| Age | Commit message (Collapse) | Author |
|---|
|
Add traps registration to mlx5_core devlink register/unregister flow.
This patch registers INGRESS_VLAN_FILTER trap.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add devlink traps infra-structure to mlx5 core driver. Add traps list to
mlx5_priv and corresponding API:
- mlx5_devlink_trap_report() to wrap trap reports to devlink
- mlx5_devlink_trap_get_num_active() to decide whether to open/close trap
resources.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-01-26
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
net/mlx5: Maintain separate page trees for ECPF and PF functions
net/mlx5e: Fix IPSEC stats
net/mlx5e: Reduce tc unsupported key print level
net/mlx5e: free page before return
net/mlx5e: E-switch, Fix rate calculation for overflow
net/mlx5: Fix memory leak on flow table creation error flow
====================
Link: https://lore.kernel.org/r/20210126234345.202096-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ensure that received Command-Response Queue (CRQ) entries are
properly read in order by the driver. dma_rmb barrier has
been added before accessing the CRQ descriptor to ensure
the entire descriptor is read before processing.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20210128013442.88319-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Anthony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-01-26
This series contains updates to the ice, i40e, and igc driver.
Henry corrects setting an unspecified protocol to IPPROTO_NONE instead of
0 for IPv6 flexbytes filters for ice.
Nick fixes the IPv6 extension header being processed incorrectly and
updates the netdev->dev_addr if it exists in hardware as it may have been
modified outside the ice driver.
Brett ensures a user cannot request more channels than available LAN MSI-X
and fixes the minimum allocation logic as it was incorrectly trying to use
more MSI-X than allocated for ice.
Stefan Assmann minimizes the delay between getting and using the VSI
pointer to prevent a possible crash for i40e.
Corinna Vinschen fixes link speed advertising for igc.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix link speed advertising
i40e: acquire VSI pointer only after VF is initialized
ice: Fix MSI-X vector fallback logic
ice: Don't allow more channels than LAN MSI-X available
ice: update dev_addr in ice_set_mac_address even if HW filter exists
ice: Implement flow for IPv6 next header (extension header)
ice: fix FDir IPv6 flexbyte
====================
Link: https://lore.kernel.org/r/20210126221035.658124-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following coccicheck warnings:
./drivers/net/ethernet/rocker/rocker_ofdpa.c:926:34-36: WARNING !A || A
&& B is equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611648783-3916-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rtl_wol_enable_rx() is called via the following call chain if WoL
is enabled:
rtl8169_down()
-> rtl_prepare_power_down()
-> rtl_wol_enable_rx()
Therefore we don't have to call this function here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/34ce78e2-596c-e2ac-16aa-c550fa624c22@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fec_restart() does a hard reset of the MAC module when the link status
changes to up. This temporarily resets the R_CNTRL register which controls
the MII mode of the ENET_OUT clock. In the case of RMII, the clock
frequency momentarily drops from 50MHz to 25MHz until the register is
reconfigured. Some link partners do not tolerate this glitch and
invalidate the link causing failure to establish a stable link when using
PHY polling mode. Since as per IEEE802.3 the criteria for link validity
are PHY-specific, what the partner should tolerate cannot be assumed, so
avoid resetting the MII clock by using software reset instead of hardware
reset when the link is up. This is generally relevant only if the SoC
provides the clock to an external PHY and the PHY is configured for RMII.
Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the various netif_level() helpers to simplify the C code. This was
suggested by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1611642024-3166-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a non nat tuple entry is inserted just to the regular tuples
rhashtable (ct_tuples_ht) and not to natted tuples rhashtable
(ct_nat_tuples_ht). Commit bc562be9674b ("net/mlx5e: CT: Save ct entries
tuples in hashtables") mixed up the return labels and names sot that on
cleanup or failure we still try to remove for the natted tuples rhashtable.
Fix that by correctly checking if a natted tuples insertion
before removing it. While here make it more readable.
Fixes: bc562be9674b ("net/mlx5e: CT: Save ct entries tuples in hashtables")
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
without reset
Sometimes, channel params are changed without recreating the channels.
It happens in two basic cases: when the channels are closed, and when
the parameter being changed doesn't affect how channels are configured.
Such changes invoke a hardware command that might fail. The whole
operation should be reverted in such cases, but the code that restores
the parameters' values in the driver was missing. This commit adds this
handling.
Fixes: 2e20a151205b ("net/mlx5e: Fail safe mtu and lro setting")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Trust state may be changed without recreating the channels. It happens
when the channels are closed, and when channel parameters (min inline
mode) stay the same after changing the trust state. Changing the trust
state is a hardware command that may fail. The current code didn't
restore the channel parameters to their old values if an error happened
and the channels were closed. This commit adds handling for this case.
Fixes: 6e0504c69811 ("net/mlx5e: Change inline mode correctly when changing trust state")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
is down
This commit addresses two issues related to changing the number of
queues when the channels are closed:
1. Missing call to mlx5e_num_channels_changed to update
real_num_tx_queues when the number of TCs is changed.
2. When mlx5e_num_channels_changed returns an error, the channel
parameters must be reverted.
Two Fixes: tags correspond to the first commits where these two issues
were introduced.
Fixes: 3909a12e7913 ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases")
Fixes: fa3748775b92 ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, if a neighbour isn't valid when offloading tunnel encap rules,
we offload the original match and replace the original action with
"goto slow path" action. For this we use a temporary flow attribute based
on the original flow attribute and then change the action. Flow flags,
which among those is the CT flag, are still shared for the slow path rule
offload, so we end up parsing this flow as a CT + goto slow path rule.
Besides being unnecessary, CT action offload saves extra information in
the passed flow attribute, such as created ct_flow and mod_hdr, which
is lost onces the temporary flow attribute is freed.
When a neigh is updated and is valid, we offload the original CT rule
with original CT action, which again creates a ct_flow and mod_hdr
and saves it in the flow's original attribute. Then we delete the slow
path rule with a temporary flow attribute based on original updated
flow attribute, and we free the relevant ct_flow and mod_hdr.
Then when tc deletes this flow, we try to free the ct_flow and mod_hdr
on the flow's attribute again.
To fix the issue, skip all furture proccesing (CT/Sample/Split rules)
in offload/unoffload of slow path rules.
Call trace:
[ 758.850525] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000218
[ 758.952987] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 758.964170] Modules linked in: act_csum(E) act_pedit(E) act_tunnel_key(E) act_ct(E) nf_flow_table(E) xt_nat(E) ip6table_filter(E) ip6table_nat(E) xt_comment(E) ip6_tables(E) xt_conntrack(E) xt_MASQUERADE(E) nf_conntrack_netlink(E) xt_addrtype(E) iptable_filter(E) iptable_nat(E) bpfilter(E) br_netfilter(E) bridge(E) stp(E) llc(E) xfrm_user(E) overlay(E) act_mirred(E) act_skbedit(E) rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) esp6_offload(E) esp6(E) esp4_offload(E) esp4(E) xfrm_algo(E) mlx5_ib(OE) ib_uverbs(OE) geneve(E) ip6_udp_tunnel(E) udp_tunnel(E) nfnetlink_cttimeout(E) nfnetlink(E) mlx5_core(OE) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_conncount(E) nf_nat(E) mlxfw(OE) psample(E) nf_conntrack(E) nf_defrag_ipv4(E) vfio_mdev(E) mdev(E) ib_core(OE) mlx_compat(OE) crct10dif_ce(E) uio_pdrv_genirq(E) uio(E) i2c_mlx(E) mlxbf_pmc(E) sbsa_gwdt(E) mlxbf_gige(E) gpio_mlxbf2(E) mlxbf_pka(E) mlx_trio(E) mlx_bootctl(E) bluefield_edac(E) knem(O)
[ 758.964225] ip_tables(E) mlxbf_tmfifo(E) ipv6(E) crc_ccitt(E) nf_defrag_ipv6(E)
[ 759.154186] CPU: 5 PID: 122 Comm: kworker/u16:1 Tainted: G OE 5.4.60-mlnx.52.gde81e85 #1
[ 759.172870] Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.5.0-2-gc1b5d64 Jan 4 2021
[ 759.195466] Workqueue: mlx5e mlx5e_rep_neigh_update [mlx5_core]
[ 759.207344] pstate: a0000005 (NzCv daif -PAN -UAO)
[ 759.217003] pc : mlx5_del_flow_rules+0x5c/0x160 [mlx5_core]
[ 759.228229] lr : mlx5_del_flow_rules+0x34/0x160 [mlx5_core]
[ 759.405858] Call trace:
[ 759.410804] mlx5_del_flow_rules+0x5c/0x160 [mlx5_core]
[ 759.421337] __mlx5_eswitch_del_rule.isra.43+0x5c/0x1c8 [mlx5_core]
[ 759.433963] mlx5_eswitch_del_offloaded_rule_ct+0x34/0x40 [mlx5_core]
[ 759.446942] mlx5_tc_rule_delete_ct+0x68/0x74 [mlx5_core]
[ 759.457821] mlx5_tc_ct_delete_flow+0x160/0x21c [mlx5_core]
[ 759.469051] mlx5e_tc_unoffload_fdb_rules+0x158/0x168 [mlx5_core]
[ 759.481325] mlx5e_tc_encap_flows_del+0x140/0x26c [mlx5_core]
[ 759.492901] mlx5e_rep_update_flows+0x11c/0x1ec [mlx5_core]
[ 759.504127] mlx5e_rep_neigh_update+0x160/0x200 [mlx5_core]
[ 759.515314] process_one_work+0x178/0x400
[ 759.523350] worker_thread+0x58/0x3e8
[ 759.530685] kthread+0x100/0x12c
[ 759.537152] ret_from_fork+0x10/0x18
[ 759.544320] Code: 97ffef55 51000673 3100067f 54ffff41 (b9421ab3)
[ 759.556548] ---[ end trace fab818bb1085832d ]---
Fixes: 4c3844d9e97e ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit introduce new CONFIG_MLX5_CLS_ACT kconfig variable
to control compilation of TC hardware offloads implementation.
When this configuration is disabled the driver is still wrongly
reports in ethtool that hw-tc-offload is supported.
Fixed by reporting hw-tc-offload is supported only when
CONFIG_MLX5_CLS_ACT is enabled.
Fixes: d956873f908c ("net/mlx5e: Introduce kconfig var for TC support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Pages for the host PF and ECPF were stored in the same tree, so the ECPF
pages were being freed along with the host PF's when the host driver
unloaded.
Combine the function ID and ECPF flag to use as an index into the
x-array containing the trees to get a different tree for the host PF and
ECPF.
Fixes: c6168161f693 ("net/mlx5: Add support for release all pages event")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When IPSEC offload isn't active, the number of stats is not zero, but
the strings are not filled, leading to exposing stats with empty names.
Fix this by using the same condition for NUM_STATS and FILL_STRS.
Fixes: 0aab3e1b04ae ("net/mlx5e: IPSec, Expose IPsec HW stat only for supporting HW")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
"Unsupported key used:" appears in kernel log when flows with
unsupported key are used, arp fields for example.
OpenVSwitch was changed to match on arp fields by default that
caused this warning to appear in kernel log for every arp rule, which
can be a lot.
Fix by lowering print level from warning to debug.
Fixes: e3a2b7ed018e ("net/mlx5e: Support offload cls_flower with drop action")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Instead of directly return, goto the error handling label to free
allocated page.
Fixes: 5f29458b77d5 ("net/mlx5e: Support dump callback in TX reporter")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.
Fix it by performing 64-bit calculation.
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When we create the ft object we also init rhltable in ft->fgs_hash.
So in error flow before kfree of ft we need to destroy that rhltable.
Fixes: 693c6883bbc4 ("net/mlx5: Add hash table for flow groups in flow table")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Link speed advertising in igc has two problems:
- When setting the advertisement via ethtool, the link speed is converted
to the legacy 32 bit representation for the intel PHY code.
This inadvertently drops ETHTOOL_LINK_MODE_2500baseT_Full_BIT (being
beyond bit 31). As a result, any call to `ethtool -s ...' drops the
2500Mbit/s link speed from the PHY settings. Only reloading the driver
alleviates that problem.
Fix this by converting the ETHTOOL_LINK_MODE_2500baseT_Full_BIT to the
Intel PHY ADVERTISE_2500_FULL bit explicitly.
- Rather than checking the actual PHY setting, the .get_link_ksettings
function always fills link_modes.advertising with all link speeds
the device is capable of.
Fix this by checking the PHY autoneg_advertised settings and report
only the actually advertised speeds up to ethtool.
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This change simplifies the VF initialization check and also minimizes
the delay between acquiring the VSI pointer and using it. As known by
the commit being fixed, there is a risk of the VSI pointer getting
changed. Therefore minimize the delay between getting and using the
pointer.
Fixes: 9889707b06ac ("i40e: Fix crash caused by stress setting of VF MAC addresses")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f90 ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747fde ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16be ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f573 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6adab ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the more modern API to get the match data out of the of match table.
This saves some code, lines, and nicely avoids referencing the match
table when it is undefined with configurations where CONFIG_OF=n.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-omap@vger.kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210123034428.2841052-3-swboyd@chromium.org
|
|
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Once the firmware fatal condition is detected, we should cease
comminication with the firmware and hardware quickly even if there
are many completion entries in the completion rings. This will
speed up the recovery process and prevent further I/Os that may
cause further exceptions.
Do not proceed in the NAPI poll function if fatal condition is
detected. Call napi_complete() and return without arming interrupts.
Cleanup of all rings and reset are imminent.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Combine the three netdev_warn() calls into a single call, printed at
the NETIF_MSG_HW log level.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the event of a fatal firmware error, firmware will notify the host
and then it will proceed to do core reset when it sees that all functions
have disabled Bus Master. To prevent Master Aborts and other hard
errors, we need to quiesce all activities in addition to disabling Bus
Master before the chip goes into core reset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the event of a fatal firmware error, we want to disable IRQ early
in the recovery sequence. This change will allow it to be called
safely again as part of the normal shutdown sequence.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Up until now, we don't need to keep track of this state because NAPI
is always enabled once and disabled once during bring up and shutdown.
For better error recovery in subsequent patches, we want to quiesce
the device earlier during fatal error conditions. The normal shutdown
sequence will disable NAPI again and the flag will prevent disabling
NAPI twice.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This code to check if we have reached the maximum wait time after
firmware reset is used multiple times. Add a helper function to
do this.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware may be in the middle of reset when the driver tries to do ifup.
In that case, firmware will return a special error code and the driver
will retry 10 times with 50 msecs delay after each retry.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drawing a hard line on aborted resets prevents a NIC open in
some scenarios that may otherwise be recoverable. For example,
if a firmware recovery happened while a PF was down and an
attempt was made to bring up an associated VF in this state,
then it was impossible to ever bring up this VF without a
rebind or reload of its driver.
Attempt to reinitialize the firmware when an aborted reset (or
failed init after a reset) is discovered during open - it may
succeed. Also take care to allow the user to retry opening the
NIC even after an aborted reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The timeout period for firmware messages is passed to the driver
from the firmware in the response of the first command. This
timeout period is multiplied by a factor for certain long
running commands such as NVRAM commands. In some cases, the
timeout period can become really long and it can cause hung task
warnings if firmware has crashed or is not responding. To avoid
such long delays, cap all firmware commands to a max timeout value
of 40 seconds.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If firmware is in reset or in bad state, it won't be able to return
VPD data. Move bnxt_vpd_read_info() until after bnxt_fw_init_one_p1()
successfully returns. By then we would have established proper
communications with the firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The first HWRM_VER_GET message to firmware during probe may timeout if
firmware is under reset. This can happen during hot-plug for example.
On P5 and newer chips, we can check if firmware is in the boot stage by
reading a status register. Retry 5 times if the status register shows
that firmware is not ready and not in error state.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing support for handling NO_MASTER crashes while ports are
administratively down (ifdown). On some SoC platforms, the driver
needs to assist the firmware to recover from a crash via OP-TEE.
This is performed in a similar fashion to what is done during driver
probe.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define macros to check for the various states in the lower 16 bits of
the health register. Replace the C code that checks for these values
with the newly defined macros.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Updates to backing store APIs, QoS profiles, and push buffer initial
index support.
Since the new HWRM_FUNC_BACKING_STORE_CFG message size has increased,
we need to add some compat. logic to fall back to the smaller legacy
size if firmware cannot accept the larger message size. The new fields
added to the structure are not used yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MT762x HW, except for MT7628, supports frame length up to 2048
(maximum length on GDM), so allow setting MTU up to 2030.
Also set the default frame length to the hardware default 1518.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210125042046.5599-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support SPI and sequence number fields of
ESP/AH header to be hashed for RSS. By default
ESP/AH fields are not considered for RSS and
needs to be set explicitly as below:
ethtool -U eth0 rx-flow-hash esp4 sdfn
or
ethtool -U eth0 rx-flow-hash ah4 sdfn
or
ethtool -U eth0 rx-flow-hash esp6 sdfn
or
ethtool -U eth0 rx-flow-hash ah6 sdfn
To disable hashing of ESP fields:
ethtool -U eth0 rx-flow-hash esp4 sd
or
ethtool -U eth0 rx-flow-hash ah4 sd
or
ethtool -U eth0 rx-flow-hash esp6 sd
or
ethtool -U eth0 rx-flow-hash ah6 sd
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/1611378552-13288-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When working on the PCI VPD code I also tested with a Broadcom BCM95719
card. tg3 uses internal NVRAM access with this card, so I forced it to
PCI VPD mode for testing. PCI VPD access fails
(i + PCI_VPD_LRDT_TAG_SIZE + j > len) because only TG3_NVM_VPD_LEN (256)
bytes are read, but PCI VPD has 400 bytes on this card.
So add a constant TG3_NVM_PCI_VPD_MAX_LEN that defines the maximum
PCI VPD size. The actual VPD size is returned by pci_read_vpd().
In addition it's not worth looping over pci_read_vpd(). If we miss the
125ms timeout per VPD dword read then definitely something is wrong,
and if the tg3 module loading is killed then there's also not much
benefit in retrying the VPD read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/cb9e9113-0861-3904-87e0-d4c4ab3c8860@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mvpp2 is an Ethernet driver, and it implements MAC style time
stamping of PTP frames. It has no need of the expensive option to
enable PHY time stamping. Remove the incorrect dependency.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dst entry should be released if no neighbour is found. Goto label
free_dst to fix the issue. Besides, the check of ndev against NULL is
redundant.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121145738.51091-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
