| Age | Commit message (Collapse) | Author |
|---|
|
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632fd ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa28606 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add newlines to the macro definitions and use a more common style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
modifications"
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e9649b ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).
When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).
Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.
Fixes: d1caa9905538 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv
drivers
- Minor fixes and cleanups in various drivers
* tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (22 commits)
hwmon: (aspeed-pwm-tacho) Poll with short sleeps.
hwmon: (aspeed-pwm-tacho) reduce fan_tach period
hwmon: (ibmpowernv) Add current(A) sensor
hwmon: (ibmpowernv) introduce a legacy_compatibles array
hwmon: (pwm-fan) Switch to new atomic PWM API
hwmon: (scpi) Fix the scale of SCP sensor readings
hwmon: (aspeed-pwm-tacho) Enable both edge measurement.
hwmon: (ibmpowernv) Add highest/lowest attributes to sensors
hwmon: (pmbus) move header file out of I2C realm
hwmon: (max6639) move header file out of I2C realm
hwmon: (ltc4245) move header file out of I2C realm
hwmon: (ds620) move header file out of I2C realm
hwmon: (ads1015) move header file out of I2C realm
hwmon: (adt7475) temperature smoothing
hwmon: (adt7475) add high frequency support
hwmon: (adt7475) fan stall prevention
hwmon: (adt7475) replace find_nearest() with find_closest()
hwmon: (pmbus) Add client driver for IR35221
hwmon: (nct6775) Add support for NCT6795D
hwmon: (nct6775) Improve fan detection
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
|
|
This patch fixes the following checkpatch warnings:
Prefer 'unsigned int' to bare use of 'unsigned
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add device tree support for LPS22HB, LPS25H, LPS331AP, LPS001WP
pressure sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add device tree support for L3G4200D, LSM330D, LSM330DL, LSM330DLC,
L3GD20, L3GD20H, L3G4IS, LSM330, LSM9DS0 gyroscope sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add device tree support for LIS3DH, LSM330D, LSM330DL, LSM330DLC,
LIS331DLH, LSM330, LSM303AGR, LIS2DH12, LIS3L02DQ, LNG2DM accel sensors.
Fix LIS302DL support defining of_device_id data field in st_accel_of_match
table
Fixes: 762227721fe6 (iio: accel: st_accel: handle deprecated bindings)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Removes trailing whitespace to fix checkpatch errors
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Open drain should work fine with rising or high level IRQs,
this code was due to some misunderstanding on my part.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This commit adds mt7622 compatible node.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add open drain support in order to share requested IRQ line between
st_lsm6dsx device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add of_match_table for Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add of_match_table for Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In order to add proper device tree support give a more general name
to of_device_id table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add756 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
While the INA226 has a conversion ready flag (CVRF) in the R/W Mask/Enable
register with read-to-clear semantics, the corresponding bit of the INA219
(CNVR) is part of the bus voltage register. The flag is cleared by reading
the power register.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add of_match_table for Measurement Specialties TSYS01 temperature sensor
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Added support for the external hardware trigger on pin ADTRG,
integrated the three possible edges into the driver
and created buffer management for data retrieval
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add of_match_table and point it to a list of compatible device tree
device id's.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Include datasheet links, add i2c_device_id entries, and update
kconfig help for compatible HDC10xx devices: HDC1000, HDC1008,
HDC1010, HDC1050, and HDC1080.
Signed-off-by: Michael Stecklein <m-stecklein@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add proper support for L3GD20H gyroscope sensor. In particular:
- use L3GD20H as device name instead of L3GD20
- fix available full scales
- fix available sample frequencies
Note that the original patch listed first below introduced broken support for
this part. The second patch drops the support as it didn't work.
This new patch brings in working support.
Fixes: 9444a300c2be (IIO: Add support for L3GD20H gyroscope)
Fixes: a0657716416f ("iio:gyro: bug on L3GD20H gyroscope support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add support for the BOSC0200 ACPI device id used on some x86 tablets.
note driver_data is not set to a specific model, driver_data is not
used anyways (instead detection is done on the chip_id reg) and the
2 tablets with a BOSC0200 ACPI device id I've have 2 different chips,
one has a BMA250E, the other a BMA222E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.13 cycle.
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
|
|
Set multiread variable to false for LPS22HB pressure sensor since
it is already enabled in CTRL_REG2. Previous configuration does not
cause any issue in I2C communication since SUB Msb has no meaning
whereas it breaks register address in SPI communication
Fixes: e039e2f5b4da (iio:st_pressure:initial lps22hb sensor support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We want the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SPI bus is never generating error during transfer, so to check if
a chip is correctly connected on a SPI bus we enforce whoami check
to be correct. In this way we can assure SPI probe is failing if
there is no chip connected.
Note that this is really papering over boards that claim the device
is there when it isn't. Not a bad thing to cope with, but not
necessarily stable material.
Fixes: cec0154556f8 ("iio: inv_mpu6050: Check WHO_AM_I register on probe")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Building a kernel with my configuration failed with:
> drivers/built-in.o: In function `hid_sensor_setup_batch_mode': staging/drivers/iio/common/hid-sensors/hid-sensor-trigger.c:104: undefined reference to `iio_buffer_set_attrs'
which is fixed by this patch.
Signed-off-by: Alexander Wuerstlein <arw@arw.name>
Fixes: 138bc7969c24 ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add buffer_impl.h as buffer.h was split into interface for using and
for internals. Without this industrialio-buffer-dmaengine.c fails
to compile.
Fixes:
commit 33dd94cb972175249258329c4aaffddcc82c2005 ("iio:buffer.h - split
into buffer.h and buffer_impl.h")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
