| Age | Commit message (Collapse) | Author |
|---|
|
This change pulls the call to fbnic_fw_xmit_cap_msg out of
fbnic_mbx_init_desc_ring and instead places it in the polling function for
getting the Tx ready. Doing that we can avoid the potential issue with an
interrupt coming in later from the firmware that causes it to get fired in
interrupt context.
Fixes: 20d2e88cc746 ("eth: fbnic: Add initial messaging to notify FW of our presence")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721876.499179.9839651602256668493.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There were a couple different issues found in fbnic_mbx_poll_tx_ready.
Among them were the fact that we were sleeping much longer than we actually
needed to as the actual FW could respond in under 20ms. The other issue was
that we would just keep polling the mailbox even if the device itself had
gone away.
To address the responsiveness issues we can decrease the sleeps to 20ms and
use a jiffies based timeout value rather than just counting the number of
times we slept and then polled.
To address the hardware going away we can move the check for the firmware
BAR being present from where it was and place it inside the loop after the
mailbox descriptor ring is initialized and before we sleep so that we just
abort and return an error if the device went away during initialization.
With these two changes we see a significant improvement in boot times for
the driver.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654721224.499179.2698616208976624755.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There was an issue in that if we were to shutdown we could be left with
a completion in flight as the mailbox went away. To address that I have
added an fbnic_mbx_evict_all_cmpl function that is meant to essentially
create a "broken pipe" type response so that all callers will receive an
error indicating that the connection has been broken as a result of us
shutting down the mailbox.
Fixes: 378e5cc1c6c6 ("eth: fbnic: hwmon: Add completion infrastructure for firmware requests")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654720578.499179.380252598204530873.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fbnic_mbx_flush_tx function had a number of issues.
First, we were waiting 200ms for the firmware to process the packets. We
can drop this to 20ms and in almost all cases this should be more than
enough time. So by changing this we can significantly reduce shutdown time.
Second, we were not making sure that the Tx path was actually shut off. As
such we could still have packets added while we were flushing the mailbox.
To prevent that we can now clear the ready flag for the Tx side and it
should stay down since the interrupt is disabled.
Third, we kept re-reading the tail due to the second issue. The tail should
not move after we have started the flush so we can just read it once while
we are holding the mailbox Tx lock. By doing that we are guaranteed that
the value should be consistent.
Fourth, we were keeping a count of descriptors cleaned due to the second
and third issues called out. That count is not a valid reason to be exiting
the cleanup, and with the tail only being read once we shouldn't see any
cases where the tail moves after the disable so the tracking of count can
be dropped.
Fifth, we were using attempts * sleep time to determine how long we would
wait in our polling loop to flush out the Tx. This can be very imprecise.
In order to tighten up the timing we are shifting over to using a jiffies
value of jiffies + 10 * HZ + 1 to determine the jiffies value we should
stop polling at as this should be accurate within once sleep cycle for the
total amount of time spent polling.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719929.499179.16406653096197423749.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have two issues that need to be addressed in our IRQ handling.
One is the fact that we can end up double-freeing IRQs in the event of an
exception handling error such as a PCIe reset/recovery that fails. To
prevent that from becoming an issue we can use the msix_vector values to
indicate that we have successfully requested/freed the IRQ by only setting
or clearing them when we have completed the given action.
The other issue is that we have several potential races in our IRQ path due
to us manipulating the mask before the vector has been truly disabled. In
order to handle that in the case of the FW mailbox we need to not
auto-enable the IRQ and instead will be enabling/disabling it separately.
In the case of the PCS vector we can mitigate this by unmapping it and
synchronizing the IRQ before we clear the mask.
The general order of operations after this change is now to request the
interrupt, poll the FW mailbox to ready, and then enable the interrupt. For
the shutdown we do the reverse where we disable the interrupt, flush any
pending Tx, and then free the IRQ. I am renaming the enable/disable to
request/free to be equivilent with the IRQ calls being used. We may see
additions in the future to enable/disable the IRQs versus request/free them
for certain use cases.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Fixes: 69684376eed5 ("eth: fbnic: Add link detection")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654719271.499179.3634535105127848325.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to prevent the device from throwing spurious writes and/or reads
at us we need to gate the AXI fabric interface to the PCIe until such time
as we know the FW is in a known good state.
To accomplish this we use the mailbox as a mechanism for us to recognize
that the FW has acknowledged our presence and is no longer sending any
stale message data to us.
We start in fbnic_mbx_init by calling fbnic_mbx_reset_desc_ring function,
disabling the DMA in both directions, and then invalidating all the
descriptors in each ring.
We then poll the mailbox in fbnic_mbx_poll_tx_ready and when the interrupt
is set by the FW we pick it up and mark the mailboxes as ready, while also
enabling the DMA.
Once we have completed all the transactions and need to shut down we call
into fbnic_mbx_clean which will in turn call fbnic_mbx_reset_desc_ring for
each ring and shut down the DMA and once again invalidate the descriptors.
Fixes: 3646153161f1 ("eth: fbnic: Add register init to set PCIe/Ethernet device config")
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654718623.499179.7445197308109347982.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Address to issues with the FW mailbox descriptor initialization.
We need to reverse the order of accesses when we invalidate an entry versus
writing an entry. When writing an entry we write upper and then lower as
the lower 32b contain the valid bit that makes the entire address valid.
However for invalidation we should write it in the reverse order so that
the upper is marked invalid before we update it.
Without this change we may see FW attempt to access pages with the upper
32b of the address set to 0 which will likely result in DMAR faults due to
write access failures on mailbox shutdown.
Fixes: da3cde08209e ("eth: fbnic: Add FW communication mechanism")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/174654717972.499179.8083789731819297034.stgit@ahduyck-xeon-server.home.arpa
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make veth_pool_store detect requested pool changes, close device if
necessary, update pool, and reopen device.
Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506160004.328347-1-davemarq@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When sending out any kind of traffic, it is essential that the driver
keeps reporting BQL of the number of bytes that have been sent so that
BQL can track the amount of data in the queue and prevents it from
overflowing. If BQL is not reported, the driver may continue sending
packets even when the queue is full, leading to packet loss, congestion
and decreased network performance. Currently this is missing in
emac_xmit_xdp_frame() and this patch fixes it.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-4-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add __netif_tx_lock() to ensure that only one packet is being
transmitted at a time to avoid race conditions in the netif_txq
struct and prevent packet data corruption. Failing to do so causes
kernel panic with the following error:
[ 2184.746764] ------------[ cut here ]------------
[ 2184.751412] kernel BUG at lib/dynamic_queue_limits.c:99!
[ 2184.756728] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
logs: https://gist.github.com/MeghanaMalladiTI/9c7aa5fc3b7fb03f87c74aad487956e9
The lock is acquired before calling emac_xmit_xdp_frame() and released after the
call returns. This ensures that the TX queue is protected from concurrent access
during the transmission of XDP frames.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-3-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_features demonstrates what all XDP capabilities are supported
on a given network device. The driver needs to set these xdp_features
flag to let the network stack know what XDP features a given driver
is supporting. These flags need to be set for a given ndev irrespective
of any XDP program being loaded or not.
Fixes: 62aa3246f462 ("net: ti: icssg-prueth: Add XDP support")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250506110546.4065715-2-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The official Airoha EN7581 firmware requires adding max_packet field in
ppe_mbox_data struct while the unofficial one used to develop the Airoha
EN7581 flowtable support does not require this field.
This patch does not introduce any real backwards compatible issue since
EN7581 fw is not publicly available in linux-firmware or other
repositories (e.g. OpenWrt) yet and the official fw version will use this
new layout. For this reason this change needs to be backported.
Moreover, make explicit the padding added by the compiler introducing
the rsv array in init_info struct.
At the same time use u32 instead of int for init_info and set_info
struct definitions in ppe_mbox_data struct.
Fixes: 23290c7bc190d ("net: airoha: Introduce Airoha NPU support")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250506-airoha-en7581-fix-ppe_mbox_data-v5-1-29cabed6864d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use Device Serial Number instead of PCI bus/device/function for
the index of struct ice_adapter.
Functions on the same physical device should point to the very same
ice_adapter instance, but with two PFs, when at least one of them is
PCI-e passed-through to a VM, it is no longer the case - PFs will get
seemingly random PCI BDF values, and thus indices, what finally leds to
each of them being on their own instance of ice_adapter. That causes them
to don't attempt any synchronization of the PTP HW clock usage, or any
other future resources.
DSN works nicely in place of the index, as it is "immutable" in terms of
virtualization.
Fixes: 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on the same NIC")
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505161939.2083581-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove redundant PSE reset.
When setting FE register there is no need to reset PSE,
doing so may cause FE to work abnormal.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/3a5223473e086a4b54a2b9a44df7d9ddcc2bc75a
Fixes: dee4dd10c79aa ("net: ethernet: mtk_eth_soc: ppe: add support for multiple PPEs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://patch.msgid.link/18f0ac7d83f82defa3342c11ef0d1362f6b81e88.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The purpose of resetting the TX queue is to reset the byte and packet
count as well as to clear the software flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/319c0d9905579a46dc448579f892f364f1f84818
Fixes: f63959c7eec31 ("net: ethernet: mtk_eth_soc: implement multi-queue support for per-port queues")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/c9ff9adceac4f152239a0f65c397f13547639175.1746406763.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix the tracking of rtnl_link_stats.tx_dropped. The counter
`tmi.drop.frames` is being double counted whereas, the counter
`tti.cm_drop.frames` is being skipped.
Fixes: f2957147ae7a ("eth: fbnic: add support for TTI HW stats")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20250503020145.1868252-1-mohsin.bashr@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Added KUnit tests for ibmveth_remove_buffer_from_pool and
ibmveth_rxq_get_buffer under new IBMVETH_KUNIT_TEST config option.
Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250501194944.283729-4-davemarq@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reset the adapter through new function ibmveth_reset, called in
WARN_ON situations. Removed conflicting and unneeded forward
declaration.
Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com>
Link: https://patch.msgid.link/20250501194944.283729-3-davemarq@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Made struct ibmveth_adapter follow indentation rules
Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250501194944.283729-2-davemarq@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove the speed_mode_2500() platform method which is no longer used
or necessary, being superseded by the more flexible get_interfaces()
method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASM3-0021R3-2B@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TGL platforms support either SGMII or 2500BASE-X, which is determined
by reading a SERDES register.
Thus, plat->phy_interface (and phylink's supported_interfaces) depend
on this. Use the new .get_interfaces() method to set both
plat->phy_interface and the supported_interfaces bitmap.
This removes the only user of the .speed_mode_2500() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASLx-0021Qs-Uz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the initialisation of plat->phy_interface to tgl_common_data()
as all callers set this same interface mode. This moves it to a
single location to make the change to get_interfaces() more obvious.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASLs-0021Qk-Qt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a get_interfaces() platform method to allow platforms to indicate
to phylink which interface modes they support - which then allows
phylink to validate on initialisation that the configured PHY interface
mode is actually supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1uASLn-0021Qd-Mi@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid using a local variable for priv->plat->phy_interface as this
may be modified in the .get_interfaces() method added in a future
commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASLi-0021QX-HG@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use a local variable for priv->phylink_config in stmmac_phy_setup()
which makes the code a bit easier to read, allowing some lines to be
merged.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1uASLd-0021QR-Cu@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 52358dd63e34 ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e34 ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MediaTek MT7988 SoC comes with an single built-in Ethernet PHY for
2500Base-T/1000Base-T/100Base-TX/10Base-T link partners in addition to
the built-in 1GE switch. The built-in PHY only supports full duplex.
Add muxes allowing to select GMAC2->2.5G PHY path and add basic support
for XGMAC as the built-in 2.5G PHY is internally connected via XGMII.
The XGMAC features will also be used by 5GBase-R, 10GBase-R and USXGMII
SerDes modes which are going to be added once support for standalone PCS
drivers is in place.
In order to make use of the built-in 2.5G PHY the appropriate PHY driver
as well as (proprietary) PHY firmware has to be present as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/9072cefbff6db969720672ec98ed5cef65e8218c.1745715380.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-29 (igb, igc, ixgbe, idpf)
For igb:
Kurt Kanzenbach adds linking of IRQs and queues to NAPI instances and
adds persistent NAPI config. Lastly, he removes undesired IRQs that
occur while busy polling.
For igc:
Kurt Kanzenbach switches the Tx mode for MQPRIO offload to harmonize the
current implementation with TAPRIO.
For ixgbe:
Jedrzej adds separate ethtool ops for E610 devices to account for device
differences.
Slawomir adds devlink region support for E610 devices.
For idpf:
Mateusz assigns and utilizes the ptype field out of libeth_rqe_info.
Michal removes unreachable code.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: remove unreachable code from setting mailbox
idpf: assign extracted ptype to struct libeth_rqe_info field
ixgbe: devlink: add devlink region support for E610
ixgbe: add E610 .set_phys_id() callback implementation
ixgbe: apply different rules for setting FC on E610
ixgbe: add support for ACPI WOL for E610
ixgbe: create E610 specific ethtool_ops structure
igc: Change Tx mode for MQPRIO offloading
igc: Limit netdev_tc calls to MQPRIO
igb: Get rid of spurious interrupts
igb: Add support for persistent NAPI config
igb: Link queues to NAPI instances
igb: Link IRQs to NAPI instances
====================
Link: https://patch.msgid.link/20250429234651.3982025-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc5).
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LEN_MASK for CMD_RTS doesn't cover the whole parameter mask.
The Bit 11 is reserved, so adjust LEN_MASK accordingly.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d4b ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-29 (idpf, igc)
For idpf:
Michal fixes error path handling to remove memory leak.
Larysa prevents reset from being called during shutdown.
For igc:
Jake adjusts locking order to resolve sleeping in atomic context.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: fix lock order in igc_ptp_reset
idpf: protect shutdown from reset
idpf: fix potential memory leak on kcalloc() failure
====================
Link: https://patch.msgid.link/20250429221034.3909139-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor")
Signed-off-by: Sathesh B Edara <sedara@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recent updates to the PTP part of bnxt changed the way PTP FIFO is
cleared, skbs waiting for TX timestamps are now cleared during
ndo_close() call. To do clearing procedure, the ptp structure must
exist and point to a valid address. Module destroy sequence had ptp
clear code running before netdev close causing invalid memory access and
kernel crash. Change the sequence to destroy ptp structure after device
close.
Fixes: 8f7ae5a85137 ("bnxt_en: improve TX timestamping FIFO configuration")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Closes: https://lore.kernel.org/netdev/CAMArcTWDe2cd41=ub=zzvYifaYcYv-N-csxfqxUvejy_L0D6UQ@mail.gmail.com/
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20250430170343.759126-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace ice driver specific DSCP mapping number defines
ICE_DSCP_NUM_VAL and IIDC_MAX_DSCP_MAPPING with
an equivalent kernel define DSCP_MAX.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In preparation of supporting more than a single core PCI driver
for RDMA, break the iidc_rdma.h header file into two more focused
headers.
Only the elements universal to all Intel drivers will remain in
the generic iidc_rdma.h header. Move the ice specific information
to an ice specific header file named iidc_rdma_ice.h.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In preparation of supporting more than a single core PCI driver
for RDMA, homogenize naming to iidc_rdma_* and IIDC_RDMA_*
form.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
To prepare for the IDC upgrade to support different CORE
PCI drivers, rename header file from iidc.h to iidc_rdma.h
since this files functionality is specifically for RDMA support.
Use net/dscp.h include in irdma osdep.h and DSCP_MAX type.h,
instead of iidc header and define.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length")
Reported-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is similar to the last patch to delay the
pci_alloc_irq_vectors() call in the AER path until after calling
bnxt_reserve_rings(). bnxt_reserve_rings() needs to properly map
the MSIX table first before we call pci_alloc_irq_vectors() which
may immediately write to the MSIX table in some architectures.
Move the bnxt_init_int_mode() call from bnxt_io_slot_reset() to
bnxt_io_resume() after calling bnxt_reserve_rings().
With this change, the AER path may call bnxt_open() ->
bnxt_hwrm_if_change() with bp->irq_tbl set to NULL. bp->irq_tbl is
cleared when we call bnxt_clear_int_mode() in bnxt_io_slot_reset().
So we cannot use !bp->irq_tbl to detect aborted FW reset. Add a
new BNXT_FW_RESET_STATE_ABORT to detect aborted FW reset in
bnxt_hwrm_if_change().
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
