| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following sparse warning in mt76x02_mac_write_txwi and
mt76x02_mac_tx_rate_val routines:
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:237:19:
warning: restricted __le16 degrades to intege
warning: cast from restricted __le16
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c:383:28:
warning: incorrect type in assignment (different base types)
expected restricted __le16 [usertype] rate
got unsigned long
Fixes: db9f11d3433f7 ("mt76: store wcid tx rate info in one u32 reduce locking")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix MIB tx-rx MIB counters for survey-dump reporting.
Fixes: 163f4d22c118d ("mt76: mt7921: add MAC support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:10: error: implicit
conversion from enumeration type 'enum mt76_cipher_type' to different
enumeration type 'enum mcu_cipher_type' [-Werror,-Wenum-conversion]
return MT_CIPHER_NONE;
~~~~~~ ^~~~~~~~~~~~~~
Fixes: c368362c36d3 ("mt76: fix iv and CCMP header insertion")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7921 is mainly used in NB, CE and IoT application where battery life is
much concerned so the patch enabled PCIe ASPM by default to shut off the
clocks related PCIe as much as possible when MT7921 is either in suspend
state or in runtime pm to lower power consumption.
We still leave disable aspm as an option with module_param for users to
disable ASPM if necessary.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The mistaken structure is introduced since we added the GTK rekey offload
to mt7663. The patch fixes mt76_connac_gtk_rekey_tlv structure according
to the MT7663 and MT7921 firmware we have submitted into
linux-firmware.git.
Fixes: b47e21e75c80 ("mt76: mt7615: add gtk rekey offload support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Leon Yen <Leon.Yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
It will cause maximum connectable STA to be one less
when calling mt76_wcid_alloc with parameter MT7915_WTBL_STA - 1.
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Zero out all the unused members of "req" so that we don't disclose
stack information.
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the following sparse warning in mt7615_mac_write_txwi routine:
drivers/net/wireless/mediatek/mt76/mt7615/mac.c:758:17:
warning: incorrect type in assignment
expected restricted __le32 [usertype]
got unsigned long
Fixes: 04b8e65922f63 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Fixes: d4bf77bd74930 ("mt76: mt7615: introduce mt7663u support to mt7615_write_txwi")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the following sparse warning in mt7921_update_txs routine:
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7921/mac.c:752:31:
warning: restricted __le32 degrades to integer
Fixes: e5bca8c5d2cd3 ("mt76: mt7921: improve code readability for mt7921_update_txs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the following sparse warning in mt7915_mac_add_txs_skb routine:
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:29:
warning: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:1235:23:
warning: restricted __le32 degrades to integer
Fixes: 3de4cb1756565 ("mt76: mt7915: add support for tx status reporting")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7921_mcu_tx_done_event
Do not grab the spinlock in mt7921_mcu_tx_done_event routine if not
necessary.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix endianness in mt7921_mcu_tx_done_event event reported by the
firmware.
Fixes: 3cce2b98e0241 ("mt76: mt7921: introduce mac tx done handling")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The 0-element arrays that are used as memcpy() destinations are actually
flexible arrays. Adjust their structures accordingly so that memcpy()
can better reason able their destination size (i.e. they need to be seen
as "unknown" length rather than "zero").
In some cases, use of the DECLARE_FLEX_ARRAY() helper is needed when a
flexible array is alone in a struct.
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Nilesh Javali <njavali@marvell.com>
Cc: Manish Rangankar <mrangankar@marvell.com>
Cc: GR-QLogic-Storage-Upstream@marvell.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Schilhabel <florian.c.schilhabel@googlemail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Fabio Aiuto <fabioaiuto83@gmail.com>
Cc: Ross Schmidt <ross.schm.dev@gmail.com>
Cc: Marco Cesati <marcocesati@gmail.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
In support of enabling -Warray-bounds and -Wzero-length-bounds and
correctly handling run-time memcpy() bounds checking, replace all
open-coded flexible arrays (i.e. 0-element arrays) in unions with the
DECLARE_FLEX_ARRAY() helper macro.
This fixes warnings such as:
fs/hpfs/anode.c: In function 'hpfs_add_sector_to_btree':
fs/hpfs/anode.c:209:27: warning: array subscript 0 is outside the bounds of an interior zero-length array 'struct bplus_internal_node[0]' [-Wzero-length-bounds]
209 | anode->btree.u.internal[0].down = cpu_to_le32(a);
| ~~~~~~~~~~~~~~~~~~~~~~~^~~
In file included from fs/hpfs/hpfs_fn.h:26,
from fs/hpfs/anode.c:10:
fs/hpfs/hpfs.h:412:32: note: while referencing 'internal'
412 | struct bplus_internal_node internal[0]; /* (internal) 2-word entries giving
| ^~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_fd.c: In function 'es58x_fd_tx_can_msg':
drivers/net/can/usb/etas_es58x/es58x_fd.c:360:35: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'u8[0]' {aka 'unsigned char[]'} [-Wzero-length-bounds]
360 | tx_can_msg = (typeof(tx_can_msg))&es58x_fd_urb_cmd->raw_msg[msg_len];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/can/usb/etas_es58x/es58x_core.h:22,
from drivers/net/can/usb/etas_es58x/es58x_fd.c:17:
drivers/net/can/usb/etas_es58x/es58x_fd.h:231:6: note: while referencing 'raw_msg'
231 | u8 raw_msg[0];
| ^~~~~~~
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Cc: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Cc: Rohit Maheshwari <rohitm@chelsio.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Mordechay Goodstein <mordechay.goodstein@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: linux-crypto@vger.kernel.org
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: bpf@vger.kernel.org
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # drivers/net/can/usb/etas_es58x/*
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
coccicheck complains about the use of snprintf() in sysfs show functions.
Fix the coccicheck warning:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634095651-4273-1-git-send-email-wangqing@vivo.com
|
|
The function rtw89_mac_enable_bb_rf is a void return type, so there is
no return error code to ret, so the following check for an error in ret
is redundant dead code and can be removed.
Addresses-Coverity: ("Logically dead code")
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015152113.33179-1-colin.king@canonical.com
|
|
There are two spelling mistakes in rtw89_debug messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015105004.11817-1-colin.king@canonical.com
|
|
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
|
|
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr
|
|
The variable ret is being initialized with a value that is never read,
it is assigned later on with a different value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007234153.31222-1-colin.king@canonical.com
|
|
The variable version is being initialized with a value that is
never read, it is being updated afterwards in both branches of
an if statement. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007163722.20165-1-colin.king@canonical.com
|
|
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
|
|
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Fixes: 02256930d9b8 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org
|
|
The devm_kmemdup() function doesn't return error pointers, it returns
NULL on error.
Fixes: eb3a97a69be8 ("ath9k: fetch calibration data via nvmem subsystem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011123533.GA15188@kili
|
|
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011054919.77071-1-bqiang@codeaurora.org
|
|
The common DT property can be used to limit the available channels
but ath9k has to manually call wiphy_read_of_freq_limits().
I would have put this into ath9k_of_init(). But it didn't work there.
The reason is that in ath9k_of_init() the channels and bands are not yet
registered in the wiphy struct. So there isn't any channel to flag as
disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211009212847.1781986-1-chunkeey@gmail.com
|
|
Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.
This is a theoretical fix found during code review, no visible impact.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org
|
|
When doing "rmmod ath11k_pci", ath11k performs global SOC reset
and MHI reset, where 0 address access is captured by IOMMU. See
log below:
...
[ 133.953860] ath11k_pci 0000:02:00.0: setting mhi state: DEINIT(1)
[ 133.959714] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
[ 133.973854] ath11k_pci 0000:02:00.0: MHISTATUS 0xff04
[ 133.974095] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
...
This issue is also observed in SSR process, cause a similar
sequence as above is performed.
Such an invalid access occurs because, during rmmod or SSR, MSI
address is cleared but HW MSI functionality not disabled, thus HW
target is able to raise an MSI transaction with 0 as MSI address.
So it can be fixed by simply disabling MSI before reset. For SSR,
since MSI functionality is still needed after target is brought
back, we need to reenable it.
Also change naming of some interfaces related.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-5-jouni@codeaurora.org
|
|
channel_detector_create()
kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
channel_detector_exit(dpd, cd);
In channel_detector_exit(), cd->detectors is dereferenced through:
struct pri_detector *de = cd->detectors[i];
To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
|
|
Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006181204.GA913553@embeddedor
|
|
Variable fw_size is being assigned a value that is never read and
being re-assigned a new value in the next statement. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Fixes: 336e7b53c82f ("ath11k: clean up BDF download functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006105529.1011239-1-colin.king@canonical.com
|
|
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: ef1a628d83fc ("b43: Implement dynamic PHY API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073621.GE8404@kili
|
|
The problem is that "channel" is an unsigned int, when it's less 5 the
value of "channel - 5" is not a negative number as one would expect but
is very high positive value instead.
This means that "start" becomes a very high positive value. The result
of that is that we never enter the "for (i = start; i <= end; i++) {"
loop. Instead of storing the result from b43legacy_radio_aci_detect()
it just uses zero.
Fixes: 75388acd0cd8 ("[B43LEGACY]: add mac80211-based driver for legacy BCM43xx devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006073542.GD8404@kili
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
|
|
Stephen reported that ath11k was failing to build on m68k and xtensa:
In file included from <command-line>:0:0:
In function 'ath11k_peer_assoc_h_smps',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2362:2:
include/linux/compiler_types.h:317:38: error: call to '__compiletime_assert_650' declared with attribute error: FIELD_GET: type of reg too small for mask
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/compiler_types.h:298:4: note: in definition of macro '__compiletime_assert'
prefix ## suffix(); \
^
include/linux/compiler_types.h:317:2: note: in expansion of macro '_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^
include/linux/bitfield.h:52:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \
^
include/linux/bitfield.h:108:3: note: in expansion of macro '__BF_FIELD_CHECK'
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/net/wireless/ath/ath11k/mac.c:2079:10: note: in expansion of macro 'FIELD_GET'
smps = FIELD_GET(IEEE80211_HE_6GHZ_CAP_SM_PS,
Fix the issue by using le16_get_bits() to specify the size explicitly.
Fixes: 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in an ath11k_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006083217.349596-1-colin.king@canonical.com
|
|
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverity complains that a constant variable guards dead code. In fact,
mpdu_buf is set NULL and never updated.
4834err_merge_fail:
null: At condition mpdu_buf, the value of mpdu_buf must be NULL.
dead_error_condition: The condition mpdu_buf cannot be true.
CID 92162 (#1 of 1): 'Constant' variable guards dead code (DEADCODE)
dead_error_line: Execution cannot reach the expression decap_format !=
DP_RX_DECAP_TYPE_RAW inside this statement: if (mpdu_buf && decap_forma....
Local variable mpdu_buf is assigned only once, to a constant value, making it
effectively constant throughout its scope. If this is not the intent, examine
the logic to see if there is a missing assignment that would make mpdu_buf not
remain constant.
4835 if (mpdu_buf && decap_format != DP_RX_DECAP_TYPE_RAW) {
Fix this by removing mpdu_buf and unreachable code.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927150743.19816-1-tim.gardner@canonical.com
|
|
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt
19.07 we could force a silent restart of a device with no serial
output when we were sending a high amount of UDP traffic (iperf3 at 80
MBit/s in both directions from external hosts, saturating the wifi and
causing a load of about 4.5 to 6) and were then triggering an
ath9k_queue_reset().
Further debugging showed that the restart was caused by the ath79
watchdog. With disabled watchdog we could observe that the device was
constantly going into ath_isr() interrupt handler and was returning
early after the ATH_OP_HW_RESET flag test, without clearing any
interrupts. Even though ath9k_queue_reset() calls
ath9k_hw_kill_interrupts().
With JTAG we could observe the following race condition:
1) ath9k_queue_reset()
...
-> ath9k_hw_kill_interrupts()
-> set_bit(ATH_OP_HW_RESET, &common->op_flags);
...
<- returns
2) ath9k_tasklet()
...
-> ath9k_hw_resume_interrupts()
...
<- returns
3) loops around:
...
handle_int()
-> ath_isr()
...
-> if (test_bit(ATH_OP_HW_RESET,
&common->op_flags))
return IRQ_HANDLED;
x) ath_reset_internal():
=> never reached <=
And in ath_isr() we would typically see the following interrupts /
interrupt causes:
* status: 0x00111030 or 0x00110030
* async_cause: 2 (AR_INTR_MAC_IPQ)
* sync_cause: 0
So the ath9k_tasklet() reenables the ath9k interrupts
through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just
disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED
without actually clearing the interrupt.
To fix this IRQ storm also clear/disable the interrupts again when we
are in reset state.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset")
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue
|
|
Sometimes, in yet unknown cases the wifi chip stops working. To allow a
watchdog in userspace to easily and quickly reset the wifi chip, add the
according functionality to userspace. A reset can then be triggered
via:
$ echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/reset
The number of user resets can further be tracked in the row "User reset"
in the same file.
So far people usually used "iw scan" to fix ath9k chip hangs from
userspace. Which triggers the ath9k_queue_reset(), too. The reset file
however has the advantage of less overhead, which makes debugging bugs
within ath9k_queue_reset() easier.
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914192515.9273-2-linus.luessing@c0d3.blue
|
|
When rebooting on sc7180 Trogdor devices I see the following crash from
the wifi driver.
ath10k_snoc 18800000.wifi: firmware crashed! (guid 83493570-29a2-4e98-a83e-70048c47669c)
This is because a modem stop event looks just like a firmware crash to
the driver, the qmi connection is closed in both cases. Use the qcom ssr
notifier block to stop treating the qmi connection close event as a
firmware crash signal when the modem hasn't actually crashed. See
ath10k_qmi_event_server_exit() for more details.
This silences the crash message seen during every reboot.
Fixes: 3f14b73c3843 ("ath10k: Enable MSA region dump support for WCN3990")
Cc: Youghandhar Chintala <youghand@codeaurora.org>
Cc: Abhishek Kumar <kuabhs@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Tested-By: Youghandhar Chintala <youghand@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210922233341.182624-1-swboyd@chromium.org
|
|
ath.git patches for v5.16. Major changes:
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
|
|
According to the Realtek propritary driver and the rtw88 driver, the
tx rates of the ack (includes block ack) are initialized with lower
tx rates (no HT rates) which is set by the RRSR register value. In
real cases, ack rate higher than current tx rate could lead to
difficulty for the receiving end to receive management/control frames.
The retransmission rate would be higher then expected when the driver
is acting as receiver and the RSSI is not good.
Cross out higer rates for ack packet before implementing dynamic rrsr
configuration like the commit 4830872685f8 ("rtw88: add dynamic rrsr
configuration").
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001040044.1028708-1-chris.chiu@canonical.com
|
|
The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
|
|
The usage of fw_crash debugfs is to write 1 to it to trigger fw crash
simulation and to read from it to check the state. When zero is read,
it is supposed to mean fw crash/restart process is done. Then, some
test plans can be designed for crash/restart.
e.g.
step 1. trigger fw crash simulation
step 2. poll the state until zero is read
step 3. check connection by ping test
However, in certain connection cases, triggering fw crash simulation
will take a while. If the state is queried too early before restart
begins processing, it may mistakenly think restart process has been
done. If some tests are started at this time, something unexpected
might happen due to the follow-up restart process.
To avoid that, let fw_crash also show non-zero when a simulation
is still triggering.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001082301.4805-1-pkshih@realtek.com
|
