| Age | Commit message (Collapse) | Author |
|---|
|
While UBI and UBIFS seem to work at first sight with MLC NAND, you will
most likely lose all your data upon a power-cut or due to read/write
disturb.
In order to protect users from bad surprises, refuse to attach to MLC
NAND.
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
|
|
When opening a device with write access, ubiblock_open returns an error
code. Currently, this error code is -EPERM, but this is not the right
value.
The open function for other block devices returns -EROFS when opening
read-only devices with FMODE_WRITE set. When used with dm-verity, the
veritysetup userspace tool is expecting EROFS, and refuses to use the
ubiblock device.
Use -EROFS for ubiblock as well. As a result, veritysetup accepts the
ubiblock device as valid.
Cc: stable@vger.kernel.org
Fixes: 9d54c8a33eec (UBI: R/O block driver on top of UBI volumes)
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
At this point UBI volumes have already been free()'ed and fastmap can no
longer access these data structures.
Reported-by: Martin Townsend <mtownsend1973@gmail.com>
Fixes: 74cdaf24004a ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system")
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mtd/next
Backmerge v4.16-rc2 into mtd/next to resolve a conflict between Linus'
master branch and nand/for-4.17.
|
|
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
|
|
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
|
|
Currently on a imx6sx-sdb board, which has two SPI NOR chips connected
to QSPI2 the following output from /proc/mtd is seen:
dev: size erasesize name
mtd0: 01000000 00010000 "21e4000.qspi"
mtd1: 01000000 00010000 "21e4000.qspi"
Attempts to partition them on the kernel command line result in both
chips with identical (and identically named) partitions, which is
an inconvenient behavior.
Assign a different mtd->name for each mtd device to avoid this problem.
After this change the output from /proc/mtd becomes:
dev: size erasesize name
mtd0: 01000000 00010000 "21e4000.qspi-0"
mtd1: 01000000 00010000 "21e4000.qspi-1"
In order to keep mtdparts compatibility keep the mtd->name
unchanged when a single SPI NOR is present.
Reported-by: David Wolfe <david.wolfe@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
In core.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>] lr : [<00000004>] psr: 60000013
sp : c382dd18 ip : 0000ffff fp : 00000000
r10: c0626388 r9 : 00020000 r8 : c0626340
r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70
r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 0000397f Table: 00004000 DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
|
|
platform_driver_register() takes care of assigning driver->bus
to &platform_bus_type, no need to explicitly assign it in the driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
|
|
The core clock field was badly named ->ecc_clk which might lead to some
confusion. Rename it ->core_clk.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Prepare the migration of the lpc32xx_slc driver to use nand_scan() by
cleaning the error path in the probe function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The kernel.h macro DIV_ROUND_UP performs the computation
(((n) + (d) - 1) / (d)) but is perhaps more readable.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
In mtdcore.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
It is not necessary for all device's maps to be CFI_HOST_ENDIAN.
Maps device can be Big endian or little endian.
Currently it is being taken care using CONFIG_MTD_CFI_LE_BYTE_SWAP or
CONFIG_MTD_CFI_BE_BYTE_SWAP i.e. compile time.
Now update struct map_info's swap field based on device characteristics
defined in device tree.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
In the commit 2c77c57d22adb ("mtd: move code adding master MTD out of
mtd_add_device_partitions()") behavior of mtd_device_parse_register()
has very slightly changed. It's a pretty non-significant order change
to match updated function behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This adds the JEDEC IDs for Eon EN29LV400A variants
EN29LV400AB and EN29LV400AT. This chip is found in the
D-Link DNS-313.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
This allows using this parser with any flash driver that takes care of
setting of_node (using mtd_set_of_node helper) correctly. Up to now
support for "fixed-partitions" DT compatibility string was working only
with flash drivers that were specifying "ofpart" (manually or by letting
mtd use the default set of parsers).
This matches existing bindings documentation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Type "ofpart" means that OF should be used to get partitioning info and
this driver supports "fixed-partitions" binding only. Renaming it should
lead to less confusion especially when parsers for new compatibility
strings start to appear.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
In order to properly support compatibility strings as described in the
bindings/mtd/partition.txt "ofpart" type should be treated as an
indication for looking into OF. MTD should check "compatible" property
and search for a matching parser rather than blindly trying the one
supporting "fixed-partitions".
It also means that existing "fixed-partitions" parser should get renamed
to use a more meaningful name.
This commit achievies that aim by introducing a new mtd_part_of_parse().
It works by looking for a matching parser for every string in the
"compatibility" property (starting with the most specific one).
Please note that driver-specified parsers still take a precedence. It's
assumed that driver providing a parser type has a good reason for that
(e.g. having platform data with device-specific info). Also doing
otherwise could break existing setups. The same applies to using default
parsers (including "cmdlinepart") as some overwrite DT data with cmdline
argument.
Partition parsers can now provide an of_match_table to enable
flash<-->parser matching via device tree as documented in the
mtd/partition.txt.
This support is currently limited to built-in parsers as it uses
request_module() and friends. This should be sufficient for most cases
though as compiling parsers as modules isn't a common choice.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes: 656441478ed5 ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes: bccb06c353af ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes: 82771882d960 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The blackfin architecture is getting removed, so this driver
has become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
When there is only a single erase block, the cross erase test
does not report sensible errors. Warn in case there is only
a single erase block instead of executing the test.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Use %*ph format to print small buffer as hex string.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
|
|
GPMI driver timings derivation looks very empirical and does not use
the known timings that the core wants to use with the NAND chip, by
using local defined constants that have no special meaning from the
outside world.
Simplify the way all of this is computed and use the NAND core's SDR
timings.
Integrity of the reads/writes has been checked with nandbiterrs, speed
improvements with flash_speed on a Freescale i.MX6 DualLite/Solo SABRE
Automotive Board. Measures are below, variations of less than 150kiB/s
between tests are common and then not significant. Speeds using mode 5
are the same, while speeds using mode 0 are quite improved (+40/50%
from non-optimal computation).
Forcing timings mode 0:
=======================
Before this patch:
------------------
eraseblock write speed is 2298 KiB/s
eraseblock read speed is 3636 KiB/s
page write speed is 2136 KiB/s
page read speed is 3316 KiB/s
2 page write speed is 2199 KiB/s
2 page read speed is 3468 KiB/s
After this patch:
-----------------
eraseblock write speed is 3232 KiB/s
eraseblock read speed is 5663 KiB/s
page write speed is 2915 KiB/s
page read speed is 4904 KiB/s
2 page write speed is 3084 KiB/s
2 page read speed is 5267 KiB/s
Forcing timings mode 5:
=======================
Before this patch:
------------------
eraseblock write speed is 4338 KiB/s
eraseblock read speed is 14883 KiB/s
page write speed is 3786 KiB/s
page read speed is 12800 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
After this patch:
-----------------
eraseblock write speed is 4309 KiB/s
eraseblock read speed is 14712 KiB/s
page write speed is 3764 KiB/s
page read speed is 12673 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
After a nand_reset_data_interface(), both the NAND chip and the NAND
controller use timing mode 0. The previously defined data interface for
this chip has been saved and is supposed to be restored after that.
However, if the saved data interface also refers to timing mode 0, there
is no need to re-apply them again.
Also, as nand_setup_data_interface() uses ->set/get_features(), it could
lead to issues when doing the reset at probe time as the parameter page
is not available yet to know if these functions are supported or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Choosing ONFI timings when ->set/get_features() calls are supported
by the NAND chip is a matter of reading the chip's ONFI parameter page
and telling the chip the chosen mode (between all of the supported ones)
with ->set_feature().
Add a check on whether the chip "acked" the timing mode or not.
This can be a problem for NAND chips that do not follow entirely the
ONFI specification. These chips actually support other modes than
"mode 0", but either:
1/ do not update the timing mode register once a timing mode has been
selected.
or
2/ do not support the TIMING_MODE featured and thus do not require users
to change the timing mode at all.
These issues will be addressed in another patch that will add the
feature to overwrite NAND chips features within the parameter page, from
the NAND chip driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
After a ->set_features(TIMINGS), the chip is supposed to be working at a
new speed. In order for all the transactions to be perperly handled, the
NAND controller should also be configured to this same speed. Calling
->setup_data_interface() is not enough and the chip should be
de-asserted/re-asserted through calls to ->select_chip().
Prepare the next change in nand_setup_data_interface() where timings
will be checked after being applied. Because assertions of the CS pin
will be needed from within this function, move the calls to
->select_chip() inside nand_setup_data_interface() for later
consistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
All the calls to the chip's hooks ->get/set_features() go through
the core's wrappers nand_get/set_features() that already do the
necessary checks about feature support. Remove these
checks from the mxc's functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
