| Age | Commit message (Collapse) | Author |
|---|
|
Enables RPMB support for the on-board eMMC of the HiKey board as well
as for eMMC modules connected to the microSD slot.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The main reason to add this check is to avoid unnecessary
mmc_request like the on-going cmd and the corresponding sbc
if the card is removed. Although we have already checked this in
dw_mci_handle_cd for runtime usage of sd card and dw_mci_init_slot
for noremovable devices, but there is a timing gap before it really
calls dw_mci_get_cd as mmc_detect_change needs some delay here.
Another gain here is that we could save some checkings of card status
after sd card been removed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_get_cd have already dealt with these for
both of internal card-detect and gpio card-detect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current value means an mdelay(1) may execute up to 10000000 times,
which translates to around ~2.8 hours. This is probably not what the
orignal author had in mind. Let's instead use 10s, which is the same value
sh_mmcif is using for other timeouts.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sh_mmcif driver is already using a 10s request timeout. Let's also
inform the mmc core about this value, as there are situations when it
needs to know about it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sh_mmcif explicity checks for certain commands to decide when to
enable HW busy detection. Instead, it should only check the response type
as it tells if busy detection is needed.
In this way, the mmc core also gets full control whether it thinks busy
detection should be done or not. In some specific scenarios, like for
ERASE and STOP commands it may decide to fall back to use a CMD13 to poll
the card status instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enable the capabilities which tells the mmc core to prevent sending SD and
SDIO commands during card initialization. In this way, we can also remove
the validation of non-supported commands in the ->request() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There are host drivers which needs to valdiate for non-supported SD
commands and returnn error code for such requests.
To improve and simplify the behaviour, let's invent MMC_CAP2_NO_SD
which these host drivers can set to tell the mmc core to skip sending SD
commands during card initialization.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_dumpregs is used to dump registers when error happens. Thus it should
use pr_err instead of pr_debug to show more information about the hardware.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
[Fix whitespace and checkpatch warnings]
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In linux/mmc/host.h, mmc_card_is_removable() is already defined.
It should be maintainted more easier than now.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work
with arasan,sdhci-5.1) need to know the card clock in order to function
properly. Let's add the ability to expose this clock. Any PHY that
needs to know the clock rate can add a reference and query the clock
rate.
At the moment we register a CLK_GET_RATE_NOCACHE clock that simply
allows querying the clock. This allows us to be less intrusive with
regards to the main SDHCI driver, which has complex logic for adjusting
the SD clock. Right now we always fully power cycle the PHY when the
clock changes and that gives the PHY a good chance to query our clock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan. Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.
>From [1] the corecfg_baseclkfreq is supposed to be set to:
Base Clock Frequency for SD Clock.
This is the frequency of the xin_clk.
This is a relatively easy thing to do. Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time. If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.
At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation. The code is
written in a generic way that should make this easy to extend to other
SoCs. Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.
[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In commit 802ac39a5566 ("mmc: sdhci-of-arasan: fix set_clock when a phy
is supported") we added code to power the PHY off and on whenever the
clock was changed but we avoided doing the power cycle code when the
clock was low speed. Let's now do it always.
Although there may be other reasons for power cycling the PHY when the
clock changes, one of the main reasons is that we need to give the DLL a
chance to re-lock with the new clock.
One of the things that the DLL is for is tuning the Receive Clock in
HS200 mode and STRB in HS400 mode. Thus it is clear that we should make
sure we power cycle the PHY (and wait for the DLL to lock) when we know
we'll be in one of these two speed modes. That's what the original code
did, though it used the clock rate rather than the speed mode. However,
even in speed modes other than HS200,/HS400 the DLL is used for
something since it can be clearly observed that the PHY doesn't function
properly if you leave the DLL off.
Although it appears less important to power cycle the PHY and wait for
the DLL to lock when not in HS200/HS400 modes (no bugs were reported),
it still seems wise to let the locking always happen nevertheless.
Note: as part of this, we make sure that we never try to turn the PHY on
when the clock is off (when the clock rate is 0). The PHY cannot work
when the clock is off since its DLL can't lock.
This change requires ("phy: rockchip-emmc: Increase lock time
allowance") and will cause problems if picked without that change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add SDHCI driver for Broadcom BRCMSTB SoCs.
This driver works with all ARM based SoCs and the 7425, 7429
and 7435 MIPS based SoCs.
The driver disables all UHS speed modes by default and relies
on the Device Tree node properties to enable these modes for
SoC/Board combinations that support them.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Apparently a cut-and-paste error, 'do_data_tag' is using 'brq' for data
size even though 'brq' has not been set up. Instead use blk_rq_sectors().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Certain Hynix eMMC 4.41 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
As some of the other features like BKOPs/Cache/Sanitize are dependent on
HPI feature, those features would also get disabled if HPI is disabled.
Signed-off-by: Pratibhasagar V <pratibha@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
[gdavis: Forward port and cleanup]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
mmc_select_bus_width() returns bus width (4 or 8) on success or
zero if unsupported. So only change mode if setting the bus width
is successful.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If available, eMMC stack uses HC_ERASE_GRP_SIZE as the preferred erase
size. As some high capacity eMMC (64MB) reports this size to 512kB, the
discard operations end up taking very long time.
Improve the behaviour by instead calculating the preferred erase size
based on the eMMC size. In this way the discard operations becomes faster.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
[Ulf: Updated changelog and improved comment in code]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci-bcm2835 is no more needed since it has been replaced
by sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To slove the issue which was found on gru board for hs400.
[ 4.616946] sdhci: Secure Digital Host Controller Interface driver
[ 4.623135] sdhci: Copyright(c) Pierre Ossman
[ 4.722575] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.730962] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[ 4.737444] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[ 4.774930] mmc0: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[ 4.980295] mmc0: switch to high-speed from hs200 failed, err:-84
[ 4.986487] mmc0: error -84 whilst initialising MMC card
We should change HS400 mode selection timing to meet JEDEC
specification. The JEDEC 5.1 said that change the frequency to <= 52MHZ
after HS_TIMING switch. Refer to section 6.6.2.3 "HS400" timing mode
selection:
Set the "Timing Interface" parameter in the HS_TIMING[185] field of the
Extended CSD register to 0x1 to switch to High Speed mode and then set
the clock frequency to a value not greater than 52MHZ.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
with CONFIG_HZ=100, the precision of jiffies is 10ms, and the
generic_cmd6_time of some card is also 10ms. then, may be current
time is only 5ms, but already timed out caused by jiffies precision.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Per JEDEC spec, it is not recommended to use CMD13 to get card status
after speed mode switch. below are two reason about this:
1. CMD13 cannot be guaranteed due to the asynchronous operation.
Therefore it is not recommended to use CMD13 to check busy completion
of the timing change indication.
2. After switch to HS200, CMD13 will get response of 0x800, and even the
busy signal gets de-asserted, the response of CMD13 is aslo 0x800.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some MMC hosts do not support MMC_CAP_WAIT_WHILE_BUSY, but implements the
->card_busy() callback. In such cases, extend __mmc_switch() to use this
method to check card status after switch command.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
host->card_busy() was introduced for SD voltage switching which checks all
4 data lines.
Increasingly, host->card_busy is being used to poll the the busy signal
which is only data line 0 (DAT[0]).
The current logic in sdhci_card_busy() does not work in that case because
it returns false if any of the data lines is high. It also ignores
possibilities:
- data lines 1-3 are not connected and could show at any level
- data lines 1-2 can be used by SDIO for other purposes
According to the SD specification, it is OK to check any of the data lines
for voltage switching, so change to use DAT[0] only.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Sparse complains about the implicit cast. Making it explicit is indeed
better coding style.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently sdhci-arasan 5.1 can support enhanced strobe function,
and we now limit it just for "arasan,sdhci-5.1". Add
mmc-hs400-enhanced-strobe in DT to enable the function if we're
sure our controller can support it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We introduce HS400 with enhanced strobe function, so we need
to add it for debug show.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Controllers use data strobe line to latch data from devices
under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC
introduces enhanced strobe mode for latching cmd response from
emmc devices to host controllers. This new feature is optional,
so it depends both on device's cap and host's cap to decide
whether to use it or not.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch introduce mmc-hs400-enhanced-strobe for platforms
which want to enable enhanced strobe function from DT if the
mmc host controller claims to support enhanced strobe.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Activating wakeup event is not enough to get a wakeup signal. The
corresponding events have to be enabled in the Interrupt Status Enable
Register too. It follows the specification and is needed at least by
sdhci-of-at91.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In sectors alignment check, brq->data.blocks means sectors of the
previous mqrq since data.blocks for mqrq_cur hasn't been updated yet.
data.blocks will be updated later in mmc_blk_packed_hdr_wrq_prep or
mmc_blk_rw_rq_prep.
static int mmc_blk_issue_rw_rq(struct mmc_queue *mq, ......
......
struct mmc_blk_request *brq = &mq->mqrq_cur->brq;
Signed-off-by: Yuan Juntao <juntao.yuan@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since commit 7ce45e950624 ("mmc: sdhci: SD tuning is broken for some
controllers") sdhci_execute_tuning() no longer includes a timeout in its
loop counter(s) so remove portion of the comment regarding this.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Replace hardcoded values with meaningful names and document what we
know.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As reported by Dan in his report in [1], there is a potential NULL
pointer derefence if these conditions are met :
- there is no platform_data provided, ie. host->pdata = NULL
Fix this by only using the platform data ro_invert when a gpio for
read-only is provided by the platform data.
This doesn't appear yet as every pxa board provides a platform_data, and
calls pxa_set_mci_info() with a non NULL pointer.
[1] [bug report] mmc: pxamci: fix card detect with slot-gpio API.
The commit fd546ee6a7dc ("mmc: pxamci: fix card detect with slot-gpio
API") from Sep 26, 2015, leads to the following static checker warning:
drivers/mmc/host/pxamci.c:809 pxamci_probe()
warn: variable dereferenced before check 'host->pdata' (see line 798)
Fixes: fd546ee6a7dc ("mmc: pxamci: fix card detect with slot-gpio API")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Convert header data to LE.
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Set 'idata->buf' to NULL so that it never gets returned without
initialization. This fixes a bug where mmc_blk_ioctl_cmd() would
free both 'idata' and 'idata->buf' but 'idata->buf' was returned
uninitialized.
Fixes: 1ff8950c0433 ("mmc: block: change to use kmalloc when copy data from userspace")
Signed-off-by: Ville Viinikka <ville@tuxera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for the removal of 'driverfs_dev' from 'struct gendisk',
carry this data in mmc_blk_data. It is used for registration of parent
disks and partitions.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Another straightforward replacement of magic numbers.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: jacob.jun.pan@intel.com
Cc: linux-mmc@vger.kernel.org
Link: http://lkml.kernel.org/r/20160603001951.9EEA53D8@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The req operation REQ_OP is separated from the rq_flag_bits
definition. This converts the block layer drivers to
use req_op to get the op from the request struct.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Now the the HS-DDR mode clock timings have been corrected, we can
re-enable these modes on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC clock timings were incorrectly calculated, when the conversion
from delay value to delay phase was done.
The 50M DDR and 50M DDR 8bit timings are off, and make eMMC DDR
unusable. Unfortunately it seems different controllers on the same SoC
have different timings. The new settings are taken from mmc2, which is
commonly used with eMMC.
The settings for the slower timing modes seem to work despite being
wrong, so leave them be.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When IS_ERR_VALUE was removed from the mmc core code, it was replaced
with a simple not-zero check. This does not work, as the value checked
is the return value for mmc_select_bus_width, which returns the set
bit width on success. This made eMMC modes higher than HS-DDR unusable.
Fix this by checking for a positive return value instead.
Fixes: 287980e49ffc ("remove lots of IS_ERR_VALUE abuses")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.7 rc1. They are based on a
commit earlier in the merge window and have been tested in linux-next
for a while.
MMC core:
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly"
* tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: sdhci-pci: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
mmc: dw_mmc: rockchip: Set the drive phase properly
mmc: dw_mmc: fix the wrong max_blk_size
mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
mmc: sdhci-acpi: Ensure connected devices are powered when probing
ACPI / PM: Export acpi_device_fix_up_power()
mmc: block: Pause re-tuning while switched to the RPMB partition
mmc: block: Always switch back to main area after RPMB access
mmc: core: Add a facility to "pause" re-tuning
|
|
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The CMD19/CMD14 bus width test has been found to be unreliable in
some cases. It is not essential, so simply remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
