| Age | Commit message (Collapse) | Author |
|---|
|
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: 1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes: cc2295cd54e4 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers")
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88f5 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390bb ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No need to have the used_list - we don't need to keep track of the
used chunks, we only need to know the amount of used memory.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When ICM chunk is freed, it might still be accessed by HW until we do
sync with HW. This sync is expensive operation, so we don't do it often.
Instead, when the chunk is freed, it is moved to the buddy's "hot memory"
list. Once sync is done, we traverse the hot list and finally free all
the chunks.
It appears that traversing a long list takes unusually long time due to cache
misses on many entries, which causes a big "hiccup" during rule insertion.
This patch deals with this issue the following way:
- Move hot chunks list from buddy to pool, so that the pool will
keep track of all its hot memory.
- Replace the list with pre-allocated array on the memory pool struct,
and store only the information that is needed to later free this
chunk in its buddy allocator.
This cost additional memory for the array that is dynamically
allocated, but it allows not to save long list of hot chunks,
so at peak times it actually saves memory due to the fact that
each array entry is much smaller than the chunk struct.
This way an overhead of traversing the long list is virtually removed:
the loop of freeing hot chunks takes ~27 msec instead of ~70 msec, where
most of it are the actual freeing activities.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Instead of hiding the math in the code, define a value that sets the
fraction of allowed hot memory of ICM pool.
Set the threshold for sync of ICM hot chunks to 1/4 of the pool
instead of 1/2 of the pool. Although we will have more syncs, each
sync will be shorter and will help with insertion rate stability.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
SW steering allocates/frees lots of htbl structs. Create a
separate kmem_cache and allocate htbls from this allocator.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
SW steering allocates/frees lots of icm_chunk structs. To make this more
efficiently, create a separate kmem_cache and allocate these chunks from
this allocator.
By doing this we observe that the alloc/free "hiccups" frequency has
become much lower, which allows for a more steady rule insersion rate.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Instead of allocating/freeing send info objects dynamically, manage them
in pool. The number of send info objects doesn't depend on rules, so after
pre-populating the pool with an initial batch of send info objects, the
pool is not expected to grow.
This way we save alloc/free during writing STEs to ICM, which can
sometimes take up to 40msec.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Don't wait for the whole table to be ready - write each row immediately.
This way we save allocations of the ste_send_info structure and improve
performance.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Handle creation/destruction of all the domain's memory pools and other
memory-related fields in a separate init/uninit functions.
This simplifies error flow and allows cleaner addition of new pools.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Rather than cleaning the corresponding chunk's section of ste_arrays on
chunk deletion, initialize these areas upon chunk creation.
Chunk destruction tend to come in large batches (during pool syncing).
To reduce the "hiccup" in such cases, moving ste_arrays init from chunk
destruction to initialization.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
While creating rule, ste_arr is an array that is allocated at the start
of the function and freed at the end.
This memory allocation can sometimes lead to "hiccups" of up to 10ms.
However, the common use case is short chains of STEs. For such cases,
we can use a local buffer on stack instead.
Changes in v2:
Use small local array for short rules, allocate dynamically for long rules
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Remove an argument that can be extracted in the function.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Calling fast teardown as part of the normal unloading caused
a problem with SW steering - SW steering still needs to clear
its tables, write to ICM and poll for completions.
When teardown has been done, SW steering keeps polling the CQ
forever, because nobody flushes it.
This patch fixes the issue by checking the device state in
cases where no CQE was returned.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
If sync happens when the device is in fast teardown, just bail
and don't do anything, because the PCI device is not there any more.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Otherwise resources will never be freed and refcount will not be decreased.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The git history for this driver seems to be completely
automated / tree wide changes. I can't find any boards
or systems which would use this chip. Google search
shows pictures of towel warmers and no networking products.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221025184254.1717982-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add new VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC flag, opcode
VIRTCHNL_OP_GET_SUPPORTED_RXDIDS and add member rxdid
in struct virtchnl_rxq_info to support AVF Flex RXD
extension.
Add support to allow VF to query flexible descriptor RXDIDs supported
by DDP package and configure Rx queues with selected RXDID for IAVF.
Add code to allow VIRTCHNL_OP_GET_SUPPORTED_RXDIDS message to be
processed. Add necessary macros for registers.
Signed-off-by: Leyi Rong <leyi.rong@intel.com>
Signed-off-by: Xu Ting <ting.xu@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221025161252.1952939-1-jacob.e.keller@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RX code can be more efficient with the build_skb(). Allocating actual
SKB around eth packet buffer - right before passing it up - results in
a better cache usage.
Without RPS (echo 0 > rps_cpus) BCM4908 NAT masq performance "jumps"
between two speeds: ~900 Mbps and 940 Mbps (it's a 4 CPUs SoC). This
change bumps the lower speed from 905 Mb/s to 918 Mb/s (tested using
single stream iperf 2.0.5 traffic).
There are more optimizations to consider. One obvious to try is GRO
however as BCM4908 doesn't do hw csum is may actually lower performance.
Sometimes. Some early testing:
┌─────────────────────────────────┬─────────────────────┬────────────────────┐
│ │ netif_receive_skb() │ napi_gro_receive() │
├─────────────────────────────────┼─────────────────────┼────────────────────┤
│ netdev_alloc_skb() │ 905 Mb/s │ 892 Mb/s │
│ napi_alloc_frag() + build_skb() │ 918 Mb/s │ 917 Mb/s │
└─────────────────────────────────┴─────────────────────┴────────────────────┘
Another ideas:
1. napi_build_skb()
2. skb_copy_from_linear_data() for small packets
Those need proper testing first though. That can be done later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20221025132245.22871-1-zajec5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes: 1acf2318dd13 ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It doesn't need extra macros for queue 0 & 4. Same macro could
be used for all 8 queues. Related queue/channel functions could
be combined together.
Original macro which has two same parameters is unsafe macro and
might have potential side effects. Each MTL RxQ DMA channel mask
is 4 bits, so using (0xf << chan) instead of GENMASK(x + 3, x) to
avoid unsafe macro.
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Link: https://lore.kernel.org/r/20221025081747.1884926-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ave_open() in ave_resume() executes __phy_resume() via phy_start(), so no
need to call phy_resume() explicitly. Remove it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072314.24969-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Variable tx_use is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024143501.2163720-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes: 8ca86fd83eae ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Variable num_entries is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221024125951.2155434-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set max_mtu/min_mtu directly to avoid making the validity judgment
when set mtu, because the judgment is made in net/core: dev_validate_mtu,
so to simplify the code.
Signed-off-by: caihuoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20221024103349.4494-1-cai.huoqing@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 3ba9bcb4b68f ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add pause get and set functions
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Round up allocations with kmalloc_size_roundup() so that build_skb()'s
use of ksize() is always accurate and no special handling of the memory
is needed by KASAN, UBSAN_BOUNDS, nor FORTIFY_SOURCE.
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022021004.gonna.489-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RK3588(s) can have multiple gmac controllers.
Re-use rk3568 logic to distinguish them.
Fixes: 2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
action skbedit queue_mapping 5 skip_sw
The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.
Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a frame is sent using FDMA, the skb is mapped and then the mapped
address is given to an tx dcb that is different than the last used tx
dcb. Once the HW finish with this frame, it would generate an interrupt
and then the dcb can be reused and memory can be freed. For each dcb
there is an dcb buf that contains some meta-data(is used by PTP, is
it free). There is 1 to 1 relationship between dcb and dcb_buf.
The following issue was observed. That sometimes after changing the MTU
to allocate new tx dcbs and dcbs_buf, two frames were not
transmitted. The frames were not transmitted because when reloading the
tx dcbs, it was always presuming to use the first dcb but that was not
always happening. Because it could be that the last tx dcb used before
changing MTU was first dcb and then when it tried to get the next dcb it
would take dcb 1 instead of 0. Because it is supposed to take a
different dcb than the last used one. This can be fixed simply by
changing tx->last_in_use to -1 when the fdma is disabled to reload the
new dcb and dcbs_buff.
But there could be a different issue. For example, right after the frame
is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be
cleared. And now get the interrupt from HW that it finished with the
frame. So when we try to clear the skb, it is not possible because we
lost all the dcbs_buf.
The solution here is to stop replacing the tx dcbs and dcbs_buf when
changing MTU because the TX doesn't care what is the MTU size, it is
only the RX that needs this information.
Fixes: 2ea1cbac267e ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221021090711.3749009-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Resize of the UPDATE entry is required if the image to
be flashed is larger than the available space. Add this step,
otherwise flashing larger firmware images by ethtool or devlink
may fail.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for .get_module_eeprom_by_page() callback which
implements generic solution for module`s eeprom access.
v3: Add bnxt_get_module_status() to get a more specific extack error
string.
Return -EINVAL from bnxt_get_module_eeprom_by_page() when we
don't want to fallback to old method.
v2: Simplification suggested by Ido Schimmel
Link: https://lore.kernel.org/netdev/YzVJ%2FvKJugoz15yV@shredder/
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The main changes are PTM timestamp support, CMIS EEPROM support, and
asymmetric CoS queues support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
include/linux/net.h
a5ef058dc4d9 ("net: introduce and use custom sockopt socket flag")
e993ffe3da4b ("net: flag sockets supporting msghdr originated zerocopy")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fixes: 504d4721ee8e ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_stop_all_queues must be called before calling H_FREE_LOGICAL_LAN.
As a result, we can remove the pool_config field from the ibmveth
adapter structure.
Some device configuration changes call ibmveth_close in order to free
the current resources held by the device. These functions then make
their changes and call ibmveth_open to reallocate and reserve resources
for the device.
Prior to this commit, the flag pool_config was used to tell ibmveth_close
that it should not halt the transmit queue. pool_config was introduced in
commit 860f242eb534 ("[PATCH] ibmveth change buffer pools dynamically")
to avoid interrupting the tx flow when making rx config changes. Since
then, other commits adopted this approach, even if making tx config
changes.
The issue with this approach was that the hypervisor freed all of
the devices control structures after the hcall H_FREE_LOGICAL_LAN
was performed but the transmit queues were never stopped. So the higher
layers in the network stack would continue transmission but any
H_SEND_LOGICAL_LAN hcall would fail with H_PARAMETER until the
hypervisor's structures for the device were allocated with the
H_REGISTER_LOGICAL_LAN hcall in ibmveth_open. This resulted in
no real networking harm but did cause several of these error
messages to be logged: "h_send_logical_lan failed with rc=-4"
So, instead of trying to keep the transmit queues alive during network
configuration changes, just stop the queues, make necessary changes then
restart the queues.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for configuring periodic output
signal of PPS. So the PPS can be output at a specified time
and period.
For developers or testers, they can use the command "echo
<channel> <start.sec> <start.nsec> <period.sec> <period.
nsec> > /sys/class/ptp/ptp0/period" to specify time and
period to output PPS signal.
Notice that, the channel can only be set to 0. In addtion,
the start time must larger than the current PTP clock time.
So users can use the command "phc_ctl /dev/ptp0 -- get" to
get the current PTP clock time before.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before 262f2b782e25 ("net: fman: Map the base address once"), the
physical address of the MAC was exposed to userspace in two places: via
sysfs and via SIOCGIFMAP. While this is not best practice, it is an
external ABI which is in use by userspace software.
The aforementioned commit inadvertently modified these addresses and
made them virtual. This constitutes and ABI break. Additionally, it
leaks the kernel's memory layout to userspace. Partially revert that
commit, reintroducing the resource back into struct mac_device, while
keeping the intended changes (the rework of the address mapping).
Fixes: 262f2b782e25 ("net: fman: Map the base address once")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for 800Gbps speed, link modes of 100Gbps per lane.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
