summaryrefslogtreecommitdiff
path: root/drivers/firmware
AgeCommit message (Collapse)Author
2020-01-22Merge 5.5-rc7 into char-misc-nextGreg Kroah-Hartman
We need the char-misc fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-21Merge tag 'zynqmp-soc-for-v5.6' of https://github.com/Xilinx/linux-xlnx into ↵Olof Johansson
arm/drivers arm64: soc: ZynqMP SoC changes for v5.6 - Extend firmware interface for feature checking - Use mailbox for communication with firmware for power management * tag 'zynqmp-soc-for-v5.6' of https://github.com/Xilinx/linux-xlnx: drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: firmware: xilinx: Add support for feature check Link: https://lore.kernel.org/r/f6fb26f8-b00d-a3e8-bf7d-c7ff2a8483b1@monstr.eu Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-20efi: Fix handling of multiple efi_fake_mem= entriesDan Williams
Dave noticed that when specifying multiple efi_fake_mem= entries only the last entry was successfully being reflected in the efi memory map. This is due to the fact that the efi_memmap_insert() is being called multiple times, but on successive invocations the insertion should be applied to the last new memmap rather than the original map at efi_fake_memmap() entry. Rework efi_fake_memmap() to install the new memory map after each efi_fake_mem= entry is parsed. This also fixes an issue in efi_fake_memmap() that caused it to litter emtpy entries into the end of the efi memory map. An empty entry causes efi_memmap_insert() to attempt more memmap splits / copies than efi_memmap_split_count() accounted for when sizing the new map. When that happens efi_memmap_insert() may overrun its allocation, and if you are lucky will spill over to an unmapped page leading to crash signature like the following rather than silent corruption: BUG: unable to handle page fault for address: ffffffffff281000 [..] RIP: 0010:efi_memmap_insert+0x11d/0x191 [..] Call Trace: ? bgrt_init+0xbe/0xbe ? efi_arch_mem_reserve+0x1cb/0x228 ? acpi_parse_bgrt+0xa/0xd ? acpi_table_parse+0x86/0xb8 ? acpi_boot_init+0x494/0x4e3 ? acpi_parse_x2apic+0x87/0x87 ? setup_acpi_sci+0xa2/0xa2 ? setup_arch+0x8db/0x9e1 ? start_kernel+0x6a/0x547 ? secondary_startup_64+0xb6/0xc0 Commit af1648984828 "x86/efi: Update e820 with reserved EFI boot services data to fix kexec breakage" introduced more occurrences where efi_memmap_insert() is invoked after an efi_fake_mem= configuration has been parsed. Previously the side effects of vestigial empty entries were benign, but with commit af1648984828 that follow-on efi_memmap_insert() invocation triggers efi_memmap_insert() overruns. Reported-by: Dave Young <dyoung@redhat.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20191231014630.GA24942@dhcp-128-65.nay.redhat.com Link: https://lore.kernel.org/r/20200113172245.27925-14-ardb@kernel.org
2020-01-20efi: Fix efi_memmap_alloc() leaksDan Williams
With efi_fake_memmap() and efi_arch_mem_reserve() the efi table may be updated and replaced multiple times. When that happens a previous dynamically allocated efi memory map can be garbage collected. Use the new EFI_MEMMAP_{SLAB,MEMBLOCK} flags to detect when a dynamically allocated memory map is being replaced. Debug statements in efi_memmap_free() reveal: efi: __efi_memmap_free:37: phys: 0x23ffdd580 size: 2688 flags: 0x2 efi: __efi_memmap_free:37: phys: 0x9db00 size: 2640 flags: 0x2 efi: __efi_memmap_free:37: phys: 0x9e580 size: 2640 flags: 0x2 ...a savings of 7968 bytes on a qemu boot with 2 entries specified to efi_fake_mem=. [ ardb: added a comment to clarify that efi_memmap_free() does nothing when called from efi_clean_memmap(), i.e., with data->flags == 0x0 ] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200113172245.27925-13-ardb@kernel.org
2020-01-20efi: Add tracking for dynamically allocated memmapsDan Williams
In preparation for fixing efi_memmap_alloc() leaks, add support for recording whether the memmap was dynamically allocated from slab, memblock, or is the original physical memmap provided by the platform. Given this tracking is established in efi_memmap_alloc() and needs to be carried to efi_memmap_install(), use 'struct efi_memory_map_data' to convey the flags. Some small cleanups result from this reorganization, specifically the removal of local variables for 'phys' and 'size' that are already tracked in @data. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200113172245.27925-12-ardb@kernel.org
2020-01-20efi: Add a flags parameter to efi_memory_mapDan Williams
In preparation for garbage collecting dynamically allocated EFI memory maps, where the allocation method of memblock vs slab needs to be recalled, convert the existing 'late' flag into a 'flags' bitmask. Arrange for the flag to be passed via 'struct efi_memory_map_data'. This structure grows additional flags in follow-on changes. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200113172245.27925-11-ardb@kernel.org
2020-01-20efi: Fix comment for efi_mem_type() wrt absent physical addressesAnshuman Khandual
A previous commit f99afd08a45f ("efi: Update efi_mem_type() to return an error rather than 0") changed the return value from EFI_RESERVED_TYPE to -EINVAL when the searched physical address is not present in any memory descriptor. But the comment preceding the function never changed. Let's change the comment now to reflect the new return value -EINVAL. Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200113172245.27925-10-ardb@kernel.org
2020-01-20efi/arm: Defer probe of PCIe backed efifb on DT systemsArd Biesheuvel
The new of_devlink support breaks PCIe probing on ARM platforms booting via UEFI if the firmware exposes a EFI framebuffer that is backed by a PCI device. The reason is that the probing order gets reversed, resulting in a resource conflict on the framebuffer memory window when the PCIe probes last, causing it to give up entirely. Given that we rely on PCI quirks to deal with EFI framebuffers that get moved around in memory, we cannot simply drop the memory reservation, so instead, let's use the device link infrastructure to register this dependency, and force the probing to occur in the expected order. Co-developed-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Saravana Kannan <saravanak@google.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20200113172245.27925-9-ardb@kernel.org
2020-01-18Merge branch 'efi-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull EFI fixes from Ingo Molnar: "Three EFI fixes: - Fix a slow-boot-scrolling regression but making sure we use WC for EFI earlycon framebuffer mappings on x86 - Fix a mixed EFI mode boot crash - Disable paging explicitly before entering startup_32() in mixed mode bootup" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/efistub: Disable paging at mixed mode entry efi/libstub/random: Initialize pointer variables to zero for mixed mode efi/earlycon: Fix write-combine mapping on x86
2020-01-16Merge tag 'qcom-drivers-for-5.6' of ↵Olof Johansson
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers Qualcomm driver updates for v5.6 * SCM major refactoring and cleanup * Properly flag active only power domains as active only * Add SC7180 and SM8150 RPMH power domains * Return EPROBE_DEFER from QMI if packet family is not yet available * tag 'qcom-drivers-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (27 commits) firmware: qcom_scm: Dynamically support SMCCC and legacy conventions firmware: qcom_scm: Remove thin wrappers firmware: qcom_scm: Order functions, definitions by service/command firmware: qcom_scm-32: Add device argument to atomic calls firmware: qcom_scm-32: Create common legacy atomic call firmware: qcom_scm-32: Move SMCCC register filling to qcom_scm_call firmware: qcom_scm-32: Use qcom_scm_desc in non-atomic calls firmware: qcom_scm-32: Add funcnum IDs firmware: qcom_scm-32: Use SMC arch wrappers firmware: qcom_scm-64: Improve SMC convention detection firmware: qcom_scm-64: Move SMC register filling to qcom_scm_call_smccc firmware: qcom_scm-64: Add SCM results struct firmware: qcom_scm-64: Move svc/cmd/owner into qcom_scm_desc firmware: qcom_scm-64: Make SMC macros less magical firmware: qcom_scm: Remove unused qcom_scm_get_version firmware: qcom_scm: Apply consistent naming scheme to command IDs firmware: qcom_scm: Rename macros and structures soc: qcom: rpmhpd: Set 'active_only' for active only power domains firmware: scm: Add stubs for OCMEM and restore_sec_cfg_available dt-bindings: power: rpmpd: Convert rpmpd bindings to yaml ... Link: https://lore.kernel.org/r/20200113204405.GD3325@yoga Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-16Merge tag 'imx-driver-5.6' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers i.MX driver changes for 5.6: - Add i.MX8MP SoC driver support. - Allow IMX DSP Protocol driver to be built as module. - Add COMPILE_TEST for IMX_SCU_SOC driver to increase build coverage. - Print SoC type and revision in i.MX8 SoC driver, as this is useful information to have when looking through boot log. * tag 'imx-driver-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: firmware: imx: Allow IMX DSP to be selected as module soc: imx: Enable compile testing of IMX_SCU_SOC soc: imx: Add i.MX8MP SoC driver support soc: imx8: print SoC type and revision Link: https://lore.kernel.org/r/20200113034006.17430-1-shawnguo@kernel.org Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-16Merge tag 'mvebu-drivers-5.6-1' of git://git.infradead.org/linux-mvebu into ↵Olof Johansson
arm/drivers mvebu drivers for 5.6 (part 1) - Various cleanup on the following drivers: - Turris Mox rWTM firmware - Moxtet bus - Armada 37xx rWTM mailbox - Marvell EBU Device Bus * tag 'mvebu-drivers-5.6-1' of git://git.infradead.org/linux-mvebu: mailbox: armada-37xx-rwtm: convert to devm_platform_ioremap_resource memory: mvebu-devbus: convert to devm_platform_ioremap_resource bus: moxtet: declare moxtet_bus_type as static firmware: turris-mox-rwtm: small white space cleanup Link: https://lore.kernel.org/r/877e1x3nxc.fsf@FE-laptop Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-14firmware: stratix10-svc: Remove unneeded semicolonzhengbin
Fixes coccicheck warning: drivers/firmware/stratix10-svc.c:271:2-3: Unneeded semicolon drivers/firmware/stratix10-svc.c:515:2-3: Unneeded semicolon Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: zhengbin <zhengbin13@huawei.com> Link: https://lore.kernel.org/r/1576465378-11109-1-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14firmware: google: Probe for a GSMI handler in firmwareArthur Heymans
Currently this driver is loaded if the DMI string matches coreboot and has a proper smi_command in the ACPI FADT table, but a GSMI handler in SMM is an optional feature in coreboot. So probe for a SMM GSMI handler before initializing the driver. If the smihandler leaves the calling argument in %eax in the SMM save state untouched that generally means the is no handler for GSMI. Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Link: https://lore.kernel.org/r/20191118101934.22526-4-patrick.rudolph@9elements.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14firmware: google: Unregister driver_info on failure and exit in gsmiArthur Heymans
Fix a bug where the kernel module couldn't be loaded after unloading, as the platform driver wasn't released on exit. Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Link: https://lore.kernel.org/r/20191118101934.22526-3-patrick.rudolph@9elements.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-14firmware: google: Release devices before unregistering the busPatrick Rudolph
Fix a bug where the kernel module can't be loaded after it has been unloaded as the devices are still present and conflicting with the to be created coreboot devices. Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> Link: https://lore.kernel.org/r/20191118101934.22526-2-patrick.rudolph@9elements.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-01-12iscsi_ibft: Don't limits Targets and NICs to twoLubomir Rintel
According to iSCSI Boot Firmware Table Version 1.03 [1], the length of the control table is ">= 18", where the optional expansion structure pointer follow the mandatory ones. This allows for more than two NICs and Targets. [1] ftp://ftp.software.ibm.com/systems/support/bladecenter/iscsi_boot_firmware_table_v1.03.pdf Let's enforce the minimum length of the control structure instead instead of limiting it to the smallest allowed size. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Konrad Rzeszutek Wilk <konrad@darnok.org>
2020-01-10efi: Allow disabling PCI busmastering on bridges during bootMatthew Garrett
Add an option to disable the busmaster bit in the control register on all PCI bridges before calling ExitBootServices() and passing control to the runtime kernel. System firmware may configure the IOMMU to prevent malicious PCI devices from being able to attack the OS via DMA. However, since firmware can't guarantee that the OS is IOMMU-aware, it will tear down IOMMU configuration when ExitBootServices() is called. This leaves a window between where a hostile device could still cause damage before Linux configures the IOMMU again. If CONFIG_EFI_DISABLE_PCI_DMA is enabled or "efi=disable_early_pci_dma" is passed on the command line, the EFI stub will clear the busmaster bit on all PCI bridges before ExitBootServices() is called. This will prevent any malicious PCI devices from being able to perform DMA until the kernel reenables busmastering after configuring the IOMMU. This option may cause failures with some poorly behaved hardware and should not be enabled without testing. The kernel commandline options "efi=disable_early_pci_dma" or "efi=no_disable_early_pci_dma" may be used to override the default. Note that PCI devices downstream from PCI bridges are disconnected from their drivers first, using the UEFI driver model API, so that DMA can be disabled safely at the bridge level. [ardb: disconnect PCI I/O handles first, as suggested by Arvind] Co-developed-by: Matthew Garrett <mjg59@google.com> Signed-off-by: Matthew Garrett <mjg59@google.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Matthew Garrett <matthewgarrett@google.com> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20200103113953.9571-18-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2020-01-10efi/x86: Allow translating 64-bit arguments for mixed mode callsArvind Sankar
Introduce the ability to define macros to perform argument translation for the calls that need it, and define them for the boot services that we currently use. When calling 32-bit firmware methods in mixed mode, all output parameters that are 32-bit according to the firmware, but 64-bit in the kernel (ie OUT UINTN * or OUT VOID **) must be initialized in the kernel, or the upper 32 bits may contain garbage. Define macros that zero out the upper 32 bits of the output before invoking the firmware method. When a 32-bit EFI call takes 64-bit arguments, the mixed-mode call must push the two 32-bit halves as separate arguments onto the stack. This can be achieved by splitting the argument into its two halves when calling the assembler thunk. Define a macro to do this for the free_pages boot service. Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Matthew Garrett <mjg59@google.com> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20200103113953.9571-17-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2020-01-10Merge branch 'linus' into efi/core, to pick up fixesIngo Molnar
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2020-01-09firmware: imx: Allow IMX DSP to be selected as moduleDaniel Baluta
IMX DSP is only needed by SOF or any other module that wants to communicate with the DSP. When SOF is build as a module IMX DSP is forced to be built inside the kernel image. This is not optimal, so allow IMX DSP to be built as a module. Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-01-08Merge tag 'cpuidle_psci-v5.5-rc4' of ↵Olof Johansson
git://git.linaro.org/people/ulf.hansson/linux-pm into arm/drivers Initial support for hierarchical CPU arrangement, managed by PSCI and its corresponding cpuidle driver. This support is based upon using the generic PM domain, which already supports devices belonging to CPUs. Finally, these is a DTS patch that enables the hierarchical topology to be used for the Qcom 410c Dragonboard, which supports the PSCI OS-initiated mode. * tag 'cpuidle_psci-v5.5-rc4' of git://git.linaro.org/people/ulf.hansson/linux-pm: (611 commits) arm64: dts: Convert to the hierarchical CPU topology layout for MSM8916 cpuidle: psci: Add support for PM domains by using genpd PM / Domains: Introduce a genpd OF helper that removes a subdomain cpuidle: psci: Support CPU hotplug for the hierarchical model cpuidle: psci: Manage runtime PM in the idle path cpuidle: psci: Prepare to use OS initiated suspend mode via PM domains cpuidle: psci: Attach CPU devices to their PM domains cpuidle: psci: Add a helper to attach a CPU to its PM domain cpuidle: psci: Support hierarchical CPU idle states cpuidle: psci: Simplify OF parsing of CPU idle state nodes cpuidle: dt: Support hierarchical CPU idle states of: base: Add of_get_cpu_state_node() to get idle states for a CPU node firmware: psci: Export functions to manage the OSI mode dt: psci: Update DT bindings to support hierarchical PSCI states cpuidle: psci: Align psci_power_state count with idle state count Linux 5.5-rc4 locks: print unsigned ino in /proc/locks riscv: export flush_icache_all to modules riscv: reject invalid syscalls below -1 riscv: fix compile failure with EXPORT_SYMBOL() & !MMU ... Link: https://lore.kernel.org/r/20200102160820.3572-1-ulf.hansson@linaro.org Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-08firmware: turris-mox-rwtm: small white space cleanupDan Carpenter
This patch deletes a stray tab. Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: Colin King <colin.king@canonical.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2020-01-07firmware: qcom_scm: Dynamically support SMCCC and legacy conventionsElliot Berman
Dynamically support SMCCCC and legacy conventions by detecting which convention to use at runtime. qcom_scm_call_atomic and qcom_scm_call can then be moved in qcom_scm.c and use underlying convention backend as appropriate. Thus, rename qcom_scm-64,-32 to reflect that they are backends for -smc and -legacy, respectively. Also add support for making SCM calls earlier than when SCM driver probes to support use cases such as qcom_scm_set_cold_boot_addr. Support is added by lazily initializing the convention and guarding the query with a spin lock. The limitation of these early SCM calls is that they cannot use DMA, as in the case of >4 arguments for SMC convention and any non-atomic call for legacy convention. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-18-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm: Remove thin wrappersElliot Berman
qcom_scm-32 and qcom_scm-64 implementations are nearly identical, so make qcom_scm_call and qcom_scm_call_atomic unique to each and the SCM descriptor creation common to each. There are the following catches: - __qcom_scm_is_call_available is still in each -32,-64 implementation as the argument is unique to each convention - For some functions, only one implementation was provided in -32 or -64. The actual implementation was moved into qcom_scm.c - io_writel and io_readl in -64 were non-atomic calls and in -32 they were. Atomic is the better option, so use it. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-17-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm: Order functions, definitions by service/commandElliot Berman
Definitions throughout qcom_scm are loosely grouped and loosely ordered. Sort all the functions/definitions by service ID/command ID to improve sanity when needing to add new functionality to this driver. Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-16-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Add device argument to atomic callsElliot Berman
Add unused "device" parameter to reduce merge friction between SMCCC and legacy based conventions in an upcoming patch. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-15-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Create common legacy atomic callElliot Berman
Per [1], legacy calling convention supports up to 5 arguments and 3 return values. Create one function to support this combination, and remove the original "atomic1" and "atomic2" variants for 1 and 2 arguments. This more closely aligns scm_legacy implementation with scm_smc implementation. [1]: https://source.codeaurora.org/quic/la/kernel/msm-4.9/tree/drivers/soc/qcom/scm.c?h=kernel.lnx.4.9.r28-rel#n1024 Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-14-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Move SMCCC register filling to qcom_scm_callElliot Berman
Move SMCCC register filling to qcom_scm_call so that __scm_legacy_do only needs to concern itself with retry mechanism. qcom_scm_call then is responsible for translating qcom_scm_desc into the complete set of register arguments and passing onto qcom_scm_call_do. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-13-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Use qcom_scm_desc in non-atomic callsElliot Berman
Use qcom_scm_desc in non-atomic calls to remove legacy convention details from every SCM wrapper function. Implementations were copied from qcom_scm-64 and are functionally equivalent when using the qcom_scm_desc and qcom_scm_res structs. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-12-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Add funcnum IDsElliot Berman
Add SCM_LEGACY_FNID macro to qcom_scm-32. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-11-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-32: Use SMC arch wrappersElliot Berman
Use SMC arch wrappers instead of inline assembly. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-10-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-64: Improve SMC convention detectionElliot Berman
Improve the calling convention detection to use __qcom_scm_is_call_available() and not blindly assume 32-bit mode if the checks fails. BUG() if neither 32-bit or 64-bit mode works. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-9-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-64: Move SMC register filling to qcom_scm_call_smcccElliot Berman
qcom_scm_call_smccc should be responsible for converting qcom_scm_desc into arguments for smc call. Consolidate the dispersed logic to convert qcom_scm_desc into smc arguments inside qcom_scm_call_smccc. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-8-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-64: Add SCM results structElliot Berman
Remove knowledge of arm_smccc_res struct from client wrappers so that client wrappers only work QCOM SCM data structures. SCM calls may have up to 3 arguments, so qcom_scm_call_smccc is responsible now for filling those 3 arguments accordingly. This is necessary to support merging legacy and SMC conventions in an upcoming patch. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-7-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-64: Move svc/cmd/owner into qcom_scm_descElliot Berman
Service, command, and owner IDs are all part of qcom_scm_desc struct and have no special reason to be a function argument (or hard-coded in the case of owner [1]). Moving them to be part of qcom_scm_desc struct improves readability. [1]: Example of SCM function using owner vale other than hard-coded SIP value: https://source.codeaurora.org/quic/la/kernel/msm-4.9/tree/drivers/soc/qcom/smcinvoke.c?h=kernel.lnx.4.9.r28-rel#n35 Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-6-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm-64: Make SMC macros less magicalElliot Berman
Improve understandability of SMC macros by reversing the logic as they are all functions of how many arguments can be shoved in registers and how many SCM arguments are supported. There aren't 4 register arguments because are 7 arguments that go into a buffer - there are up to 7 arguments that are overflowed into a buffer because only 4 registers are allocated for arguments. Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-5-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm: Remove unused qcom_scm_get_versionElliot Berman
Remove unused qcom_scm_get_version. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-4-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm: Apply consistent naming scheme to command IDsElliot Berman
Create a consistent naming scheme for command IDs. The scheme is QCOM_SCM_##svc_##cmd. Remove unused macros QCOM_SCM_FLAG_HLOS, QCOM_SCM_FLAG_COLDBOOT_MC, QCOM_SCM_FLAG_WARMBOOT_MC, QCOM_SCM_CMD_CORE_HOTPLUGGED, and QCOM_SCM_BOOT_ADDR_MC. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-3-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-07firmware: qcom_scm: Rename macros and structuresElliot Berman
Rename legacy-specific structures and macros with legacy prefix; rename smc-specific structures and macros with smc prefix. This should make it clearer which structures are generic to "SCM" and which are specfically for implementing the convention. Tested-by: Brian Masney <masneyb@onstation.org> # arm32 Tested-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Elliot Berman <eberman@codeaurora.org> Link: https://lore.kernel.org/r/1578431066-19600-2-git-send-email-eberman@codeaurora.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2020-01-06firmware: tee_bnxt: Fix multiple call to tee_client_close_contextVikas Gupta
Fix calling multiple tee_client_close_context in case of shm allocation fails. Fixes: 246880958ac9 (“firmware: broadcom: add OP-TEE based BNXT f/w manager”) Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-06Merge tag 'scmi-updates-5.6' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/drivers ARM SCMI updates for v5.6 1. Addition of multiple device support per protocol to enable use of some procotols by multiple kernel subsystems simultaneously and corresponding updates to the existing scmi drivers 2. Addition of trace events around the scmi transfer code to measure any delays and capture anomalies that can also be used during investigation of some platform firmware related issues * tag 'scmi-updates-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: drivers: firmware: scmi: Extend SCMI transport layer by trace events include: trace: Add SCMI header with trace events reset: reset-scmi: Match scmi device by both name and protocol id hwmon: (scmi-hwmon) Match scmi device by both name and protocol id cpufreq: scmi: Match scmi device by both name and protocol id clk: scmi: Match scmi device by both name and protocol id firmware: arm_scmi: Skip protocol initialisation for additional devices firmware: arm_scmi: Stash version in protocol init functions firmware: arm_scmi: Match scmi device by both name and protocol id firmware: arm_scmi: Add versions and identifier attributes using dev_groups firmware: arm_scmi: Add names to scmi devices created firmware: arm_scmi: Skip scmi mbox channel setup for addtional devices firmware: arm_scmi: Add support for multiple device per protocol Link: https://lore.kernel.org/r/20191230182956.GA29349@bogus Signed-off-by: Olof Johansson <olof@lixom.net>
2020-01-06remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig
ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
2020-01-02firmware: psci: Export functions to manage the OSI modeUlf Hansson
To allow subsequent changes to implement support for OSI mode through the cpuidle-psci driver, export the existing psci_has_osi_support(). Export also a new function, psci_set_osi_mode(), that allows its caller to enable the OS-initiated CPU-suspend mode in the PSCI FW. To deal with backwards compatibility for a kernel started through a kexec call, default to set the CPU-suspend mode to the Platform Coordinated mode during boot. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
2019-12-30drivers: firmware: scmi: Extend SCMI transport layer by trace eventsLukasz Luba
The SCMI transport layer communicates via mailboxes and shared memory with firmware running on a microcontroller. It is platform specific how long it takes to pass a SCMI message. The most sensitive requests are coming from CPUFreq subsystem, which might be used by the scheduler. Thus, there is a need to measure these delays and capture anomalies. This change introduces trace events wrapped around transfer code. According to Jim's suggestion a unique transfer_id is to distinguish similar entries which might have the same message id, protocol id and sequence. This is a case then there are some timeouts in transfers. Suggested-by: Jim Quinlan <james.quinlan@broadcom.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2019-12-25efi/libstub: Tidy up types and names of global cmdline variablesArd Biesheuvel
Drop leading underscores and use bool not int for true/false variables set on the command line. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224151025.32482-25-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-12-25efi/libstub: Rename efi_call_early/_runtime macros to be more intuitiveArd Biesheuvel
The macros efi_call_early and efi_call_runtime are used to call EFI boot services and runtime services, respectively. However, the naming is confusing, given that the early vs runtime distinction may suggest that these are used for calling the same set of services either early or late (== at runtime), while in reality, the sets of services they can be used with are completely disjoint, and efi_call_runtime is also only usable in 'early' code. So do a global sweep to replace all occurrences with efi_bs_call or efi_rt_call, respectively, where BS and RT match the idiom used by the UEFI spec to refer to boot time or runtime services. While at it, use 'func' as the macro parameter name for the function pointers, which is less likely to collide and cause weird build errors. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224151025.32482-24-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-12-25efi/libstub: Drop 'table' argument from efi_table_attr() macroArd Biesheuvel
None of the definitions of the efi_table_attr() still refer to their 'table' argument so let's get rid of it entirely. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224151025.32482-23-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-12-25efi/libstub: Drop protocol argument from efi_call_proto() macroArd Biesheuvel
After refactoring the mixed mode support code, efi_call_proto() no longer uses its protocol argument in any of its implementation, so let's remove it altogether. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224151025.32482-22-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2019-12-25efi/libstub/x86: Work around page freeing issue in mixed modeArd Biesheuvel
Mixed mode translates calls from the 64-bit kernel into the 32-bit firmware by wrapping them in a call to a thunking routine that pushes a 32-bit word onto the stack for each argument passed to the function, regardless of the argument type. This works surprisingly well for most services and protocols, with the exception of ones that take explicit 64-bit arguments. efi_free() invokes the FreePages() EFI boot service, which takes a efi_physical_addr_t as its address argument, and this is one of those 64-bit types. This means that the 32-bit firmware will interpret the (addr, size) pair as a single 64-bit quantity, and since it is guaranteed to have the high word set (as size > 0), it will always fail due to the fact that EFI memory allocations are always < 4 GB on 32-bit firmware. So let's fix this by giving the thunking code a little hand, and pass two values for the address, and a third one for the size. Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Borislav Petkov <bp@alien8.de> Cc: James Morse <james.morse@arm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224151025.32482-21-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-14 07:05:38 +0000