| Age | Commit message (Collapse) | Author |
|---|
|
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes: 140ce421217e ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes: 4cda7d8d7098 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variables 'max_frm' and 'tmp_mac_key' are being assigned,
but are never used,hence they are redundant and can be removed.
fix fllowing warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:461:6: warning: variable 'max_frm' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1685:31: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1855:41: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in dev_info message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For FW_PORT_ACTION_GET_PORT_INFO32 messages, the
u.info32.lstatus32_to_cbllen32 is 32-bit Big Endian.
We need to translate that to CPU Endian in order to
test F_FW_PORT_CMD_DCBXDIS32.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While cleaning the command queue, the value of the HEAD register is not
in the range of next_to_clean and next_to_use, meaning that this value
is invalid. This also means that there is a hardware error and the
hardware will trigger a reset soon. At this time we should return an
error code instead of 0, and HCLGE_STATE_CMD_DISABLE needs to be set to
prevent sending command again.
Fixes: 3ff504908f95 ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595a2 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
drivers/net/ethernet/neterion/Kconfig => "Exar devices"
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce95 ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit ab123fe071c9 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071c9 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b349 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a764 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b0a ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd66 ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Commit 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3eb ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'app' is dereferenced before used for the devlink trace point.
In case FW is buggy and sends a control message to a VF queue
we should make sure app is not NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
There are no in-tree callers of cn23xx_dump_iq_regs.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-27 (Vxlan updates)
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seems it was missed while adding for first net dev in dual-emac mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers of qed_set_gft_event_id_cm_hdr.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With system having a small memory (around 256MB), the state "cannot
allocate memory to refill with new buffer" is reach pretty quickly.
By this patch we changed buffer allocation method to a better handling of
this use case by avoiding memory allocation issues.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory: extract from a larger patch]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the checksum offload feature is not set, then there is no point to
check the status of the hardware.
[gregory: extract from a larger patch]
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of trying to allocate the exact amount of memory for each
descriptor use a page for each of them, it allows to simplify the
allocation management and increase the performance of the driver.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to improve the diagnostic in case of error, make the distinction
between refill error and skb allocation error. Also make the information
available through the ethtool state.
Based on the work of Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initial values were too small leading to poor performance when using
the software buffer management.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory: extract from a larger patch]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On year ago Rob Herring wanted to remove the data pointer from the
device_node structure[1]. The mvneta driver seemed to be the only one
which used (abused ?) it. However, the proposal of Rob to remove this
pointer from the driver introduced a regression, and I tested and fixed an
alternative way, but it was never submitted as a proper patch.
Now here it is: Instead of using the device_node structure ->data
pointer, we store the BM private data as the driver data of the BM
platform_device. The core mvneta code can retrieve it by doing a lookup
on which platform_device corresponds to the BM device tree node using
of_find_device_by_node(), and get its driver data
[1]https://www.spinics.net/lists/netdev/msg445197.html
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is incorrect to enable TX/RX queues (call by mvneta_port_up()) for
port without link. Indeed MTU change for interface without link causes TX
queues to stuck.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
[gregory.clement: adding Fixes tags and rewording commit log]
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events. Some SoCs have
a single interrupt, independent of the CPU. The driver handles this by
having a per CPU napi structure when there are per CPU interrupts, and
a global napi structure when there is a single interrupt.
When the napi core calls mvneta_poll(), it passes the napi
instance. This was not being propagated through the call chain, and
instead the per-cpu napi instance was passed to napi_gro_receive()
call. This breaks when there is a single global napi instance.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver gets notification for mtu change, driver does not handle it for
all RQs. It handles only RQ[0].
Fix is to use enic_change_mtu() interface to change mtu for vf.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type. This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.
Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.
Fixes: 1025351a88a4 ("nfp: add flower app")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove uplink representor netdevice private structure lookup, and use
mlx5 core handle directly from representor private structure to lookup
vxlan ports.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
|
|
Move vxlan logic and objects to mlx5 core dirver.
Since it going to be used from different mlx5 interfaces.
e.g. mlx5e PF NIC netdev and mlx5e E-Switch representors.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
|
