summaryrefslogtreecommitdiff
path: root/drivers/media/i2c
AgeCommit message (Collapse)Author
2022-07-08media: ov5640: Register device propertiesJacopo Mondi
Parse the device properties and register the rotation and orientation V4L2 controls using v4l2_ctrl_new_fwnode_properties(). Remove the open-coded parsing of the rotation property and assume the DTS is correct is providing either <0> or <180> as possible rotations. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Implement get_selectionJacopo Mondi
Implement the get_selection pad operation for the OV5640 sensor driver. The supported targets report the sensor's native size, the active pixel array size and the analog crop rectangle from which the image is produced. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Implement init_cfgJacopo Mondi
Implement the init_cfg pad operation to initialize the subdev state format to the default one. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Change CSI-2 timings to comply with FPSJacopo Mondi
Now that the frame duration can be controlled by tuning the VBLANK duration in CSI-2 mode, fix all modes definitions to comply with the reported FPS. All modes run at 30 FPS except for full-resolution mode 2592x1944 which runs at 15FPS. Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove frame rate check from find_mode()Jacopo Mondi
The current implementation of ov5640_find_mode() fails if the frame rate programmed with s_frame_interval doesn't match the maximum frame rate for the current mode. This causes issues when moving from one mode with higher FPS to another one which only supports a lower FPS range with tools like media-ctl. It also forces users that do not use s_frame_interval(), but rather configure blankings explicitly, to adjust the programmed FPS range to avoid failures. For this reason, remove the FPS check from ov5640_find_mode() and only perform it at s_frame_interval() time. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Adjust vblank with s_frame_intervalHugues Fruchet
Adjust the vertical blanking when s_frame_interval is used. s_frame_interval allows to set a fixed frame rate, which gets stored as the sensor's current one. When a new mode is applied, the current frame rate is reset to the mode's default one. In order to correctly report the currently configured vertical blanking for s_frame_interval users, verify that the desired frame rate has not been changed. If that's the case, compute the correct blanking value and reflect it through the corresponding v4l2 control. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add VBLANK controlJacopo Mondi
Add the VBLANK control which allows to select the duration of the frame vertical blankings and allows to control the framerate. The VBLANK control also modifies the exposure time range, which cannot exceed the maximum frame length. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add HBLANK controlJacopo Mondi
Add the HBLANK control as read-only. The hblank value is fixed in the mode definition and is updated everytime a new format is applied. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove ov5640_mode_init_dataJacopo Mondi
The ov5640_mode_init_data is a fictional sensor more which is used to program the initial sensor settings. It is only used to initialize the sensor and can be replaced it with a throw-away mode which just wraps the register table. Also rename the register table to drop the format from the name to make it clear an actual sensor mode has to be applied after the initial programming. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Remove duplicated mode settingsJacopo Mondi
The register tables for all resolutions smaller than 720p are now identical. Remove the duplicated ones and create a single ov5640_setting_low_res[] register table. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Re-sort per-mode register tablesJacopo Mondi
The per-mode register tables are not sorted by size. Fix it. Cosmetic change only. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Provide timings accessorJacopo Mondi
Provide a function to shortcut access to the correct timings definition to avoid repeating the same pattern when accessing the sensor timings. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Split DVP and CSI-2 timingsJacopo Mondi
Separate the timings for the DVP mode from the timings for the CSI-2 mode in the ov5640 modes definition. The CSI-2 timings will deviate from the DVP ones as the clock tree is calculated differently. In CSI-2 mode change the analog crop rectangles as the OV5640 pixel array is composed as: - vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for a total of 2624 columns - horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6 dummies for a total of 1964 lines Adjust the analog crop rectangle in CSI-2 mode to: - Skip the first 16 dummy columns - Skip the first 14 black/dummy lines - Pass the whole valid pixel array size to the ISP for all modes except 1024x768, 720p and 1080p which are obtained by cropping the valid pixel array. Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Fix 720x480 in RGB888 modeJacopo Mondi
Adjust the left crop of 720x480 to enable capture in RGB888 format, which is otherwise broken. The 56 pixels alignment has been copied from the 720x576 mode. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Rework timings programmingJacopo Mondi
The current definition of a sensor mode defines timings as follows: - hact, vact: Visible width and height - htot, vtot: Total sizes including blankings This makes difficult to clearly separate the visible sizes from the blankings and to make the vertical blanking programmable. Rework the sensor modes sizes definition to: - Report the analog crop sizes - Report the visible crop size - Report the total pixels per line as HBLANK is fixed - Report the VBLANK value to make it programmable Also modify the ov5640_set_timings() function to program all the windowing registers are remove them from the per-mode register-value tables. Do not change the timing values from the ones reported in the register tables to maintain bisectability. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Rework CSI-2 clock treeJacopo Mondi
Re-work the ov5640_set_mipi_pclk() function to calculate the PLL configuration using the pixel_rate and link_freq values set at s_fmt time. Rework the DVP clock mode settings to calculate the pixel clock internally and remove the assumption on the 16bpp format. Tested in MIPI CSI-2 mode with 1 and 2 data lanes with: - all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats. - resolutions >= 1280x720 in RAW Bayer format. - resolutions < 1280x720 in RGB888 format. [Rework pclk_period and link_freq computation] Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Update pixel_rate and link_freqJacopo Mondi
After having set a new format re-calculate the pixel_rate and link_freq control values and update them when in MIPI mode. Take into account the limitation of the link frequency having to be strictly smaller than 1GHz when computing the desired link_freq, and adjust the resulting pixel_rate acounting for the clock tree configuration. [Adjust link_freq calculation] Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add LINK_FREQ controlJacopo Mondi
Add the V4L2_CID_LINK_FREQ control to the ov5640 driver. Make the control read-only for the moment. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Associate bpp with formatsJacopo Mondi
Associate the bit depth to each format supported by the sensor. The bpp will be used to calculate the line length. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add ov5640_is_csi2() functionJacopo Mondi
Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated pattern which is about to be repeated more often. Provide an inline function to shortcut that. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5604: Re-arrange modes definitionJacopo Mondi
The array of supported modes is close to unreadable. Re-arrange it giving it some room to breath. Cosmetic change only. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov5640: Add pixel rate to modesJacopo Mondi
Add to each mode supported by the sensor the ideal pixel rate, as defined by Table 2.1 in the chip manual. The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: st-mipid02: expose 1X16 serial pixel formatHugues Fruchet
Expose RGB & YUV 1X16 serial pixel format variants to comply with CSI-2 camera sensor pixel formats. Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: st-mipid02: add support for YVYU and VYUY formatsAlain Volmat
Those two formats were missing in the list of supported MBUS formats. Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: st-mipid02: add support of pixel clock polarityHugues Fruchet
Add support of pixel clock polarity. Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-08media: ov7251: Fix multiple problems in s_stream callbackSakari Ailus
The s_stream callback had several issues: - If pm_runtime_get_sync() fails, the usage_count is not put. - The sensor wasn't suspended if s_stream(subdev, 1) failed. Fix this. Fixes: ("media: i2c: Add pm_runtime support to ov7251") Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-07-05media: isl7998x: select V4L2_FWNODE to fix build errorRandy Dunlap
Fix build error when VIDEO_ISL7998X=y and V4L2_FWNODE=m by selecting V4L2_FWNODE. microblaze-linux-ld: drivers/media/i2c/isl7998x.o: in function `isl7998x_probe': (.text+0x8f4): undefined reference to `v4l2_fwnode_endpoint_parse' Cc: stable@vger.kernel.org # 5.18 and above Fixes: 51ef2be546e2 ("media: i2c: isl7998x: Add driver for Intersil ISL7998x") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Marek Vasut <marex@denx.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Reviewed-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-06-27media: TDA1997x: Remove now redundant non_legacy_dai_naming flagCharles Keepax
The ASoC core has now been changed to default to the non-legacy DAI naming, as such drivers using the new scheme no longer need to specify the non_legacy_dai_naming flag. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220623125250.2355471-36-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-06-20media: i2c: adv7180: fix reserved bit in Video Selection 2Benjamin Marty
This bit is marked as reserved in the ADV Hardware Reference Manual. Resetting this bit seems to cause increased video noise. Setting this bit according to the Hardware Reference Manual reduces the video noise immediately. Signed-off-by: Benjamin Marty <info@benjaminmarty.ch> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-06-20media: adv7604: try all infoframe typesHans Verkuil
When logging the infoframes the adv7604 driver stopped reading infoframes at the first missing infoframe type. Instead it should try all supported infoframe types. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-06-20media: TDA1997x: Fix the error handling in tda1997x_probe()Zheyu Ma
The driver should disable the regulator when failing to probe. Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Acked-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-06-10treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_30.RULE ↵Thomas Gleixner
(part 2) Based on the normalized pattern: this program is free software you can redistribute it and/or modify it under the terms of the gnu general public license as published by the free software foundation version 2 this program is distributed as is without any warranty of any kind whether express or implied without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference. Reviewed-by: Allison Randal <allison@lohutok.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-17media: ov7251: fix mutex lock unbalanceMauro Carvalho Chehab
As reported by smatch/sparse: drivers/media/i2c/ov7251.c:1381 ov7251_s_stream() warn: inconsistent returns '&ov7251->lock'. Locked on : 1381 Unlocked on: 1377 There's a lock unbalance at this routine, as it keeps the lock on certain errors. Fix it. Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add vblank control to ov7251 driverDaniel Scally
Add a vblank control to the ov7251 driver. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add hblank control to ov7251Daniel Scally
Add a hblank control to the ov7251 driver. This necessitates setting a default mode, for which I am simply picking the first available. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: add ov7251_init_ctrls()Daniel Scally
V4L2 controls initialisation takes up a sizeable portion of the driver's .probe() function. To keep things neat, move it to a dedicated function. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Extend .get_selection() for ov7251Daniel Scally
Extend the .get_selection() callback to support other values for sel->target, primarily to satisfy libcamera's requirements. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Remove .s_power() from ov7251Daniel Scally
The .s_power() callback is deprecated, and now that we have pm_runtime functionality in the driver there's no further use for it. Delete the function. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add pm_runtime support to ov7251Daniel Scally
Add pm_runtime support to the ov7251 driver. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add ov7251_detect_chip()Daniel Scally
.probe() is quite busy for this driver; make it cleaner by moving the chip verification to a dedicated function. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add support for new frequencies to ov7251Daniel Scally
The OV7251 sensor is used as the IR camera sensor on the Microsoft Surface line of tablets; this provides a 19.2MHz external clock, and the Windows driver for this sensor configures a 319.2MHz link freq to the CSI-2 receiver. Add the ability to support those rate to the driver by defining a new set of PLL configs. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add ov7251_pll_configure()Daniel Scally
Rather than having the pll settings hidden inside mode blobs, define them in structs and use a dedicated function to set them. This makes it simpler to extend the driver to support other frequencies for both the external clock and desired link frequency. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Remove per-mode frequencies from ov7251Daniel Scally
Each of the defined modes in the ov7251 driver uses the same link frequency and pixel rate; just drop those members of the modes and set the controls to read only during initialisation. Add a new table defining the supported pixel rates to substitue for the values hardcoded in the modes. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Provide ov7251_check_hwcfg()Daniel Scally
Move the endpoint checking from .probe() to a dedicated function, and additionally check that the firmware provided link frequencies are a match for those supported by the driver. Store the index to the matching link frequency so it can be easily identified later. Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: Add acpi support to ov7251Daniel Scally
Add support for enumeration through ACPI to the ov7251 driver Signed-off-by: Daniel Scally <djrscally@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov5645: Remove unneeded of_match_ptr macroMoses Christopher Bollavarapu
of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: ov8856: apply digital gain by setting global gain control registerBingbu Cao
MWB gain register are used to set gain for each mwb channel mannually. However, it will involve some artifacts if gain cannot be applied to each channel synchronously. Enable global gain control to set digital global gain instead of setting AWB gain separately to fix this issue. Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()Yang Yingliang
IS_ERR() and PTR_ERR() use wrong pointer, it should be sensor->dovdd, fix it. Fixes: e43ccb0a045f ("media: i2c: Add support for the OV5648 image sensor") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: ov2640: Depend on V4L2_ASYNCMike Pagano
Add V4L2_ASYNC as a dependency to match other drivers and prevent failures when compile testing. Fixes: ff3cc65cadb5 ("media: v4l: async, fwnode: Improve module organisation") Signed-off-by: Mike Pagano <mpagano@gentoo.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2022-05-17media: i2c: video-i2c: Use GENMASK for masking bitsMoses Christopher Bollavarapu
Replace 0x0380 with GENMASK(9, 7) to obtain 0b0000_0011_1000_0000 Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-19 18:41:34 +0000