider.be
|
|
Add the module clocks used by the Serial Communication Interfaces with
FIFO (SCIF) on the Renesas R-Car V4H (R8A779G0) SoC.
Based on a larger patch in the BSP by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/a6ab466cfdac377106494c00b811a60151cb1825.1665147497.git.geert+renesas@glider.be
|
|
clk: renesas: Fixes for v6.1
- Correct the parent clocks for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) modules on the R-Car V4H SoC.
Note that HSCIF0 is used for the serial console on the White-Hawk
development board.
|
|
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf1834177a2 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
|
|
"div4" DIVs which divide PLLs by 4 are actually dividing "div2" DIVs by
2 to achieve a by 4 division, thus their parents are the respective
"div2" DIVs. These DIVs were mistakenly set to have the PLLs as parents.
This leads to the kernel thinking "div4"s and everything under them run
at 2x the clock speed. Fix this.
Fixes: 45bd8166a1d8 ("clk: samsung: Add initial Exynos7885 clock driver")
Signed-off-by: David Virag <virag.david003@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20221013151341.151208-1-virag.david003@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
|
|
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220913031956.984475-1-yangyingliang@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220913032403.1007902-1-yangyingliang@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Simplify the driver using devm_regulator_get_enable() instead of
open-coding the devm_add_action_or_reset().
A (minor?) functional change is that we don't print an error in case of a
deferred probe. Now we also print the error no matter which of the
involved calls caused the failure.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/1f46b06be44527a93cd0bfd5de2fa8e2899524ab.1660934107.git.mazziesaccount@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This entire Kconfig file is only included within the if COMMON_CLK
section of the drivers/clk/Kconfig file. That makes the depends on
COMMON_CLK here redundant. Remove it.
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20221003203103.2705007-1-sboyd@kernel.org
|
|
One of the clock entry "dcl" clk has some HW limitations. One is that
its rate can only by changed by changing its parent clk's rate & two is
that HW does not support enable/disable for this clk.
Handle above two limitations by adding relevant flags. Add standard flag
CLK_SET_RATE_PARENT to handle rate change and add driver internal flag
DIV_CLK_NO_MASK to handle enable/disable.
Fixes: d058fd9e8984 ("clk: intel: Add CGU clock driver for a new SoC")
Reviewed-by: Yi xin Zhu <yzhu@maxlinear.com>
Signed-off-by: Rahul Tanwar <rtanwar@maxlinear.com>
Link: https://lore.kernel.org/r/a4770e7225f8a0c03c8ab2ba80434a4e8e9afb17.1665642720.git.rtanwar@maxlinear.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In MxL's LGM SoC, gate clocks can be controlled either from CGU clk driver
i.e. this driver or directly from power management driver/daemon. It is
dependent on the power policy/profile requirements of the end product.
To support such use cases, provide option to override gate clks enable/disable
by adding a flag GATE_CLK_HW which controls if these gate clks are controlled
by HW i.e. this driver or overridden in order to allow it to be controlled
by power profiles instead.
Reviewed-by: Yi xin Zhu <yzhu@maxlinear.com>
Signed-off-by: Rahul Tanwar <rtanwar@maxlinear.com>
Link: https://lore.kernel.org/r/bdc9c89317b5d338a6c4f1d49386b696e947a672.1665642720.git.rtanwar@maxlinear.com
[sboyd@kernel.org: Add braces on many line if-else]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Patch 1/4 of this patch series switches from direct readl/writel
based register access to regmap based register access. Instead
of using direct readl/writel, regmap API's are used to read, write
& read-modify-write clk registers. Regmap API's already use their
own spinlocks to serialize the register accesses across multiple
cores in which case additional driver spinlocks becomes redundant.
Hence, remove redundant spinlocks from driver in this patch 2/4.
Reviewed-by: Yi xin Zhu <yzhu@maxlinear.com>
Signed-off-by: Rahul Tanwar <rtanwar@maxlinear.com>
Link: https://lore.kernel.org/r/a8a02c8773b88924503a9fdaacd37dd2e6488bf3.1665642720.git.rtanwar@maxlinear.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Earlier version of driver used direct io remapped register read
writes using readl/writel. But we need secure boot access which
is only possible when registers are read & written using regmap.
This is because the security bus/hook is written & coupled only
with regmap layer.
Switch the driver from direct readl/writel based register accesses
to regmap based register accesses.
Additionally, update the license headers to latest status.
Reviewed-by: Yi xin Zhu <yzhu@maxlinear.com>
Signed-off-by: Rahul Tanwar <rtanwar@maxlinear.com>
Link: https://lore.kernel.org/r/2610331918206e0e3bd18babb39393a558fb34f9.1665642720.git.rtanwar@maxlinear.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
clk_mt8195_topck_probe()
If devm_clk_hw_register_mux() fails in clk_mt8195_topck_probe(), it should return
error code.
Fixes: deeb2af77cf6 ("clk: mediatek: clk-mt8195-topckgen: Register mfg_ck_fast_ref as generic mux")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221009025056.35311-1-yangyingliang@huawei.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
With the aim of dropping direct selects of drivers from Kconfig.socs,
default the SiFive clock drivers to the value of SOC_SIFIVE.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221005171348.167476-2-conor@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add custom I2C accessors to this driver, since the regular I2C regmap ones
do not generate the exact I2C transfers required by the chip. On I2C write,
it is mandatory to send transfer length first, on read the chip returns the
transfer length in first byte. Instead of always reading back 8 bytes, which
is the default and also the size of the entire register file, set BCP register
to 1 to read out 1 byte which is less wasteful.
Fixes: 892e0ddea1aa ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220929195521.284497-1-marex@denx.de
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add MTU3a clock and reset entry to CPG driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20221005111855.553436-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the module clock used by the Interrupt Controller for External
Devices (INTC-EX) aka IRQC on the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8b5ab900ebce8c38604292a5138da11ad2cb072c.1664368268.git.geert+renesas@glider.be
|
|
Add the module clocks used by the Clock-Synchronized Serial Interfaces
with FIFO (MSIOF) on the Renesas R-Car V4H (R8A779G0) SoC.
Extracted from a larger patch in the BSP by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/3cb2f1798145099a46134862c6bcbdcc29ca7410.1664204336.git.geert+renesas@glider.be
|
|
Add the module clocks used by the Direct Memory Access Controllers for
System (SYS-DMAC) on the Renesas R-Car V4H (R8A779G0) SoC.
Extracted from a larger patch in the BSP by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d9f8322d362c7cebb29bfa7e128b4974882c4a7d.1664204336.git.geert+renesas@glider.be
|
|
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220922051358.3442191-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Fix typo, rzg2l_mod_clock__get_sibling -> rzg2l_mod_clock_get_sibling
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220921080051.5604-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently, determine_rate() is not doing any round operation
and due to this it always selects a lower clock source compared
to the closest higher one.
Support sd clk mux round operation by passing
CLK_MUX_ROUND_CLOSEST flag to clk_mux_determine_rate_flags().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220919084110.3065156-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"This is the final part of the clk patches for this merge window.
The clk rate range series needed another week to fully bake. Maxime
fixed the bug that broke clk notifiers and prevented this from being
included in the first pull request. He also added a unit test on top
to make sure it doesn't break so easily again. The majority of the
series fixes up how the clk_set_rate_*() APIs work, particularly
around when the rate constraints are dropped and how they move around
when reparenting clks. Overall it's a much needed improvement to the
clk rate range APIs that used to be pretty broken if you looked
sideways.
Beyond the core changes there are a few driver fixes for a compilation
issue or improper data causing clks to fail to register or have the
wrong parents. These are good to get in before the first -rc so that
the system actually boots on the affected devices"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (31 commits)
clk: tegra: Fix Tegra PWM parent clock
clk: at91: fix the build with binutils 2.27
clk: qcom: gcc-msm8660: Drop hardcoded fixed board clocks
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are three fixes for build warnings that came in during the merge
window"
* tag 'arm-fixes-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: mmp: Make some symbols static
ARM: spear6xx: Staticize few definitions
clk: spear: Move prototype to accessible header
|
|
- Various clk rate range fixes
- Drop clk rate range constraints on clk_put() (redux)
* clk-rate-range: (28 commits)
clk: mediatek: clk-mux: Add .determine_rate() callback
clk: tests: Add tests for notifiers
clk: Update req_rate on __clk_recalc_rates()
clk: tests: Add missing test case for ranges
clk: qcom: clk-rcg2: Take clock boundaries into consideration for gfx3d
clk: Introduce the clk_hw_get_rate_range function
clk: Zero the clk_rate_request structure
clk: Stop forwarding clk_rate_requests to the parent
clk: Constify clk_has_parent()
clk: Introduce clk_core_has_parent()
clk: Switch from __clk_determine_rate to clk_core_round_rate_nolock
clk: Add our request boundaries in clk_core_init_rate_req
clk: Introduce clk_hw_init_rate_request()
clk: Move clk_core_init_rate_req() from clk_core_round_rate_nolock() to its caller
clk: Change clk_core_init_rate_req prototype
clk: Set req_rate on reparenting
clk: Take into account uncached clocks in clk_set_rate_range()
clk: tests: Add some tests for orphan with multiple parents
clk: tests: Add tests for mux with multiple parents
clk: tests: Add tests for single parent mux
...
|
|
Commit 8c193f4714df ("pwm: tegra: Optimize period calculation") updated
the period calculation in the Tegra PWM driver and now returns an error
if the period requested is less than minimum period supported. This is
breaking PWM support on various Tegra platforms. For example, on the
Tegra210 Jetson Nano platform this is breaking the PWM fan support and
probing the PWM fan driver now fails ...
pwm-fan pwm-fan: Failed to configure PWM: -22
pwm-fan: probe of pwm-fan failed with error -22
The problem is that the default parent clock for the PWM on Tegra210 is
a 32kHz clock and is unable to support the requested PWM period.
Fix PWM support on Tegra20, Tegra30, Tegra114, Tegra124 and Tegra210 by
updating the parent clock for the PWM to be the PLL_P.
Fixes: 8c193f4714df ("pwm: tegra: Optimize period calculation")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # TF101 T20
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # TF201 T30
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # TF700T T3
Link: https://lore.kernel.org/r/20221010100046.6477-1-jonathanh@nvidia.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
These two clocks are now registered in the device tree as fixed clocks,
causing a regression in the driver as the clock already exists with
e.g. the name "pxo_board" as the MSM8660 GCC driver probes.
Fix this by just not hard-coding this anymore and everything works
like a charm.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: baecbda52933 ("ARM: dts: qcom: msm8660: fix node names for fixed clocks")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221013140745.7801-1-linus.walleij@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since commit 262ca38f4b6e ("clk: Stop forwarding clk_rate_requests
to the parent"), the clk_rate_request is .. as the title says, not
forwarded anymore to the parent: this produces an issue with the
MediaTek clock MUX driver during GPU DVFS on MT8195, but not on
MT8192 or others.
This is because, differently from others, like MT8192 where all of
the clocks in the MFG parents tree are of mtk_mux type, but in the
parent tree of MT8195's MFG clock, we have one mtk_mux clock and
one (clk framework generic) mux clock, like so:
names: mfg_bg3d -> mfg_ck_fast_ref -> top_mfg_core_tmp (or) mfgpll
types: mtk_gate -> mux -> mtk_mux (or) mtk_pll
To solve this issue and also keep the GPU DVFS clocks code working
as expected, wire up a .determine_rate() callback for the mtk_mux
ops; for that, the standard clk_mux_determine_rate_flags() was used
as it was possible to.
This commit was successfully tested on MT6795 Xperia M5, MT8173 Elm,
MT8192 Spherion and MT8195 Tomato; no regressions were seen.
For the sake of some more documentation about this issue here's the
trace of it:
[ 12.211587] ------------[ cut here ]------------
[ 12.211589] WARNING: CPU: 6 PID: 78 at drivers/clk/clk.c:1462 clk_core_init_rate_req+0x84/0x90
[ 12.211593] Modules linked in: stp crct10dif_ce mtk_adsp_common llc rfkill snd_sof_xtensa_dsp
panfrost(+) sbs_battery cros_ec_lid_angle cros_ec_sensors snd_sof_of
cros_ec_sensors_core hid_multitouch cros_usbpd_logger snd_sof gpu_sched
snd_sof_utils fuse ipv6
[ 12.211614] CPU: 6 PID: 78 Comm: kworker/u16:2 Tainted: G W 6.0.0-next-20221011+ #58
[ 12.211616] Hardware name: Acer Tomato (rev2) board (DT)
[ 12.211617] Workqueue: devfreq_wq devfreq_monitor
[ 12.211620] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 12.211622] pc : clk_core_init_rate_req+0x84/0x90
[ 12.211625] lr : clk_core_forward_rate_req+0xa4/0xe4
[ 12.211627] sp : ffff80000893b8e0
[ 12.211628] x29: ffff80000893b8e0 x28: ffffdddf92f9b000 x27: ffff46a2c0e8bc05
[ 12.211632] x26: ffff46a2c1041200 x25: 0000000000000000 x24: 00000000173eed80
[ 12.211636] x23: ffff80000893b9c0 x22: ffff80000893b940 x21: 0000000000000000
[ 12.211641] x20: ffff46a2c1039f00 x19: ffff46a2c1039f00 x18: 0000000000000000
[ 12.211645] x17: 0000000000000038 x16: 000000000000d904 x15: 0000000000000003
[ 12.211649] x14: ffffdddf9357ce48 x13: ffffdddf935e71c8 x12: 000000000004803c
[ 12.211653] x11: 00000000a867d7ad x10: 00000000a867d7ad x9 : ffffdddf90c28df4
[ 12.211657] x8 : ffffdddf9357a980 x7 : 0000000000000000 x6 : 0000000000000004
[ 12.211661] x5 : ffffffffffffffc8 x4 : 00000000173eed80 x3 : ffff80000893b940
[ 12.211665] x2 : 00000000173eed80 x1 : ffff80000893b940 x0 : 0000000000000000
[ 12.211669] Call trace:
[ 12.211670] clk_core_init_rate_req+0x84/0x90
[ 12.211673] clk_core_round_rate_nolock+0xe8/0x10c
[ 12.211675] clk_mux_determine_rate_flags+0x174/0x1f0
[ 12.211677] clk_mux_determine_rate+0x1c/0x30
[ 12.211680] clk_core_determine_round_nolock+0x74/0x130
[ 12.211682] clk_core_round_rate_nolock+0x58/0x10c
[ 12.211684] clk_core_round_rate_nolock+0xf4/0x10c
[ 12.211686] clk_core_set_rate_nolock+0x194/0x2ac
[ 12.211688] clk_set_rate+0x40/0x94
[ 12.211691] _opp_config_clk_single+0x38/0xa0
[ 12.211693] _set_opp+0x1b0/0x500
[ 12.211695] dev_pm_opp_set_rate+0x120/0x290
[ 12.211697] panfrost_devfreq_target+0x3c/0x50 [panfrost]
[ 12.211705] devfreq_set_target+0x8c/0x2d0
[ 12.211707] devfreq_update_target+0xcc/0xf4
[ 12.211708] devfreq_monitor+0x40/0x1d0
[ 12.211710] process_one_work+0x294/0x664
[ 12.211712] worker_thread+0x7c/0x45c
[ 12.211713] kthread+0x104/0x110
[ 12.211716] ret_from_fork+0x10/0x20
[ 12.211718] irq event stamp: 7102
[ 12.211719] hardirqs last enabled at (7101): [<ffffdddf904ea5a0>] finish_task_switch.isra.0+0xec/0x2f0
[ 12.211723] hardirqs last disabled at (7102): [<ffffdddf91794b74>] el1_dbg+0x24/0x90
[ 12.211726] softirqs last enabled at (6716): [<ffffdddf90410be4>] __do_softirq+0x414/0x588
[ 12.211728] softirqs last disabled at (6507): [<ffffdddf904171d8>] ____do_softirq+0x18/0x24
[ 12.211730] ---[ end trace 0000000000000000 ]---
Fixes: 262ca38f4b6e ("clk: Stop forwarding clk_rate_requests to the parent")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221011135548.318323-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
We're recently encountered a regression due to the rates reported
through the clk_notifier_data being off when changing parents.
Let's add a test suite and a test to make sure that we do get notified
and with the proper rates.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221010-rpi-clk-fixes-again-v1-2-d87ba82ac404@cerno.tech
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Commit cb1b1dd96241 ("clk: Set req_rate on reparenting") introduced a
new function, clk_core_update_orphan_child_rates(), that updates the
req_rate field on reparenting.
It turns out that that function will interfere with the clock notifying
done by __clk_recalc_rates(). This ends up reporting the new rate in
both the old_rate and new_rate fields of struct clk_notifier_data.
Since clk_core_update_orphan_child_rates() is basically
__clk_recalc_rates() without the notifiers, and with the req_rate field
update, we can drop clk_core_update_orphan_child_rates() entirely, and
make __clk_recalc_rates() update req_rate.
However, __clk_recalc_rates() is being called in several code paths:
when retrieving a rate (most likely through clk_get_rate()), when changing
parents (through clk_set_rate() or clk_hw_reparent()), or when updating
the orphan status (through clk_core_reparent_orphans_nolock(), called at
registration).
Updating req_rate on reparenting or initialisation makes sense, but we
shouldn't do it on clk_get_rate(). Thus an extra flag has been added to
update or not req_rate depending on the context.
Fixes: cb1b1dd96241 ("clk: Set req_rate on reparenting")
Link: https://lore.kernel.org/linux-clk/0acc7217-762c-7c0d-45a0-55c384824ce4@samsung.com/
Link: https://lore.kernel.org/linux-clk/Y0QNSx+ZgqKSvPOC@sirena.org.uk/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221010-rpi-clk-fixes-again-v1-1-d87ba82ac404@cerno.tech
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/clk/spear/spear6xx_clock.c:116:13: warning: no previous prototype for function 'spear6xx_clk_init' [-Wmissing-prototypes]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- 'remove' callback converted to return void. Big change with trivial
fixes all over the tree. Other subsystems depending on this change
have been asked to pull an immutable topic branch for this.
- new driver for Microchip PCI1xxxx switch
- heavy refactoring of the Mellanox BlueField driver
- we prefer async probe in the i801 driver now
- the rest is usual driver updates (support for more SoCs, some
refactoring, some feature additions)
* tag 'i2c-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
i2c: pci1xxxx: prevent signed integer overflow
i2c: acpi: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
i2c: i801: Prefer async probe
i2c: designware-pci: Use standard pattern for memory allocation
i2c: designware-pci: Group AMD NAVI quirk parts together
i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch
docs: i2c: slave-interface: return errno when handle I2C_SLAVE_WRITE_REQUESTED
i2c: mlxbf: remove device tree support
i2c: mlxbf: support BlueField-3 SoC
i2c: cadence: Add standard bus recovery support
i2c: mlxbf: add multi slave functionality
i2c: mlxbf: support lock mechanism
macintosh/ams: Adapt declaration of ams_i2c_remove() to earlier change
i2c: riic: Use devm_platform_ioremap_resource()
i2c: mlxbf: remove IRQF_ONESHOT
dt-bindings: i2c: rockchip: add rockchip,rk3128-i2c
dt-bindings: i2c: renesas,rcar-i2c: Add r8a779g0 support
i2c: tegra: Add GPCDMA support
i2c: scmi: Convert to be a platform driver
i2c: rk3x: Add rv1126 support
...
|
|
into clk-next
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on RaspberryPi
- Mark PLLC critical on bcm2835
- Support for Renesas VersaClock7 clock generator family
* clk-baikal:
clk: baikal-t1: Convert to platform device driver
clk: baikal-t1: Add DDR/PCIe directly controlled resets support
dt-bindings: clk: baikal-t1: Add DDR/PCIe reset IDs
clk: baikal-t1: Move reset-controls code into a dedicated module
clk: baikal-t1: Add SATA internal ref clock buffer
clk: baikal-t1: Add shared xGMAC ref/ptp clocks internal parent
clk: baikal-t1: Fix invalid xGMAC PTP clock divider
clk: vc5: Fix 5P49V6901 outputs disabling when enabling FOD
* clk-broadcom:
clk: bcm: rpi: Add support for VEC clock
clk: bcm: rpi: Handle pixel clock in firmware
clk: bcm: rpi: Add support HEVC clock
clk: bcm2835: fix bcm2835_clock_rate_from_divisor declaration
clk: bcm2835: Round UART input clock up
clk: bcm2835: Make peripheral PLLC critical
* clk-vc5:
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
clk: vc5: Check IO access results
* clk-versaclock:
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
|
|
into clk-next
- More devm helpers for fixed rate registration
- Add Spreadtrum UMS512 SoC clk support
- Various PXA168 clk driver fixes
* clk-fixed-rate:
clk: fixed-rate: add devm_clk_hw_register_fixed_rate
clk: asm9260: use parent index to link the reference clock
* clk-spreadtrum:
clk: sprd: Add clocks support for UMS512
* clk-pxa:
clk: pxa: add a check for the return value of kzalloc()
clk: mmp: pxa168: control shared SDH bits with separate clock
dt-bindings: marvell,pxa168: add clock ids for SDH AXI clocks
clk: mmp: pxa168: add clocks for SDH2 and SDH3
dt-bindings: marvell,pxa168: add clock id for SDH3
clk: mmp: pxa168: fix GPIO clock enable bits
clk: mmp: pxa168: add muxes for more peripherals
clk: mmp: pxa168: fix incorrect parent clocks
clk: mmp: pxa168: fix const-correctness
clk: mmp: pxa168: add new clocks for peripherals
dt-bindings: marvell,pxa168: add clock ids for additional dividers
clk: mmp: pxa168: fix incorrect dividers
clk: mmp: pxa168: add additional register defines
* clk-ti:
clk: davinci: cfgchip: Use dev_err_probe() helper
clk: davinci: pll: fix spelling typo in comment
MAINTAINERS: add header file to TI DAVINCI SERIES CLOCK DRIVER
|
|
'clk-allwinner' and 'clk-imx' into clk-next
* clk-rockchip:
dt-bindings: clock: rockchip: change SPDX-License-Identifier
dt-bindings: clock: convert rockchip,rk3128-cru.txt to YAML
clk: rockchip: Add clock controller support for RV1126 SoC
dt-bindings: clock: rockchip: Document RV1126 CRU
clk: rockchip: Add dt-binding header for RV1126
clk: rockchip: Add MUXTBL variant
* clk-renesas:
clk: renesas: r8a779g0: Add EtherAVB clocks
clk: renesas: r8a779g0: Add PFC/GPIO clocks
clk: renesas: r8a779g0: Add I2C clocks
clk: renesas: r8a779g0: Add watchdog clock
dt-bindings: clock: renesas,rzg2l: Document RZ/Five SoC
clk: renesas: r8a779f0: Add MSIOF clocks
clk: renesas: r9a09g011: Add IIC clock and reset entries
clk: renesas: r9a07g044: Add conditional compilation for r9a07g044_cpg_info
clk: renesas: r8a779f0: Add TMU and parent SASYNC clocks
clk: renesas: r8a779f0: Add CMT clocks
clk: renesas: r8a779f0: Add SDH0 clock
* clk-microchip:
clk: at91: sama5d2: Add Generic Clocks for UART/USART
clk: microchip: add PolarFire SoC fabric clock support
dt-bindings: clk: add PolarFire SoC fabric clock ids
dt-bindings: clk: document PolarFire SoC fabric clocks
dt-bindings: clk: rename mpfs-clkcfg binding
clk: microchip: mpfs: update module authorship & licencing
clk: microchip: mpfs: convert periph_clk to clk_gate
clk: microchip: mpfs: convert cfg_clk to clk_divider
clk: microchip: mpfs: delete 2 line mpfs_clk_register_foo()
clk: microchip: mpfs: simplify control reg access
clk: microchip: mpfs: move id & offset out of clock structs
clk: microchip: mpfs: add MSS pll's set & round rate
MAINTAINERS: add polarfire soc reset controller
reset: add polarfire soc reset support
clk: microchip: mpfs: add reset controller
dt-bindings: clk: microchip: mpfs: add reset controller support
clk: microchip: mpfs: make the rtc's ahb clock critical
clk: microchip: mpfs: fix clk_cfg array bounds violation
* clk-allwinner:
clk: sunxi-ng: ccu-sun9i-a80-usb: Use dev_err_probe() helper
clk: sunxi-ng: ccu-sun9i-a80-de: Use dev_err_probe() helper
clk: sunxi-ng: sun8i-de2: Use dev_err_probe() helper
clk: sunxi-ng: d1: Limit PLL rates to stable ranges
* clk-imx:
clk: imx: scu: fix memleak on platform_device_add() fails
clk: imx93: add SAI IPG clk
clk: imx93: add MU1/2 clock
clk: imx93: switch to use new clk gate API
clk: imx: add i.MX93 clk gate
clk: imx: clk-composite-93: check white_list
clk: imx: clk-composite-93: check slice busy
dt-bindings: clock: imx93-clock: add more MU/SAI clocks
dt-bindings: clock: imx8mm: don't use multiple blank lines
clk: imx8mp: tune the order of enet_qos_root_clk
|
|
into clk-next
- Add resets for MediaTek MT8195 PCIe and USB
- Remove DaVinci DM644x and DM646x clk driver support
* clk-samsung:
clk: samsung: MAINTAINERS: add Krzysztof Kozlowski
clk: samsung: exynos850: Implement CMU_MFCMSCL domain
clk: samsung: exynos850: Implement CMU_IS domain
clk: samsung: exynos850: Implement CMU_AUD domain
clk: samsung: exynos850: Style fixes
clk: samsung: exynosautov9: add fsys1 clock support
clk: samsung: exynosautov9: add fsys0 clock support
clk: samsung: exynosautov9: correct register offsets of peric0/c1
clk: samsung: exynosautov9: add missing gate clks for peric0/c1
dt-bindings: clock: exynos850: Add Exynos850 CMU_MFCMSCL
dt-bindings: clock: exynos850: Add Exynos850 CMU_IS
dt-bindings: clock: exynos850: Add Exynos850 CMU_AUD
dt-bindings: clock: exynosautov9: add schema for cmu_fsys0/1
dt-bindings: clock: exynosautov9: add fsys1 clock definitions
dt-bindings: clock: exynosautov9: add fys0 clock definitions
clk: samsung: exynos7885: Add TREX clocks
clk: samsung: exynos7885: Implement CMU_FSYS domain
dt-bindings: clock: exynosautov9: correct clock numbering of peric0/c1
clk: samsung: exynos-clkout: Use of_device_get_match_data()
* clk-mtk: (42 commits)
clk: mediatek: add driver for MT8365 SoC
clk: mediatek: Export required common code symbols
clk: mediatek: Provide mtk_devm_alloc_clk_data
dt-bindings: clock: mediatek: add bindings for MT8365 SoC
clk: mediatek: mt8192: deduplicate parent clock lists
clk: mediatek: Migrate remaining clk_unregister_*() to clk_hw_unregister_*()
clk: mediatek: fix unregister function in mtk_clk_register_dividers cleanup
clk: mediatek: clk-mt8192: Add clock mux notifier for mfg_pll_sel
clk: mediatek: clk-mt8192-mfg: Propagate rate changes to parent
clk: mediatek: clk-mt8195-topckgen: Drop univplls from mfg mux parents
clk: mediatek: clk-mt8195-topckgen: Add GPU clock mux notifier
clk: mediatek: clk-mt8195-topckgen: Register mfg_ck_fast_ref as generic mux
clk: mediatek: clk-mt8195-mfg: Reparent mfg_bg3d and propagate rate changes
clk: mediatek: mt8183: Add clk mux notifier for MFG mux
clk: mediatek: mux: add clk notifier functions
clk: mediatek: mt8183: mfgcfg: Propagate rate changes to parent
clk: mediatek: Use mtk_clk_register_gates_with_dev in simple probe
clk: mediatek: gate: Export mtk_clk_register_gates_with_dev
clk: mediatek: add VDOSYS1 clock
dt-bindings: clk: mediatek: Add MT8195 DPI clocks
...
* clk-rm:
clk: davinci: remove PLL and PSC clocks for DaVinci DM644x and DM646x
* clk-ast:
clk: ast2600: BCLK comes from EPLL
* clk-qcom: (97 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: qcom: gcc-msm8939: use ARRAY_SIZE instead of specifying num_parents
clk: qcom: gcc-msm8939: use parent_hws where possible
dt-bindings: clock: move qcom,gcc-msm8939 to qcom,gcc-msm8916.yaml
clk: qcom: gcc-sm6350: Update the .pwrsts for usb gdscs
clk: qcom: gcc-sc8280xp: use retention for USB power domains
clk: qcom: gdsc: add missing error handling
dt-bindings: clocks: qcom,gcc-sc8280xp: Fix typos
clk: qcom: Add global clock controller driver for SM6375
dt-bindings: clock: add SM6375 QCOM global clock bindings
clk: qcom: alpha: Add support for programming the PLL_FSM_LEGACY_MODE bit
clk: qcom: gcc-sc7280: Update the .pwrsts for usb gdscs
clk: qcom: gcc-sc7180: Update the .pwrsts for usb gdsc
clk: qcom: gdsc: Fix the handling of PWRSTS_RET support
clk: qcom: Add SC8280XP GPU clock controller
dt-bindings: clock: Add Qualcomm SC8280XP GPU binding
clk: qcom: smd: Add SM6375 clocks
...
|
|
'clk-xilinx' into clk-next
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
* clk-ofnode:
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: tegra20: Fix refcount leak in tegra20_clock_init
clk: tegra: Fix refcount leak in tegra114_clock_init
clk: tegra: Fix refcount leak in tegra210_clock_init
clk: sprd: Hold reference returned by of_get_parent()
clk: berlin: Add of_node_put() for of_get_parent()
clk: at91: dt-compat: Hold reference returned by of_get_parent()
clk: qoriq: Hold reference returned by of_get_parent()
clk: oxnas: Hold reference returned by of_get_parent()
clk: st: Hold reference returned by of_get_parent()
clk: tegra: Add missing of_node_put()
clk: meson: Hold reference returned by of_get_parent()
clk: nomadik: Add missing of_node_put()
* clk-bindings:
dt-bindings: clock: drop minItems equal to maxItems
dt-bindings: clock: gpio-gate-clock: Convert to json-schema
dt-bindings: clock: Move versaclock.h to dt-bindings/clock
dt-bindings: clock: Move lochnagar.h to dt-bindings/clock
* clk-cleanup:
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: nxp: fix typo in comment
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clkdev: Simplify devm_clk_hw_register_clkdev() function
clkdev: Remove never used devm_clk_release_clkdev()
clk: Remove never used devm_of_clk_del_provider()
clk: pistachio: Fix initconst confusion
clk: clk-npcm7xx: Remove unused struct npcm7xx_clk_gate_data and npcm7xx_clk_div_fixed_data
clk: do not initialize ret
clk: remove extra empty line
clk: Fix comment typo
clk: move from strlcpy with unused retval to strscpy
* clk-zynq:
clk: zynqmp: pll: rectify rate rounding in zynqmp_pll_round_rate
clk: zynqmp: Check the return type zynqmp_pm_query_data
clk: zynqmp: Add a check for NULL pointer
clk: zynqmp: Replaced strncpy() with strscpy()
clk: zynqmp: Fix stack-out-of-bounds in strncpy`
clk: zynqmp: make bestdiv unsigned
* clk-xilinx:
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: clocking-wizard: Update the compatible
clk: clocking-wizard: Fix the reconfig for 5.2
clk: clocking-wizard: Rename nr-outputs to xlnx,nr-outputs
clk: clocking-wizard: Move clocking-wizard out
dt-bindings: add documentation of xilinx clocking wizard
|
