summaryrefslogtreecommitdiff
path: root/drivers/i2c
AgeCommit message (Expand)Author
2015-12-17i2c: make i2c_parse_fw_timings() always visibleWolfram Sang
2015-12-17i2c: emev: select I2C slave supportWolfram Sang
2015-12-16i2c: xlr: add interrupt support for Sigma Designs chipsMåns Rullgård
2015-12-16i2c: xlr: fix extra read/write at end of rx transferMåns Rullgård
2015-12-15i2c: xlr: add support for Sigma Designs controller variantMåns Rullgård
2015-12-14i2c: uniphier_f: error out if bus speed is zeroMasahiro Yamada
2015-12-14i2c: uniphier_f: error out if clock rate is zeroMasahiro Yamada
2015-12-14i2c: uniphier: error out if bus speed is zeroMasahiro Yamada
2015-12-14i2c: uniphier: error out if clock rate is zeroMasahiro Yamada
2015-12-14i2c: rcar: honor additional i2c timings from DTWolfram Sang
2015-12-14i2c: rcar: switch to i2c generic dt parsingWolfram Sang
2015-12-14i2c: rcar: refactor probe function a littleWolfram Sang
2015-12-14i2c: add generic routine to parse DT for timing informationWolfram Sang
2015-12-12i2c: designware: Keep pm_runtime_enable/_disable calls in syncJarkko Nikula
2015-12-12i2c: designware: fix IO timeout issue for AMD controllerXiangliang Yu
2015-12-09i2c: imx: init bus recovery info before adding i2c adapterGao Pan
2015-12-09x86/platform/iosf_mbi: Remove duplicate definitionsAndy Shevchenko
2015-12-07i2c: designware: Convert to use unified device property APIMika Westerberg
2015-12-05i2c: emev2: add slave supportNiklas Söderlund
2015-12-03i2c: eg20t: allow build on MIPS platformsPaul Burton
2015-12-03i2c: eg20t: set i2c_adapter->dev.of_nodePaul Burton
2015-12-03i2c: at91: add support for the HOLD fieldLudovic Desroches
2015-12-03i2c: piix4: remove unneeded assignmentsWolfram Sang
2015-12-01i2c: do not use 0x in front of %paDmitry V. Krivenok
2015-12-01i2c: mediatek: add i2c first write then read optimizationLiguo Zhang
2015-11-30i2c: cadence: Remove the suspended flagShubhrajyoti Datta
2015-11-30i2c: cadence: Move to sensible power managementShubhrajyoti Datta
2015-11-30i2c: bcm2835: add I2C_AQ_NO_CLK_STRETCHNicola Corna
2015-11-30i2c: algo-bit: add I2C_AQ_NO_CLK_STRETCHNicola Corna
2015-11-30i2c: xiic: Replace spinlock with mutexLars-Peter Clausen
2015-11-30i2c: taos-evm: replace simple_strtoul by kstrtou8LABBE Corentin
2015-11-30i2c: davinci: Increase module clock frequencyAlexander Sverdlin
2015-11-30i2c: mv64xxx: The n clockdiv factor is 0 based on sunxi SoCsHans de Goede
2015-11-30i2c: piix4: Add adapter port name support for SB800 chipsetChristian Fetzer
2015-11-30i2c: piix4: Add support for multiplexed main adapter in SB800Christian Fetzer
2015-11-30i2c: piix4: Convert piix4_main_adapter to arrayChristian Fetzer
2015-11-30i2c: rk3x: populate correct variable for sda_falling_timeWolfram Sang
2015-11-30i2c: rcar: handle difference in setting up non-first messageWolfram Sang
2015-11-30i2c: rcar: clean up after refactoringWolfram Sang
2015-11-30i2c: rcar: revoke START request earlyWolfram Sang
2015-11-30i2c: rcar: check master irqs before slave irqsWolfram Sang
2015-11-30i2c: rcar: don't issue stop when HW does it automaticallyWolfram Sang
2015-11-30i2c: rcar: init new messages in irqWolfram Sang
2015-11-30i2c: rcar: refactor setup of a msgWolfram Sang
2015-11-30i2c: rcar: remove spinlockWolfram Sang
2015-11-30i2c: rcar: remove unused IOERROR stateWolfram Sang
2015-11-30i2c: rcar: rework hw initWolfram Sang
2015-11-30i2c: rcar: make sure clocks are on when doing clock calculationWolfram Sang
2015-11-20i2c: i801: add Intel Lewisburg device IDsAlexandra Yates
2015-11-20i2c: fix wakeup irq parsingGrygorii Strashko
generated by cgit (git 2.34.1) at 2025-10-01 07:51:04 +0000