| Age | Commit message (Collapse) | Author |
|---|
|
Add driver for the TCON (timing controller) module. The TCON module
is a separate module attached after the DCU (display controller
unit). Each DCU instance has its own, directly connected TCON
instance. The DCU's RGB and timing signals are passing through
the TCON module. TCON can provide timing signals for raw TFT panels
or operate in a bypass mode which leaves all signals unaltered.
The driver currently only supports the bypass mode.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Use the common clock framework to calculate the pixel clock
dividier. The previous implementation rounded down the calculated
factor. Thanks to the CLK_DIVIDER_ROUND_CLOSEST flag using the
common clock framework divider implementation improves the pixel
clock accuracy in some cases. Ontop of that it also allows to see
the actual pixel clock in the sysfs clock summary.
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
The Vybrid DCU variant has two independent clock inputs, one
for the registers (IPG bus clock) and one for the pixel clock.
Support this distinction in the DCU DRM driver while staying
backward compatible for old device trees.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Fix error handling during probe by reordering initialization and
adding a error path which disables clock again. Also disable the
clock on remove.
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Changes for v4.7-rc1" from Thierry Reding:
This contains a bunch of preparatory patches to the PMC driver which are
a prerequisite to moving the driver to generic power domains.
* tag 'tegra-for-4.7-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Update NVIDIA PMC for Tegra
soc/tegra: pmc: Wait for powergate state to change
soc/tegra: pmc: Ensure GPU partition can be toggled on/off by PMC
soc/tegra: pmc: Remove additional check for a valid partition
soc/tegra: pmc: Fix verification of valid partitions
soc/tegra: pmc: Fix testing of powergate state
soc/tegra: pmc: Change powergate and rail IDs to be an unsigned type
soc/tegra: pmc: Protect public functions from potential race conditions
soc/tegra: pmc: Restore base address on probe failure
soc/tegra: pmc: Remove non-existing L2 partition for Tegra124
soc/tegra: pmc: Remove non-existing power partitions for Tegra210
soc/tegra: pmc: Remove debugfs entry on probe failure
soc/tegra: pmc: Fix sparse warning for tegra_pmc_init_tsense_reset()
soc/tegra: pmc: Add missing structure members to kernel-doc
|
|
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
http://github.com/Broadcom/stblinux into next/dt
Merge "Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Rafal adds proper VCC GPIO to be fed to the USB host controllers for known
BCM5301x devices needing that, he also enables earlycon, and enables the
SPI-NOR flashes on relevant devices
- Eric adds the VideoCore 4 Device Tree nodes to the BCM283x Device Tree and
provides a DRM patch to kick out the simplefb framebuffer to avoid conflicts
- Stephan adds proper CPU nodes for the ARM processor on the BCM2835 SoC Device
Tree
- Martin provides a binding fix for the DMA channel interrupt numbers and
description
* tag 'arm-soc/for-4.7/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add DT entry for SPI controller and NOR flash
dt/bindings: bcm2835: correct description for DMA-int
ARM: bcm2835: add CPU node for ARM core
ARM: bcm2835: Add VC4 to the device tree.
drm/vc4: Kick out the simplefb framebuffer before we set up KMS.
ARM: BCM5301X: Enable earlycon on tested devices
ARM: BCM5301X: Set vcc-gpio for USB controllers of few devices
|
|
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-3-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Commit d63c25e4245a ("drm: rcar-du: Use generic
drm_connector_register_all() helper") left an unused local variable
behind. Remove it.
Fixes: d63c25e4245a ("drm: rcar-du: Use generic drm_connector_register_all() helper")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The VSP1 compositor code in DRM links against the respective V4L
driver, but the dependency is not expressed correctly in Kconfig,
which leads to a build error when the DRM driver is built-in
and the V4L driver is a module:
drivers/gpu/built-in.o: In function `rcar_du_vsp_plane_atomic_update':
rcar-du/rcar_du_vsp.c:183: undefined reference to `vsp1_du_atomic_update'
This patch avoids the problem by ensuring that the DRM VSP code can
only be enabled if the V4L driver is linked into the kernel, or
both are loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6d62ef3ac30b ("drm: rcar-du: Expose the VSP1 compositor through KMS planes")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
|
|
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes: 237ed86c693d ("drm/i915: Check live status before reading edid")
Cc: stable@vger.kernel.org # v4.4
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
Commit d63c25e4245a ("drm: rcar-du: Use generic
drm_connector_register_all() helper") left an unused local variable
behind. Remove it.
Fixes: d63c25e4245a ("drm: rcar-du: Use generic drm_connector_register_all() helper")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1461336879-2469-1-git-send-email-laurent.pinchart+renesas@ideasonboard.com
|
|
Since we've fixed up drm_dp_dpcd_read() to allow for retries when things
timeout, there's no use for having this function anymore. Good riddens.
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460559513-32280-5-git-send-email-cpaul@redhat.com
|
|
This is part of a patch series to migrate all of the workarounds for
commonly seen behavior from bad sinks in intel_dp_dpcd_read_wake() to drm's
DP helper.
Some sinks will just return garbage for the first aux tranaction they
receive when coming out of sleep mode, so we need to perform an additional
read before the actual read to workaround this.
Changes since v5
- If the throwaway read in drm_dp_dpcd_read() fails, return the error
from that instead of continuing. This follows the same logic we do in
drm_dp_dpcd_access() (e.g. the error from the first transaction may
differ from the errors that proceeding attempts might return).
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460730335-5012-1-git-send-email-cpaul@redhat.com
|
|
This is part of a patch series to migrate all of the workarounds for
commonly seen behavior from bad sinks in intel_dp_dpcd_read_wake() to
drm's DP helper.
We cannot rely on sinks NACKing or deferring when they can't receive
transactions, nor can we rely on any other sort of consistent error to
know when we should stop retrying. As such, we need to just retry
unconditionally on errors. We also make sure here to return the error we
encountered during the first transaction, since it's possible that
retrying the transaction might return a different error then we had
originally.
This, along with the previous patch, work around a weird bug with the
ThinkPad T560's and it's dock. When resuming the laptop, it appears that
there's a short period of time where we're unable to complete any aux
transactions, as they all immediately timeout. The only machine I'm able
to reproduce this on is the T560 as other production Skylake models seem
to be fine. The period during which AUX transactions fail appears to be
around 22ms long. AFAIK, the dock for the T560 never actually turns off,
the only difference is that it's in SST mode at the start of the resume
process, so it's unclear as to why it would need so much time to come
back up.
There's been a discussion on this issue going on for a while on the
intel-gfx mailing list about this that has, in addition to including
developers from Intel, also had the correspondence of one of the
hardware engineers for Intel:
http://www.spinics.net/lists/intel-gfx/msg88831.html
http://www.spinics.net/lists/intel-gfx/msg88410.html
We've already looked into a couple of possible explanations for the
problem:
- Calling intel_dp_mst_resume() before right fix.
intel_runtime_pm_enable_interrupts(). This was the first fix I tried,
and while it worked it definitely wasn't the right fix. This worked
because DP aux transactions don't actually require interrupts to work:
static uint32_t
intel_dp_aux_wait_done(struct intel_dp *intel_dp, bool has_aux_irq)
{
struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
struct drm_device *dev = intel_dig_port->base.base.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
i915_reg_t ch_ctl = intel_dp->aux_ch_ctl_reg;
uint32_t status;
bool done;
#define C (((status = I915_READ_NOTRACE(ch_ctl)) & DP_AUX_CH_CTL_SEND_BUSY) == 0)
if (has_aux_irq)
done = wait_event_timeout(dev_priv->gmbus_wait_queue, C,
msecs_to_jiffies_timeout(10));
else
done = wait_for_atomic(C, 10) == 0;
if (!done)
DRM_ERROR("dp aux hw did not signal timeout (has irq: %i)!\n",
has_aux_irq);
#undef C
return status;
}
When there's no interrupts enabled, we end up timing out on the
wait_event_timeout() call, which causes us to check the DP status
register once to see if the transaction was successful or not. Since
this adds a 10ms delay to each aux transaction, it ends up adding a
long enough delay to the resume process for aux transactions to become
functional again. This gave us the illusion that enabling interrupts
had something to do with making things work again, and put me on the
wrong track for a while.
- Interrupts occurring when we try to perform the aux transactions
required to put the dock back into MST mode. This isn't the problem,
as the only interrupts I've observed that come during this timeout
period are from the snd_hda_intel driver, and disabling that driver
doesn't appear to change the behavior at all.
- Skylake's PSR block causing issues by performing aux transactions
while we try to bring the dock out of MST mode. Disabling PSR through
i915's command line options doesn't seem to change the behavior
either, nor does preventing the DMC firmware from being loaded.
Since this investigation went on for about 2 weeks, we decided it would
be better for the time being to just workaround this issue by making
sure AUX transactions wait a short period of time before retrying.
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460559513-32280-3-git-send-email-cpaul@redhat.com
|
|
This is part of a patch series to migrate all of the workarounds for
commonly seen behavior from bad sinks in intel_dp_dpcd_read_wake() to
drm's DP helper.
Some sinks need some time during the process of resuming the system from
sleep before they're ready to handle transactions. While it would be
nice if they responded with NACKs in these scenarios, this isn't always
the case as a few sinks will just timeout on all of the transactions
they receive until they're ready.
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460559513-32280-2-git-send-email-cpaul@redhat.com
|
|
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
|
|
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
|
|
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
|
|
Remove dev local and use to_i915() in gen8_ppgtt_notify_vgt.
v2: use dev_priv directly for QUESTION_MACROS (Joonas Lahtinen)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461323365-21256-1-git-send-email-matthew.auld@intel.com
|
|
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
|
|
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
|
|
Atm, we run the BSpec display core uninit/init sequences twice during
system suspend/resume. While this shouldn't cause any problem, it's
redundant, so get rid of the duplicate call.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-3-git-send-email-imre.deak@intel.com
|
|
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
No functional change.
CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com
|
|
Since ref counting is in the object now we can just call the
normal interfaces.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reduces the fb_lock to just protecting the num_fb/fb_list.
"Previously fb refcounting, and especially the weak reference
(kref_get_unless_zero) used in fb lookups have been protected by fb_lock.
But with the refactoring to share refcounting in the drm_mode_object base
class that switched to being protected by idr_mutex, which means fb_lock
critical sections can be reduced."
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When we lookup an ref counted object we now take a proper reference
using kref_get_unless_zero.
Framebuffer lookup no longer needs do this itself.
Convert rmfb to using framebuffer lookup and deal with the fact
it now gets an extra reference that we have to cleanup. This should
mean we can avoid holding fb_lock across rmfb. (if I'm wrong let me
know).
We also now only hold the fbs_lock around the list manipulation.
"Previously fb refcounting, and especially the weak reference
(kref_get_unless_zero) used in fb lookups have been protected by fb_lock.
But with the refactoring to share refcounting in the drm_mode_object base
class that switched to being protected by idr_mutex, which means fb_lock
critical sections can be reduced."
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
No need to hold the lock while assigning the variable.
Daniel wrote:
"Not sure why exactly I put that under the lock, but the only thing that
can race here is rmfb while addfb2 is still doing it's thing, with a
correctly guess (easy to do since they're fully deterministic) fb_id."
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
into drm-fixes
Misc radeon and amdgpu bug fixes for 4.6.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
amdgpu/uvd: add uvd fw version for amdgpu
drm/amdgpu: forbid mapping of userptr bo through radeon device file
drm/radeon: forbid mapping of userptr bo through radeon device file
drm/amdgpu: bump the afmt limit for CZ, ST, Polaris
drm/amdgpu: use defines for CRTCs and AMFT blocks
drm/radeon: print a message if ATPX dGPU power control is missing
Revert "drm/radeon: disable runtime pm on PX laptops without dGPU power control"
drm/amdgpu/acp: fix resume on CZ systems with AZ audio
drm/radeon: add a quirk for a XFX R9 270X
drm/radeon: print pci revision as well as pci ids on driver load
drm/amdgpu: when suspending, if uvd/vce was running. need to cancel delay work.
drm/radeon: fix initial connector audio value
|
|
We don't need to hold the fb lock around the initialisation,
only around the list manipulaton.
So do the lock hold only around the register for now.
From Daniel:
Previously fb refcounting, and especially the weak reference
(kref_get_unless_zero) used in fb lookups have been protected by fb_lock.
But with the refactoring to share refcounting in the drm_mode_object base
class that switched to being protected by idr_mutex, which means fb_lock
critical sections can be reduced.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
No point have this code dupliated at this point, use the
_object_find code instead now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is the initial code to add references to some mode objects.
In the future we need to start reference counting connectors so
firstly I want to reorganise the code so the framebuffer ref counting
uses the same paths.
This patch shouldn't change any functionality, just moves the kref.
[airlied: move kerneldoc as well]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Avoids drivers knowing where the kref is stored.
[airlied: add kerneldoc]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Just use the generic function.
The main side effect of this is that the fb->base.id
is now protected by the idr mutex as well.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
A later patch will use it in framebuffer_init, and I want
to keep the diff cleaner.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This changes the code to handle being called multiple times without
side effects. The new names seems more suitable for what it does.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
transform feedback fix.
* 'linux-4.6' of git://github.com/skeggsb/linux:
drm/nouveau/gr/gf100: select a stream master to fixup tfb offset queries
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
Was previously always hardcoded to 0.
Signed-off-by: Sonny Jiang <sonny.jiang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).
This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.
So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).
This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.
So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes array overflow on these chips.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Prerequiste for the next patch which ups the limits.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
With the joys of things running concurrently, there's always a chance
that the port we get passed in drm_dp_payload_send_msg() isn't actually
valid anymore. Because of this, we need to make sure we validate the
reference to the port before we use it otherwise we risk running into
various race conditions. For instance, on the Dell MST monitor I have
here for testing, hotplugging it enough times causes us to kernel panic:
[drm:intel_mst_enable_dp] 1
[drm:drm_dp_update_payload_part2] payload 0 1
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00200000, dig 0x10101011, pins 0x00000020
[drm:intel_hpd_irq_handler] digital hpd port B - short
[drm:intel_dp_hpd_pulse] got hpd irq on port B - short
[drm:intel_dp_check_mst_status] got esi 00 10 00
[drm:drm_dp_update_payload_part2] payload 1 1
general protection fault: 0000 [#1] SMP
…
Call Trace:
[<ffffffffa012b632>] drm_dp_update_payload_part2+0xc2/0x130 [drm_kms_helper]
[<ffffffffa032ef08>] intel_mst_enable_dp+0xf8/0x180 [i915]
[<ffffffffa0310dbd>] haswell_crtc_enable+0x3ed/0x8c0 [i915]
[<ffffffffa030c84d>] intel_atomic_commit+0x5ad/0x1590 [i915]
[<ffffffffa01db877>] ? drm_atomic_set_crtc_for_connector+0x57/0xe0 [drm]
[<ffffffffa01dc4e7>] drm_atomic_commit+0x37/0x60 [drm]
[<ffffffffa0130a3a>] drm_atomic_helper_set_config+0x7a/0xb0 [drm_kms_helper]
[<ffffffffa01cc482>] drm_mode_set_config_internal+0x62/0x100 [drm]
[<ffffffffa01d02ad>] drm_mode_setcrtc+0x3cd/0x4e0 [drm]
[<ffffffffa01c18e3>] drm_ioctl+0x143/0x510 [drm]
[<ffffffffa01cfee0>] ? drm_mode_setplane+0x1b0/0x1b0 [drm]
[<ffffffff810f79a7>] ? hrtimer_start_range_ns+0x1b7/0x3a0
[<ffffffff81212962>] do_vfs_ioctl+0x92/0x570
[<ffffffff81590852>] ? __sys_recvmsg+0x42/0x80
[<ffffffff81212eb9>] SyS_ioctl+0x79/0x90
[<ffffffff816b4e32>] entry_SYSCALL_64_fastpath+0x1a/0xa4
RIP [<ffffffffa012b026>] drm_dp_payload_send_msg+0x146/0x1f0 [drm_kms_helper]
Which occurs because of the hotplug event shown in the log, which ends
up causing DRM's dp helpers to drop the port we're updating the payload
on and panic.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Single nouveau regression fix
* 'linux-4.6' of git://github.com/skeggsb/linux:
drm/nouveau/kms: fix setting of default values for dithering properties
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
