| Age | Commit message (Collapse) | Author |
|---|
|
Since commit b499ffb0a22c ("i40e: Look up MAC address in Open Firmware
or IDPROM"), we've had support for obtaining the MAC address
form Open Firmware or IDPROM.
This code relied on sending the Open Firmware address directly to the
device firmware instead of relying on our MAC/VLAN filter list. Thus,
a work around was introduced in commit b1b15df59232 ("i40e: Explicitly
write platform-specific mac address after PF reset")
We refactored the Open Firmware address enablement code in the ill-named
commit 41c4c2b50d52 ("i40e: allow look-up of MAC address from Open
Firmware or IDPROM")
Since this refactor, we no longer even set I40E_FLAG_PF_MAC. Further, we
don't need this work around, because we actually store the MAC address
as part of the MAC/VLAN filter hash. Thus, we will restore the address
correctly upon reset.
The refactor above failed to revert the workaround, so do that now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.
Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.
Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.
The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.
Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The X722 pf flag setup should happen before the VMDq RSS queue count is
initialized for VMDq VSI to get the right number of queues for RSS in
case of X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently i40evf_close() can return before state transitions to
__I40EVF_DOWN because of the latency involved in processing and
receiving response from PF driver and scheduling of VF watchdog_task.
Due to this inconsistency an immediate call to i40evf_open() fails
because state is still DOWN_PENDING.
When a VF interface is in up state and we try to add it as slave,
The bonding driver calls dev_close() and dev_open() in short duration
resulting in dev_open returning error. The ifenslave command needs
to be run again for dev_open to succeed.
This fix ensures that watchdog timer is scheduled immediately after
admin queue operations are scheduled in i40evf_down(). In addition a
wait condition is added at the end of i40evf_close so that function
wont return when state is still DOWN_PENDING. The timeout value is
chosen after some profiling and includes some buffer.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that the kernel supports double VLAN tags, we should at least play
nice. Adjust the max packet size to account for two VLAN tags, not just
one.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-08-24
This series includes updates to mlx5 core driver.
From Gal and Saeed, three cleanup patches.
From Matan, Low level flow steering improvements and optimizations,
- Use more efficient data structures for flow steering objects handling.
- Add tracepoints to flow steering operations.
- Overall these patches improve flow steering rule insertion rate by a
factor of seven in large scales (~50K rules or more).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We never set the error code in this function.
Fixes: eabf0fad81d5 ("net-next/hinic: Initialize api cmd resources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
txq_reclaim() does the normal transmit queue reclamation and
rxq_deinit() does the RX ring cleanup, none of these are packet drops,
so use dev_consume_skb() for both locations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3_tx() does the normal packet TX completion,
tigon3_dma_hwbug_workaround() and tg3_tso_bug() both need to allocate a
new SKB that is suitable to workaround HW bugs, and finally
tg3_free_rings() is doing ring cleanup. Use dev_consume_skb_any() for
these 3 locations to be SKB drop monitor friendly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case bcm_sysport_init_tx_ring() is not able to allocate ring->cbs, we
would return with an error, and call bcm_sysport_fini_tx_ring() and it
would see that ring->cbs is NULL and do nothing. This would leak the
coherent DMA descriptor area, so we need to free it on error before
returning.
Reported-by: Eric Dumazet <edumazet@gmail.com>
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 3 spots where we call dev_kfree_skb() but we are actually
just doing a normal SKB consumption: __bcmgenet_tx_reclaim() for normal
TX reclamation, bcmgenet_alloc_rx_buffers() during the initial RX ring
setup and bcmgenet_free_rx_buffers() during RX ring cleanup.
Fixes: d6707bec5986 ("net: bcmgenet: rewrite bcmgenet_rx_refill()")
Fixes: f48bed16a756 ("net: bcmgenet: Free skb after last Tx frag")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Utilize dev_consume_skb_any(cb->skb) in bcm_sysport_free_cb() which is
used when a TX packet is completed, as well as when the RX ring is
cleaned on shutdown. None of these two cases are packet drops, so be
drop monitor friendly.
Suggested-by: Eric Dumazet <edumazet@gmail.com>
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-8.0.0 (snapshot) points out that we copy a variable-length string
into a fixed length field using memcpy() with the destination length,
and that ends up copying whatever follows the string:
inlined from 'ql_core_dump' at drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:1106:2:
drivers/net/ethernet/qlogic/qlge/qlge_dbg.c:708:2: error: 'memcpy' reading 15 bytes from a region of size 14 [-Werror=stringop-overflow=]
memcpy(seg_hdr->description, desc, (sizeof(seg_hdr->description)) - 1);
Changing it to use strncpy() will instead zero-pad the destination,
which seems to be the right thing to do here.
The bug is probably harmless, but it seems like a good idea to address
it in stable kernels as well, if only for the purpose of building with
gcc-8 without warnings.
Fixes: a61f80261306 ("qlge: Add ethtool register dump function.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make this const as it is only passed as an argument to the function
mlx5e_create_netdev and the corresponding argument is of type const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make these const as they are only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For XDP_REDIRECT the use of return code -EINVAL is confusing, as it is
used in three different cases. (1) When the index or ifindex lookup
fails, and in the ixgbe driver (2) when link is down and (3) when XDP
have not been enabled.
The return code can be picked up by the tracepoint xdp:xdp_redirect
for diagnosing why XDP_REDIRECT isn't working. Thus, there is a need
different return codes to tell the issues apart.
I'm considering using a specific err-code scheme for XDP_REDIRECT
instead of using these errno codes.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for controlling neighbor counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for IPv4 host table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for setting counters on neighbors based on dpipe's host table
counter status. This patch also adds the ability for getting the counter
value, which will be used by the dpipe host table implementation in the
next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is done as a preparation before introducing support for neighbor
counters. The flow counter's type enum is used by many registers, yet,
until now it was used only by mgpc and thus it was private. This patch
updates the namespace for more generic usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IPv4 host table initial support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change label name for case of erif table init failure.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is done as a preparation before introducing the ability to dump the
host table via dpipe, and to count the table size. The mlxsw's neighbor
representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix ERIF's table operations name space.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a tracepoint infrastructure for mlx5_core driver.
Implemented flow steering tracepoints:
1. Add flow group
2. Remove flow group
3. Add flow table entry
4. Remove flow table entry
5. Add flow table rule
6. Remove flow table rule
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When adding a flow table entry (fte) to a flow table (ft), we first
need to find its flow group (fg). Currently, this is done by
traversing a linear list of all flow groups in the flow table.
Furthermore, since multiple flow groups which correspond to the same
fte mask may exist in the same ft, we can't just stop at the first
match. Converting the linear list to rhltable in order to speed things
up.
The last four patches increases the steering rules update rate by a
factor of more than 7 (for insertion of 50K steering rules).
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When adding a flow table entry (fte) to a flow group (fg), we first
need to check whether this fte exist. In such a case we just merge
the destinations (if possible). Currently, this is done by traversing
the fte list available in a fg. This could take a lot of time when
using large flow groups. Speeding this up by using rhashtable, which
is much faster.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The current code stores fte_match_param in the software representation
of FTEs and FGs. fte_match_param contains a large reserved area at the
bottom of the struct. Since downstream patches are going to hash this
part, we would like to avoid doing so on a reserved part.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When allocating a flow table entry, we need to allocate a free index
in the flow group. Currently, this is done by traversing the existing
flow table entries in the flow group, until a free index is found.
Replacing this by using a ida, which allows us to find a free index
much faster.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix the following checkpatch warning in en_ethtool.c:
WARNING: suspect code indent for conditional statements (8, 9)
+ for (i = 0; i < NUM_PCIE_PERF_STALL_COUNTERS(priv); i++)
+ strcpy(data + (idx++) * ETH_GSTRING_LEN,
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The blank line should be after u32 val = ...
and not after __be32 __iomem *addr = ...
Fixes: ad5b39a95c83 ("net/mlx5: Add a blank line after declarations")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Joe Perches <joe@perches.com>
|
|
bnxt_hwrm_func_qcaps() is called during probe to get all device
resources and it also sets up the factory MAC address. The same function
is called when SRIOV is disabled to reclaim all resources. If
the MAC address has been overridden by a user administered MAC
address, calling this function will overwrite it.
Separate the logic that sets up the default MAC address into a new
function bnxt_init_mac_addr() that is only called during probe time.
Fixes: 4a21b49b34c0 ("bnxt_en: Improve VF resource accounting.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take back ownership of the MSIX vectors when unregistering the device
from bnxt_re.
Fixes: a588e4580a7e ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the number of TX rings is changed in bnxt_setup_tc(), we need to
include the XDP rings in the total TX ring count.
Fixes: 38413406277f ("bnxt_en: Add support for XDP_TX action.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TX completion may happen any time after HW queue was kicked.
We can't access the skb afterwards. Move the time stamping
before ringing the doorbell.
Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The functions set_ctrl0 and set_ctrl1 are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'set_ctrl0' was not declared. Should it be static?
symbol 'set_ctrl1' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If action is gact goto_chain, offload it to HW by jumping to another
ruleset.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to lookup ruleset in order to offload goto_chain termination
action. This patch adds it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For goto_chain action we need to know group_id of a ruleset to jump to.
Provide infrastructure in order to get it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reflect chain index coming down from TC core and create a ruleset per
chain. Note that only chain 0, being the implicit chain, is bound to the
device for processing. The rest of chains have to be "jumped-to" by
actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch uses the tso API to implement the tso functionality in Marvell
PPv2 driver.
Using iperf and 10G ports, using TSO shows a significant performance
improvement by a factor 2 to reach around 9.5Gbps in TX; as well as a
significant CPU usage drop (from 25% to 15%).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The txq size is defined by MVPP2_AGGR_TXQ_SIZE, which is sometime not
used directly but through variables. As it is a fixed value use the
define everywhere in the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver receives a muxed frame, but it can't find the representor
netdev it is destined to it will try to "drop" that frame, i.e. reuse
the buffer. The issue is that the replacement buffer has already been
allocated at this point, and reusing the buffer from received frame
will leak it. Change the code to put the new buffer on the ring
earlier and not reuse the old buffer (make the buffer parameter
to nfp_net_rx_drop() a NULL).
Fixes: 91bf82ca9eed ("nfp: add support for tx/rx with metadata portid")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
App start/stop callbacks can perform application initialization.
Unfortunately, flower app started using them for creating and
destroying representors. This can lead to a situation where
lower vNIC netdev is destroyed while representors still try
to pass traffic. This will most likely lead to a NULL-dereference
on the lower netdev TX path.
Move the start/stop callbacks, so that representors are created/
destroyed when vNICs are fully initialized.
Fixes: 5de73ee46704 ("nfp: general representor implementation")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling SR-IOV VFs will cause the PCI subsystem to schedule a
work and flush its workqueue. Since the nfp driver schedules its
own work we can't enable VFs while holding driver load. Commit
6d48ceb27af1 ("nfp: allocate a private workqueue for driver work")
tried to avoid this deadlock by creating a separate workqueue.
Unfortunately, due to the architecture of workqueue subsystem this
does not guarantee a separate thread of execution. Luckily
we can simply take pci_enable_sriov() from under the driver lock.
Take pci_disable_sriov() from under the lock too for symmetry.
Fixes: 6d48ceb27af1 ("nfp: allocate a private workqueue for driver work")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the NIC firmware, the 1-bit flag indicating "firmware is loaded" moved
from SLI_SCRATCH_1 to SLI_SCRATCH_2 (these are Octeon general-purpose
scratch registers). Make the PF driver conform to this change.
Remove code that sets the "firmware is loaded" flag because it's now the
firmware's job to do that.
In the code that detects whether or not the firmware is loaded, don't just
rely on checking the "firmware is loaded" flag because that may cause a
rare false negative. Add code that deduces whether or not the firmware is
loaded; that will never give a false negative.
Also bump up driver version to match newer NIC firmware.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using MII/GMII/SGMII in the Altera SoC, the phy needs to be
wired through the FPGA. To ensure correct behavior, the appropriate
bit in the System Manager FPGA Interface Group register needs to be
set.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
