| Age | Commit message (Collapse) | Author |
|---|
|
We need to explicitly set the TLB Request Timer initial value in the
BW_BUDDY registers to 0x8 rather than relying on the hardware default.
v2: Apply missing REG_FIELD_PREP to ensure 0x8 is placed in the correct
bits during the rmw. (Jose)
Bspec: 52890
Bspec: 50044
Fixes: 3fa01d642fa7 ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200219215655.2923650-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 87e04f75928bb5d357ef7df4eedc1a7e2761a833)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228004320.127142-2-matthew.d.roper@intel.com
|
|
It wasn't terribly clear from the bspec's wording, but after discussion
with the hardware folks, it turns out that we need to preserve the
pre-existing contents of the MBUS ABOX control register when
initializing a few specific bits.
Bspec: 49213
Bspec: 50096
Fixes: 4cb4585e5a7f ("drm/i915/icl: initialize MBus during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204011032.582737-1-matthew.d.roper@intel.com
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
(cherry picked from commit 837b63e6087838d0f1e612d448405419199d8033)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228004320.127142-1-matthew.d.roper@intel.com
|
|
Commit 60c6a14b489b ("drm/i915/display: Force the state compute phase
once to enable PSR") was forcing the state compute too earlier
causing errors because not everything was initialized, so here
moving to the end of i915_driver_modeset_probe() when the display is
all initialized.
Also fixing the place where it disarm the force probe as during the
atomic check phase errors could happen like the ones due locking and
it would cause PSR to never be enabled if that happens.
Leaving the disarm to the atomic commit phase, intel_psr_enable() or
intel_psr_update() will be called even if the current state do not
allow PSR to be enabled.
v2: Check if intel_dp is null in intel_psr_force_mode_changed_set()
v3: Check intel_dp before get dev_priv
v4:
- renamed intel_psr_force_mode_changed_set() to
intel_psr_set_force_mode_changed()
- removed the set parameter from intel_psr_set_force_mode_changed()
- not calling intel_psr_set_force_mode_changed() from
intel_psr_enable/update(), directly setting it after the same checks
that intel_psr_set_force_mode_changed() does
- moved intel_psr_set_force_mode_changed() arm call to
i915_driver_modeset_probe() as it is a better for a PSR call, all the
functions calls happening between the old and the new function call
will cause issue
[backported to v5.6-rc3]
Fixes: 60c6a14b489b ("drm/i915/display: Force the state compute phase once to enable PSR")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1151
Tested-by: Ross Zwisler <zwisler@google.com>
Reported-by: Ross Zwisler <zwisler@google.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221212635.11614-1-jose.souza@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20200227205540.126135-1-jose.souza@intel.com
(cherry picked from commit df1a5bfc16f3275a74f77d73375e69bc62c45c4b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Call cond_resched() between each freed object in case we have a really,
really long list, and we don't want to block normal processes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221100953.2587176-1-chris@chris-wilson.co.uk
(cherry picked from commit deeee411a97559096523f97655ff16da34cf0573)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The qxl driver uses an empty implementation for its encoder. Replace
the code with the generic simple encoder.
v4:
* handle errors returned from drm_simple_encoder_init()
v2:
* rebase onto new simple-encoder interface
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228081828.18463-5-tzimmermann@suse.de
|
|
The mgag200 driver uses an empty implementation for its encoder. Replace
the code with the generic simple encoder.
v4:
* print error message with drm_err()
v3:
* init pre-allocated encoder with drm_simple_encoder_init()
v2:
* rebase onto new simple-encoder interface
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228081828.18463-4-tzimmermann@suse.de
|
|
The ast driver uses an empty implementation for its encoder. Replace
the code with the generic simple encoder.
v2:
* rebase onto new simple-encoder interface
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228081828.18463-3-tzimmermann@suse.de
|
|
This patch makes the internal encoder implementation of the simple
KMS helpers available to drivers.
These simple-encoder helpers initialize an encoder with an empty
implementation. This covers the requirements of most of the existing
DRM drivers. A call to drm_simple_encoder_create() allocates and
initializes an encoder instance, a call to drm_simple_encoder_init()
initializes a pre-allocated instance.
v3:
* remove drm_simple_encoder_create(); not required yet
* provide more precise documentation
v2:
* move simple encoder to KMS helpers
* remove name argument; simplifies implementation
* don't allocate with devm_ interfaces; unsafe with DRM
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228081828.18463-2-tzimmermann@suse.de
|
|
Was added by commit 95cf9264d5f3 ("x86, drm, fbdev: Do not specify
encrypted memory for video mappings"), then it was kept through various
changes.
While vram actually needs decrypted mappings this is not correct for
shmem gem objects which live in main memory not io memory, so remove the
call.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200228104723.18757-1-kraxel@redhat.com
|
|
Move enabling and disabling HDMI_EN optional regulator to probe() function
to keep track on the regulator status. This fixes following warning if
probe() fails (for example when I2C DDC adapter cannot be yet gathered
due to the missing driver). This fixes following warning observed on
Arndale5250 board with multi_v7_defconfig:
[drm] Failed to get ddc i2c adapter by node
------------[ cut here ]------------
WARNING: CPU: 0 PID: 214 at drivers/regulator/core.c:2051 _regulator_put+0x16c/0x184
Modules linked in: ...
CPU: 0 PID: 214 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219-00040-g38af1dfafdbb #7570
Hardware name: Samsung Exynos (Flattened Device Tree)
[<c0312258>] (unwind_backtrace) from [<c030cc10>] (show_stack+0x10/0x14)
[<c030cc10>] (show_stack) from [<c0f0d3a0>] (dump_stack+0xcc/0xe0)
[<c0f0d3a0>] (dump_stack) from [<c0346a58>] (__warn+0xe0/0xf8)
[<c0346a58>] (__warn) from [<c0346b20>] (warn_slowpath_fmt+0xb0/0xb8)
[<c0346b20>] (warn_slowpath_fmt) from [<c0893f58>] (_regulator_put+0x16c/0x184)
[<c0893f58>] (_regulator_put) from [<c0893f8c>] (regulator_put+0x1c/0x2c)
[<c0893f8c>] (regulator_put) from [<c09b2664>] (release_nodes+0x17c/0x200)
[<c09b2664>] (release_nodes) from [<c09aebe8>] (really_probe+0x10c/0x350)
[<c09aebe8>] (really_probe) from [<c09aefa8>] (driver_probe_device+0x60/0x1a0)
[<c09aefa8>] (driver_probe_device) from [<c09af288>] (device_driver_attach+0x58/0x60)
[<c09af288>] (device_driver_attach) from [<c09af310>] (__driver_attach+0x80/0xbc)
[<c09af310>] (__driver_attach) from [<c09ace34>] (bus_for_each_dev+0x68/0xb4)
[<c09ace34>] (bus_for_each_dev) from [<c09ae00c>] (bus_add_driver+0x130/0x1e8)
[<c09ae00c>] (bus_add_driver) from [<c09afd98>] (driver_register+0x78/0x110)
[<c09afd98>] (driver_register) from [<bf139558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf139558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dc02c>] (do_init_module+0x60/0x210)
[<c03dc02c>] (do_init_module) from [<c03daf44>] (load_module+0x1c0c/0x2310)
[<c03daf44>] (load_module) from [<c03db85c>] (sys_finit_module+0xac/0xbc)
[<c03db85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xecca3fa8 to 0xecca3ff0)
...
---[ end trace 276c91214635905c ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Writing to the built-in strings arrays doesn't work if driver is loaded
as kernel module. This is also considered as a bad pattern. Fix this by
adding a call to clk_get() with legacy clock name. This fixes following
kernel oops if driver is loaded as module:
Unable to handle kernel paging request at virtual address bf047978
pgd = (ptrval)
[bf047978] *pgd=59344811, *pte=5903c6df, *ppte=5903c65f
Internal error: Oops: 80f [#1] SMP ARM
Modules linked in: mc exynosdrm(+) analogix_dp rtc_s3c exynos_ppmu i2c_gpio
CPU: 1 PID: 212 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200219 #326
videodev: Linux video capture interface: v2.00
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at exynos_dsi_probe+0x1f0/0x384 [exynosdrm]
LR is at exynos_dsi_probe+0x1dc/0x384 [exynosdrm]
...
Process systemd-udevd (pid: 212, stack limit = 0x(ptrval))
...
[<bf03cf14>] (exynos_dsi_probe [exynosdrm]) from [<c09b1ca0>] (platform_drv_probe+0x6c/0xa4)
[<c09b1ca0>] (platform_drv_probe) from [<c09afcb8>] (really_probe+0x210/0x350)
[<c09afcb8>] (really_probe) from [<c09aff74>] (driver_probe_device+0x60/0x1a0)
[<c09aff74>] (driver_probe_device) from [<c09b0254>] (device_driver_attach+0x58/0x60)
[<c09b0254>] (device_driver_attach) from [<c09b02dc>] (__driver_attach+0x80/0xbc)
[<c09b02dc>] (__driver_attach) from [<c09ade00>] (bus_for_each_dev+0x68/0xb4)
[<c09ade00>] (bus_for_each_dev) from [<c09aefd8>] (bus_add_driver+0x130/0x1e8)
[<c09aefd8>] (bus_add_driver) from [<c09b0d64>] (driver_register+0x78/0x110)
[<c09b0d64>] (driver_register) from [<bf038558>] (exynos_drm_init+0xe8/0x11c [exynosdrm])
[<bf038558>] (exynos_drm_init [exynosdrm]) from [<c0302fa8>] (do_one_initcall+0x50/0x220)
[<c0302fa8>] (do_one_initcall) from [<c03dd02c>] (do_init_module+0x60/0x210)
[<c03dd02c>] (do_init_module) from [<c03dbf44>] (load_module+0x1c0c/0x2310)
[<c03dbf44>] (load_module) from [<c03dc85c>] (sys_finit_module+0xac/0xbc)
[<c03dc85c>] (sys_finit_module) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xd979bfa8 to 0xd979bff0)
...
---[ end trace db16efe05faab470 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Properly propagate error value from devm_regulator_bulk_get() and don't
confuse user with meaningless warning about failure in getting regulators
in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The panel-dpi compatible is a fallback that
allows the DT to specify the timing.
When matching panel-dpi expect the device tree to include the
timing information for the display-panel.
Background for this change:
There are a lot of panels and new models hits the market very often.
It is a lost cause trying to chase them all and users of new panels
will often find them in situations that the panel they ues are not
supported by the kernel.
On top of this a lot of panels are customized based on customer
specifications.
Including the panel timing in the device tree allows for a simple
way to describe the actual HW and use this description in a generic
way in the kernel.
This allows uses of proprietary panels, or panels which are not
included in the kernel, to specify the timing in the device tree
together with all the other HW descriptions.
And thus, using the device tree it is then easy to add support
for an otherwise unknown panel.
The current support expect panels that do not require any
delays for prepare/enable/disable/unprepare.
Oleksandr Suvorov replied:
I've just tested this patch on Apalis iMX6Q and Colibri iMX7D using
panel settings from the following patch:
https://lore.kernel.org/linux-arm-kernel/20200115123401.2264293-4-oleksandr.suvorov@toradex.com/
It works for me, thanks!
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tested-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200216181513.28109-6-sam@ravnborg.org
|
|
This adds a driver for panels based on the Novatek NT35510
display driver IC, such as the Hydis HVA40WV1 panel found
in the Samsung GT-S7710.
The NT35510 can be used with both internal and external
backlight (such as GPIO backlight) so we support both:
if no external backlight is found, we register a subdriver
for the internal backlight.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200223121841.26836-3-linus.walleij@linaro.org
|
|
There is an integer overflow when we round up to PAGE_SIZE, but it's
harmless because we never re-use "request->size" for anything meaningful.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228092321.axulddmkxrujkmas@kili.mountain
|
|
Contributors for this file are :
Chris Wilson <chris@chris-wilson.co.uk>
Denis Efremov <efremov@linux.com>
Jani Nikula <jani.nikula@intel.com>
Maxime Ripard <mripard@kernel.org>
Noralf Trønnes <noralf@tronnes.org>
Sam Ravnborg <sam@ravnborg.org>
Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Denis Efremov <efremov@linux.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Emmanuel Vadot <manu@FreeBSD.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200215180911.18299-2-manu@FreeBSD.org
|
|
We monitor the health of the system via periodic heartbeat pulses. The
pulses also provide the opportunity to perform garbage collection.
However, we interpret an incomplete pulse (a missed heartbeat) as an
indication that the system is no longer responsive, i.e. hung, and
perform an engine or full GPU reset. Given that the preemption
granularity can be very coarse on a system, we let the sysadmin override
our legacy timeouts which were "optimised" for desktop applications.
The heartbeat interval can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/heartbeat_interval_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-7-chris@chris-wilson.co.uk
|
|
After initialising a preemption request, we give the current resident a
small amount of time to vacate the GPU. The preemption request is for a
higher priority context and should be immediate to maintain high
quality of service (and avoid priority inversion). However, the
preemption granularity of the GPU can be quite coarse and so we need a
compromise.
The preempt timeout can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/preempt_timeout_ms
and can be disabled by setting it to 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-6-chris@chris-wilson.co.uk
|
|
When we allow ourselves to sleep before a GPU reset after disabling
submission, even for a few milliseconds, gives an innocent context the
opportunity to clear the GPU before the reset occurs. However, how long
to sleep depends on the typical non-preemptible duration (a similar
problem to determining the ideal preempt-reset timeout or even the
heartbeat interval). As this seems of a hard policy decision, punt it to
userspace.
The timeout can be adjusted using
/sys/class/drm/card?/engine/*/stop_timeout_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-5-chris@chris-wilson.co.uk
|
|
We busywait on an inflight request (one that is currently executing on
HW, and so might complete quickly) prior to setting up an interrupt and
sleeping. The trade off is that we keep an expensive CPU core busy in
order to avoid wake up latency: where that trade off should lie is best
left to the sysadmin.
The busywait mechanism can be compiled out with
./scripts/config --set-val DRM_I915_SPIN_REQUEST 0
The maximum busywait duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/ms_busywait_duration_ns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-4-chris@chris-wilson.co.uk
|
|
Execlists uses a scheduling quantum (a timeslice) to alternate execution
between ready-to-run contexts of equal priority. This ensures that all
users (though only if they of equal importance) have the opportunity to
run and prevents livelocks where contexts may have implicit ordering due
to userspace semaphores.
The timeslicing mechanism can be compiled out with
./scripts/config --set-val DRM_I915_TIMESLICE_DURATION 0
The timeslice duration can be adjusted per-engine using,
/sys/class/drm/card?/engine/*/timeslice_duration_ms
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-3-chris@chris-wilson.co.uk
|
|
Use the per-engine sysfs directory to let userspace discover the
mmio_base of each engine. Prior to recent generations, the user
accessible registers on each engine are at a fixed offset relative to
each engine -- but require absolute addressing. As the absolute address
depends on the actual physical engine, this is not always possible to
determine from userspace (for example icl may expose vcs1 or vcs2 as the
second vcs engine). Make this easy for userspace to discover by
providing the mmio_base in sysfs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-2-chris@chris-wilson.co.uk
|
|
Preliminary stub to add engines underneath /sys/class/drm/cardN/, so
that we can expose properties on each engine to the sysadmin.
To start with we have basic analogues of the i915_query ioctl so that we
can pretty print engine discovery from the shell, and flesh out the
directory structure. Later we will add writeable sysadmin properties such
as per-engine timeout controls.
An example tree of the engine properties on Braswell:
/sys/class/drm/card0
└── engine
├── bcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── rcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
├── vcs0
│ ├── capabilities
│ ├── class
│ ├── instance
│ ├── known_capabilities
│ └── name
└── vecs0
├── capabilities
├── class
├── instance
├── known_capabilities
└── name
v2: Include stringified capabilities
v3: Include all known capabilities for futureproofing.
v4: Combine the two caps loops into one
v5: Hide underneath Kconfig.unstable for wider discussion
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Steve Carbonari <steven.carbonari@intel.com>
Reviewed-by: Steve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-1-chris@chris-wilson.co.uk
|
|
This adds a message lock to the smu_send_smc_msg* implementations to
protect against concurrent access to the mmu registers used to
communicate with the SMU
v2: Implement for smu_v12_0 as well
v3: Add mutex_init for message_lock
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The new interface reads the argument in the call to send the message, so
this is no longer needed, and shouldn't be used for concurrency safety
reasons.
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move the responsibility for reading argument registers into the
smu_send_smc_msg* implementations, so that adding a message-sending lock
to protect the SMU registers will result in the lock still being held
when the argument is read.
v2: transition smu_v12_0, it's asics, and vega20
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
smu during boot up
dc to pplib interface is changed for navi1x, renoir.
display_config_changed is not called by dc anymore.
smu_write_watermarks_table is not executed for navi1x, renoir
during boot up.
solution: call smu_write_watermarks_table just after dc pass
watermark clock settings to pplib
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If we release drm_device before amdgpu_driver_unload_kms,
then it will raise the error below. Therefore, we need to
place it before amdgpu_driver_unload_kms.
[ 43.055736] Memory manager not clean during takedown.
[ 43.055777] WARNING: CPU: 1 PID: 2807 at /build/linux-hwe-9KJ07q/linux-hwe-4.18.0/drivers/gpu/drm/drm_mm.c:913 drm_mm_takedown+0x24/0x30 [drm]
[ 43.055778] Modules linked in: amdgpu(OE-) amd_sched(OE) amdttm(OE) amdkcl(OE) amd_iommu_v2 drm_kms_helper drm i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt snd_hda_codec_generic nfit kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_pcm ghash_clmulni_intel snd_seq_midi snd_seq_midi_event pcbc snd_rawmidi snd_seq snd_seq_device aesni_intel snd_timer joydev aes_x86_64 crypto_simd cryptd glue_helper snd soundcore input_leds mac_hid serio_raw qemu_fw_cfg binfmt_misc sch_fq_codel nfsd auth_rpcgss nfs_acl lockd grace sunrpc parport_pc ppdev lp parport ip_tables x_tables autofs4 hid_generic floppy usbhid psmouse hid i2c_piix4 e1000 pata_acpi
[ 43.055819] CPU: 1 PID: 2807 Comm: modprobe Tainted: G OE 4.18.0-15-generic #16~18.04.1-Ubuntu
[ 43.055820] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
[ 43.055830] RIP: 0010:drm_mm_takedown+0x24/0x30 [drm]
[ 43.055831] Code: 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 47 38 48 83 c7 38 48 39 c7 75 02 f3 c3 55 48 c7 c7 38 33 80 c0 48 89 e5 e8 1c 41 ec d0 <0f> 0b 5d c3 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
[ 43.055857] RSP: 0018:ffffae33c1393d28 EFLAGS: 00010286
[ 43.055859] RAX: 0000000000000000 RBX: ffff9651b4a29800 RCX: 0000000000000006
[ 43.055860] RDX: 0000000000000007 RSI: 0000000000000096 RDI: ffff9651bfc964b0
[ 43.055861] RBP: ffffae33c1393d28 R08: 00000000000002a6 R09: 0000000000000004
[ 43.055861] R10: ffffae33c1393d20 R11: 0000000000000001 R12: ffff9651ba6cb000
[ 43.055863] R13: ffff9651b7f40000 R14: ffffffffc0de3a10 R15: ffff9651ba5c6460
[ 43.055864] FS: 00007f1d3c08d540(0000) GS:ffff9651bfc80000(0000) knlGS:0000000000000000
[ 43.055865] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 43.055866] CR2: 00005630a5831640 CR3: 000000012e274004 CR4: 00000000003606e0
[ 43.055870] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 43.055871] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 43.055871] Call Trace:
[ 43.055885] drm_vma_offset_manager_destroy+0x1b/0x30 [drm]
[ 43.055894] drm_gem_destroy+0x19/0x40 [drm]
[ 43.055903] drm_dev_fini+0x7f/0x90 [drm]
[ 43.055911] drm_dev_release+0x2b/0x40 [drm]
[ 43.055919] drm_dev_unplug+0x64/0x80 [drm]
[ 43.055994] amdgpu_pci_remove+0x39/0x70 [amdgpu]
[ 43.055998] pci_device_remove+0x3e/0xc0
[ 43.056001] device_release_driver_internal+0x18a/0x260
[ 43.056003] driver_detach+0x3f/0x80
[ 43.056004] bus_remove_driver+0x59/0xd0
[ 43.056006] driver_unregister+0x2c/0x40
[ 43.056008] pci_unregister_driver+0x22/0xa0
[ 43.056087] amdgpu_exit+0x15/0x57c [amdgpu]
[ 43.056090] __x64_sys_delete_module+0x146/0x280
[ 43.056094] do_syscall_64+0x5a/0x120
v2: put drm_dev_put after pci_set_drvdata
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
drm_minor_unregister will invoke drm_debugfs_cleanup
to clean all the child node under primary minor node.
We don't need to invoke amdgpu_debugfs_fini and
amdgpu_debugfs_regs_cleanup to clean agian.
Otherwise, it will raise the NULL pointer like below.
[ 45.046029] BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8
[ 45.047256] PGD 0 P4D 0
[ 45.047713] Oops: 0002 [#1] SMP PTI
[ 45.048198] CPU: 0 PID: 2796 Comm: modprobe Tainted: G W OE 4.18.0-15-generic #16~18.04.1-Ubuntu
[ 45.049538] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
[ 45.050651] RIP: 0010:down_write+0x1f/0x40
[ 45.051194] Code: 90 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 53 48 89 fb e8 ce d9 ff ff 48 ba 01 00 00 00 ff ff ff ff 48 89 d8 <f0> 48 0f c1 10 85 d2 74 05 e8 53 1c ff ff 65 48 8b 04 25 00 5c 01
[ 45.053702] RSP: 0018:ffffad8f4133fd40 EFLAGS: 00010246
[ 45.054384] RAX: 00000000000000a8 RBX: 00000000000000a8 RCX: ffffa011327dd814
[ 45.055349] RDX: ffffffff00000001 RSI: 0000000000000001 RDI: 00000000000000a8
[ 45.056346] RBP: ffffad8f4133fd48 R08: 0000000000000000 R09: ffffffffc0690a00
[ 45.057326] R10: ffffad8f4133fd58 R11: 0000000000000001 R12: ffffa0113cff0300
[ 45.058266] R13: ffffa0113c0a0000 R14: ffffffffc0c02a10 R15: ffffa0113e5c7860
[ 45.059221] FS: 00007f60d46f9540(0000) GS:ffffa0113fc00000(0000) knlGS:0000000000000000
[ 45.060809] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 45.061826] CR2: 00000000000000a8 CR3: 0000000136250004 CR4: 00000000003606f0
[ 45.062913] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 45.064404] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 45.065897] Call Trace:
[ 45.066426] debugfs_remove+0x36/0xa0
[ 45.067131] amdgpu_debugfs_ring_fini+0x15/0x20 [amdgpu]
[ 45.068019] amdgpu_debugfs_fini+0x2c/0x50 [amdgpu]
[ 45.068756] amdgpu_pci_remove+0x49/0x70 [amdgpu]
[ 45.069439] pci_device_remove+0x3e/0xc0
[ 45.070037] device_release_driver_internal+0x18a/0x260
[ 45.070842] driver_detach+0x3f/0x80
[ 45.071325] bus_remove_driver+0x59/0xd0
[ 45.071850] driver_unregister+0x2c/0x40
[ 45.072377] pci_unregister_driver+0x22/0xa0
[ 45.073043] amdgpu_exit+0x15/0x57c [amdgpu]
[ 45.073683] __x64_sys_delete_module+0x146/0x280
[ 45.074369] do_syscall_64+0x5a/0x120
[ 45.074916] entry_SYSCALL_64_after_hwframe+0x44/0xa9
v2: remove all debugfs cleanup/fini code at amdgpu
v3: squash in unused variable removal
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SPM_VMID is a global resource, SPM access the video memory according to
SPM_VMID. The initial valude of SPM_VMID is 0 which is used by kernel.
That means UMD can overwrite the memory of VMID0 by enabling SPM, that
is really dangerous.
Initialize SPM_VMID with 0xf, it messes up other user mode process at
most.
v2: squash in indentation fix
Signed-off-by: Jacob He <jacob.he@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For vega10 sriov, the register is blocked, use
copy data command to fix the issue.
v2: Rename amdgpu_kiq_read_clock to gfx_v9_0_kiq_read_clock.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
SDMA MQD memory type is NC that causes MQD data overwritten
accidentally by an old stable cache line. Changing it to UC
default for GART will fix the issue.
The mqd_gfx9 parameter is meant for control stacks that are
allocated together with user mode queue MQDs. Setting
mqd_gfx9 to true maps the control stack pages as NC.
Here it was accidentally applied to SDMA MQDs,
which are allocated together with the HIQ MQD. Setting
the mqd_gfx9 to false avoids that.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Given we can query all the asic specific information from amdgpu_gfx_config,
we can make get_tile_config() generic.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The two members will be used by KFD later.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The assert_mmap_offset() returns type bool so if we return an error
pointer that is "return true;" or success. If we have an error, then
we should return false.
Fixes: 3d81d589d6e3 ("drm/i915: Test exhaustion of the mmap space")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228141413.qfjf4abr323drlo4@kili.mountain
|
|
WaDDIIOTimeout is only for A1 (pre-prod) glk steppings. Nuke it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
TGL+ supposedly do not need Wa_1405510057 so limit it to
gen11 only.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
w/a #1139 is only needed for pre-production GLK. Nuke it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
An odd and highly unlikely path caught us out. On delayed submission
(due to an asynchronous reset handler), we poked the priority_hint and
kicked the tasklet. However, we had already marked the device as wedged
and swapped out the tasklet for a no-op. The result was that we never
cleared the priority hint and became upset when we later checked.
<0> [574.303565] i915_sel-6278 2.... 481822445us : __i915_subtests: Running intel_execlists_live_selftests/live_error_interrupt
<0> [574.303565] i915_sel-6278 2.... 481822472us : __engine_unpark: 0000:00:02.0 rcs0:
<0> [574.303565] i915_sel-6278 2.... 481822491us : __gt_unpark: 0000:00:02.0
<0> [574.303565] i915_sel-6278 2.... 481823220us : execlists_context_reset: 0000:00:02.0 rcs0: context:f4ee reset
<0> [574.303565] i915_sel-6278 2.... 481824830us : __intel_context_active: 0000:00:02.0 rcs0: context:f51b active
<0> [574.303565] i915_sel-6278 2.... 481825258us : __intel_context_do_pin: 0000:00:02.0 rcs0: context:f51b pin ring:{start:00006000, head:0000, tail:0000}
<0> [574.303565] i915_sel-6278 2.... 481825311us : __i915_request_commit: 0000:00:02.0 rcs0: fence f51b:2, current 0
<0> [574.303565] i915_sel-6278 2d..1 481825347us : __i915_request_submit: 0000:00:02.0 rcs0: fence f51b:2, current 0
<0> [574.303565] i915_sel-6278 2d..1 481825363us : trace_ports: 0000:00:02.0 rcs0: submit { f51b:2, 0:0 }
<0> [574.303565] i915_sel-6278 2.... 481826809us : __intel_context_active: 0000:00:02.0 rcs0: context:f51c active
<0> [574.303565] <idle>-0 7d.h2 481827326us : cs_irq_handler: 0000:00:02.0 rcs0: CS error: 1
<0> [574.303565] <idle>-0 7..s1 481827377us : process_csb: 0000:00:02.0 rcs0: cs-irq head=3, tail=4
<0> [574.303565] <idle>-0 7..s1 481827379us : process_csb: 0000:00:02.0 rcs0: csb[4]: status=0x10000001:0x00000000
<0> [574.305593] <idle>-0 7..s1 481827385us : trace_ports: 0000:00:02.0 rcs0: promote { f51b:2*, 0:0 }
<0> [574.305611] <idle>-0 7..s1 481828179us : execlists_reset: 0000:00:02.0 rcs0: reset for CS error
<0> [574.305611] i915_sel-6278 2.... 481828284us : __intel_context_do_pin: 0000:00:02.0 rcs0: context:f51c pin ring:{start:00007000, head:0000, tail:0000}
<0> [574.305611] i915_sel-6278 2.... 481828345us : __i915_request_commit: 0000:00:02.0 rcs0: fence f51c:2, current 0
<0> [574.305611] <idle>-0 7dNs2 481847823us : __i915_request_unsubmit: 0000:00:02.0 rcs0: fence f51b:2, current 1
<0> [574.305611] <idle>-0 7dNs2 481847857us : execlists_hold: 0000:00:02.0 rcs0: fence f51b:2, current 1 on hold
<0> [574.305611] <idle>-0 7.Ns1 481847863us : intel_engine_reset: 0000:00:02.0 rcs0: flags=4
<0> [574.305611] <idle>-0 7.Ns1 481847945us : execlists_reset_prepare: 0000:00:02.0 rcs0: depth<-1
<0> [574.305611] <idle>-0 7.Ns1 481847946us : intel_engine_stop_cs: 0000:00:02.0 rcs0:
<0> [574.305611] <idle>-0 7.Ns1 538584284us : intel_engine_stop_cs: 0000:00:02.0 rcs0: timed out on STOP_RING -> IDLE
<0> [574.305611] <idle>-0 7.Ns1 538584347us : __intel_gt_reset: 0000:00:02.0 engine_mask=1
<0> [574.305611] <idle>-0 7.Ns1 538584406us : execlists_reset_rewind: 0000:00:02.0 rcs0:
<0> [574.305611] <idle>-0 7dNs2 538585050us : __i915_request_reset: 0000:00:02.0 rcs0: fence f51b:2, current 1 guilty? yes
<0> [574.305611] <idle>-0 7dNs2 538585063us : __execlists_reset: 0000:00:02.0 rcs0: replay {head:0000, tail:0068}
<0> [574.306565] <idle>-0 7.Ns1 538588457us : intel_engine_cancel_stop_cs: 0000:00:02.0 rcs0:
<0> [574.306565] <idle>-0 7dNs2 538588462us : __i915_request_submit: 0000:00:02.0 rcs0: fence f51c:2, current 0
<0> [574.306565] <idle>-0 7dNs2 538588471us : trace_ports: 0000:00:02.0 rcs0: submit { f51c:2, 0:0 }
<0> [574.306565] <idle>-0 7.Ns1 538588474us : execlists_reset_finish: 0000:00:02.0 rcs0: depth->1
<0> [574.306565] kworker/-202 2.... 538588755us : i915_request_retire: 0000:00:02.0 rcs0: fence f51c:2, current 2
<0> [574.306565] ksoftirq-46 7..s. 538588773us : process_csb: 0000:00:02.0 rcs0: cs-irq head=11, tail=1
<0> [574.306565] ksoftirq-46 7..s. 538588774us : process_csb: 0000:00:02.0 rcs0: csb[0]: status=0x10000001:0x00000000
<0> [574.306565] ksoftirq-46 7..s. 538588776us : trace_ports: 0000:00:02.0 rcs0: promote { f51c:2!, 0:0 }
<0> [574.306565] ksoftirq-46 7..s. 538588778us : process_csb: 0000:00:02.0 rcs0: csb[1]: status=0x10000018:0x00000020
<0> [574.306565] ksoftirq-46 7..s. 538588779us : trace_ports: 0000:00:02.0 rcs0: completed { f51c:2!, 0:0 }
<0> [574.306565] kworker/-202 2.... 538588826us : intel_context_unpin: 0000:00:02.0 rcs0: context:f51c unpin
<0> [574.306565] i915_sel-6278 6.... 538589663us : __intel_gt_set_wedged.part.32: 0000:00:02.0 start
<0> [574.306565] i915_sel-6278 6.... 538589667us : execlists_reset_prepare: 0000:00:02.0 rcs0: depth<-0
<0> [574.306565] i915_sel-6278 6.... 538589710us : intel_engine_stop_cs: 0000:00:02.0 rcs0:
<0> [574.306565] i915_sel-6278 6.... 538589732us : execlists_reset_prepare: 0000:00:02.0 bcs0: depth<-0
<0> [574.307591] i915_sel-6278 6.... 538589733us : intel_engine_stop_cs: 0000:00:02.0 bcs0:
<0> [574.307591] i915_sel-6278 6.... 538589757us : execlists_reset_prepare: 0000:00:02.0 vcs0: depth<-0
<0> [574.307591] i915_sel-6278 6.... 538589758us : intel_engine_stop_cs: 0000:00:02.0 vcs0:
<0> [574.307591] i915_sel-6278 6.... 538589771us : execlists_reset_prepare: 0000:00:02.0 vcs1: depth<-0
<0> [574.307591] i915_sel-6278 6.... 538589772us : intel_engine_stop_cs: 0000:00:02.0 vcs1:
<0> [574.307591] i915_sel-6278 6.... 538589778us : execlists_reset_prepare: 0000:00:02.0 vecs0: depth<-0
<0> [574.307591] i915_sel-6278 6.... 538589780us : intel_engine_stop_cs: 0000:00:02.0 vecs0:
<0> [574.307591] i915_sel-6278 6.... 538589786us : __intel_gt_reset: 0000:00:02.0 engine_mask=ff
<0> [574.307591] i915_sel-6278 6.... 538591175us : execlists_reset_cancel: 0000:00:02.0 rcs0:
<0> [574.307591] i915_sel-6278 6.... 538591970us : execlists_reset_cancel: 0000:00:02.0 bcs0:
<0> [574.307591] i915_sel-6278 6.... 538591982us : execlists_reset_cancel: 0000:00:02.0 vcs0:
<0> [574.307591] i915_sel-6278 6.... 538591996us : execlists_reset_cancel: 0000:00:02.0 vcs1:
<0> [574.307591] i915_sel-6278 6.... 538592759us : execlists_reset_cancel: 0000:00:02.0 vecs0:
<0> [574.307591] i915_sel-6278 6.... 538592977us : execlists_reset_finish: 0000:00:02.0 rcs0: depth->0
<0> [574.307591] i915_sel-6278 6.N.. 538592996us : execlists_reset_finish: 0000:00:02.0 bcs0: depth->0
<0> [574.307591] i915_sel-6278 6.N.. 538593023us : execlists_reset_finish: 0000:00:02.0 vcs0: depth->0
<0> [574.307591] i915_sel-6278 6.N.. 538593037us : execlists_reset_finish: 0000:00:02.0 vcs1: depth->0
<0> [574.307591] i915_sel-6278 6.N.. 538593051us : execlists_reset_finish: 0000:00:02.0 vecs0: depth->0
<0> [574.307591] i915_sel-6278 6.... 538593407us : __intel_gt_set_wedged.part.32: 0000:00:02.0 end
<0> [574.307591] kworker/-210 7d..1 551958381us : execlists_unhold: 0000:00:02.0 rcs0: fence f51b:2, current 2 hold release
<0> [574.307591] i915_sel-6278 0.... 559490788us : i915_request_retire: 0000:00:02.0 rcs0: fence f51b:2, current 2
<0> [574.307591] i915_sel-6278 0.... 559490793us : intel_context_unpin: 0000:00:02.0 rcs0: context:f51b unpin
<0> [574.307591] i915_sel-6278 0.... 559490798us : __engine_park: 0000:00:02.0 rcs0: parked
<0> [574.307591] i915_sel-6278 0.... 559490982us : __intel_context_retire: 0000:00:02.0 rcs0: context:f51c retire runtime: { total:30004ns, avg:30004ns }
<0> [574.307591] i915_sel-6278 0.... 559491372us : __engine_park: __engine_park:261 GEM_BUG_ON(engine->execlists.queue_priority_hint != (-((int)(~0U >> 1)) - 1))
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-9-chris@chris-wilson.co.uk
|
|
Give the reset worker a kick before losing help when waiting for hang
recovery, as the CPU scheduler is a little unreliable.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-15-chris@chris-wilson.co.uk
|
|
Detect GLK pre-production steppings. Not 100% of A2 being pre-prod
since the spec is a bit of a mess but feels more or less correct.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-4-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
As we require a context switch to ensure that the current context is
switched out and saved to memory, perform an explicit switch to the
kernel context and wait for it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1336
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228082330.2411941-18-chris@chris-wilson.co.uk
|
|
The engine->kernel_context is a special case for request emission. Since
it is used as the barrier within the engine's wakeref, we must acquire the
wakeref before submitting a request to the kernel_context.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-3-chris@chris-wilson.co.uk
|
|
Inside the general i915_oa_init_reg_state() we avoid using the
perf->mutex. However, we rely on perf->exclusive_stream being valid to
access at that point, and for that we have to control the race with
disabling perf. This relies on the disabling being a heavy barrier that
inspects all active contexts, after marking the perf->exclusive_stream
as not available. This should ensure that there are no more concurrent
accesses to the perf->exclusive_stream as we destroy it.
Mark up the races around the perf->exclusive_stream so that they stand
out much more. (And hopefully we will be running kcsan to start
validating that the only races we have are carefully controlled.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-2-chris@chris-wilson.co.uk
|
|
As a disabled pipe in pipe_mask is not having a valid intel crtc,
driver wrongly populates the possible_crtcs mask while initializing
the plane for a CRTC. Fixing up the plane possible_crtcs mask.
changes since RFC:
- Simplify the possible_crtcs initialization. [Ville]
v2:
- Removed the unnecessary stack garbage possible_crtcs to
drm_universal_plane_init. [Ville]
v3:
- Combine the intel_crtc assignment and declaration. [Ville]
v4:
- Fix possible_crtcs abused bits from
intel_{primary,curosr,sprite}_plane_create(). [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163517.31234-1-anshuman.gupta@intel.com
|
|
We need to be extremely careful inside i915_request_await_start() as it
needs to walk the list of requests in the foreign timeline with very
little protection. As we hold our own timeline mutex, we can not nest
inside the signaler's timeline mutex, so all that remains is our RCU
protection. However, to be safe we need to tell the compiler that we may
be traversing the list only under RCU protection, and furthermore we
need to start declaring requests as elements of the timeline from their
construction.
Fixes: 9ddc8ec027a3 ("drm/i915: Eliminate the trylock for awaiting an earlier request")
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-11-chris@chris-wilson.co.uk
|
|
Check that we can recover if the LRC is totally corrupted. Based on a
very simple theory that anything that can be adjusted via the context
(i.e. on behalf of the user), should be under the purview of the
per-engine-reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-13-chris@chris-wilson.co.uk
|
|
Record the LRC registers before/after a preemption event to ensure that
the first context sees nothing from the second client; at least in the
normal per-context register state.
References: https://gitlab.freedesktop.org/drm/intel/issues/1233
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-12-chris@chris-wilson.co.uk
|
|
There is no need to have the 'const struct dispc_csc_coef *coef'
variable static since new value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227065057.92766-1-yuehaibing@huawei.com
|
|
There are two spelling mistakes in warning and debug messages.
Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224174226.387874-1-colin.king@canonical.com
|
