| Age | Commit message (Collapse) | Author |
|---|
|
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
BXT's DSI PLL is different from that of VLV. So this patch
adds a new function to get the current DSI pixel clock based
on the PLL divider ratio and lane count.
This function is required for intel_dsi_get_config() function.
v2: Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pick appropriate port control register (BXT or VLV), based on device.
Get the current hw state wrt Mipi port.
v2: Rebased on latest drm nightly branch.
v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
implementations as per Jani's suggestion.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch contains changes to support DSI disble sequence in BXT.
The changes are:
1. BXT specific changes in clear_device_ready function.
2. BXT specific changes in DSI disable and post-disable functions.
3. Add a new function to reset BXT Dphy clock and dividers
(bxt_dsi_reset_clocks).
4. Moved some part of the vlv clock reset code, in a new function
(vlv_dsi_reset_clocks) maintaining the exact same sequence.
5. Wrapper function to call corresponding reset clock function.
v2: Fixed Jani's review comments.
v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
implementations as per Jani's suggestion.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
(Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock
v2: Fixed Jani's review comments. Adjusted the Macro definition as
per convention. Simplified the logic for bit definitions for
MIPI PORT A and PORT C in same registers.
v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
Jani's suggestion.
v4: Addressed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
are specific to BXT device ready sequence. Added check for
ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV
v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
code. Fixed the macros to get proper port offsets.
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
SKL and BXT qualifies the HAS_DDI() check, and hence haswell
modeset functions are re-used for modeset sequence. But DDI
interface doesn't include support for DSI.
This patch adds:
1. cases for DSI encoder, in those modeset functions and allows
a CRTC modeset
2. Adds call to pre_pll enabled from CRTC modeset function. Nothing
needs to be done as such in CRTC for DSI encoder, as PLL, clock
and and transcoder programming will be taken care in encoder's
pre_enable and pre_pll_enable function.
v2: Fixed Jani's review comments. Added INVALID_PORT for non DDI
encoder like DSI for platforms having HAS_DDI as true.
v3: Rebased on latest drm-nightly branch. Added a WARN_ON for invalid
encoder.
v4: WARN_ON for invalid encoder is refactored as per Jani's suggestion.
Fixed the sequence for pre_pll_enable.
v5: Protected DDI code paths in case of DSI encoder calls.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.
Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
- initialize backlight from VBT as fallback (Jani)
- hpd A support from Ville
- various atomic polish all over (mostly from Maarten)
- first parts of virtualize gpu guest support on bdw from
Zhiyuan Lv
- GuC fixes from Alex
- polish for the chv clocks code (Ville)
- various things all over, as usual
* tag 'drm-intel-next-2015-09-11' of git://anongit.freedesktop.org/drm-intel: (145 commits)
drm/i915: Update DRIVER_DATE to 20150911
drm/i915: Remove one very outdated comment
drm/i915: Use crtc->state for duplication.
drm/i915: Do not handle a null plane state.
drm/i915: Remove legacy plane updates for cursor and sprite planes.
drm/i915: Use atomic state when changing cursor visibility.
drm/i915: Use the atomic state in intel_update_primary_planes.
drm/i915: Use the plane state in intel_crtc_info.
drm/i915: Use atomic plane state in the primary plane update.
drm/i915: add attached connector to hdmi container
drm/i915: don't hard code vlv backlight frequency if unset
drm/i915: initialize backlight max from VBT
drm/i915: use pch backlight override on hsw too
drm/i915/bxt: Clean up bxt_init_clock_gating
drm/i915: Fix cmdparser STORE/LOAD command descriptors
drm/i915: Dump pfit state as hex
drm/i915: access the PP_ON_DELAYS/PP_OFF_DELAYS regs only pre GEN5
drm/i915: access the PP_CONTROL reg only pre GEN5
drm/i915: Refactor common ringbuffer allocation code
drm/i915: use the yesno helper for logging
...
|
|
This just removes the magic number.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Since 9eb1e57f564d4e6e10991402726cc83fe0b9172f
drm/dp/mst: make sure mst_primary mstb is valid in work function
we validate the mstb structs in the work function, and doing
that takes a reference. So we should never get here with the
work function running using the mstb device, only if the work
function hasn't run yet or is running for another mstb.
So we don't need to sync the work here, this was causing
lockdep spew as below.
[ +0.000160] =============================================
[ +0.000001] [ INFO: possible recursive locking detected ]
[ +0.000002] 3.10.0-320.el7.rhel72.stable.backport.3.x86_64.debug #1 Tainted: G W ------------
[ +0.000001] ---------------------------------------------
[ +0.000001] kworker/4:2/1262 is trying to acquire lock:
[ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b29a5>] flush_work+0x5/0x2e0
[ +0.000007]
but task is already holding lock:
[ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710
[ +0.000004]
other info that might help us debug this:
[ +0.000001] Possible unsafe locking scenario:
[ +0.000002] CPU0
[ +0.000000] ----
[ +0.000001] lock((&mgr->work));
[ +0.000002] lock((&mgr->work));
[ +0.000001]
*** DEADLOCK ***
[ +0.000001] May be due to missing lock nesting notation
[ +0.000002] 2 locks held by kworker/4:2/1262:
[ +0.000001] #0: (events_long){.+.+.+}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710
[ +0.000004] #1: ((&mgr->work)){+.+.+.}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710
[ +0.000003]
stack backtrace:
[ +0.000003] CPU: 4 PID: 1262 Comm: kworker/4:2 Tainted: G W ------------ 3.10.0-320.el7.rhel72.stable.backport.3.x86_64.debug #1
[ +0.000001] Hardware name: LENOVO 20EGS0R600/20EGS0R600, BIOS GNET71WW (2.19 ) 02/05/2015
[ +0.000008] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ +0.000001] ffffffff82c26c90 00000000a527b914 ffff88046399bae8 ffffffff816fe04d
[ +0.000004] ffff88046399bb58 ffffffff8110f47f ffff880461438000 0001009b840fc003
[ +0.000002] ffff880461438a98 0000000000000000 0000000804dc26e1 ffffffff824a2c00
[ +0.000003] Call Trace:
[ +0.000004] [<ffffffff816fe04d>] dump_stack+0x19/0x1b
[ +0.000004] [<ffffffff8110f47f>] __lock_acquire+0x115f/0x1250
[ +0.000002] [<ffffffff8110fd49>] lock_acquire+0x99/0x1e0
[ +0.000002] [<ffffffff810b29a5>] ? flush_work+0x5/0x2e0
[ +0.000002] [<ffffffff810b29ee>] flush_work+0x4e/0x2e0
[ +0.000002] [<ffffffff810b29a5>] ? flush_work+0x5/0x2e0
[ +0.000004] [<ffffffff81025905>] ? native_sched_clock+0x35/0x80
[ +0.000002] [<ffffffff81025959>] ? sched_clock+0x9/0x10
[ +0.000002] [<ffffffff810da1f5>] ? local_clock+0x25/0x30
[ +0.000002] [<ffffffff8110dca9>] ? mark_held_locks+0xb9/0x140
[ +0.000003] [<ffffffff810b4ed5>] ? __cancel_work_timer+0x95/0x160
[ +0.000002] [<ffffffff810b4ee8>] __cancel_work_timer+0xa8/0x160
[ +0.000002] [<ffffffff810b4fb0>] cancel_work_sync+0x10/0x20
[ +0.000007] [<ffffffffa0160d17>] drm_dp_destroy_mst_branch_device+0x27/0x120 [drm_kms_helper]
[ +0.000006] [<ffffffffa0163968>] drm_dp_mst_link_probe_work+0x78/0xa0 [drm_kms_helper]
[ +0.000002] [<ffffffff810b5850>] process_one_work+0x220/0x710
[ +0.000002] [<ffffffff810b57e4>] ? process_one_work+0x1b4/0x710
[ +0.000005] [<ffffffff810b5e5b>] worker_thread+0x11b/0x3a0
[ +0.000003] [<ffffffff810b5d40>] ? process_one_work+0x710/0x710
[ +0.000002] [<ffffffff810beced>] kthread+0xed/0x100
[ +0.000003] [<ffffffff810bec00>] ? insert_kthread_work+0x80/0x80
[ +0.000003] [<ffffffff817121d8>] ret_from_fork+0x58/0x90
v2: add flush_work.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In order to cache the EDID properly for tiled displays, we
need to retrieve it before we register the connector with
userspace, otherwise userspace can call get resources
and try and get the edid before we've even cached it.
This fixes some problems when hotplugging mst monitors,
with X/mutter running. As mutter seems to get 0 modes
for one of the monitors in the tile.
v2: fix warning in radeon
handle tile setting in cached path rather than
get edid path.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Update the state before sending the msg to close it.
v2: reset value if return indicates we haven't send the msg.
v3: just clean the code up.
Pointed out by Adam J Richter on
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91481
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
output ports should always have a connector, unless
in the rare case connector allocation fails in the
driver.
In this case we only need to teardown the pdt,
and free the struct, and there is no need to
send a hotplug msg.
In the case were we add the port to the destroy
list we need to send a hotplug if we destroy
any connectors, so userspace knows to reprobe
stuff.
this patch also handles port->connector allocation
failing which should be a rare event, but makes
the code consistent.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is unnecessary and it makes it easier to see what is needed
from port.
also add blank line to make things nicer.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
It was just a wrapper around drm_fb_helper_set_par that
called cursor_set2 in addition. Now that the core handles
this, drop this radeon specific version.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If a driver uses the cursor_set2 crtc callback rather than
cursor_set, use that. This fixes the fbdev helper for drivers
that use cursor_set2.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
a few i915 fixes for v4.3.
* tag 'drm-intel-fixes-2015-10-01' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
drm/i915: Consider HW CSB write pointer before resetting the sw read pointer
drm/i915/skl: Don't call intel_prepare_ddi when encoder list isn't yet initialized.
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
A single commit to fix a command submission hang regression.
Pull request of 2015-10-01
* tag 'vmwgfx-fixes-4.3-151001' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix a command submission hang regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
This pull request includes regression fixups, build warnings, and
trivial cleanups which mostly remove some codes not used anymore.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Staticize local function in exynos_drm_gem.c
drm/exynos: fimd: actually disable dp clock
drm/exynos: dp: remove suspend/resume functions
drm/exynos: remove unused mode_fixup() code
drm/exynos: remove decon_mode_fixup()
drm/exynos: remove fimd_mode_fixup()
drm/exynos: rotator: Clock control is unused if !PM
drm/exynos: fimc: Clock control is unused if !PM
drm/exynos: Suspend/resume is unused if !PM
drm/exynos: create a fake mmap offset with gem creation
drm/exynos: remove call to drm_gem_free_mmap_offset()
drm/exynos: Remove useless EXPORT_SYMBOL_GPLs
drm/exynos: cleanup line feed in exynos_drm_gem_get_ioctl
drm/exynos: cleanup function calling written twice
drm/exynos: staticize exynos_drm_gem_init()
drm/exynos: remove unnecessary NULL assignment
drm/exynos: fix missed calling of drm_prime_gem_destroy()
drm/exynos: fix layering violation of address
|
|
into drm-fixes
radeon and amdgpu fixes for 4.3.
- backlight s/r fixes
- typo fix from Dan
- vm debugging fix
- remove import_gpu_mem after discussion with Daniel
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: only print meaningful VM faults
drm/amdgpu/cgs: remove import_gpu_mem
drm/amdgpu: Restore LCD backlight level on resume
drm/radeon: Restore LCD backlight level on resume (>= R5xx)
drm/amdgpu: signedness bug in amdgpu_cs_parser_init()
|
|
There are some allocations that must be only referenced by 32-bit
offsets. To limit the chances of having the first 4GB already full,
objects not requiring this workaround use DRM_MM_SEARCH_BELOW/
DRM_MM_CREATE_TOP flags
In specific, any resource used with flat/heapless (0x00000000-0xfffff000)
General State Heap (GSH) or Instruction State Heap (ISH) must be in a
32-bit range, because the General State Offset and Instruction State
Offset are limited to 32-bits.
Objects must have EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag to indicate if
they can be allocated above the 32-bit address range. To limit the
chances of having the first 4GB already full, objects will use
DRM_MM_SEARCH_BELOW + DRM_MM_CREATE_TOP flags when possible.
The libdrm user of the EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag is here:
http://lists.freedesktop.org/archives/intel-gfx/2015-September/075836.html
v2: Changed flag logic from neeeds_32b, to supports_48b.
v3: Moved 48-bit support flag back to exec_object. (Chris, Daniel)
v4: Split pin flags into PIN_ZONE_4G and PIN_HIGH; update PIN_OFFSET_MASK
to use last PIN_ defined instead of hard-coded value; use correct limit
check in eb_vma_misplaced. (Chris)
v5: Don't touch PIN_OFFSET_MASK and update workaround comment (Chris)
v6: Apply pin-high for ggtt too (Chris)
v7: Handle simultaneous pin-high and pin-mappable end correctly (Akash)
Fix check for entries currently using +4GB addresses, use min_t and
other polish in object_bind_to_vm (Chris)
v8: Commit message updated to point to libdrm patch.
v9: vmas are allocated in the correct ozone, so only check flag when the
vma has not been allocated. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Due to flip interrupts GuC stays awake always and GT does not enter
RC6. Do not route those interrupts to GuC for now. Driver won't touch
DE_GUCRMR register and leave it as what default value.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Move the wakeup for the frame wait into the armada plane work, to
ensure that it is woken up every time we run a work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the overlay plane to use the generic armada plane worker
infrastructure which is shared with the primary plane.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a plane work implementation, and move the CRTC framebuffer flip
work to it for the primary plane. The idea is to have a common
plane work implementation for both the primary and overlay planes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Both the CRTC and overlay frames have their own wait queues. It would
make more sense if these were part of the plane - the primary plane for
the CRTC and overlay plane for the overlay.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the locking for armada_drm_vbl_event_remove() into itself, which
makes this function symmetrical with armada_drm_vbl_event_add().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It is not necessary to write dplane->ctrl0 under the CRTC spinlock, as
this is only accessed under process context where the DRM locks will
protect us instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the write to clear the DMA enable bit, and augment it with clearing
the graphics enable bit for the primary plane.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Provide a common helper to disable either the overlay or the primary
plane.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Allocate our own primary plane as an armada_plane.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use drm_primary_helper_create_plane() to create our primary plane, and
register the CRTC with drm_crtc_init_with_planes(). This enables the
primary plane to be initialised with the supported format information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Introduce a generic armada_plane struct which will eventually be used
for both the primary and overlay planes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use the new drm_universal_plane_init() rather than the legacy
drm_plane_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than using a spinlock, use xchg() to atomically update
dplane->old_fb. This allows us to eliminate dplane->lock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If we couldn't get a high precisions vblank timestamp, we currently
store a zeroed timestamp instead and assume the next vblank irq to
get us something better. This makes sense when trying to update the
timestamp from eg. vblank enable. But if we do this from the vblank
irq we will never get a vblank timestamp unless we high precision
timestamps are available and succeeded. This break weston for instance
on drivers lacking high precision timestamps.
To fix this, zero the timestamp only when not called from vbl irq.
When called from the irq, we still want the timestamp, even if not
perfect.
This fixes a regression from
4dfd64862ff852df drm: Use vblank timestamps to guesstimate how many vblanks were missed
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Surprisingly kbuild can't cope with tristates in the
<module>-$(CONFIG_FOO) pattern. This patch hacks up a solution.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michal Marek <mmarek@suse.com>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
The exynos_drm_gem_mmap_buffer() is not used outside so make it static.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
fimd_dp_clock_enable() was setting the always to enabled,
this patch fix this to actually use the value that is set to 'val'.
Reported-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch removes unnecessary pm suspend/resume functions.
All kms sub drivers will be controlled by top of Exynos drm driver
and connector dpms so these sub drivers shouldn't have their own
pm interfaces.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
When disabling/enabling a crtc the primary area must be updated
independently of which crtc has been disabled/enabled.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1264735
Signed-off-by: Fabiano Fidêncio <fidencio@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Port of radeon commit 9b7d786b900baf7c0d1a7e211570aef1cb27590f.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It was added for completeness, but we don't have any users
for it yet. Daniel noted that it may be racy. Remove it.
Change-Id: I5f5546f8911a4f294008a62dc86a73f3face38d1
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We already ensure that pstate->visible = false when crtc->active = false
during runtime programming; make sure we follow the same logic when
reading out initial hardware state.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
