summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2020-09-11net: ag71xx: add flow control supportOleksij Rempel
Add flow control support. The functionality was tested on AR9331 SoC and confirmed by iperf3 results and HW counters exported over ethtool. Following test configurations was used: iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender The switch is supporting symmytric flow control: Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full --->> Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: on Port: MII PHYAD: 4 Transceiver: external Link detected: yes The iMX6S system was configured to 10Mbit, to let the switch use flow control: - ethtool -s eth0 speed 10 With flow control disabled on AR9331: - ethtool -A eth0 rx off tx off - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender [ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver With flow control enabled on AR9331: - ethtool -A eth0 rx on tx on - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender [ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver Similar results are get in opposite direction by introducing extra CPU load on AR9331: - chrt 40 dd if=/dev/zero of=/dev/null & Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ag71xx: add ethtool supportOleksij Rempel
Add basic ethtool support. The functionality was tested on AR9331 SoC. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: stmmac: set get_rx_header_len() as void for it didn't have any error ↵Luo Jiaxing
code to return We found the following warning when using W=1 to build kernel: drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] int ret, coe = priv->hw->rx_csum; When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and dwxgmac2_get_rx_header_len() return 0 only, without any error code to report. Therefore, it's better to define get_rx_header_len() as void. Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Enable Link Speed Reporting in the driver.David Awogbemila
This change allows the driver to report the device link speed when the ethtool command: ethtool <nic name> is run. Getting the link speed is done via a new admin queue command: ReportLinkSpeed. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Use link status register to report link statusPatricio Noyola
This makes the driver better aware of the connectivity status of the device. Based on the device's status register, the driver can call netif_carrier_{on,off}. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Patricio Noyola <patricion@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Batch AQ commands for creating and destroying queues.Sagi Shahar
Adds support for batching AQ commands and uses it for creating and destroying queues. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Sagi Shahar <sagis@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: NIC stats for report-stats and for ethtoolDavid Awogbemila
This adds per queue NIC stats to ethtool stats and to report-stats. These stats are always exposed to guest whether or not the report-stats flag is turned on. Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.Kuo Zhao
This adds functionality to report driver stats to Hypervisor. (Users may want to turn this feature off as a matter of privacy so a "report-stats" flag is added as an ethtool priv option. It is also disabled by default.) The hypervisor would trigger a stats report in case "too many" packets dropped; the stats would be useful in debugging stuck queues. A "stats_report_trigger_cnt" stat is added to count the number of times the hypervisor attempts to trigger stats report. A timer is also added so that when report-stats is enabled, stat are updated once every 20 seconds. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Use dev_info/err instead of netif_info/err.Catherine Sullivan
Update the driver to use dev_info/err instead of netif_info/err. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Add stats for gve.Kuo Zhao
Sample output of "ethtool -S <interface-name>" with 1 RX queue and 1 TX queue: NIC statistics: rx_packets: 1039 tx_packets: 37 rx_bytes: 822071 tx_bytes: 4100 rx_dropped: 0 tx_dropped: 0 tx_timeouts: 0 rx_skb_alloc_fail: 0 rx_buf_alloc_fail: 0 rx_desc_err_dropped_pkt: 0 interface_up_cnt: 1 interface_down_cnt: 0 reset_cnt: 0 page_alloc_fail: 0 dma_mapping_error: 0 rx_posted_desc[0]: 1365 rx_completed_desc[0]: 341 rx_bytes[0]: 215094 rx_dropped_pkt[0]: 0 rx_copybreak_pkt[0]: 3 rx_copied_pkt[0]: 3 tx_posted_desc[0]: 6 tx_completed_desc[0]: 6 tx_bytes[0]: 420 tx_wake[0]: 0 tx_stop[0]: 0 tx_event_counter[0]: 6 adminq_prod_cnt: 34 adminq_cmd_fail: 0 adminq_timeouts: 0 adminq_describe_device_cnt: 1 adminq_cfg_device_resources_cnt: 1 adminq_register_page_list_cnt: 16 adminq_unregister_page_list_cnt: 0 adminq_create_tx_queue_cnt: 8 adminq_create_rx_queue_cnt: 8 adminq_destroy_tx_queue_cnt: 0 adminq_destroy_rx_queue_cnt: 0 adminq_dcfg_device_resources_cnt: 0 adminq_set_driver_parameter_cnt: 0 Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Get and set Rx copybreak via ethtoolKuo Zhao
This adds support for getting and setting the RX copybreak value via ethtool. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11qede: Notify qedr when mtu has changedMichal Kalderon
MTU change on ethtool is currently not supported for iWARP. Notify qedr driver so that appropriate logging can take place. Link: https://lore.kernel.org/r/20200902165741.8355-6-michal.kalderon@marvell.com Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2020-09-11RDMA/qedr: Remove fbo and zbva from the MRJason Gunthorpe
zbva is always false, so fbo is never read. A 'zero-based-virtual-address' is simply IOVA == 0, and the driver already supports this. Link: https://lore.kernel.org/r/16-v2-270386b7e60b+28f4-umem_1_jgg@nvidia.com Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2020-09-10net: smc91x: Remove set but not used variable 'status' in smc_phy_configure()Luo Jiaxing
Fixes the following warning when using W=1 to build kernel: drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_phy_configure’: drivers/net/ethernet/smsc/smc91x.c:1039:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] int status; Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: dec: de2104x: Increase receive ring size for TulipLucy Yan
Increase Rx ring size to address issue where hardware is reaching the receive work limit. Before: [ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached Signed-off-by: Lucy Yan <lucyyan@google.com> Reviewed-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix a kernel-doc warning in hinic_hw_eqs.cWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c:115: warning: Excess function parameter 'hw_handler' description in 'hinic_aeq_register_hw_cb' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix a kernel-doc warning in hinic_hw_api_cmd.cWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c:382: warning: Excess function parameter 'size' description in 'api_cmd' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix some kernel-doc warnings in hns_enet.cWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'netdev' description in 'hns_set_multicast_list' drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'p' description in 'hns_set_multicast_list' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix some kernel-doc warnings in hns_dsaf_xgmac.cWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:137: warning: Excess function parameter 'drv' description in 'hns_xgmac_enable' drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:497: warning: Excess function parameter 'cmd' description in 'hns_xgmac_get_regs' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: fix 'cdev' kernel-doc warning in hnae_ae_unregister()Wang Hai
Rename cdev to hdev. Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hnae.c:444: warning: Excess function parameter 'cdev' description in 'hnae_ae_unregister' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10hinic: Fix some kernel-doc warnings in hinic_hw_io.cWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'sq_msix_entry' description in 'hinic_io_create_qps' drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'rq_msix_entry' description in 'hinic_io_create_qps' Rename these wrong names. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: mvpp2: ptp: Fix unused variablesAlex Dewar
In the functions mvpp2_isr_handle_xlg() and mvpp2_isr_handle_gmac_internal(), the bool variable link is assigned a true value in the case that a given bit of val is set. However, if the bit is unset, no value is assigned to link and it is then passed to mvpp2_isr_handle_link() without being initialised. Fix by assigning to link the value of the bit test. Build-tested on x86. Fixes: 36cfd3a6e52b ("net: mvpp2: restructure "link status" interrupt handling") Signed-off-by: Alex Dewar <alex.dewar90@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: cxgb3: Fix some kernel-doc warningsWang Hai
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2209: warning: Excess function parameter 'adapter' description in 'clear_sge_ctxt' drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2975: warning: Excess function parameter 'adapter' description in 't3_set_proto_sram' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: ena: xdp: add queue counters for xdp actionsSameeh Jubran
When using XDP every ingress packet is passed to an eBPF (xdp) program which returns an action for this packet. This patch adds counters for the number of times each such action was received. It also counts all the invalid actions received from the eBPF program. Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: ena: ethtool: add stats printing to XDP queuesSameeh Jubran
Added statistics for TX queues that are used for XDP TX. The statistics are the same as the ones printed for regular non-XDP TX queues. The XDP queue statistics can be queried using `ethtool -S <ifname>` Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: ena: ethtool: Add new device statisticsSameeh Jubran
The new metrics provide granular visibility along multiple network dimensions and enable troubleshooting and remediation of issues caused by instances exceeding network performance allowances. The new statistics can be queried using ethtool command. Signed-off-by: Guy Tzalik <gtzalik@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: ena: ethtool: convert stat_offset to 64 bit resolutionSameeh Jubran
The type of all stat fields is u64, therefore when iterating over stat fields in a stats struct, it makes sense to use an offset in 64 bit resolution. Doing so allows us to drop some of the casting that is currently used when referencing stats. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: mvneta: fix possible use-after-free in mvneta_xdp_put_buffLorenzo Bianconi
Release first buffer as last one since it contains references to subsequent fragments. This code will be optimized introducing multi-buffer bit in xdp_buff structure. Fixes: ca0e014609f05 ("net: mvneta: move skb build after descriptors processing") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: mventa: drop mvneta_stats from mvneta_swbm_rx_frame signatureLorenzo Bianconi
Remove mvneta_stats from mvneta_swbm_rx_frame signature since now stats are accounted in mvneta_run_xdp routine Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: remove napi_hash_del() from driver-facing APIJakub Kicinski
We allow drivers to call napi_hash_del() before calling netif_napi_del() to batch RCU grace periods. This makes the API asymmetric and leaks internal implementation details. Soon we will want the grace period to protect more than just the NAPI hash table. Restructure the API and have drivers call a new function - __netif_napi_del() if they want to take care of RCU waits. Note that only core was checking the return status from napi_hash_del() so the new helper does not report if the NAPI was actually deleted. Some notes on driver oddness: - veth observed the grace period before calling netif_napi_del() but that should not matter - myri10ge observed normal RCU flavor - bnx2x and enic did not actually observe the grace period (unless they did so implicitly) - virtio_net and enic only unhashed Rx NAPIs The last two points seem to indicate that the calls to napi_hash_del() were a left over rather than an optimization. Regardless, it's easy enough to correct them. This patch may introduce extra synchronize_net() calls for interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on free_netdev() to call netif_napi_del(). This seems inevitable since we want to use RCU for netpoll dev->napi_list traversal, and almost no drivers set IFF_DISABLE_NETPOLL. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10mlx4: make sure to always set the port typeJakub Kicinski
Even tho mlx4_core registers the devlink ports, it's mlx4_en and mlx4_ib which set their type. In situations where one of the two is not built yet the machine has ports of given type we see the devlink warning from devlink_port_type_warn() trigger. Having ports of a type not supported by the kernel may seem surprising, but it does occur in practice - when the unsupported port is not plugged in to a switch anyway users are more than happy not to see it (and potentially allocate any resources to it). Set the type in mlx4_core if type-specific driver is not built. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: mvneta: rely on MVNETA_MAX_RX_BUF_SIZE for pkt split in ↵Lorenzo Bianconi
mvneta_swbm_rx_frame() In order to easily change the rx buffer size, rely on MVNETA_MAX_RX_BUF_SIZE instead of PAGE_SIZE in mvneta_swbm_rx_frame routine for rx buffer split. Currently this is not an issue since we set MVNETA_MAX_RX_BUF_SIZE to PAGE_SIZE - MVNETA_SKB_PAD but it is a good to have to configure a different rx buffer size. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09igc: Fix not considering the TX delay for timestampsVinicius Costa Gomes
When timestamping a packet there's a delay between the start of the packet and the point where the hardware actually captures the timestamp. This difference needs to be considered if we want accurate timestamps. This was done on the RX side, but not on the TX side. Fixes: 2c344ae24501 ("igc: Add support for TX timestamping") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-09igc: Fix wrong timestamp latency numbersVinicius Costa Gomes
The previous timestamping latency numbers were obtained by interpolating the i210 numbers with the i225 crystal clock value. That calculation was wrong. Use the correct values from real measurements. Fixes: 81b055205e8b ("igc: Add support for RX timestamping") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-09i40e: always propagate error value in i40e_set_vsi_promisc()Stefan Assmann
The for loop in i40e_set_vsi_promisc() reports errors via dev_err() but does not propagate the error up the call chain. Instead it continues the loop and potentially overwrites the reported error value. This results in the error being recorded in the log buffer, but the caller might never know anything went the wrong way. To avoid this situation i40e_set_vsi_promisc() needs to temporarily store the error after reporting it. This is still not optimal as multiple different errors may occur, so store the first error and hope that's the main issue. Fixes: 37d318d7805f (i40e: Remove scheduling while atomic possibility) Reported-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-09i40e: fix return of uninitialized aq_ret in i40e_set_vsi_promiscStefan Assmann
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function ‘i40e_set_vsi_promisc’: drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1176:14: error: ‘aq_ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized] i40e_status aq_ret; In case the code inside the if statement and the for loop does not get executed aq_ret will be uninitialized when the variable gets returned at the end of the function. Avoid this by changing num_vlans from int to u16, so aq_ret always gets set. Making this change in additional places as num_vlans should never be negative. Fixes: 37d318d7805f ("i40e: Remove scheduling while atomic possibility") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Acked-by: Jakub Kicinski <kuba@kernel.org> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-09net: qed: RDMA personality shouldn't fail VF loadDmitry Bogdanov
Fix the assert during VF driver installation when the personality is iWARP Fixes: 1fe614d10f45 ("qed: Relax VF firmware requirements") Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: qede: Disable aRFS for NPAR and 100GDmitry Bogdanov
In some configurations ARFS cannot be used, so disable it if device is not capable. Fixes: e4917d46a653 ("qede: Add aRFS support") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: qed: Disable aRFS for NPAR and 100GDmitry Bogdanov
In CMT and NPAR the PF is unknown when the GFS block processes the packet. Therefore cannot use searcher as it has a per PF database, and thus ARFS must be disabled. Fixes: d51e4af5c209 ("qed: aRFS infrastructure support") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: ptp: add support for transmit timestampingRussell King
Add support for timestamping transmit packets. We allocate SYNC messages to queue 1, every other message to queue 0. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: ptp: add support for receive timestampingRussell King
Add support for receive timestamping. When enabled, the hardware adds a timestamp into the receive queue descriptor for all received packets with no filtering. Hence, we can only support NONE or ALL receive filter modes. The timestamp in the receive queue contains two bit sof seconds and the full nanosecond timestamp. This has to be merged with the remainder of the seconds from the TAI clock to arrive at a full timestamp before we can convert it to a ktime for the skb hardware timestamp field. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: ptp: add TAI supportRussell King
Add support for the TAI block in the mvpp2.2 hardware. Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: check first level interrupt status registersRussell King
Check the first level interrupt status registers to determine how to further process the port interrupt. We will need this to know whether to invoke the link status processing and/or the PTP processing for both XLG and GMAC. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: rename mis-named "link status" interruptRussell King
The link interrupt is used for way more than just the link status; it comes from a collection of units to do with the port. The Marvell documentation describes the interrupt as "GOP port X interrupt". Since we are adding PTP support, and the PTP interrupt uses this, rename it to be more inline with the documentation. This interrupt is also mis-named in the DT binding, but we leave that alone. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: mvpp2: restructure "link status" interrupt handlingRussell King
The "link status" interrupt is used for more than just link status. Restructure mvpp2_link_status_isr() so we can add additional handling. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09devlink: Introduce controller numberParav Pandit
A devlink port may be for a controller consist of PCI device. A devlink instance holds ports of two types of controllers. (1) controller discovered on same system where eswitch resides This is the case where PCI PF/VF of a controller and devlink eswitch instance both are located on a single system. (2) controller located on external host system. This is the case where a controller is located in one system and its devlink eswitch ports are located in a different system. When a devlink eswitch instance serves the devlink ports of both controllers together, PCI PF/VF numbers may overlap. Due to this a unique phys_port_name cannot be constructed. For example in below such system controller-0 and controller-1, each has PCI PF pf0 whose eswitch ports can be present in controller-0. These results in phys_port_name as "pf0" for both. Similar problem exists for VFs and upcoming Sub functions. An example view of two controller systems: --------------------------------------------------------- | | | --------- --------- ------- ------- | ----------- | | vf(s) | | sf(s) | |vf(s)| |sf(s)| | | server | | ------- ----/---- ---/----- ------- ---/--- ---/--- | | pci rc |=== | pf0 |______/________/ | pf1 |___/_______/ | | connect | | ------- ------- | ----------- | | controller_num=1 (no eswitch) | ------|-------------------------------------------------- (internal wire) | --------------------------------------------------------- | devlink eswitch ports and reps | | ----------------------------------------------------- | | |ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 |ctrl-0 | | | |pf0 | pf0vfN | pf0sfN | pf1 | pf1vfN |pf1sfN | | | ----------------------------------------------------- | | |ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 |ctrl-1 | | | |pf1 | pf1vfN | pf1sfN | pf1 | pf1vfN |pf0sfN | | | ----------------------------------------------------- | | | | | | --------- --------- ------- ------- | | | vf(s) | | sf(s) | |vf(s)| |sf(s)| | | ------- ----/---- ---/----- ------- ---/--- ---/--- | | | pf0 |______/________/ | pf1 |___/_______/ | | ------- ------- | | | | local controller_num=0 (eswitch) | --------------------------------------------------------- An example devlink port for external controller with controller number = 1 for a VF 1 of PF 0: $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf controller 1 pfnum 0 vfnum 1 external true splittable false function: hw_addr 00:00:00:00:00:00 $ devlink port show pci/0000:06:00.0/2 -jp { "port": { "pci/0000:06:00.0/2": { "type": "eth", "netdev": "ens2f0pf0vf1", "flavour": "pcivf", "controller": 1, "pfnum": 0, "vfnum": 1, "external": true, "splittable": false, "function": { "hw_addr": "00:00:00:00:00:00" } } } } Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09devlink: Introduce external controller flagParav Pandit
A devlink eswitch port may represent PCI PF/VF ports of a controller. A controller either located on same system or it can be an external controller located in host where such NIC is plugged in. Add the ability for driver to specify if a port is for external controller. Use such flag in the mlx5_core driver. An example of an external controller having VF1 of PF0 belong to controller 1. $ devlink port show pci/0000:06:00.0/2 pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf pfnum 0 vfnum 1 external true splittable false function: hw_addr 00:00:00:00:00:00 $ devlink port show pci/0000:06:00.0/2 -jp { "port": { "pci/0000:06:00.0/2": { "type": "eth", "netdev": "ens2f0pf0vf1", "flavour": "pcivf", "pfnum": 0, "vfnum": 1, "external": true, "splittable": false, "function": { "hw_addr": "00:00:00:00:00:00" } } } } Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net/mlx5: E-switch, Read controller number from deviceParav Pandit
ECPF supports one external host controller. Read controller number from the device. Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: stmmac: dwmac-intel-plat: remove redundant null check before ↵Zhang Changzhong
clk_disable_unprepare() Because clk_prepare_enable() and clk_disable_unprepare() already checked NULL clock parameter, so the additional checks are unnecessary, just remove them. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-09net: pxa168_eth: remove redundant null check before clk_disable_unprepare()Zhang Changzhong
Because clk_prepare_enable() and clk_disable_unprepare() already checked NULL clock parameter, so the additional checks are unnecessary, just remove them. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-10-01 02:01:32 +0000