summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath9k
AgeCommit message (Collapse)Author
2009-03-05ath9k: Fix hw crypto configuration for TKIP in AP modeJouni Malinen
Incorrect Michael MIC key (RX, should have been TX) was set for the group key in AP mode. This resulted in all broadcast frames triggering Michael MIC errors and eventual TKIP countermeasures. The change here sets the correct Michael MIC key based on whether the local end is the authenticator (well, AP for now). Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Tested-by: Pat Erley <pat-lkml@erley.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05ath9k: Remove ununsed ack duration stuff with long/short preambleVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05ath9k: Configure Power control register appropriately for h/w with 4k eepromVasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-03-05ath9k: Add module parameter to disable hardware cryptoJouni Malinen
nohwcrypt=1 module parameter can now be used to disable hardware crypto in ath9k. While the hardware acceleration handles most cases, it may be useful to be able to force mac80211 software implementation to be used for some tests, e.g., with virtual interface combinations that may not yet be supported in the key cache configuration. In addition, this allows management frame protection to be tested with older hardware revisions. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Unlock sc->mutex on error pathJouni Malinen
An error path in ath9k_add_interface() did not unlock the sc->mutex and could leave the driver in quite unresponsive state. Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: fix 802.11g conformance test limit typoBob Copeland
802.11g is in 2 ghz band, not 5 ghz. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: follow beacon hints on reg_notifier when world roamingLuis R. Rodriguez
If we are roaming we allow to follow beacon hints. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27cfg80211: move all regulatory hints to workqueueLuis R. Rodriguez
All regulatory hints (core, driver, userspace and 11d) are now processed in a workqueue. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Add appropriate ANI values for AP modeSujith
The short calibration interval is different for AP mode, fix this. Also, the timer should be rearmed in the calibration routine during scanning. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix PCI shutdown sequenceSujith
pci_release_region() has to be called after the device has been disabled. Also remove a stray __init attribute. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix bug in EEPROM chainmask retrievalSujith
Using wrong chainmasks would have an adverse impact on performance. This patch fixes chainmask retrieval for non-PCIE cards. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Add PER to RC debug statisticsSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Remove multiple macro occurrencesSujith
OLC_FOR_AR9280_20_LATER is defined in multiple places, move it to a common location. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Don't reset TSF after scanning automaticallyAlina Friedrichsen
Reset automatically the TSF on re-enabling beaconing after scanning in IBSS mode causes several problems. For example a new created IBSS network can't age before an other node has joined, because scans are done automatically in that case. And several other strange bugs more... The TSF reset is done manually in the higher level mac80211 code in the cases were it's needed, so we don't need to do it here. Signed-off-by: Alina Friedrichsen <x-alina@gmx.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Filter out beacons from other BSS in STA modeVasanthakumar Thiagarajan
Passing beacons received from other BSS to s/w in non-scanning state is unnecessary in STA mode. This patch filters them out in h/w. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix PTK/GTK handshake timeoutVasanthakumar Thiagarajan
Some APs don't start BA negotiation with the client before it is done with the key handshake in WPA/RSN. With those APs, key handshake times out if EAPOL frames are sent after addba request. So defer the BA negotiation until we are done with tx/rx of all EAPOL frames. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Use beacon interval directlySujith
Setting up the CAB queue requires only the beacon interval, remove the function ath_get_beaconconfig() which is redundant. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Remove ath_txq_depth and get the queue depth directlySujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Remove a few unused capability macrosSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Initialize channel change timeSujith
Set channel change time to 5ms, this will improve scan results. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix antenna assignment bug in TX status processingSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix HW wait timeoutSujith
RX and calibration have different timeout requirements. This patch fixes it by changing the HW wait routine to accept a timeout value. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Program the RTC registers correctlySujith
This patch programs the RTC registers of AR9100 chipsets correctly during chip reset. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: move common regulatory code out of if() branchesBob Copeland
Both branches of the regulatory check in ath_attach() set up a custom regulatory domain and apply radar and world flags, so extract those into a single path. While at it, fix a couple of spelling errors and an unnecessary extra pointer traversal. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: remove prototype for ath9k_regd_get_current_countryBob Copeland
ath9k_regd_get_current_country() doesn't exist. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: remove ath9k_regd_get_rd()Bob Copeland
The function ath9k_regd_get_rd() is unused. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: convert isWwrSKU macro into C codeBob Copeland
Write isWwrSKU as an inline function and nix the camel-case to make the routine slightly clearer. Change its argument to take the regd value directly so it can eventually be used by ath5k as well. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: save a few calls to ath9k_regd_get_eepromRDBob Copeland
Since we already have a stack variable to track the eeprom regd, we can grab it up front it and save three calls to fetch it again. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: remove write-only current_rd_inuseBob Copeland
The current_rd_inuse regulatory value is assigned but not used anywhere. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Add open loop control supportSenthil Balasubramanian
This patch adds Open Loop Control support for Atheros chipsets that supports open loop power control. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Decrease minimum NF thresholdSujith
The existing value was too conservative, causing the history buffer not to be updated. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix incorrect noise floor reading for 4k EEPROMSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix bug in disabling MIB countersSujith
This patch fixes a bug in ANI, where the MIB counters were being cleared before the stats were updated. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Initialize AGC calibration properlySujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Enable TSF Out of Range InterruptSujith
This patch lays the groundwork for handling TSF Out of Range interrupt, which will be used for power save later on. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Enable Fractional N modeSujith
This patch enables Fractional N mode for all channel if the EEPROM says so, and also fixes the INI only when the device is not a 2 GHz only capable device. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Fix rd_ext EEPROM capability for AR9285Sujith
AR9285 chipsets have a different EEPROM layout, handle this appropriately when populating the rd_ext capability. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-27ath9k: Store the correct max TX power levelSujith
This patch fixes a bug where the max power level was being calculated incorrectly. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-25Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/orinoco/orinoco.c
2009-02-23ath9k: Fix panic upon attach failureVasanthakumar Thiagarajan
[246916.338046] [246916.338048] Pid: 29265, comm: insmod Not tainted (2.6.29-rc4-wl #64) 9461DUU [246916.338051] EIP: 0060:[<c02ca274>] EFLAGS: 00010202 CPU: 0 [246916.338055] EIP is at rollback_registered+0x24/0x220 [246916.338057] EAX: 00000001 EBX: 00000000 ECX: 00000000 EDX: f122e8fc [246916.338059] ESI: 00000000 EDI: 00000000 EBP: f6595d30 ESP: f6595d1c [246916.338062] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [246916.338064] Process insmod (pid: 29265, ti=f6594000 task=f7343fe0 task.ti=f6594000) [246916.338067] Stack: [246916.338068] c04a2920 22222222 f6595d48 00000000 f122f080 f6595d48 c02ca489 f122e8fc [246916.338076] f122e220 f122f080 f122e220 f6595d5c f8a03156 f122e220 f122f080 f122e220 [246916.338085] f6595d80 f87359af f122f080 00002000 f874e129 f122f150 f122f080 f6290000 [246916.338094] Call Trace: [246916.338096] [<c02ca489>] ? unregister_netdevice+0x19/0x70 [246916.338100] [<f8a03156>] ? ieee80211_unregister_hw+0x36/0xd0 [mac80211] [246916.338112] [<f87359af>] ? ath_detach+0xcf/0x250 [ath9k] [246916.338127] [<f8735d9c>] ? ath_attach+0x26c/0x740 [ath9k] [246916.338139] [<f873c33a>] ? ath_pci_probe+0x13a/0x310 [ath9k] [246916.338151] [<c0233e28>] ? _raw_spin_unlock+0x68/0x80 [246916.338158] [<c023ab8e>] ? local_pci_probe+0xe/0x10 [246916.338162] [<c023b8e0>] ? pci_device_probe+0x60/0x80 [246916.338169] [<c029e042>] ? driver_probe_device+0x82/0x1b0 [246916.338174] [<c029e1f9>] ? __driver_attach+0x89/0x90 [246916.338180] [<c029d97b>] ? bus_for_each_dev+0x4b/0x70 [246916.338184] [<c023b820>] ? pci_device_remove+0x0/0x40 [246916.338190] [<c029ded9>] ? driver_attach+0x19/0x20 [246916.338193] [<c029e170>] ? __driver_attach+0x0/0x90 [246916.338197] [<c029d317>] ? bus_add_driver+0x1b7/0x230 [246916.338203] [<c023b820>] ? pci_device_remove+0x0/0x40 [246916.338206] [<c029e399>] ? driver_register+0x69/0x140 [246916.338212] [<f859d000>] ? ath9k_init+0x0/0x54 [ath9k] [246916.338221] [<c023bb4e>] ? __pci_register_driver+0x4e/0x90 [246916.338225] [<f859d000>] ? ath9k_init+0x0/0x54 [ath9k] [246916.338232] [<f859d06b>] ? ath_pci_init+0x17/0x19 [ath9k] [246916.338238] [<f859d017>] ? ath9k_init+0x17/0x54 [ath9k] [246916.338245] [<c017148e>] ? tracepoint_update_probe_range+0x7e/0xb0 [246916.338249] [<c010111a>] ? do_one_initcall+0x2a/0x170 [246916.338252] [<c0149f26>] ? up_read+0x16/0x30 [246916.338256] [<c014aa9d>] ? __blocking_notifier_call_chain+0x4d/0x60 [246916.338265] [<c0162b1a>] ? sys_init_module+0x8a/0x1c0 [246916.338269] [<c022f888>] ? trace_hardirqs_on_thunk+0xc/0x10 [246916.338272] [<c0103ebf>] ? sysenter_do_call+0x12/0x43 [246916.338276] Code: 8d bc 27 00 00 00 00 55 89 e5 56 89 c6 53 83 ec 0c a1 74 27 4a c0 85 c0 0f 85 4b 01 00 00 e8 04 7d 00 00 85 c0 0f 84 c9 01 00 00 <8b> 86 18 03 00 00 85 c0 0f 84 86 01 00 00 83 e8 01 0f 85 71 01 [246916.338328] EIP: [<c02ca274>] rollback_registered+0x24/0x220 SS:ESP 0068:f6595d1c [246916.338335] ---[ end trace 76357c56a75ea34e ]--- Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-17drivers/net/wireless/ath9k: fix sparse warnings: Should it be static?Hannes Eder
Impact: Make symbols static. Fix this sparse warnings: drivers/net/wireless/ath9k/eeprom.c:1343:5: warning: symbol 'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:1372:19: warning: symbol 'eep_4k_ops' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2649:5: warning: symbol 'ath9k_hw_def_get_spur_channel' was not declared. Should it be static? drivers/net/wireless/ath9k/eeprom.c:2678:19: warning: symbol 'eep_def_ops' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-13ath9k: add udelay() for AR5416 on ath9k_hw_configpcipowersave()Luis R. Rodriguez
We need the udelay() for all families, including AR5416. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: add comments for ath9k_hw_configpcipowersave()Luis R. Rodriguez
This is used for ASPM. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Remove all the useless ah_ variable prefixesSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Cleanup EEPROM operationsSujith
This patch removes the various function pointer assignments and unifies them in a single ops structure. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Add callbacks hooks for EEPROM operationsSujith
This is preparatory work for removing the individual function pointer assignments in eeprom.c Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Merge ath_hal and ath_hal_5416 structuresSujith
Finally, merge these structures and have a single HW specific data structure. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Remove duplicate variablesSujith
A few variables (bssid, bssidmask, curaid) were duplicated in struct ath_softc and in ath_hal, remove them. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Move regulatory information to a separate structureSujith
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-13ath9k: Store HW version information in a separate structureSujith
This patch moves all the HW version/revision specific information into a separate structure. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit (git 2.34.1) at 2025-07-28 05:20:52 +0000