| Age | Commit message (Collapse) | Author |
|---|
|
This is the same patch as for ixgbe but applied differently according to
busy polling. See commit 5d6002b7b822c74 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Three late 4.4-rc fixes.
The first two were very small in terms of number of lines, the third
is more lines of change than I like this late in the cycle, but there
are positive test results from Avagotech and from my own test setup
with the target hardware, and given the problem was a 100% failure
case, I sent it through.
- A previous patch updated the mlx4 driver to use vmalloc when there
was not enough memory to get a contiguous region large enough for
our needs, so we need kvfree() whenever we free that item. We
missed one place, so fix that now.
- A previous patch added code to match incoming packets against a
specific device, but failed to compensate for devices that have
both InfiniBand and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to
bring up any vlan interfaces and would print out a circular locking
failure. Fix that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/be2net: Remove open and close entry points
RDMA/ocrdma: Depend on async link events from CNA
RDMA/ocrdma: Dispatch only port event when port state changes
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
IB/cma: cma_match_net_dev needs to take into account port_num
|
|
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Added the PCI IDs for the BCM57301 and BCM57402 controllers.
Signed-off-by: David Christensen <davidch@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware will return the ring group resource when we call
hwrm_func_qcaps(). To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0. When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs. Otherwise, subsequent ring changes on
the PF may not work correctly.
We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs. There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.
When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Use local variable pf for repeated access to this pointer.
2. The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured. We need to make sure we have the
resources before we enable NTUPLE. Add bnxt_rfs_capable() to do the
checking.
In addition, we need to do the same checking in ndo_fix_features(). As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.
Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem. To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If hardware completes single segment rx frames, don't bother setting
up all the GRO related fields. Pass the SKB up as a normal frame.
Reviewed-by: vasundhara volam <vvolam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also, no need to check for bp->rx_nr_rings as it is always >= 1. If the
allocation fails, it is not a fatal error and we can still proceed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rx_l4_csum_error is now incremented only when offload is enabled
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NC-SI firmware of type apeFW (10) is now supported.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary "if" statement before the "for" statement:
if (x) {
for (i = 0; i < x; i++)
...
}
Also, change the ring free function to return void as it only returns 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During remove_one, the driver should issue hwrm_func_drv_unrgtr
command to inform firmware that this function has been unloaded.
This is to let firmware keep track of driver present/absent state
when driver is gracefully unloaded. A keep alive timer is needed
later to keep track of driver state during abnormal shutdown.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qlcnic_dcb_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vlaue of RTL8168H PHY register "rg_saw_cnt" only valid from bit0 to bit13.
When read this register, add bitwise-anding its value with 0x3fff.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function "rtl8168h_2_hw_phy_config", there is a typo in setting
RTL8168H PHY parameter.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems. The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.
This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the Ethernet MAC driver supporting the three
different types of MACs: dTSEC, tGEC and mEMAC.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Data Path Acceleration Architecture Frame Manger Port Driver.
The FMan driver uses a module called "Port" to represent the physical
TX and RX ports.
Each FMan version has different number of physical ports.
This patch adds The FMan Port configuration, initialization and
runtime control routines for both TX and RX.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Storage Profiles contain parameters that are used
by the FMan for frame reception and transmission.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Data Path Acceleration Architecture Frame Manger MAC support.
This patch adds The FMan MAC configuration, initialization and
runtime control routines.
This patch contains support for these types of MACs:
- dTSEC: Three speed Ethernet controller (10/100/1000 Mbps)
- tGEC: 10G Ethernet controller (10 Gbps)
- mEMAC: Multi-rate Ethernet MAC (10/100/1000/10000 Mbps)
Different FMan revisions have different type and number of MACs.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Data Path Acceleration Architecture Frame Manger Driver.
The FMan embeds a series of hardware blocks that implement a group
of Ethernet interfaces. This patch adds The FMan configuration,
initialization and runtime control routines.
The FMan driver supports several hardware versions
differentiated by things like:
- Different type of MACs
- Number of MAC and ports
- Available resources
- Different hardware errata
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Frame Manager Multi-User RAM support.
This internal FMan memory block is used by the
FMan hardware modules, the management being made
through the generic allocator.
The FMan Internal memory, for example, is used for
allocating transmit and receive FIFOs.
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove deprecated module parameters, and mark one parameter as
deprecated.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CLIP is always enabled and hardware uses 2 TID entries instead of 4 for
IPv6 in CLIP mode.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad2d ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW is capable of 2 requestor endianness modes for standard 8 Bytes
atomic: BE (0x0) and host endianness (0x1). Read the supported modes
from hca atomic capabilities and configure HW to host endianness mode if
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SGE context congestion map changed from 4 to 8 priority per port
in T6 as there are only 2 channels.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In T6, MPS classification has a 512 deep TCAM to do the match lookup.
Each entry has 80x2b sets containing 48 bit MAC address, port number,
VLAN Valid/ID, VNI, lookup type (outer or inner packet header).
[71:48] bit locations are overloaded for outer vs. inner lookup types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updating Congestion Channel/Priority Map in Congestion Manager Context
for T6. In T6 port 0 is mapped to channel 0 and port 1 is mapped to
channel 1. For 2 port T4/T5 adapter, port 0 is mapped to channel 0,1 and
port 1 is mapped to channel 2,3
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ingress padding boundary values got changed for T6.
T5: 0=32B 1=64B 2=128B 3=256B 4=512B 5=1024B 6=2048B 7=4096B
T6: 0=8B 1=16B 2=32B 3=64B 4=128B 5=128B 6=256B 7=512B
Updating the driver to set the correct boundary values in SGE_CONTROL to
32B.
Also, need to take care of this fl alignment change when calculating the
next packet offset.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updated pm_stats code to display input FIFO wait (index 5) and read
latency (index 7) counters for T6 adapters
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on configuration the NIC may return errors for unprivileged
functions and/or VFs. Where these are expected and handled, reduce the
level of any output.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in an unprivileged function we expect some MC commands
to fail with permission errors. To avoid log spew downgrade these to
debug only.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are situations - mostly reset related - where our view of the
filter table differs from the hardware. In this case we may try and
remove filters that aren't actually installed. This isn't that
interesting in most situations, so downgrade the logging.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For unprivileged functions operations can be authorised by an admin
function. Extra steps are introduced to the MCDI protocol in this
situation - the initial response from the MCDI tells us that the
operation has been deferred, and we must retry when told. We then
receive an event telling us to retry.
Note that this provides only the functionality for the unprivileged
functions, not the handling of the administrative side.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After reboot the vswitch configuration from the PF may not be
complete before the VF attempts to restore filters. In that
case we see NO_EVB_PORT errors from the MC. Retry up to a time
limit or until a different result is seen.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce access functions to query NIC vport system_image_guid,
node_guid and qkey_viol_cntr.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A mlx5 Ethernet port must be explicitly enabled for RoCE.
When RoCE is not enabled on the port, the NIC will refuse to create
QPs attached to it and incoming RoCE packets will be considered by the
NIC as plain Ethernet packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Introduce a new function called mlx5_query_nic_vport_context().
This function gets all the NIC vport attributes from the device.
The MAC address is just one of the NIC vport attributes, so
mlx5_query_nic_vport_mac_address() is now just a wrapper function
above mlx5_query_nic_vport_context().
More NIC vport attributes will be used in following commits.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
