| Age | Commit message (Collapse) | Author |
|---|
|
Integrate the SD library calls into the auxiliary_driver ops in
preparation for creating a single netdev for the multiple PFs belonging
to the same SD group.
SD is still disabled at this stage. It is enabled by a downstream patch
when all needed parts are implemented.
The netdev is created whenever the SD group, with all its participants,
are ready. It is later destroyed whenever any of the participating PFs
drops.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add debugfs entries that describe the Socket-Direct group.
Example:
$ grep -H . /sys/kernel/debug/mlx5/0000\:08\:00.0/multi-pf/*
/sys/kernel/debug/mlx5/0000:08:00.0/multi-pf/group_id:0x00000101
/sys/kernel/debug/mlx5/0000:08:00.0/multi-pf/primary:0000:08:00.0 vhca 0x0
/sys/kernel/debug/mlx5/0000:08:00.0/multi-pf/secondary_0:0000:09:00.0 vhca 0x2
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Print to kernel log when an SD group moves from/to ready state.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Implement the needed SD steering adjustments for the primary and
secondaries.
While the SD multiple PFs are used to avoid cross-numa memory, when it
comes to chip level all traffic goes only through the primary device.
The secondaries are forced to silent mode, to guarantee they are not
involved in any unexpected ingress/egress traffic.
In RX, secondary devices will not have steering objects. Traffic will be
steered from the primary device to the RQs of a secondary device using
advanced cross-vhca RX steering capabilities.
In TX, the primary creates a new TX flow table, which is aliased by the
secondaries.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Use devcom to communicate between the different devices. Add a new
devcom component type for this.
Each device registers itself to the devcom component <SD, group ID>.
Once all devices of a component are registered, the component becomes
ready, and a primary device is elected.
In principle, any of the devices can act as a primary, they are all
capable, and a random election would've worked. However, we aim to
achieve predictability and consistency, hence each group always choses
the same device, with the lowest PCI BUS number, as primary.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add implementation for querying the MPIR register for Socket-Direct
attributes, and instantiating a SD struct accordingly.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add Socket-Direct API with empty/minimal implementation.
We fill-in the implementation gradually in downstream patches.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch updates the mlxbf_gige driver to support the
"get_pause_stats()" callback, which enables display of
pause frame counters via "ethtool -I -a oob_net0".
The pause frame counters are only enabled if the "counters_en"
bit is asserted in the LLU general config register. The driver
will only report stats, and thus overwrite the default stats
state of ETHTOOL_STAT_NOT_SET, if "counters_en" is asserted.
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240305212137.3525-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Found with git grep 'MODULE_AUTHOR(".*([^)]*@'
Fixed with
sed -i '/MODULE_AUTHOR(".*([^)]*@/{s/ (/ </g;s/)"/>"/;s/)and/> and/}' \
$(git grep -l 'MODULE_AUTHOR(".*([^)]*@')
Also:
in drivers/media/usb/siano/smsusb.c normalise ", INC" to ", Inc";
this is what every other MODULE_AUTHOR for this company says,
and it's what the header says
in drivers/sbus/char/openprom.c normalise a double-spaced separator;
this is clearly copied from the copyright header,
where the names are aligned on consecutive lines thusly:
* Linux/SPARC PROM Configuration Driver
* Copyright (C) 1996 Thomas K. Dyas (tdyas@noc.rutgers.edu)
* Copyright (C) 1996 Eddie C. Dost (ecd@skynet.be)
but the authorship branding is single-line
Link: https://lkml.kernel.org/r/mk3geln4azm5binjjlfsgjepow4o73domjv6ajybws3tz22vb3@tarta.nabijaczleweli.xyz
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Introduce ixgbe_update_{r,t}x_ring_stats() that will be used by both
standard and ZC datapath.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The "qv_info" ptr cannot be NULL when it gets the address of
an element of the flexible array "qvlist_info->qv_info".
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There are currently two pairs of identical checks and calls
to iavf_{add|del}_cloud_filter().
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Following the addition of new GTP RSS hash options to ethtool.h, this patch
implements the corresponding RSS settings for GTP packets in the Intel ice
driver. It enables users to configure RSS for GTP-U and GTP-C traffic over IPv4
and IPv6, utilizing the newly defined hash options.
The implementation covers the handling of gtpu(4|6), gtpc(4|6), gtpc(4|6)t,
gtpu(4|6)e, gtpu(4|6)u, and gtpu(4|6)d traffic, providing enhanced load
distribution for GTP traffic across multiple processing units.
Signed-off-by: Takeru Hayasaka <hayatake396@gmail.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Simplify stats accumulation logic to fix the case where we don't take
previous stat value into account, we should always respect it.
Main netdev stats of our PF (Tx/Rx packets/bytes) were reported orders of
magnitude too big during OpenStack reconfiguration events, possibly other
reconfiguration cases too.
The regression was reported to be between 6.1 and 6.2, so I was almost
certain that on of the two "preserve stats over reset" commits were the
culprit. While reading the code, it was found that in some cases we will
increase the stats by arbitrarily large number (thanks to ignoring "-prev"
part of condition, after zeroing it).
Note that this fixes also the case where we were around limits of u64, but
that was not the regression reported.
Full disclosure: I remember suggesting this particular piece of code to
Ben a few years ago, so blame on me.
Fixes: 2fd5e433cd26 ("ice: Accumulate HW and Netdev statistics over reset")
Reported-by: Nebojsa Stevanovic <nebojsa.stevanovic@gcore.com>
Link: https://lore.kernel.org/intel-wired-lan/VI1PR02MB439744DEDAA7B59B9A2833FE912EA@VI1PR02MB4397.eurprd02.prod.outlook.com
Reported-by: Christian Rohmann <christian.rohmann@inovex.de>
Link: https://lore.kernel.org/intel-wired-lan/f38a6ca4-af05-48b1-a3e6-17ef2054e525@inovex.de
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b47b ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The IGC_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read IGC_TSIRC into 'tsicr';
2. handle the interrupts present in 'tsirc' and mark them in 'ack';
3. write 'ack' into IGC_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-04 (ice)
This series contains updates to ice driver only.
Jake changes the driver to use relative VSI index for VF VSIs as the VF
driver has no direct use of the VSI number on ice hardware. He also
reworks some Tx/Rx functions to clarify their uses, cleans up some style
issues, and utilizes kernel helper functions.
Maciej removes a redundant call to disable Tx queues on ifdown and
removes some unnecessary devm usages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The R-Car and RZ/G2L Rx code paths were split in two separate
implementations when support for RZ/G2L was added due to the fact that
R-Car uses the extended descriptor format while RZ/G2L uses normal
descriptors. This has led to a duplication of Rx logic with the only
difference being the different Rx descriptors types used. The
implementation however neglects to take into account that extended
descriptors are normal descriptors with additional metadata at the end
to carry hardware timestamp information.
The hardware timestamp information is only consumed in the R-Car Rx
loop and all the maintenance code around the Rx ring can be shared
between the two implementations if the difference in descriptor length
is carefully considered.
This change merges the two implementations for Rx ring maintenance by
adding a method to access both types of descriptors as normal
descriptors, as this part covers all the fields needed for Rx ring
maintenance the only difference between using normal or extended
descriptor is the size of the memory region to allocate/free and the
step size between each descriptor in the ring.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make it possible to merge the R-Car and RZ/G2L code paths move the
maximum usable size of a single Rx descriptor data slice into the
hardware information instead of using two different defines in the two
different code paths.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the define describing the RZ/G2L maximum frame size and only use
the information in the hardware information struct. This will make it
easier to merge the R-Car and RZ/G2L code paths.
There is no functional change as both the define and the maximum frame
length in the hardware information is set to 8K.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EtherAVB device requires the SKB data to be aligned to 128 bytes.
The alignment is done by allocating an skb 128 bytes larger than the
maximum frame size supported by the device and adjusting the headroom to
fit the requirement.
This code has been refactored a few times and small issues have been
added along the way. The issues are not harmful but prevent merging
parts of the Rx code which have been split in two implementations with
the addition of RZ/G2L support, a device that supports larger frame
sizes.
This change removes the need for duplicated and somewhat inaccurate
hardware alignment constrains stored in the hardware information struct
by creating a helper to handle the allocation of an skb and alignment of
an skb data.
For the R-Car class of devices the maximum frame size is 4K and each
descriptor is limited to 2K of data. The current implementation does not
support split descriptors, this limits the frame size to 2K. The
current hardware information however records the descriptor size just
under 2K due to bad understanding of the device when larger MTUs where
added.
For the RZ/G2L device the maximum frame size is 8K and each descriptor
is limited to 4K of data. The current hardware information records this
correctly, but it gets the alignment constrains wrong as just aligns it
by 128, it does not extend it by 128 bytes to allow the full frame to be
stored. This works because the RZ/G2L device supports split descriptors
and allocates each skb to 8K and aligns each 4K descriptor in this
space.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct member rx_max_buf_size was added before split descriptor
support was added. It is unclear if the value describes the full skb
frame buffer or the data descriptor buffer which can be combined into a
single skb.
Rename it to make it clear it referees to the maximum frame size and can
cover multiple descriptors.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx ring can either be made up of normal or extended descriptors, not
a mix of the two at the same time. Make this explicit by grouping the
two variables in a rx_ring union.
The extension of the storage for more than one queue of normal
descriptors from a single to NUM_RX_QUEUE queues have no practical
effect. But aids in making the code readable as the code that uses it
already piggyback on other members of struct ravb_private that are
arrays of max length NUM_RX_QUEUE, e.g. rx_desc_dma. This will also make
further refactoring easier.
While at it, rename the normal descriptor Rx ring to make it clear it's
not strictly related to the GbEthernet E-MAC IP found in RZ/G2L, normal
descriptors could be used on R-Car SoCs too.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
From: Tony Nguyen <anthony.l.nguyen@intel.com>
To: davem@davemloft.net, kuba@kernel.org, pabeni@redhat.com,
edumazet@google.com, netdev@vger.kernel.org
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>, alan.brady@intel.com
Tony Nguyen says:
====================
idpf: refactor virtchnl messages
Alan Brady says:
The motivation for this series has two primary goals. We want to enable
support of multiple simultaneous messages and make the channel more
robust. The way it works right now, the driver can only send and receive
a single message at a time and if something goes really wrong, it can
lead to data corruption and strange bugs.
To start the series, we introduce an idpf_virtchnl.h file. This reduces
the burden on idpf.h which is overloaded with struct and function
declarations.
The conversion works by conceptualizing a send and receive as a
"virtchnl transaction" (idpf_vc_xn) and introducing a "transaction
manager" (idpf_vc_xn_manager). The vcxn_mngr will init a ring of
transactions from which the driver will pop from a bitmap of free
transactions to track in-flight messages. Instead of needing to handle a
complicated send/recv for every a message, the driver now just needs to
fill out a xn_params struct and hand it over to idpf_vc_xn_exec which
will take care of all the messy bits. Once a message is sent and
receives a reply, we leverage the completion API to signal the received
buffer is ready to be used (assuming success, or an error code
otherwise).
At a low-level, this implements the "sw cookie" field of the virtchnl
message descriptor to enable this. We have 16 bits we can put whatever
we want and the recipient is required to apply the same cookie to the
reply for that message. We use the first 8 bits as an index into the
array of transactions to enable fast lookups and we use the second 8
bits as a salt to make sure each cookie is unique for that message. As
transactions are received in arbitrary order, it's possible to reuse a
transaction index and the salt guards against index conflicts to make
certain the lookup is correct. As a primitive example, say index 1 is
used with salt 1. The message times out without receiving a reply so
index 1 is renewed to be ready for a new transaction, we report the
timeout, and send the message again. Since index 1 is free to be used
again now, index 1 is again sent but now salt is 2. This time we do get
a reply, however it could be that the reply is _actually_ for the
previous send index 1 with salt 1. Without the salt we would have no
way of knowing for sure if it's the correct reply, but with we will know
for certain.
Through this conversion we also get several other benefits. We can now
more appropriately handle asynchronously sent messages by providing
space for a callback to be defined. This notably allows us to handle MAC
filter failures better; previously we could potentially have stale,
failed filters in our list, which shouldn't really have a major impact
but is obviously not correct. I also managed to remove fairly
significant more lines than I added which is a win in my book.
Additionally, this converts some variables to use auto-variables where
appropriate. This makes the alloc paths much cleaner and less prone to
memory leaks. We also fix a few virtchnl related bugs while we're here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-05 (idpf, ice, i40e, igc, e1000e)
This series contains updates to idpf, ice, i40e, igc and e1000e drivers.
Emil disables local BH on NAPI schedule for proper handling of softirqs
on idpf.
Jake stops reporting of virtchannel RSS option which in unsupported on
ice.
Rand Deeb adds null check to prevent possible null pointer dereference
on ice.
Michal Schmidt moves DPLL mutex initialization to resolve uninitialized
mutex usage for ice.
Jesse fixes incorrect variable usage for calculating Tx stats on ice.
Ivan Vecera corrects logic for firmware equals check on i40e.
Florian Kauer prevents memory corruption for XDP_REDIRECT on igc.
Sasha reverts an incorrect use of FIELD_GET which caused a regression
for Wake on LAN on e1000e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
fec_enet_adjust_link() which gets called by phylib when there is a
change in link status.
fec_enet_set_eee() now just stores away the LPI timer value.
Everything else is passed to phylib, so it can correctly setup the
PHY.
fec_enet_get_eee() relies on phylib doing most of the work,
the MAC driver just adds the LPI timer value.
Call phy_support_eee() if the quirk is present to indicate the MAC
actually supports EEE.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> (On iMX8MP debix)
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FEC is about to get its EEE code re-written. To allow this, move
fec_enet_eee_mode_set() before fec_enet_adjust_link() which will
need to call it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20240302195306.3207716-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Older versions of GCC really want to know the full definition
of the type involved in rcu_assign_pointer().
struct dpll_pin is defined in a local header, net/core can't
reach it. Move all the netdev <> dpll code into dpll, where
the type is known. Otherwise we'd need multiple function calls
to jump between the compilation units.
This is the same problem the commit under fixes was trying to address,
but with rcu_assign_pointer() not rcu_dereference().
Some of the exports are not needed, networking core can't
be a module, we only need exports for the helpers used by
drivers.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/all/35a869c8-52e8-177-1d4d-e57578b99b6@linux-m68k.org/
Fixes: 640f41ed33b5 ("dpll: fix build failure due to rcu_dereference_check() on unknown type")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240305013532.694866-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the hnae_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240302-class_cleanup-net-next-v1-1-8fa378595b93@marliere.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactoring of the field get conversion introduced a regression in the
legacy Wake On Lan from a magic packet with i219 devices. Rx address
copied not correctly from MAC to PHY with FIELD_GET macro.
Fixes: b9a452545075 ("intel: legacy: field get conversion")
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When a frame can not be transmitted in XDP_REDIRECT
(e.g. due to a full queue), it is necessary to free
it by calling xdp_return_frame_rx_napi.
However, this is the responsibility of the caller of
the ndo_xdp_xmit (see for example bq_xmit_all in
kernel/bpf/devmap.c) and thus calling it inside
igc_xdp_xmit (which is the ndo_xdp_xmit of the igc
driver) as well will lead to memory corruption.
In fact, bq_xmit_all expects that it can return all
frames after the last successfully transmitted one.
Therefore, break for the first not transmitted frame,
but do not call xdp_return_frame_rx_napi in igc_xdp_xmit.
This is equally implemented in other Intel drivers
such as the igb.
There are two alternatives to this that were rejected:
1. Return num_frames as all the frames would have been
transmitted and release them inside igc_xdp_xmit.
While it might work technically, it is not what
the return value is meant to represent (i.e. the
number of SUCCESSFULLY transmitted packets).
2. Rework kernel/bpf/devmap.c and all drivers to
support non-consecutively dropped packets.
Besides being complex, it likely has a negative
performance impact without a significant gain
since it is anyway unlikely that the next frame
can be transmitted if the previous one was dropped.
The memory corruption can be reproduced with
the following script which leads to a kernel panic
after a few seconds. It basically generates more
traffic than a i225 NIC can transmit and pushes it
via XDP_REDIRECT from a virtual interface to the
physical interface where frames get dropped.
#!/bin/bash
INTERFACE=enp4s0
INTERFACE_IDX=`cat /sys/class/net/$INTERFACE/ifindex`
sudo ip link add dev veth1 type veth peer name veth2
sudo ip link set up $INTERFACE
sudo ip link set up veth1
sudo ip link set up veth2
cat << EOF > redirect.bpf.c
SEC("prog")
int redirect(struct xdp_md *ctx)
{
return bpf_redirect($INTERFACE_IDX, 0);
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c redirect.bpf.c -o redirect.bpf.o
sudo ip link set veth2 xdp obj redirect.bpf.o
cat << EOF > pass.bpf.c
SEC("prog")
int pass(struct xdp_md *ctx)
{
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
EOF
clang -O2 -g -Wall -target bpf -c pass.bpf.c -o pass.bpf.o
sudo ip link set $INTERFACE xdp obj pass.bpf.o
cat << EOF > trafgen.cfg
{
/* Ethernet Header */
0xe8, 0x6a, 0x64, 0x41, 0xbf, 0x46,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 1, 1, # IP Src - adapt as needed
10, 0, 1, 2, # IP Dest - adapt as needed
const16(6666), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
EOF
sudo trafgen -i trafgen.cfg -b3000MB -o veth1 --cpp
Fixes: 4ff320361092 ("igc: Add support for XDP_REDIRECT action")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Helper i40e_is_fw_ver_eq() compares incorrectly given firmware version
as it returns true when the major version of running firmware is
greater than the given major version that is wrong and results in
failure during getting of DCB configuration where this helper is used.
Fix the check and return true only if the running FW version is exactly
equals to the given version.
Reproducer:
1. Load i40e driver
2. Check dmesg output
[root@host ~]# modprobe i40e
[root@host ~]# dmesg | grep 'i40e.*DCB'
[ 74.750642] i40e 0000:02:00.0: Query for DCB configuration failed, err -EIO aq_err I40E_AQ_RC_EINVAL
[ 74.759770] i40e 0000:02:00.0: DCB init failed -5, disabled
[ 74.966550] i40e 0000:02:00.1: Query for DCB configuration failed, err -EIO aq_err I40E_AQ_RC_EINVAL
[ 74.975683] i40e 0000:02:00.1: DCB init failed -5, disabled
Fixes: cf488e13221f ("i40e: Add other helpers to check version of running firmware and AQ API")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix an obviously incorrect assignment, created with a typo or cut-n-paste
error.
Fixes: 5995ef88e3a8 ("ice: realloc VSI stats arrays")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The pf->dplls.lock mutex is initialized too late, after its first use.
Move it to the top of ice_dpll_init.
Note that the "err_exit" error path destroys the mutex. And the mutex is
the last thing destroyed in ice_dpll_deinit.
This fixes the following warning with CONFIG_DEBUG_MUTEXES:
ice 0000:10:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.36.0
ice 0000:10:00.0: 252.048 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x16 link)
ice 0000:10:00.0: PTP init successful
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 410 at kernel/locking/mutex.c:587 __mutex_lock+0x773/0xd40
Modules linked in: crct10dif_pclmul crc32_pclmul crc32c_intel polyval_clmulni polyval_generic ice(+) nvme nvme_c>
CPU: 0 PID: 410 Comm: kworker/0:4 Not tainted 6.8.0-rc5+ #3
Hardware name: HPE ProLiant DL110 Gen10 Plus/ProLiant DL110 Gen10 Plus, BIOS U56 10/19/2023
Workqueue: events work_for_cpu_fn
RIP: 0010:__mutex_lock+0x773/0xd40
Code: c0 0f 84 1d f9 ff ff 44 8b 35 0d 9c 69 01 45 85 f6 0f 85 0d f9 ff ff 48 c7 c6 12 a2 a9 85 48 c7 c7 12 f1 a>
RSP: 0018:ff7eb1a3417a7ae0 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 0000000000000002 RSI: ffffffff85ac2bff RDI: 00000000ffffffff
RBP: ff7eb1a3417a7b80 R08: 0000000000000000 R09: 00000000ffffbfff
R10: ff7eb1a3417a7978 R11: ff32b80f7fd2e568 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ff32b7f02c50e0d8
FS: 0000000000000000(0000) GS:ff32b80efe800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055b5852cc000 CR3: 000000003c43a004 CR4: 0000000000771ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
? __warn+0x84/0x170
? __mutex_lock+0x773/0xd40
? report_bug+0x1c7/0x1d0
? prb_read_valid+0x1b/0x30
? handle_bug+0x42/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __mutex_lock+0x773/0xd40
? rcu_is_watching+0x11/0x50
? __kmalloc_node_track_caller+0x346/0x490
? ice_dpll_lock_status_get+0x28/0x50 [ice]
? __pfx_ice_dpll_lock_status_get+0x10/0x10 [ice]
? ice_dpll_lock_status_get+0x28/0x50 [ice]
ice_dpll_lock_status_get+0x28/0x50 [ice]
dpll_device_get_one+0x14f/0x2e0
dpll_device_event_send+0x7d/0x150
dpll_device_register+0x124/0x180
ice_dpll_init_dpll+0x7b/0xd0 [ice]
ice_dpll_init+0x224/0xa40 [ice]
? _dev_info+0x70/0x90
ice_load+0x468/0x690 [ice]
ice_probe+0x75b/0xa10 [ice]
? _raw_spin_unlock_irqrestore+0x4f/0x80
? process_one_work+0x1a3/0x500
local_pci_probe+0x47/0xa0
work_for_cpu_fn+0x17/0x30
process_one_work+0x20d/0x500
worker_thread+0x1df/0x3e0
? __pfx_worker_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
irq event stamp: 125197
hardirqs last enabled at (125197): [<ffffffff8416409d>] finish_task_switch.isra.0+0x12d/0x3d0
hardirqs last disabled at (125196): [<ffffffff85134044>] __schedule+0xea4/0x19f0
softirqs last enabled at (105334): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
softirqs last disabled at (105332): [<ffffffff84e1e65a>] napi_get_frags_check+0x1a/0x60
---[ end trace 0000000000000000 ]---
Fixes: d7999f5ea64b ("ice: implement dpll interface to control cgu")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The function ice_bridge_setlink() may encounter a NULL pointer dereference
if nlmsg_find_attr() returns NULL and br_spec is dereferenced subsequently
in nla_for_each_nested(). To address this issue, add a check to ensure that
br_spec is not NULL before proceeding with the nested attribute iteration.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink")
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E800 series hardware uses the same iAVF driver as older devices,
including the virtchnl negotiation scheme.
This negotiation scheme includes a mechanism to determine what type of RSS
should be supported, including RSS over PF virtchnl messages, RSS over
firmware AdminQ messages, and RSS via direct register access.
The PF driver will always prefer VIRTCHNL_VF_OFFLOAD_RSS_PF if its
supported by the VF driver. However, if an older VF driver is loaded, it
may request only VIRTCHNL_VF_OFFLOAD_RSS_REG or VIRTCHNL_VF_OFFLOAD_RSS_AQ.
The ice driver happily agrees to support these methods. Unfortunately, the
underlying hardware does not support these mechanisms. The E800 series VFs
don't have the appropriate registers for RSS_REG. The mailbox queue used by
VFs for VF to PF communication blocks messages which do not have the
VF-to-PF opcode.
Stop lying to the VF that it could support RSS over AdminQ or registers, as
these interfaces do not work when the hardware is operating on an E800
series device.
In practice this is unlikely to be hit by any normal user. The iAVF driver
has supported RSS over PF virtchnl commands since 2016, and always defaults
to using RSS_PF if possible.
In principle, nothing actually stops the existing VF from attempting to
access the registers or send an AQ command. However a properly coded VF
will check the capability flags and will report a more useful error if it
detects a case where the driver does not support the RSS offloads that it
does.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix softirq's not being handled during napi_schedule() call when
receiving marker packets for queue disable by disabling local bottom
half.
The issue can be seen on ifdown:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using ftrace to catch the failing scenario:
ifconfig [003] d.... 22739.830624: softirq_raise: vec=3 [action=NET_RX]
<idle>-0 [003] ..s.. 22739.831357: softirq_entry: vec=3 [action=NET_RX]
No interrupt and CPU is idle.
After the patch when disabling local BH before calling napi_schedule:
ifconfig [003] d.... 22993.928336: softirq_raise: vec=3 [action=NET_RX]
ifconfig [003] ..s1. 22993.928337: softirq_entry: vec=3 [action=NET_RX]
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When draining a page_frag_cache, most user are doing
the similar steps, so introduce an API to avoid code
duplication.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GPIO EOI is not set to clear interrupt status after handling the
interrupt. It should be done in irq_chip->irq_ack, but this function
is not called in handle_nested_irq(). So executing function
txgbe_gpio_irq_ack() manually in txgbe_gpio_irq_handler().
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The register of GPIO interrupt status is masked before MAC IRQ
is enabled. This is because of hardware deficiency. So manually
clear the interrupt status before using them. Otherwise, GPIO
interrupts will never be reported again. There is a workaround for
clearing interrupts to set GPIO EOI in txgbe_up_complete().
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-03-01
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2024-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Switch to using _bh variant of of spinlock API in port timestamping NAPI poll context
net/mlx5e: Use a memory barrier to enforce PTP WQ xmit submission tracking occurs after populating the metadata_map
net/mlx5e: Fix MACsec state loss upon state update in offload path
net/mlx5e: Change the warning when ignore_flow_level is not supported
net/mlx5: Check capability for fw_reset
net/mlx5: Fix fw reporter diagnose output
net/mlx5: E-switch, Change flow rule destination checking
Revert "net/mlx5e: Check the number of elements before walk TC rhashtable"
Revert "net/mlx5: Block entering switchdev mode with ns inconsistency"
====================
Link: https://lore.kernel.org/r/20240302070318.62997-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-01 (ixgbe, i40e, ice)
This series contains updates to ixgbe, i40e, and ice drivers.
Maciej corrects disable flow for ixgbe, i40e, and ice drivers which could
cause non-functional interface with AF_XDP.
Michal restores host configuration when changing MSI-X count for VFs on
ice driver.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: reconfig host after changing MSI-X on VF
ice: reorder disabling IRQ and NAPI in ice_qp_dis
i40e: disable NAPI right after disabling irqs when handling xsk_pool
ixgbe: {dis, en}able irqs in ixgbe_txrx_ring_{dis, en}able
====================
Link: https://lore.kernel.org/r/20240301192549.2993798-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add curly braces to avoid entering to an if statement where it is not
always required in e1000_shutdown function.
This improves code readability and might prevent non-deterministic
behaviour in the future.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When IGC is built-in but LEDS_CLASS is a loadable module, there is
a link failure:
x86_64-linux-ld: drivers/net/ethernet/intel/igc/igc_leds.o: in function `igc_led_setup':
igc_leds.c:(.text+0x75c): undefined reference to `devm_led_classdev_register_ext'
Add another dependency that prevents this combination.
Fixes: ea578703b03d ("igc: Add support for LEDs on i225/i226")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Added support for 1000BASE-BX, i.e. Gigabit Ethernet over single strand
of single-mode fiber.
The initialization of a 1000BASE-BX SFP is the same as 1000BASE-SX/LX
with the only difference that the Bit Rate Nominal Value must be
checked to make sure it is a Gigabit Ethernet transceiver, as described
by the SFF-8472 specification.
This was tested with the FS.com SFP-GE-BX 1310/1490nm 10km transceiver:
$ ethtool -m eth4
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x40 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: BASE-BX10
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 10km
Length (SMF) : 10000m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 1310nm
Vendor name : FS
Vendor OUI : 64:9d:99
Vendor PN : SFP-GE-BX
Vendor rev :
Option values : 0x20 0x0a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : Power level 3 requirement
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : S2202359108
Date code : 220307
Optical diagnostics support : Yes
Laser bias current : 17.650 mA
Laser output power : 0.2132 mW / -6.71 dBm
Receiver signal average optical power : 0.2740 mW / -5.62 dBm
Module temperature : 47.30 degrees C / 117.13 degrees F
Module voltage : 3.2576 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : Off
Laser bias current low alarm : Off
Laser bias current high warning : Off
Laser bias current low warning : Off
Laser output power high alarm : Off
Laser output power low alarm : Off
Laser output power high warning : Off
Laser output power low warning : Off
Module temperature high alarm : Off
Module temperature low alarm : Off
Module temperature high warning : Off
Module temperature low warning : Off
Module voltage high alarm : Off
Module voltage low alarm : Off
Module voltage high warning : Off
Module voltage low warning : Off
Laser rx power high alarm : Off
Laser rx power low alarm : Off
Laser rx power high warning : Off
Laser rx power low warning : Off
Laser bias current high alarm threshold : 110.000 mA
Laser bias current low alarm threshold : 1.000 mA
Laser bias current high warning threshold : 100.000 mA
Laser bias current low warning threshold : 1.000 mA
Laser output power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser output power low alarm threshold : 0.0891 mW / -10.50 dBm
Laser output power high warning threshold : 0.6310 mW / -2.00 dBm
Laser output power low warning threshold : 0.1000 mW / -10.00 dBm
Module temperature high alarm threshold : 90.00 degrees C / 194.00 degrees F
Module temperature low alarm threshold : -45.00 degrees C / -49.00 degrees F
Module temperature high warning threshold : 85.00 degrees C / 185.00 degrees F
Module temperature low warning threshold : -40.00 degrees C / -40.00 degrees F
Module voltage high alarm threshold : 3.7950 V
Module voltage low alarm threshold : 2.8050 V
Module voltage high warning threshold : 3.4650 V
Module voltage low warning threshold : 3.1350 V
Laser rx power high alarm threshold : 0.7079 mW / -1.50 dBm
Laser rx power low alarm threshold : 0.0028 mW / -25.53 dBm
Laser rx power high warning threshold : 0.6310 mW / -2.00 dBm
Laser rx power low warning threshold : 0.0032 mW / -24.95 dBm
Signed-off-by: Ernesto Castellotti <ernesto@castellotti.net>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Linux users sometimes need an easy way to check current values of module
parameters. For example the module may be manually reloaded with different
parameters. Make these visible and readable in the /sys filesystem to allow
that. But don't make the "debug" module parameter visible as debugging is
enabled via ethtool msglvl.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Based on the static analyzis of the code it looks like when an entry
from the MAC table was removed, the entry was still used after being
freed. More precise the vid of the mac_entry was used after calling
devm_kfree on the mac_entry.
The fix consists in first using the vid of the mac_entry to delete the
entry from the HW and after that to free it.
Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240301080608.3053468-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
1. pcaps are free'd right after AQ routines are done, no need for
devm_'s
2. a test frame for loopback test in ethtool -t is destroyed at the end
of the test so we don't need devm_ here either.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_down() clears QINT_TQCTL_CAUSE_ENA_M bit twice, which is not
necessary. First clearing happens in ice_vsi_dis_irq() and second in
ice_vsi_stop_tx_ring() - remove the first one.
While at it, make ice_vsi_dis_irq() static as ice_down() is the only
current caller of it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The indentation for ice_set_ctx and ice_write_rxq_ctx breaks the function
name after the return type. This style of breaking is used a lot throughout
the ice driver, even in cases where its not actually helpful for
readability. We no longer prefer this style of line splitting in the
driver, and new code is avoiding it.
Normally, I would leave this alone unless the actual function contents or
description needed updating. However, a future change is going to add
inverse functions for converting packed context to unpacked context
structures. To keep this code uniform with the existing set functions, fix
up the style to the modern format of keeping the type on the same line.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
