| Age | Commit message (Collapse) | Author |
|---|
|
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481cad ("media: ov5640: Adjust the clock based on the expected rate")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently the various modes are placed into a table, but when
ov5640_find_mode is called, it has to double check whether
or not the requested framerate is tolerated by the mode.
The determination is based on checking hact, vact, and frame rate.
Only 640x480 is allowed at 60fps and QSXGA is limited to 15fps, but
as the number of permitted frame rates change, this will begin to
add more and more complexity to the check.
This patch simplifies the check by adding the max framerate
allowed for each mode into the table of modes. It then compares
the requested framerate to the max permitted in the mode's table.
This reduces the number of comparisions to one down from three
at run-time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If there was an error in starting streaming, put the runtime usage count
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Instead of keeping track of the power state ourselves, let runtime PM
handle it.
This also splits handling controls between side effect management and
writing the new configuration to the sensor's registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The omap3isp driver set the new buffer and enabled the CCDC in a situation
a new buffer was available but streaming was about to be stopped on the
CCDC. This lead to frequent system crashes in case there were buffers
queued when streming was being stopped.
Fix this by first checking whether there's an intent to stop streaming and
if there isn't, then set the new buffer and re-enable CCDC.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The isp was marked to have failed to stop if stopping streaming on an
external subdev failed. The return value from the external subdev should
be ignored instead as it is not part of the ISP and thus the ISP does not
need to be reset for that reason.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Seems to be a clone of Logilink VG0022A. Supports DVB-C, DVB-T and
DVB-T2. Only terrestrial reception was tested on Polish and Czech
multiplexes.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
At least on my system with a self-made IR receiver, my kernel log is filled
with:
serial_ir serial_ir.0: ignoring spike: 1 1 1419988034627194ns 1419956080709377ns
These messages happen at random and do not prevent the receiver from
working. Also I cannot change the features of the IC, therefore they are not
useful. Probably they are not useful at all.
However they fill the console, they accumulate and fill the dmesg log, by
doing this, they prevent me from seeing important message.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This adds support for the PROlectrix DV107669 DVT-T dongle which
uses an RTL2832 and FC0012 tuner.
Tests:
- Verified correct operation of DVB-T reception with VLC across
several UK multiplexes
Signed-off-by: David J. Fiddes <D.J@fiddes.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix checkpatch.pl error by adding a blank line
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
dvb_dummy_fe.c had all its EXPORT_SYMBOL macros located at the end of the
file. Now these are located directly below the symbol they are exporting
for increased readability.
Suggested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Once rc_open is called on the input device, lirc events can be delivered.
Ensure lirc is ready to do so else we might get this:
Registered IR keymap rc-hauppauge
rc rc0: Hauppauge WinTV PVR-350 as
/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/i2c-0/0-0018/rc/rc0
input: Hauppauge WinTV PVR-350 as
/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/i2c-0/0-0018/rc/rc0/input9
BUG: kernel NULL pointer dereference, address: 0000000000000038
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 1 PID: 17 Comm: kworker/1:0 Not tainted 5.3.11-300.fc31.x86_64 #1
Hardware name: /DG43NB, BIOS NBG4310H.86A.0096.2009.0903.1845 09/03/2009
Workqueue: events ir_work [ir_kbd_i2c]
RIP: 0010:ir_lirc_scancode_event+0x3d/0xb0
Code: a6 b4 07 00 00 49 81 c6 b8 07 00 00 55 53 e8 ba a7 9d ff 4c 89
e7 49 89 45 00 e8 5e 7a 25 00 49 8b 1e 48 89 c5 4c 39 f3 74 58 <8b> 43
38 8b 53 40 89 c1 2b 4b 3c 39 ca 72 41 21 d0 49 8b 7d 00 49
RSP: 0018:ffffaae2000b3d88 EFLAGS: 00010017
RAX: 0000000000000002 RBX: 0000000000000000 RCX: 0000000000000019
RDX: 0000000000000001 RSI: 006e801b1f26ce6a RDI: ffff9e39797c37b4
RBP: 0000000000000002 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: ffff9e39797c37b4
R13: ffffaae2000b3db8 R14: ffff9e39797c37b8 R15: ffff9e39797c33d8
FS: 0000000000000000(0000) GS:ffff9e397b680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000038 CR3: 0000000035844000 CR4: 00000000000006e0
Call Trace:
ir_do_keydown+0x8e/0x2b0
rc_keydown+0x52/0xc0
ir_work+0xb8/0x130 [ir_kbd_i2c]
process_one_work+0x19d/0x340
worker_thread+0x50/0x3b0
kthread+0xfb/0x130
? process_one_work+0x340/0x340
? kthread_park+0x80/0x80
ret_from_fork+0x35/0x40
Modules linked in: rc_hauppauge tuner msp3400 saa7127 saa7115 ivtv(+)
tveeprom cx2341x v4l2_common videodev mc i2c_algo_bit ir_kbd_i2c
ip_tables firewire_ohci e1000e serio_raw firewire_core ata_generic
crc_itu_t pata_acpi pata_jmicron fuse
CR2: 0000000000000038
---[ end trace c67c2697a99fa74b ]---
RIP: 0010:ir_lirc_scancode_event+0x3d/0xb0
Code: a6 b4 07 00 00 49 81 c6 b8 07 00 00 55 53 e8 ba a7 9d ff 4c 89
e7 49 89 45 00 e8 5e 7a 25 00 49 8b 1e 48 89 c5 4c 39 f3 74 58 <8b> 43
38 8b 53 40 89 c1 2b 4b 3c 39 ca 72 41 21 d0 49 8b 7d 00 49
RSP: 0018:ffffaae2000b3d88 EFLAGS: 00010017
RAX: 0000000000000002 RBX: 0000000000000000 RCX: 0000000000000019
RDX: 0000000000000001 RSI: 006e801b1f26ce6a RDI: ffff9e39797c37b4
RBP: 0000000000000002 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000001 R12: ffff9e39797c37b4
R13: ffffaae2000b3db8 R14: ffff9e39797c37b8 R15: ffff9e39797c33d8
FS: 0000000000000000(0000) GS:ffff9e397b680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000038 CR3: 0000000035844000 CR4: 00000000000006e0
rc rc0: lirc_dev: driver ir_kbd_i2c registered at minor = 0, scancode
receiver, no transmitter
tuner-simple 0-0061: creating new instance
tuner-simple 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and
compatibles))
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Registered device radio0 for encoder radio
ivtv0: Registered device video16 for decoder MPG (1024 kB)
ivtv0: Registered device vbi8 for decoder VBI (64 kB)
ivtv0: Registered device vbi16 for decoder VOUT
ivtv0: Registered device video48 for decoder YUV (1024 kB)
Cc: stable@vger.kernel.org
Tested-by: Nick French <nickfrench@gmail.com>
Reported-by: Nick French <nickfrench@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This solves the following compiler warnings:
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_gpio_tuner’:
drivers/media/usb/dvb-usb/cxusb.c:128:35: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
128 | deb_info("gpio_write failed.\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_bluebird_gpio_rw’:
drivers/media/usb/dvb-usb/cxusb.c:145:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
145 | deb_info("bluebird_gpio_write failed.\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_i2c_xfer’:
drivers/media/usb/dvb-usb/cxusb.c:251:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
251 | deb_i2c("i2c read may have failed\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c:274:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
274 | deb_i2c("i2c write may have failed\n");
| ^
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
It is not a fatal error if reading the mac address or the remote control
decoder state fails.
Reported-by: syzbot+ec869945d3dde5f33b43@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If usb_bulk_msg() fails, actual_length can be uninitialized.
Reported-by: syzbot+9d42b7773d2fecd983ab@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This results in an uninitialized variable read.
Reported-by: syzbot+6bf9606ee955b646c0e1@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for the four new variants of ioctl commands for 64-bit time_t
in v4l2_buffer.
The existing v4l2_buffer32 structure for the traditional format gets
changed to match the new v4l2_buffer format, and the old layout is
now called v4l2_buffer32_time32. Neither of these matches the native
64-bit architecture format of v4l2_buffer, so both require special
handling in compat code.
Duplicating the existing handlers for the new types is a safe conversion
for now, but unfortunately this may turn into a maintenance burden
later. A larger-scale rework of the compat code might be a better
alternative, but is out of scope of the y2038 work.
Note: x32 support for v4l2_buffer32 has always been broken and remains
so after this change, fixing it would have required even more duplication,
and apparently nobody has cared so far.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: remove spurious newline]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The native code supports the variant of struct v4l2_event for 64-bit
time_t, so add the compat version as well.
Here, a new incompatibility arises: while almost all 32-bit architectures
now use the same layout as 64-bit architectures and the commands can
simply be passed through, on x86 the internal alignment of v4l2_event
is different because of the 64-bit member in v4l2_event_ctrl.
To handle all architectures, this now requires defining four different
versions of the structure to cover all possible combinations. The compat
handling for VIDIOC_DQEVENT32 and VIDIOC_DQEVENT32_TIME32 is now inside
of an #ifdef so it does not get used on architectures other than x86.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The v4l2_buffer structure contains a 'struct timeval' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
As in v4l2_event, handle this with a special case in video_put_user()
and video_get_user() to replace the memcpy there.
Since the structure also contains a pointer, there are now two
native versions (on 32-bit systems) as well as two compat versions
(on 64-bit systems), which unfortunately complicates the compat
handler quite a bit.
Duplicating the existing handlers for the new types is a safe
conversion for now, but unfortunately this may turn into a
maintenance burden later. A larger-scale rework of the
compat code might be a better alternative, but is out of scope
of the y2038 work.
Sparc64 needs a special case because of their special suseconds_t
definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The v4l2_event structure contains a 'struct timespec' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
While passing a 32-bit time_t here would be sufficient for CLOCK_MONOTONIC
timestamps, simply redefining the structure to use the kernel's
__kernel_old_timespec would not work for any library that uses a copy
of the linux/videodev2.h header file rather than including the copy from
the latest kernel headers.
This means the kernel has to be changed to handle both versions of the
structure layout on a 32-bit architecture. The easiest way to do this
is during the copy from/to user space.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The copy-in/out portions of video_usercopy() are about to
get more complex, so turn then into separate functions as
a cleanup first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The do_video_ioctl() compat handler converts the compat command
codes into the native ones before processing further, but this
causes problems for 32-bit user applications that pass a command
code that matches a 64-bit native number, which will then be
handled the same way.
Specifically, this breaks VIDIOC_DQEVENT_TIME from user space
applications with 64-bit time_t, as the structure layout is
the same as the native 64-bit layout on many architectures
(x86 being the notable exception).
Change the handler to use the converted command code only for
passing into the native ioctl handler, not for deciding on the
conversion, in order to make the compat behavior match the
native behavior.
Actual support for the 64-bit time_t version of VIDIOC_DQEVENT_TIME
and other commands still needs to be added in a separate patch.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As a preparation for adding 64-bit time_t support in the uapi,
change the drivers to no longer care about the format of the
timestamp field in struct v4l2_buffer.
The v4l2_timeval_to_ns() function is no longer needed in the
kernel after this, but there is userspace code relying on
it to be part of the uapi header.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: replace spaces by tabs]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
|
|
The v4l2-compliance tests failed with the touch device when multiplanar was
enabled in vivid. Since it is perfectly fine to support the multiplanar API
for touch, add support for this in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There is no reason to prohibit multiplanar support for touch devices,
so just allow it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The v4l2_buffer's 'field' value was never initialized in vivid for the
touch capture device, causing v4l2-compliance errors.
Set it to NONE.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Log (if debug > 0) when a CEC message is received.
This is done for transmits already, so it makes sense to do the
same for receives.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Don't schedule the next ping before the current ping is
sent, schedule it after.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Don't free everything in the disconnect callback, instead use
the adap_free callback, which is called when the last open
filehandle is closed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
It turns out that received CEC messages can arrive faster than
can be processed by the CEC framework, resulting in lost messages.
Instead of storing only one CEC message, store up to 8.
Also fix a bug where the EOM bit wasn't checked for a received
message of length 1, so POLL messages weren't properly reported.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Instead of adap_transmit waiting until the full message
is transmitted (and thus hoarding the adap->lock mutex), have it
kick off a transmit workqueue. This prevents adap->lock from
being locked for a very long time.
Also skip FAILED_ACK reports for broadcast messages: this makes
no sense, and it seems a spurious message coming from the
Pulse-Eight, since some time later I see the SUCCEEDED message.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Instead of translating work_result to a transmit_done status
in pulse8_irq_work_handler(), pass the CEC_TX_STATUS via a
new tx_done_status field.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use debug level 2 to show the low-level Pulse-Eight commands.
Also show the message to transmit on debug level 1 and add a
debug log to show where the transmit failed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Drop the write_lock, rename config_lock to plain lock since this
now locks access to the adapter. Use 'lock' when transmitting
a message, ensuring that nothing interferes with the transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Reorganize the order of the functions in the source, going from
low-level to high-level.
No functional changes were made.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add and use pulse8_msgname() to show the message codes as a
human readable text instead of a number.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The AD7611 chip supports the same Deep Color Mode settings as the AD7604.
This change extends support for this feature to the AD7611 by adding a
wrapper function for the `read_hdmi_pixelclock` hook and adding the same
frequency adjustment logic.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for the sink pad of scaler subdevice to respond
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION ioctls with the following
targets: V4L2_SEL_TGT_COMPOSE_BOUNDS and V4L2_SEL_TGT_CROP.
* Add new const struct crop_rect_default to initialize subdev scaler
properly.
* Make changes in sink pad format reflect to the crop rectangle. E.g.
changing the frame format to a smaller size one can make the former
crop rectangle selects a non existing frame area. To solve this
situation the crop rectangle is clamped to the frame boundaries.
* Clamp crop rectangle respecting the sink bounds during set_selection
ioctl.
Co-developed-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Signed-off-by: Guilherme Alcarde Gallo <gagallo7@gmail.com>
Signed-off-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISI was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISI width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This adds support for GREY and Y16 formats, based on Y10 mbus codes.
Y16 needs to go through preview path in the ISI, with 2 pixels per word,
and it fits the Y16 format. The ISI data lines need to be MSB aligned with
the sensor data lines.
GREY format in 8 bits per pixel is done by dropping the 2 LSB bits
from the Y10 format, and packed as 4 pixels per word.
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISC was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISC width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
With some sensors, the mbus code must match the one that sensor supports.
In this case we should initialize the mbus_code of the fse/fie before
calling the subdev, and not after.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The ISC can receive input from sensors using Y10 format directly
(10 bits greyscale). In this case, the ISC must dump the data directly,
either as GREY (8bit) or Y10 (10bit).
Y16 is not supported because we cannot align the MSB 10 bits to the MSB
inside the 16bit container.
For this format, the ISC internal pipeline cannot work (only works with
BAYER), so we must dump the data directly as 8bit/10bit.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In case the format that the sensor sends is 8 bit only (like GREY for
example) we need to be able to bypass ISC pipeline and directly dump
8 bits.
That's why the hardcoded value of 16 bpp is not correct in all cases.
This change allows the output format to decide what is the correct bpp
(bits per pixel) such that the result is in the proper format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When decoding using the CODA internal rotator (for example NV12
capture), currently the value vb2_buf.index + CODA_MAX_FRAMEBUFFERS (19)
is written into the DEC_PIC_ROT_INDEX register. At least with firmware
version 3.1.1 this causes CODA hangups as soon as the register value
reaches 32. Instead, always write CODA_MAX_FRAMEBUFFERS.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
