Age | Commit message (Collapse) | Author |
|
During driver initialization disable stale DMAC filters
in CGX/RPM set by firmware.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250720163638.1560323-3-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Octeontx2/CN10k MAC block supports DMAC filters. DMAC filters
can be installed on the interface through ethtool.
When a user installs a DMAC filter, the interface's MAC address
is implicitly added to the filter list. To ensure consistency,
this MAC address must be kept in sync with the pfvf->mac_addr field,
which is used to install MAC-based NPC rules.
This patch updates the pfvf->mac_addr field with the programmed MAC
address and also enables VF interfaces to install DMAC filters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250720163638.1560323-2-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch enables batched RX buffer replenishment in ibmveth by
using the new firmware-supported h_add_logical_lan_buffers() hcall
to submit up to 8 RX buffers in a single call, instead of repeatedly
calling the single-buffer h_add_logical_lan_buffer() hcall.
During the probe, with the patch, the driver queries ILLAN attributes
to detect IBMVETH_ILLAN_RX_MULTI_BUFF_SUPPORT bit. If the attribute is
present, rx_buffers_per_hcall is set to 8, enabling batched replenishment.
Otherwise, it defaults to 1, preserving the original upstream behavior
with no change in code flow for unsupported systems.
The core rx replenish logic remains the same. But when batching
is enabled, the driver aggregates up to 8 fully prepared descriptors
into a single h_add_logical_lan_buffers() hypercall. If any allocation
or DMA mapping fails while preparing a batch, only the successfully
prepared buffers are submitted, and the remaining are deferred for
the next replenish cycle.
If at runtime the firmware stops accepting the batched hcall—e,g,
after a Live Partition Migration (LPM) to a host that does not
support h_add_logical_lan_buffers(), the hypercall returns H_FUNCTION.
In that case, the driver transparently disables batching, resets
rx_buffers_per_hcall to 1, and falls back to the single-buffer hcall
in next future replenishments to take care of these and future buffers.
Test were done on systems with firmware that both supports and
does not support the new h_add_logical_lan_buffers hcall.
On supported firmware, this reduces hypercall overhead significantly
over multiple buffers. SAR measurements showed about a 15% improvement
in packet processing rate under moderate RX load, with heavier traffic
seeing gains more than 30%
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250719091356.57252-1-mmc@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the RX datapath for AF_XDP zero-copy for DQ RDA. The RX path is
quite similar to that of the normal XDP case. Parallel methods are
introduced to properly handle XSKs instead of normal driver buffers.
To properly support posting from XSKs, queues are destroyed and
recreated, as the driver was initially making use of page pool buffers
instead of the XSK pool memory.
Expose support for AF_XDP zero-copy, as the TX and RX datapaths both
exist.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-6-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the descriptor clean path, a number of changes need to be made to
accommodate out of order completions and double completions.
The XSK stack can only handle completions being processed in order, as a
single counter is incremented in xsk_tx_completed to sigify how many XSK
descriptors have been completed. Because completions can come back out
of order in DQ, a separate queue of XSK descriptors must be maintained.
This queue keeps the pending packets in the order that they were written
so that the descriptors can be counted in xsk_tx_completed in the same
order.
For double completions, a new pending packet state and type are
introduced. The new type, GVE_TX_PENDING_PACKET_DQO_XSK, plays an
anlogous role to pre-existing _SKB and _XDP_FRAME pending packet types
for XSK descriptors. The new state, GVE_PACKET_STATE_XSK_COMPLETE,
represents packets for which no more completions are expected. This
includes packets which have received a packet completion or reinjection
completion, as well as packets whose reinjection completion timer have
timed out. At this point, such packets can be counted as part of
xsk_tx_completed() and freed.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-5-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Relying on xsk_get_pool_from_qid for getting whether zero copy is
enabled on a queue is erroneous, as an XSK pool is registered in
xp_assign_dev whether AF_XDP zero-copy is enabled or not. This becomes
problematic when queues are restarted in copy mode, as all RX queues
with XSKs will register a pool, causing the driver to exercise the
zero-copy codepath.
This patch adds a bitmap to keep track of which queues have zero-copy
enabled.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-4-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The existence of both of these xdp_rxq and xsk_rxq is redundant. xdp_rxq
can be used in both the zero-copy mode and the copy mode case. XSK pool
memory model registration is prioritized over normal memory model
registration to ensure that memory model registration happens only once
per queue.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-3-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The XDP registration path currently has a lot of reused logic, leading
changes to the codepaths to be unnecessarily complex. gve_reg_xsk_pool
extracts the logic of registering an XSK pool with a queue into a method
that can be used by both XDP_SETUP_XSK_POOL and gve_reg_xdp_info.
gve_unreg_xdp_info is used to undo XDP info registration in the error
path instead of explicitly unregistering the XDP info, as it is more
complete and idempotent.
This patch will be followed by other changes to the XDP registration
logic, and will simplify those changes due to the use of common methods.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://patch.msgid.link/20250717152839.973004-2-jeroendb@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-07-18 (idpf, ice, igc, igbvf, ixgbevf)
For idpf:
Ahmed and Sudheer add support for flow steering via ntuple filters.
Current support is for IPv4 and TCP/UDP only.
Milena adds support for cross timestamping.
Ahmed preserves coalesce settings across resets.
For ice:
Alex adds reporting of 40GbE speed in devlink port split.
Dawid adds support for E835 devices.
Jesse refactors profile ptype processing for cleaner, more readable,
code.
Dave adds a couple of helper functions for LAG to reduce code
duplication.
For igc:
Siang adds support to configure "Default Queue" during runtime using
ethtool's Network Flow Classification (NFC) wildcard rule approach.
For igbvf:
Yuto Ohnuki removes unused fields from igbvf_adapter.
For ixgbevf:
Yuto Ohnuki removes unused fields from ixgbevf_adapter.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbevf: remove unused fields from struct ixgbevf_adapter
igbvf: remove unused fields from struct igbvf_adapter
igc: Add wildcard rule support to ethtool NFC using Default Queue
igc: Relocate RSS field definitions to igc_defines.h
ice: breakout common LAG code into helpers
ice: convert ice_add_prof() to bitmap
ice: add E835 device IDs
ice: add 40G speed to Admin Command GET PORT OPTION
idpf: preserve coalescing settings across resets
idpf: add cross timestamping
idpf: add flow steering support
virtchnl2: add flow steering support
virtchnl2: rename enum virtchnl2_cap_rss
====================
Link: https://patch.msgid.link/20250718185118.2042772-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gve_tx_timeout was calculating missed completions in a way that is only
relevant in the GQ queue format. Additionally, it was attempting to
disable device interrupts, which is not needed in either GQ or DQ queue
formats.
As a result, TX timeouts with the DQ queue format likely would have
triggered early resets without kicking the queue at all.
This patch drops the check for pending work altogether and always kicks
the queue after validating the queue has not seen a TX timeout too
recently.
Cc: stable@vger.kernel.org
Fixes: 87a7f321bb6a ("gve: Recover from queue stall due to missed IRQ")
Co-developed-by: Tim Hostetler <thostet@google.com>
Signed-off-by: Tim Hostetler <thostet@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250717192024.1820931-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PM suspend/resume callbacks for RZ/G3E SMARC EVK.
The PM deep entry is executed by pressing the SLEEP button and exit from
entry is by pressing the power button.
Logs:
root@smarc-rzg3e:~# PM: suspend entry (deep)
Filesystems sync: 0.115 seconds
Freezing user space processes
Freezing user space processes completed (elapsed 0.002 seconds)
OOM killer disabled.
Freezing remaining freezable tasks
Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
printk: Suspending console(s) (use no_console_suspend to debug)
NOTICE: BL2: v2.10.5(release):2.10.5/rz_soc_dev-162-g7148ba838
NOTICE: BL2: Built : 14:23:58, Jul 5 2025
NOTICE: BL2: SYS_LSI_MODE: 0x13e06
NOTICE: BL2: SYS_LSI_DEVID: 0x8679447
NOTICE: BL2: SYS_LSI_PRR: 0x0
NOTICE: BL2: Booting BL31
renesas-gbeth 15c30000.ethernet end0: Link is Down
Disabling non-boot CPUs ...
psci: CPU3 killed (polled 0 ms)
psci: CPU2 killed (polled 0 ms)
psci: CPU1 killed (polled 0 ms)
Enabling non-boot CPUs ...
Detected VIPT I-cache on CPU1
GICv3: CPU1: found redistributor 100 region 0:0x0000000014960000
CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
CPU1 is up
Detected VIPT I-cache on CPU2
GICv3: CPU2: found redistributor 200 region 0:0x0000000014980000
CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
CPU2 is up
Detected VIPT I-cache on CPU3
GICv3: CPU3: found redistributor 300 region 0:0x00000000149a0000
CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
CPU3 is up
dwmac4: Master AXI performs fixed burst length
15c30000.ethernet end0: No Safety Features support found
15c30000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported
15c30000.ethernet end0: configuring for phy/rgmii-id link mode
dwmac4: Master AXI performs fixed burst length
15c40000.ethernet end1: No Safety Features support found
15c40000.ethernet end1: IEEE 1588-2008 Advanced Timestamp supported
15c40000.ethernet end1: configuring for phy/rgmii-id link mode
OOM killer enabled.
Restarting tasks: Starting
Restarting tasks: Done
random: crng reseeded on system resumption
PM: suspend exit
15c30000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx
root@smarc-rzg3e:~# ifconfig end0 192.168.10.7 up
root@smarc-rzg3e:~# ping 192.168.10.1
PING 192.168.10.1 (192.168.10.1) 56(84) bytes of data.
64 bytes from 192.168.10.1: icmp_seq=1 ttl=64 time=2.05 ms
64 bytes from 192.168.10.1: icmp_seq=2 ttl=64 time=0.928 ms
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20250717071109.8213-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On ASP versions v2.x we need to program the TX map vector register to
properly exercise end-to-end flow control, otherwise the TX engine can
either lock-up, or cause the hardware calculated checksum to be
wrong/corrupted when multiple back to back packets are being submitted
for transmission. This register defaults to 0, which means no flow
control being applied.
Fixes: e9f31435ee7d ("net: bcmasp: Add support for asp-v3.0")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250718212242.3447751-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adds complete support for hardware-based PTP (IEEE 1588)
timestamping to the AMD XGBE driver.
- Initialize and configure the MAC PTP registers based on link
speed and reference clock.
- Support both 50MHz and 125MHz PTP reference clocks.
- Update the driver interface and version data to support PTP
clock frequency selection.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250718185628.4038779-3-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the hwptp abstraction and associated callbacks from
the struct xgbe_hw_if {}.
The callback structure was only ever assigned a single function, without
null checks. This cleanup inlines the logic and moves all the hwtstamp
realted code a separate file, improving readability and maintainance.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20250718185628.4038779-2-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described by Vitaly Lifshits:
> Starting from Tiger Lake, LAN NVM is locked for writes by SW, so the
> driver cannot perform checksum validation and correction. This means
> that all NVM images must leave the factory with correct checksum and
> checksum valid bit set.
Unfortunately some systems have left the factory with an uninitialized
value of 0xFFFF at register address 0x3F (checksum word location).
So on Tiger Lake platform we ignore the computed checksum when such
condition is encountered.
Signed-off-by: Jacek Kowalski <jacek@jacekk.info>
Tested-by: Vlad URSU <vlad@ursu.me>
Fixes: 4051f68318ca9 ("e1000e: Do not take care about recovery NVM checksum")
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
As described by Vitaly Lifshits:
> Starting from Tiger Lake, LAN NVM is locked for writes by SW, so the
> driver cannot perform checksum validation and correction. This means
> that all NVM images must leave the factory with correct checksum and
> checksum valid bit set. Since Tiger Lake devices were the first to have
> this lock, some systems in the field did not meet this requirement.
> Therefore, for these transitional devices we skip checksum update and
> verification, if the valid bit is not set.
Signed-off-by: Jacek Kowalski <jacek@jacekk.info>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Fixes: 4051f68318ca9 ("e1000e: Do not take care about recovery NVM checksum")
Cc: stable@vger.kernel.org
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add check for the return value of devm_kmemdup()
to prevent potential null pointer dereference.
Fixes: c76488109616 ("ice: Implement Dynamic Device Personalization (DDP) download")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the PF is processing an Admin Queue message to delete a VF's MACs
from the MAC filter, we currently check if the PF set the MAC and if
the VF is trusted.
This results in undesirable behaviour, where if a trusted VF with a
PF-set MAC sets itself down (which sends an AQ message to delete the
VF's MAC filters) then the VF MAC is erased from the interface.
This results in the VF losing its PF-set MAC which should not happen.
There is no need to check for trust at all, because an untrusted VF
cannot change its own MAC. The only check needed is whether the PF set
the MAC. If the PF set the MAC, then don't erase the MAC on link-down.
Resolve this by changing the deletion check only for PF-set MAC.
(the out-of-tree driver has also intentionally removed the check for VF
trust here with OOT driver version 2.26.8, this changes the Linux kernel
driver behaviour and comment to match the OOT driver behaviour)
Fixes: ea2a1cfc3b201 ("i40e: Fix VF MAC filter removal")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently the tx_dropped field in VF stats is not updated correctly
when reading stats from the PF. This is because it reads from
i40e_eth_stats.tx_discards which seems to be unused for per VSI stats,
as it is not updated by i40e_update_eth_stats() and the corresponding
register, GLV_TDPC, is not implemented[1].
Use i40e_eth_stats.tx_errors instead, which is actually updated by
i40e_update_eth_stats() by reading from GLV_TEPC.
To test, create a VF and try to send bad packets through it:
$ echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
$ cat test.py
from scapy.all import *
vlan_pkt = Ether(dst="ff:ff:ff:ff:ff:ff") / Dot1Q(vlan=999) / IP(dst="192.168.0.1") / ICMP()
ttl_pkt = IP(dst="8.8.8.8", ttl=0) / ICMP()
print("Send packet with bad VLAN tag")
sendp(vlan_pkt, iface="enp2s0f0v0")
print("Send packet with TTL=0")
sendp(ttl_pkt, iface="enp2s0f0v0")
$ ip -s link show dev enp2s0f0
16: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:e0:ac brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
0 0 0 0 0 0
vf 0 link/ether e2:c6:fd:c1:1e:92 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
RX: bytes packets mcast bcast dropped
0 0 0 0 0
TX: bytes packets dropped
0 0 0
$ python test.py
Send packet with bad VLAN tag
.
Sent 1 packets.
Send packet with TTL=0
.
Sent 1 packets.
$ ip -s link show dev enp2s0f0
16: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:e0:ac brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
0 0 0 0 0 0
vf 0 link/ether e2:c6:fd:c1:1e:92 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
RX: bytes packets mcast bcast dropped
0 0 0 0 0
TX: bytes packets dropped
0 0 0
A packet with non-existent VLAN tag and a packet with TTL = 0 are sent,
but tx_dropped is not incremented.
After patch:
$ ip -s link show dev enp2s0f0
19: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:e0:ac brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collsns
0 0 0 0 0 0
vf 0 link/ether 4a:b7:3d:37:f7:56 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
RX: bytes packets mcast bcast dropped
0 0 0 0 0
TX: bytes packets dropped
0 0 2
Fixes: dc645daef9af5bcbd9c ("i40e: implement VF stats NDO")
Signed-off-by: Dennis Chen <dechen@redhat.com>
Link: https://www.intel.com/content/www/us/en/content-details/596333/intel-ethernet-controller-x710-tm4-at2-carlsville-datasheet.html
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Select use CONFIG_SYSFB only if EFI is enabled (Michael Kelley)
- An assorted set of fixes to remove warnings for missing export.h
header inclusion (Naman Jain)
- An assorted set of fixes for when Linux run as the root partition
for Microsoft Hypervisor (Mukesh Rathor, Nuno Das Neves, Stanislav
Kinsburskii)
- Fix the check for HYPERVISOR_CALLBACK_VECTOR (Naman Jain)
- Fix fcopy tool to handle irregularities with size of ring buffer
(Naman Jain)
- Fix incorrect file path conversion in fcopy tool (Yasumasa Suenaga)
* tag 'hyperv-fixes-signed-20250718' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
tools/hv: fcopy: Fix irregularities with size of ring buffer
PCI: hv: Use the correct hypercall for unmasking interrupts on nested
x86/hyperv: Expose hv_map_msi_interrupt()
Drivers: hv: Use nested hypercall for post message and signal event
x86/hyperv: Clean up hv_map/unmap_interrupt() return values
x86/hyperv: Fix usage of cpu_online_mask to get valid cpu
PCI: hv: Don't load the driver for baremetal root partition
net: mana: Fix warnings for missing export.h header inclusion
PCI: hv: Fix warnings for missing export.h header inclusion
clocksource: hyper-v: Fix warnings for missing export.h header inclusion
x86/hyperv: Fix warnings for missing export.h header inclusion
Drivers: hv: Fix warnings for missing export.h header inclusion
Drivers: hv: Fix the check for HYPERVISOR_CALLBACK_VECTOR
tools/hv: fcopy: Fix incorrect file path conversion
Drivers: hv: Select CONFIG_SYSFB only if EFI is enabled
|
|
This adds the capabilities, ipsec_next_header and inner/outer
l4_type_ext fields to support RSS for the decrypted packets.
These fields are specifically for firmware steering. HWS validation
logic is updated to correctly handle the changes, ensuring the
unsupported fields are not set.
Besides, reserved_at_c4 is fixed to reserved_at_d4 to reflect the
accurate offset within the structure.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1752734895-257735-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
In the original design, it is assumed local and peer eswitches have the
same number of vfs. However, in new firmware, local and peer eswitches
can have different number of vfs configured by mlxconfig. In such
configuration, it is incorrect to derive the number of vfs from the
local device's eswitch.
Fix this by updating the peer miss rules add and delete functions to use
the peer device's eswitch and vf count instead of the local device's
information, ensuring correct behavior regardless of vf configuration
differences.
Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1752753970-261832-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If cmd_exec() is called with callback and mlx5_cmd_invoke() returns an
error, resources allocated in cmd_exec() will not be freed.
Fix the code to release the resources if mlx5_cmd_invoke() returns an
error.
Fixes: f086470122d5 ("net/mlx5: cmdif, Return value improvements")
Reported-by: Alex Tereshkin <atereshkin@nvidia.com>
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Vlad Dumitrescu <vdumitrescu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1752753970-261832-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The TCP header fields seq and ack_seq are 32-bit values in network
byte order as (__be32). these fields were earlier printed using
ntohs(), which converts only 16-bit values and produces incorrect
results for 32-bit fields. This patch is changeing the conversion
to ntohl(), ensuring correct interpretation of these sequence numbers.
Notably, the format specifier is updated from %d to %u to reflect the
unsigned nature of these fields.
improves the accuracy of debug log messages for TCP sequence and
acknowledgment numbers during TX timeouts.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717193552.3648791-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wire-up ethtool_ops::nway_reset to phy_ethtool_nway_reset in order to
support re-starting auto-negotiation.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250717180915.2611890-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
netif_close_many is used only by vlan/dsa and one mtk driver, so move it into
NETDEV_INTERNAL namespace.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-8-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Note that one dev_set_threaded call still remains in mt76 for debugfs file.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-7-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cc34acd577f1 ("docs: net: document new locking reality")
introduced netif_ vs dev_ function semantics: the former expects locked
netdev, the latter takes care of the locking. We don't strictly
follow this semantics on either side, but there are more dev_xxx handlers
now that don't fit. Rename them to netif_xxx where appropriate.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250717172333.1288349-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes overlapping buffer allocation for ICSSG peripheral
used for storing packets to be received/transmitted.
There are 3 buffers:
1. Buffer for Locally Injected Packets
2. Buffer for Forwarding Packets
3. Buffer for Host Egress Packets
In existing allocation buffers for 2. and 3. are overlapping causing
packet corruption.
Packet corruption observations:
During tcp iperf testing, due to overlapping buffers the received ack
packet overwrites the packet to be transmitted. So, we see packets on
wire with the ack packet content inside the content of next TCP packet
from sender device.
Details for AM64x switch mode:
-> Allocation by existing driver:
+---------+-------------------------------------------------------------+
| | SLICE 0 | SLICE 1 |
| +------+--------------+--------+------+--------------+--------+
| | Slot | Base Address | Size | Slot | Base Address | Size |
|---------+------+--------------+--------+------+--------------+--------+
| | 0 | 70000000 | 0x2000 | 0 | 70010000 | 0x2000 |
| | 1 | 70002000 | 0x2000 | 1 | 70012000 | 0x2000 |
| | 2 | 70004000 | 0x2000 | 2 | 70014000 | 0x2000 |
| FWD | 3 | 70006000 | 0x2000 | 3 | 70016000 | 0x2000 |
| Buffers | 4 | 70008000 | 0x2000 | 4 | 70018000 | 0x2000 |
| | 5 | 7000A000 | 0x2000 | 5 | 7001A000 | 0x2000 |
| | 6 | 7000C000 | 0x2000 | 6 | 7001C000 | 0x2000 |
| | 7 | 7000E000 | 0x2000 | 7 | 7001E000 | 0x2000 |
+---------+------+--------------+--------+------+--------------+--------+
| | 8 | 70020000 | 0x1000 | 8 | 70028000 | 0x1000 |
| | 9 | 70021000 | 0x1000 | 9 | 70029000 | 0x1000 |
| | 10 | 70022000 | 0x1000 | 10 | 7002A000 | 0x1000 |
| Our | 11 | 70023000 | 0x1000 | 11 | 7002B000 | 0x1000 |
| LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 |
| Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 |
| | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 |
| | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 |
+---------+------+--------------+--------+------+--------------+--------+
| | 16 | 70024000 | 0x1000 | 16 | 7002C000 | 0x1000 |
| | 17 | 70025000 | 0x1000 | 17 | 7002D000 | 0x1000 |
| | 18 | 70026000 | 0x1000 | 18 | 7002E000 | 0x1000 |
| Their | 19 | 70027000 | 0x1000 | 19 | 7002F000 | 0x1000 |
| LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 |
| Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 |
| | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 |
| | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 |
+---------+------+--------------+--------+------+--------------+--------+
--> here 16, 17, 18, 19 overlapping with below express buffer
+-----+-----------------------------------------------+
| | SLICE 0 | SLICE 1 |
| +------------+----------+------------+----------+
| | Start addr | End addr | Start addr | End addr |
+-----+------------+----------+------------+----------+
| EXP | 70024000 | 70028000 | 7002C000 | 70030000 | <-- Overlapping
| PRE | 70030000 | 70033800 | 70034000 | 70037800 |
+-----+------------+----------+------------+----------+
+---------------------+----------+----------+
| | SLICE 0 | SLICE 1 |
+---------------------+----------+----------+
| Default Drop Offset | 00000000 | 00000000 | <-- Field not configured
+---------------------+----------+----------+
-> Allocation this patch brings:
+---------+-------------------------------------------------------------+
| | SLICE 0 | SLICE 1 |
| +------+--------------+--------+------+--------------+--------+
| | Slot | Base Address | Size | Slot | Base Address | Size |
|---------+------+--------------+--------+------+--------------+--------+
| | 0 | 70000000 | 0x2000 | 0 | 70040000 | 0x2000 |
| | 1 | 70002000 | 0x2000 | 1 | 70042000 | 0x2000 |
| | 2 | 70004000 | 0x2000 | 2 | 70044000 | 0x2000 |
| FWD | 3 | 70006000 | 0x2000 | 3 | 70046000 | 0x2000 |
| Buffers | 4 | 70008000 | 0x2000 | 4 | 70048000 | 0x2000 |
| | 5 | 7000A000 | 0x2000 | 5 | 7004A000 | 0x2000 |
| | 6 | 7000C000 | 0x2000 | 6 | 7004C000 | 0x2000 |
| | 7 | 7000E000 | 0x2000 | 7 | 7004E000 | 0x2000 |
+---------+------+--------------+--------+------+--------------+--------+
| | 8 | 70010000 | 0x1000 | 8 | 70050000 | 0x1000 |
| | 9 | 70011000 | 0x1000 | 9 | 70051000 | 0x1000 |
| | 10 | 70012000 | 0x1000 | 10 | 70052000 | 0x1000 |
| Our | 11 | 70013000 | 0x1000 | 11 | 70053000 | 0x1000 |
| LI | 12 | 00000000 | 0x0 | 12 | 00000000 | 0x0 |
| Buffers | 13 | 00000000 | 0x0 | 13 | 00000000 | 0x0 |
| | 14 | 00000000 | 0x0 | 14 | 00000000 | 0x0 |
| | 15 | 00000000 | 0x0 | 15 | 00000000 | 0x0 |
+---------+------+--------------+--------+------+--------------+--------+
| | 16 | 70014000 | 0x1000 | 16 | 70054000 | 0x1000 |
| | 17 | 70015000 | 0x1000 | 17 | 70055000 | 0x1000 |
| | 18 | 70016000 | 0x1000 | 18 | 70056000 | 0x1000 |
| Their | 19 | 70017000 | 0x1000 | 19 | 70057000 | 0x1000 |
| LI | 20 | 00000000 | 0x0 | 20 | 00000000 | 0x0 |
| Buffers | 21 | 00000000 | 0x0 | 21 | 00000000 | 0x0 |
| | 22 | 00000000 | 0x0 | 22 | 00000000 | 0x0 |
| | 23 | 00000000 | 0x0 | 23 | 00000000 | 0x0 |
+---------+------+--------------+--------+------+--------------+--------+
+-----+-----------------------------------------------+
| | SLICE 0 | SLICE 1 |
| +------------+----------+------------+----------+
| | Start addr | End addr | Start addr | End addr |
+-----+------------+----------+------------+----------+
| EXP | 70018000 | 7001C000 | 70058000 | 7005C000 |
| PRE | 7001C000 | 7001F800 | 7005C000 | 7005F800 |
+-----+------------+----------+------------+----------+
+---------------------+----------+----------+
| | SLICE 0 | SLICE 1 |
+---------------------+----------+----------+
| Default Drop Offset | 7001F800 | 7005F800 |
+---------------------+----------+----------+
Rootcause: missing buffer configuration for Express frames in
function: prueth_fw_offload_buffer_setup()
Details:
Driver implements two distinct buffer configuration functions that are
invoked based on the driver state and ICSSG firmware:-
- prueth_fw_offload_buffer_setup()
- prueth_emac_buffer_setup()
During initialization, driver creates standard network interfaces
(netdevs) and configures buffers via prueth_emac_buffer_setup().
This function properly allocates and configures all required memory
regions including:
- LI buffers
- Express packet buffers
- Preemptible packet buffers
However, when the driver transitions to an offload mode (switch/HSR/PRP),
buffer reconfiguration is handled by prueth_fw_offload_buffer_setup().
This function does not reconfigure the buffer regions required for
Express packets, leading to incorrect buffer allocation.
Fixes: abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
Signed-off-by: Himanshu Mittal <h-mittal1@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717094220.546388-1-h-mittal1@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fsl_mc_get_endpoint() function uses device_find_child() for
localization, which implicitly calls get_device() to increment the
device's reference count before returning the pointer. However, the
caller dpaa2_switch_port_connect_mac() fails to properly release this
reference in multiple scenarios. We should call put_device() to
decrement reference count properly.
As comment of device_find_child() says, 'NOTE: you will need to drop
the reference with put_device() after use'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 84cba72956fd ("dpaa2-switch: integrate the MAC endpoint support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717022309.3339976-3-make24@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The fsl_mc_get_endpoint() function uses device_find_child() for
localization, which implicitly calls get_device() to increment the
device's reference count before returning the pointer. However, the
caller dpaa2_eth_connect_mac() fails to properly release this
reference in multiple scenarios. We should call put_device() to
decrement reference count properly.
As comment of device_find_child() says, 'NOTE: you will need to drop
the reference with put_device() after use'.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250717022309.3339976-2-make24@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove hw_rx_no_dma_resources and eitr_param fields from struct
ixgbevf_adapter since these fields are never referenced in the driver.
Note that the interrupt throttle rate is controlled by the
rx_itr_setting and tx_itr_setting variables.
This change simplifies the ixgbevf driver by removing unused fields,
which improves maintainability.
Signed-off-by: Yuto Ohnuki <ytohnuki@amazon.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove following unused fields from struct igbvf_adapter that are never
referenced in the driver.
- blink_timer
- eeprom_wol
- fc_autoneg
- int_mode
- led_status
- mng_vlan_id
- polling_interval
- rx_dma_failed
- test_icr
- test_rx_ring
- test_tx_ring
- tx_dma_failed
- tx_fifo_head
- tx_fifo_size
- tx_head_addr
Also removed the following fields from struct igbvf_adapter since they
are never read or used after initialization by igbvf_probe() and igbvf_sw_init().
- bd_number
- rx_abs_int_delay
- tx_abs_int_delay
- rx_int_delay
- tx_int_delay
This changes simplify the igbvf driver by removing unused fields, which
improves maintenability.
Tested-by: Kohei Enju <enjuk@amazon.com>
Signed-off-by: Yuto Ohnuki <ytohnuki@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce support for a lowest priority wildcard (catch-all) rule in
ethtool's Network Flow Classification (NFC) for the igc driver. The
wildcard rule directs all unmatched network traffic, including traffic not
captured by Receive Side Scaling (RSS), to a specified queue. This
functionality utilizes the Default Queue feature available in I225/I226
hardware.
The implementation has been validated on Intel ADL-S systems with two
back-to-back connected I226 network interfaces.
Testing Procedure:
1. On the Device Under Test (DUT), verify the initial statistic:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 0
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 0
2. From the Link Partner, send 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
3. On the DUT, verify the packet reception on Queue 0:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 0
4. On the DUT, add a wildcard rule to route all packets to Queue 3:
$ sudo ethtool -N enp1s0 flow-type ether queue 3
5. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
6. Now, packets are routed to Queue 3 by the wildcard (Default Queue) rule:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 0
rx_queue_2_packets: 0
rx_queue_3_packets: 10
7. On the DUT, add a EtherType rule to route ARP packet to Queue 1:
$ sudo ethtool -N enp1s0 flow-type ether proto 0x0806 queue 1
8. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
9. Now, packets are routed to Queue 1 by the EtherType rule because it is
higher priority than the wildcard (Default Queue) rule:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 10
rx_queue_1_packets: 10
rx_queue_2_packets: 0
rx_queue_3_packets: 10
10. On the DUT, delete all the NFC rules:
$ sudo ethtool -N enp1s0 delete 63
$ sudo ethtool -N enp1s0 delete 64
11. From the Link Partner, send another 10 ARP packets:
$ arping -c 10 -I enp170s0 169.254.1.2
12. Now, packets are routed to Queue 0 because the value of Default Queue
is reset back to 0:
$ ethtool -S enp1s0 | grep rx_q.*packets
rx_queue_0_packets: 20
rx_queue_1_packets: 10
rx_queue_2_packets: 0
rx_queue_3_packets: 10
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Co-developed-by: Blanco Alcaine Hector <hector.blanco.alcaine@intel.com>
Signed-off-by: Blanco Alcaine Hector <hector.blanco.alcaine@intel.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move the RSS field definitions related to IPv4 and IPv6 UDP from igc.h to
igc_defines.h to consolidate the RSS field definitions in a single header
file, improving code organization and maintainability.
This refactoring does not alter the functionality of the driver but
enhances the logical grouping of related constants
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the VF handling code, parts of the code for lag can be broken out into
helper functions to reduce code duplication. Break this code out into
helper functions
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Previously the ice_add_prof() took an array of u8 and looped over it with
for_each_set_bit(), examining each 8 bit value as a bitmap.
This was just hard to understand and unnecessary, and was triggering
undefined behavior sanitizers with unaligned accesses within bitmap
fields (on our internal tools/builds). Since the @ptype being passed in
was already declared as a bitmap, refactor this to use native types with
the advantage of simplifying the code to use a single loop.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
CC: Jesse Brandeburg <jbrandeburg@cloudflare.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E835 is an enhanced version of the E830.
It continues to use the same set of commands, registers and interfaces
as other devices in the 800 Series.
Following device IDs are added:
- 0x1248: Intel(R) Ethernet Controller E835-CC for backplane
- 0x1249: Intel(R) Ethernet Controller E835-CC for QSFP
- 0x124A: Intel(R) Ethernet Controller E835-CC for SFP
- 0x1261: Intel(R) Ethernet Controller E835-C for backplane
- 0x1262: Intel(R) Ethernet Controller E835-C for QSFP
- 0x1263: Intel(R) Ethernet Controller E835-C for SFP
- 0x1265: Intel(R) Ethernet Controller E835-L for backplane
- 0x1266: Intel(R) Ethernet Controller E835-L for QSFP
- 0x1267: Intel(R) Ethernet Controller E835-L for SFP
Reviewed-by: Konrad Knitter <konrad.knitter@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Introduce the ICE_AQC_PORT_OPT_MAX_LANE_40G constant and update the code
to process this new option in both the devlink and the Admin Queue Command
GET PORT OPTION (opcode 0x06EA) message, similar to existing constants like
ICE_AQC_PORT_OPT_MAX_LANE_50G, ICE_AQC_PORT_OPT_MAX_LANE_100G, and so on.
This feature allows the driver to correctly report configuration options
for 2x40G on E823 and other cards in the future via devlink.
Example command:
devlink port split pci/0000:01:00.0/0 count 2
Example dmesg:
ice 0000:01:00.0: Available port split options and max port speeds (Gbps):
ice 0000:01:00.0: Status Split Quad 0 Quad 1
ice 0000:01:00.0: count L0 L1 L2 L3 L4 L5 L6 L7
ice 0000:01:00.0: 2 40 - - - 40 - - -
ice 0000:01:00.0: 2 50 - 50 - - - - -
ice 0000:01:00.0: 4 25 25 25 25 - - - -
ice 0000:01:00.0: 4 25 25 - - 25 25 - -
ice 0000:01:00.0: Active 8 10 10 10 10 10 10 10 10
ice 0000:01:00.0: 1 100 - - - - - - -
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The IRQ coalescing config currently reside only inside struct
idpf_q_vector. However, all idpf_q_vector structs are de-allocated and
re-allocated during resets. This leads to user-set coalesce configuration
to be lost.
Add new fields to struct idpf_vport_user_config_data to save the user
settings and re-apply them after reset.
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add cross timestamp support through virtchnl mailbox messages and directly,
through PCIe BAR registers. Cross timestamping assumes that both system
time and device clock time values are cached simultaneously, what is
triggered by HW. Feature is enabled for both ARM and x86 archs.
Signed-off-by: Milena Olech <milena.olech@intel.com>
Reviewed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the new virtchnl2 OP codes to communicate with the Control Plane to
add flow steering filters. We add the basic functionality for add/delete
with TCP/UDP IPv4 only. Support for other OP codes and protocols will be
added later.
Standard 'ethtool -N|--config-ntuple' should be used, for example:
# ethtool -N ens801f0d1 flow-type tcp4 src-ip 10.0.0.1 action 6
to route all IPv4/TCP traffic from IP 10.0.0.1 to queue 6.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add opcodes and corresponding message structure to add and delete
flow steering rules. Flow steering enables configuration
of rules to take an action or subset of actions based on a match
criteria. Actions could be redirect to queue, redirect to queue
group, drop packet or mark.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Co-developed-by: Dinesh Kumar <dinesh.kumar@intel.com>
Signed-off-by: Dinesh Kumar <dinesh.kumar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The "enum virtchnl2_cap_rss" will be used for negotiating flow
steering capabilities. Instead of adding a new enum, rename
virtchnl2_cap_rss to virtchnl2_flow_types. Also rename the enum's
constants.
Flow steering will use this enum in the next patches.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The DMA map functions can fail and should be tested for errors.
If the mapping fails, unmap and return an error.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250716094733.28734-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DMA map functions can fail and should be tested for errors.
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250716095733.37452-3-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VNIC testing on multi-core Power systems showed SAR stats drift
and packet rate inconsistencies under load.
Implements ndo_get_stats64 to provide safe aggregation of queue-level
atomic64 counters into rtnl_link_stats64 for use by tools like 'ip -s',
'ifconfig', and 'sar'. Switch to ndo_get_stats64 to align SAR reporting
with the standard kernel interface for retrieving netdev stats.
This removes redundant per-adapter stat updates, reduces overhead,
eliminates cacheline bouncing from hot path updates, and improves
the accuracy of reported packet rates.
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Brian King <bjking1@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
----
Changes since v3:
link to v3: https://www.spinics.net/lists/netdev/msg1107999.html
-- keep per queue counters as u64 (this patch) and drop off patch 1 in v3
Link: https://patch.msgid.link/20250716152115.61143-1-mmc@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qdisc_sleeping variable is declared as "struct Qdisc __rcu" and
as such needs proper annotation while accessing it.
Without rtnl_dereference(), the following error is generated by sparse:
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: warning:
incorrect type in initializer (different address spaces)
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: expected
struct Qdisc *qdisc
drivers/net/ethernet/mellanox/mlx5/core/en/qos.c:377:40: got struct
Qdisc [noderef] __rcu *qdisc_sleeping
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the following kdoc warning:
git ls-files *.[ch] | egrep drivers/net/ethernet/mellanox/mlx5/core/ |\
xargs scripts/kernel-doc --none
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:824: warning: cannot
understand function prototype: 'struct mlx5_esw_event_info '
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPSec hardware offload in legacy mode should not be affected by the
steering mode, hence it should also work properly with hmfs mode.
Remove steering mode validation when calculating the cap for packet
offload, this will also enable the missing cap MLX5_IPSEC_CAP_PRIO
needed for crypto offload.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1752675472-201445-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|