| Age | Commit message (Collapse) | Author |
|---|
|
The "priv->hw_type" is an enum and in this context GCC will treat it
as an unsigned int so the error handling will never trigger.
Fixes: a910e4a94f69 ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The module parameter rtw_fw_support_lps is misleading. It
is not used to represent the firmware's property, but to
determine if driver wants to ask firmware to enter LPS.
However, driver should better enable/disable PS through
cfg80211_ops::set_power_mgmt instead.
For example, one could use iw command to set PS state.
$ sudo iw wlanX set power_save [on/off]
So rtw_fw_support_lps should be removed because it is
misleading and useless. Instead of checking the parameter,
set PS mode according to IEEE80211_CONF_PS.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Compare with LCLK mode, PG mode saves more power, by turning
off more circuits. Therefore, to recover from PG mode, driver
needs to backup some information into rsvd page. Such as CAM
entries, DPK results.
As CAM entries can change, it is required to re-download CAM
entries after set_key.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add a module parameter to select deep PS mode. And the mode
cannot be changed after the module has been inserted and probed.
If anyone wants to change the deep mode, should change the mode
and probe the device again to setup the changed deep mode.
When the device is probed, driver will check the deep PS mode
with different IC's PS mode suppotability. If none of the
PS mode is matched, the deep PS mode is changed to NONE,
means deep PS is disabled.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sometimes LPS is not compatible with COEX's strategy, and
COEX will not allow driver to enter it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Deep power save allows firmware/hardware to operate in a
lower power state. And the deep power save mode depends on
LPS mode. So, before entering deep PS, driver must first
enter LPS mode.
Under Deep PS, most of hardware functions are shutdown,
driver will not be able to read/write registers and transfer
data to the device. Hence TX path must be protected by each
interface. Take PCI for example, DMA engine should be idle,
and no nore activities on the PCI bus.
If driver wants to operate on the device, such as register
read/write, it must first acquire the mutex lock and wake
up from Deep PS, otherwise the behavior is undefined.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Dynamic mechanism requires BB/RF working to adjust
hardware settings. But PS state periodically turns
off BB/RF, could lead to wrong setting.
So leave PS state before DM to make sure it works.
And then check if we can enter PS state again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Protect LPS enter/leave routine with rtwdev->mutex.
This helps to synchronize with driver's states correctly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is no more used, remove it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The original design of LPS enter/leave routines allows
to control the LPS state by each interface. But the
hardware cannot actually handle it that way. This means
the hardware can only enter LPS once with an associated
port, so there is no need to keep tracking the state of
each vif.
Hence the logic of enter/leave LPS state can be simple,
just to check the state of the device's flag. And for
leaving LPS state, it will get the same port id to send
to inform the hardware.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove PS related *_irqsafe functions to avoid entering/leaving PS
under interrupt context. Instead, make PS decision in watch_dog.
This could simplify the logic and make the code look clean.
But it could have a little side-effect that if the driver is having
heavy traffic before the every-2-second watch_dog detect the traffic
and decide to leave PS, the thoughput will be lower. Once traffic is
detected by watch_dog and left PS state, the throughput will resume
to the peak the hardware ought to have again.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If the driver doesn't reset the host's and device's indexes
in a single write, the indexes will become different in a
short period. And it will confuse the DMA engine, make it
start to process non-existed entries.
Better to Write-1-to-reset the indexes, for the DMA engine
to know that this is a reset of the H2C queue, not a kick
off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These helper functions seems useless. And in some cases
we want to use test_and_[set/clear]_bit, these helpers
will make the code more complicated. So remove them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2255:7: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function rtl8723be_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2254:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit a619d1abe20c ("rtlwifi:
rtl8723be: Add new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2805:34: warning: variable reg_ecc set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c: In function rtl92ee_phy_iq_calibrate:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/phy.c:2804:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable]
They are not used since commit b1a3bfc97cd9 ("rtlwifi:
rtl8192ee: Move driver from staging to the regular tree")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:656:5: warning: variable short_gi set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c: In function rtl92ee_tx_fill_desc:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:648:15: warning: variable buf_len set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338bf ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_pg_packet_write:
drivers/net/wireless/realtek/rtlwifi/efuse.c:937:24: warning: variable dataempty set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/efuse.c: In function efuse_get_current_size:
drivers/net/wireless/realtek/rtlwifi/efuse.c:1202:5: warning: variable hoffset set but not used [-Wunused-but-set-variable]
They are not used since commit f1d2b4d338bf ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/ps.c: In function rtl_ps_set_rf_state:
drivers/net/wireless/realtek/rtlwifi/ps.c:71:19: warning: variable rtstate set but not used [-Wunused-but-set-variable]
It is not used since commit f1d2b4d338bf ("rtlwifi:
rtl818x: Move drivers into new realtek directory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
commit 174e23810cd31
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
This patch ports 2 patches from ath9k to ath9k_htc.
commit 3c0efb745a172bfe96459e20cbd37b0c945d5f8d "ath9k: discard
undersized packets".
commit df5c4150501ee7e86383be88f6490d970adcf157 "ath9k: correctly
handle short radar pulses".
[ 112.835889] ------------[ cut here ]------------
[ 112.835971] WARNING: CPU: 5 PID: 0 at net/mac80211/rx.c:804 ieee80211_rx_napi+0xaac/0xb40 [mac80211]
[ 112.835973] Modules linked in: ath9k_htc ath9k_common ath9k_hw ath mac80211 cfg80211 libarc4 nouveau snd_hda_codec_hdmi intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_hda_codec video snd_hda_core ttm snd_hwdep drm_kms_helper snd_pcm crct10dif_pclmul snd_seq_midi drm snd_seq_midi_event crc32_pclmul snd_rawmidi ghash_clmulni_intel snd_seq aesni_intel aes_x86_64 crypto_simd cryptd snd_seq_device glue_helper snd_timer sch_fq_codel i2c_algo_bit fb_sys_fops snd input_leds syscopyarea sysfillrect sysimgblt intel_cstate mei_me intel_rapl_perf soundcore mxm_wmi lpc_ich mei kvm_intel kvm mac_hid irqbypass parport_pc ppdev lp parport ip_tables x_tables autofs4 hid_generic usbhid hid raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear e1000e ahci libahci wmi
[ 112.836022] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.3.0-wt #1
[ 112.836023] Hardware name: MouseComputer Co.,Ltd. X99-S01/X99-S01, BIOS 1.0C-W7 04/01/2015
[ 112.836056] RIP: 0010:ieee80211_rx_napi+0xaac/0xb40 [mac80211]
[ 112.836059] Code: 00 00 66 41 89 86 b0 00 00 00 e9 c8 fa ff ff 4c 89 b5 40 ff ff ff 49 89 c6 e9 c9 fa ff ff 48 c7 c7 e0 a2 a5 c0 e8 47 41 b0 e9 <0f> 0b 48 89 df e8 5a 94 2d ea e9 02 f9 ff ff 41 39 c1 44 89 85 60
[ 112.836060] RSP: 0018:ffffaa6180220da8 EFLAGS: 00010286
[ 112.836062] RAX: 0000000000000024 RBX: ffff909a20eeda00 RCX: 0000000000000000
[ 112.836064] RDX: 0000000000000000 RSI: ffff909a2f957448 RDI: ffff909a2f957448
[ 112.836065] RBP: ffffaa6180220e78 R08: 00000000000006e9 R09: 0000000000000004
[ 112.836066] R10: 000000000000000a R11: 0000000000000001 R12: 0000000000000000
[ 112.836068] R13: ffff909a261a47a0 R14: 0000000000000000 R15: 0000000000000004
[ 112.836070] FS: 0000000000000000(0000) GS:ffff909a2f940000(0000) knlGS:0000000000000000
[ 112.836071] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 112.836073] CR2: 00007f4e3ffffa08 CR3: 00000001afc0a006 CR4: 00000000001606e0
[ 112.836074] Call Trace:
[ 112.836076] <IRQ>
[ 112.836083] ? finish_td+0xb3/0xf0
[ 112.836092] ? ath9k_rx_prepare.isra.11+0x22f/0x2a0 [ath9k_htc]
[ 112.836099] ath9k_rx_tasklet+0x10b/0x1d0 [ath9k_htc]
[ 112.836105] tasklet_action_common.isra.22+0x63/0x110
[ 112.836108] tasklet_action+0x22/0x30
[ 112.836115] __do_softirq+0xe4/0x2da
[ 112.836118] irq_exit+0xae/0xb0
[ 112.836121] do_IRQ+0x86/0xe0
[ 112.836125] common_interrupt+0xf/0xf
[ 112.836126] </IRQ>
[ 112.836130] RIP: 0010:cpuidle_enter_state+0xa9/0x440
[ 112.836133] Code: 3d bc 20 38 55 e8 f7 1d 84 ff 49 89 c7 0f 1f 44 00 00 31 ff e8 28 29 84 ff 80 7d d3 00 0f 85 e6 01 00 00 fb 66 0f 1f 44 00 00 <45> 85 ed 0f 89 ff 01 00 00 41 c7 44 24 10 00 00 00 00 48 83 c4 18
[ 112.836134] RSP: 0018:ffffaa61800e3e48 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
[ 112.836136] RAX: ffff909a2f96b340 RBX: ffffffffabb58200 RCX: 000000000000001f
[ 112.836137] RDX: 0000001a458adc5d RSI: 0000000026c9b581 RDI: 0000000000000000
[ 112.836139] RBP: ffffaa61800e3e88 R08: 0000000000000002 R09: 000000000002abc0
[ 112.836140] R10: ffffaa61800e3e18 R11: 000000000000002d R12: ffffca617fb40b00
[ 112.836141] R13: 0000000000000002 R14: ffffffffabb582d8 R15: 0000001a458adc5d
[ 112.836145] ? cpuidle_enter_state+0x98/0x440
[ 112.836149] ? menu_select+0x370/0x600
[ 112.836151] cpuidle_enter+0x2e/0x40
[ 112.836154] call_cpuidle+0x23/0x40
[ 112.836156] do_idle+0x204/0x280
[ 112.836159] cpu_startup_entry+0x1d/0x20
[ 112.836164] start_secondary+0x167/0x1c0
[ 112.836169] secondary_startup_64+0xa4/0xb0
[ 112.836173] ---[ end trace 9f4cd18479cc5ae5 ]---
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
rs_datalen is be16 so we need to convert it before printing.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently, data variable in ar9003_hw_thermo_cal_apply() could be
uninitialized if ar9300_otp_read_word() will fail to read the value.
Initialize data variable with 0 to prevent an undefined behavior. This
will be enough to handle error case when ar9300_otp_read_word() fails.
Fixes: 80fe43f2bbd5 ("ath9k_hw: Read and configure thermocal for AR9462")
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The IRAM start address in coredump was wrong for QCA9984, QCA4019, QCA9888 and
QCA99x0.
Tested on: QCA9984, QCA4019
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Software version within WMI event ready message was displayed
in a not very useful decimal format. Change this info to be shown
in a hexadecimal format instead.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Displays lowest/highest supported channels for both 2ghz and 5ghz
bands as they're fetched within WMI service ready event.
These are shown in a frequency format.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is clearer than copy/pasting the magic number '+ 2' around, and it
even saves the need for one existing comment.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There is no need to check "rtlhal->interface == INTF_PCI" twice in
_rtl_ps_inactive_ps(). The nested check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
'rtstatus' local variable is not used,
so remove it for clean-up.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix bbp ready check in mt7601u_wait_bbp_ready. The issue is reported by
coverity with the following error:
Logical vs. bitwise operator
The expression's value does not depend on the operands; inadvertent use
of the wrong operator is a likely logic error.
Addresses-Coverity-ID: 1309441 ("Logical vs. bitwise operator")
Fixes: c869f77d6abb ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In rsi_send_beacon, if rsi_prepare_beacon fails the allocated skb should
be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
drivers/net/wireless/realtek/rtw88/rtw8822c.c:2606:9-10: WARNING: return
of 0/1 in function 'rtw8822c_dpk_coef_iq_check' with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 5227c2ee453d ("rtw88: 8822c: add SW DPK support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The nested 'li_mimo == &locale_bn' check is excessive and always
true. Thus it can be safely removed.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
'pih' is known to be non-NULL at this point, so the test can be removed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff372 ("wil6210: add wil_netif_rx() helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
