| Age | Commit message (Collapse) | Author |
|---|
|
We don't need to manually toggle the CE line since the controller handles
it for us. Moreover, keeping the CE line low when interacting with a DDR
NAND can be problematic (data loss in some corner cases).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Try to pack address and command cycles into a single NAND controller
command to avoid polling the status register for each single change
on the NAND bus.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Being able to read subpages can greatly improve read performances if the
MTD user is only interested in a small section of a NAND page.
This is particularly true with large pages (>= 8k).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Allwinner's ECC engine is capable of protecting a few bytes of the OOB
area. Implement specific OOB functions to benefit from this capability.
Also, when in raw mode, the randomizer is disabled, which means you'll
only be able to retrieve randomized data, which is not really useful
for most applications.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Export the default read/write oob functions (for the standard and syndrome
scheme), so that drivers can use them for their raw implementation and
implement their own functions for the normal oob operation.
This is required if your ECC engine is capable of fixing some of the OOB
data. In this case you have to overload the ->read_oob() and ->write_oob(),
but if you don't specify the ->read/write_oob_raw() functions they are
assigned to the ->read/write_oob() implementation, which is not what you
want.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Adapt the NAND controller clk rate to the tWB, tADL, tWHR and tRHW
timings instead of returning an error when the maximum clk divisor is
not big enough to provide an appropriate timing.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The ONFI spec says that EDO should be enabled if the host drives tRC less
than 30ns, but the code just tests for the tRC_min value extracted from
the timings exposed by the NAND chip not the timings actually configured
in the NAND controller.
Fix that by first rounding down the requested clk_rate with
clk_round_rate() and then checking if tRC is actually smaller than 30ns.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Unlike what is specified in the Allwinner datasheets, the NAND clock rate
is not equal to 2/T but 1/T. Fix the clock rate selection accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
sunxi_nand_chip_set_timings() is extracting a pointer to the nfc from the
nand->controller field, but this field is initialized after
sunxi_nand_chip_set_timings() call.
Reorder the calls to avoid any problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
It also contains some minor related changes:
1) Don't warn if kzalloc fails as it dumps stack on its own
2) Use %pR format for displaying whole resource to avoid invalid format
warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
|
|
Some drivers are including linux/of_mtd.h even if they don't use any of
the of_get_nand_xxx() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
|
|
If there is only one bit difference in the ECC, the function should
return 1.
The result of "diff0 & ~(1<<fls(diff0))" is equal to diff0, so the
function actually returns -1.
Signed-off-by: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The new IFC controller version 2.0 has a different memory map page.
Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB.
This patch segregates the IFC global and runtime registers to appropriate
PAGE sizes.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There's no reason to BUG() when parameters are being
validated. Drivers can get things wrong, and it's much nicer
to just throw a noisy warn and fail gracefully, than calling
BUG() and throwing the whole system down the drain.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
fix the raw_buffer pointer double free issue found by coverify.
CID 18344 (#2 of 2): Double free (USE_AFTER_FREE)
3. double_free: Calling gpmi_alloc_dma_buffer frees pointer
this->raw_buffer which has already been freed
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Document and match the brcm,brcmnand-v6.2 compatible string, the controller has
a register layout identical to the v6.0 version and supports prefetch. Update the
command shift logic to account for v6.2 controller which are the first ones to
use a shift of 0 (6.1 used a shift of 24).
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
bch->dev is already assigned to &pdev->dev in the probe function.
Remove the duplicate assignment done in jz4780_bch_get().
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Acked-by: Harvey Hunt <harvey.hunt@imgtec.com>
|
|
New atmel SoCs are able to fix bitflips in erased pages, but old ones
are still impacted by this problem. Use nand_check_erased_ecc_chunk() to
handle this case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Herve Codina <herve.CODINA@celad.com>
Reviewed-by: Herve Codina <herve.CODINA@celad.com>
Tested-by: Herve Codina <herve.CODINA@celad.com>
|
|
This follows recent work on switching to enum nand_ecc_algo and
deprecating NAND_ECC_SOFT_BCH.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Use recently added of_get_nand_ecc_algo for that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds into nand/next
Pull leds-trigger changes from Jacek Anaszewski.
Create a generic mtd led-trigger to replace the exisitng nand led-trigger
implementation.
* 'mtd-nand-trigger' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
mtd: Hook I/O activity to the MTD LED trigger
mtd: nand: Remove the "nand-disk" LED trigger
leds: trigger: Introduce a MTD (NAND/NOR) trigger
mtd: Uninline mtd_write_oob and move it to mtdcore.c
leds: trigger: Introduce a kernel panic LED trigger
|
|
This patch fix spelling typos found in printk
within various part of the kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull MTD fix from Brian Norris:
"One MTD fix for v4.6-rc4:
In the v4.4 cycle, we relaxed the requirement for assigning
mtd->owner, but we didn't remove this error case. It's hit only
by drivers that are both:
(a) using nand_scan() directly
and
(b) built as modules
We haven't seen explicit complaints about this (most use cases don't
fit one or both of the above), but we should definitely not be
BUG()'ing here"
* tag 'for-linus-20160415' of git://git.infradead.org/linux-mtd:
mtd: nand: Drop mtd.owner requirement in nand_scan
|
|
The GPMC WAIT pin status are now available over gpiolib.
Update the omap_dev_ready() function to use gpio instead of
directly accessing GPMC register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Copy all the platform data parameters to the driver's local data
structure 'omap_nand_info' and use it in the entire driver. This will
make it easer for device tree migration.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Instead of accessing the gpmc_status register directly start
using the gpmc_nand_ops->nand_writebuffer_empty() helper
to check write buffer empty status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Deprecate nand register passing via platform data and use
gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we've added the MTD LED trigger, we need
to call each I/O path to ledtrig_mtd_activity.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This commit removes the "nand-disk" LED trigger from the
NAND code.
A trigger with the same name is already available selecting
LEDS_TRIGGER_MTD. Note that "nand-disk" trigger is being
deprecated in favor of the "mtd" trigger.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
There's no reason for having mtd_write_oob inlined in mtd.h header.
Move it to mtdcore.c where it belongs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Certain SPI controllers may provide accelerated hardware interface to
read from m25p80 type flash devices in order to provide better read
performance. SPI core supports such devices with spi_flash_read() API.
Call spi_flash_read(), if supported, to make use of such interface.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[Brian: add memset()]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to support device tree probing of Versatile NOR flash
chips, there must be a way to add the VPP (write protection)
enable/disable callback. The register in question is in the
system controllers of these machines. Apart from this quirk,
the ARM flash chips are standard CFI flash chips from various
vendors.
Additionally, the Integrator/AP require you to set up the external
bus interface (EBI) to allow writes to the chip select where the
flash memory is connected.
Solve this by looking for the arm,versatile-flash compatible
string in the flash device tree node. In the driver,
add a special hook to check for the various Versatile syscons and
register a callback for .set_vpp() if this compatible is present.
Provide a special Kconfig entry for the addon hook so it will
not be compiled in if the Versatile boards are not supported.
Stubs in the header file make sure the impact will be zero on
other platforms. (Compilers optimze this out.)
With this patch, a large slew of ARM board file code can be
removed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit 06968a54790d ("mtd: pxa2xx-flash: switch from
ioremap_cache to memremap"), since NOR with memory semantics in array mode
and RAM are not necessarily the same thing, and architectures may implement
ioremap_cached() and memremap() with different memory attributes.
For this reason, ioremap_cached() has been brought back from the dead on
the ARM side, so switch this driver back to using it instead of memremap().
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
Using KSEG0ADDR makes code highly MIPS dependent and not portable.
Thanks to the fix a68f376 ("MIPS: io.h: Define `ioremap_cache'") we can
use ioremap_cache which is generic and supported on MIPS as well now.
KSEG0ADDR was translating 0x1c000000 into 0x9c000000. With ioremap_cache
we use MIPS's __ioremap (and then remap_area_pages). This results in
different address (e.g. 0xc0080000) but it still should be cached as
expected and it was successfully tested with BCM47186B0.
Other than that drivers/bcma/driver_chipcommon_sflash.c nicely setups a
struct resource for access window, but we wren't using it. Use it now
and drop duplicated info.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
|
When map_word gets too large, we use a lot of kernel stack, and for
MTD_MAP_BANK_WIDTH_32, this means we use more than the recommended
1024 bytes in a number of functions:
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_write_buffers':
drivers/mtd/chips/cfi_cmdset_0020.c:651:1: warning: the frame size of 1336 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_erase_varsize':
drivers/mtd/chips/cfi_cmdset_0020.c:972:1: warning: the frame size of 1208 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'do_write_buffer':
drivers/mtd/chips/cfi_cmdset_0001.c:1835:1: warning: the frame size of 1240 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This can be avoided if all operations on the map word are done
indirectly and the stack gets reused between the calls. We can
mostly achieve this by selecting MTD_COMPLEX_MAPPINGS whenever
MTD_MAP_BANK_WIDTH_32 is set, but for the case that no other
bank width is enabled, we also need to use a non-constant
map_bankwidth() to convince the compiler to use less stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Brian: this patch mostly achieves its goal by forcing
MTD_COMPLEX_MAPPINGS (and the accompanying indirection) for 256-bit
mappings; the rest of the change is mostly a wash, though it helps
reduce stack size slightly. If we really care about supporting
256-bit mappings though, we should consider rewriting some of this
code to avoid keeping and assigning so many 256-bit objects on the
stack.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
