| Age | Commit message (Collapse) | Author |
|---|
|
Soft-reset isn't supported in GAUDI. Remove the code that performs it and
print error in case the user wants to do it via sysfs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
Divide iATU initialization into inbound/outbound methods.
We must separate it in order to enable different match mode
per PCIe region.
In addition, added support for PCI address match mode.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
ECC (Error Correcting Code) interrupts are going to be handled
by the FW. Hence, we define an interface in which the driver can
obtain the relevant ECC information.
This information is needed for monitoring and can also lead
to a hard reset if ECC error is not correctable.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
The profiler needs to know the PLL values for correctly showing the
profiling data. Because our firmware can use different PLL configurations,
we need to read the PLL values from the ASIC to pass them to the profiler.
Signed-off-by: Adam Aharon <aaharon@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Use proper bitfield masks instead of shifting values when configuring
packets sent to device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Currently sync stream is limited only for external queues. We want to
remove this constraint by adding a new queue property dedicated for sync
stream. In addition we move the initialization and reset methods to the
common code since we can re-use them with slight changes.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Training schemes requires much more concurrent command submissions than
inference does. In addition, training command submissions can be completed
in a non serialized manner. Hence, we add support in which each ASIC will
be able to configure the amount of concurrent pending command submissions,
rather than use a predefined amount. This change will enhance performance
by allowing the user to add more concurrent work without waiting for the
previous work to be completed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
We no longer need to initialize the rate limiters in GAUDI A1.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
We see that sometimes the CPU in GOYA and GAUDI is occupied by the
power/thermal loop and can't answer requests from the driver fast enough.
Therefore, to avoid false notifications on timeouts, increase the timeout
to 4 seconds on each message sent to the device CPU.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
For debugging purposes, we need to allow the root user better control of
the clock gating feature of the DMA and compute engines. Therefore, change
the clock gating debugfs interface to be bitmask instead of true/false.
Each bit represents a different engine, according to gaudi_engine_id enum.
See debugfs documentation for more details.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
|
|
WREG_BULK is a special packet that has a variable length. Therefore, we
can't parse it when validating CBs that go to the PCI DMA queue. In case
the user needs to use it, it can put multiple WREG32 packets instead.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
|
|
W=1 kernel builds report a lack of description of gaudi_set_asic_funcs()'s
'hdev' argument. In reality it is documented, but the formatting
was not as expected '@.*:'. Instead, there was a misplaced asterisk
which was confusing the kerneldoc validator.
Squashes the following W=1 warning:
drivers/misc/habanalabs/gaudi/gaudi.c:6746: warning: Function parameter or member 'hdev' not described in 'gaudi_set_asic_funcs'
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Link: https://lore.kernel.org/r/20200701085853.164358-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In GAUDI the current timer value for the hardware to check if it is
in IDLE state is too low. As a result, there are occasions where the H/W
wrongly reports it is not IDLE. The driver checks that before submitting
work on behalf of the driver during initialization, so a false report might
cause the driver to fail during device initialization.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
The current timeout is too low for some of the workloads and we see false
errors as a result.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
The PS flow for MMU cache invalidation caused timeouts in stress tests.
Use PS + PI flow so no timeouts should happen whatsoever.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
In Gaudi, the user can't execute scalar load_and_exe on external queue
because it can be a security hole. The driver doesn't parse the commands
being loaded and it can be msg_prot, which the user isn't allowed to use.
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
MMU cache invalidation timeout indicates that the device is unstable and
therefore unusable.
Hence in such case do hard reset and return an error to the user if was
called from ioctl.
In addition, change the print to error level and rephrase its text.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
GAUDI does not support soft-reset as it leaves the NIC ports in an awkward
state, where their QMANs were reset but the NIC itself is still working.
In addition, there is not much sense in doing soft-reset when training is
done on multiple GAUDIs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
Print the event name that caused the soft reset.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
A new sequence is introduced to invalidate the MMU cache in order to avoid
timeouts.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Instead of writing similar event handling code for each ASIC, move the code
to the common firmware file. This code will be used for GAUDI and all
future ASICs.
In addition, add two new fields to the auto-generated events file: valid
and description. This will save the need to manually write the events
description in the source code and simplify the code.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Add the GAUDI code to initialize the ASIC's profiler. The profile receives
its initialization values from the user, same as in Goya, but the code to
initialize is in the driver because the configuration space of the
device is not directly exposed to the user.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Add the code to initialize the security module of GAUDI. Similar to Goya,
we have two dedicated mechanisms for security: Range Registers and
Protection bits. Those mechanisms protect sensitive memory and
configuration areas inside the device.
In addition, in Gaudi we moved to a 3-level security scheme, where the F/W
runs with the highest security level (Privileged), the driver runs with a
less secured level (Secured) and the user is neither privileged nor
secured. The security module in the driver configures the Secured parts so
the user won't be able to access them. The Privileged parts are configured
by the F/W.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
The hwmgr module is responsible for messages sent to GAUDI F/W that are
not common to all habanalabs ASICs.
In GAUDI, we provide the user a simplified mode of controlling the ASIC
clock frequency. Instead of three different clocks, we present a single
clock property that the user can configure via sysfs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Add the ASIC-dependent code for GAUDI. Supply (almost) all of the function
callbacks that the driver's common code need to initialize, finalize and
submit workloads to the GAUDI ASIC.
It also contains the code to initialize the F/W of the GAUDI ASIC and to
receive events from the F/W.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
