| Age | Commit message (Collapse) | Author |
|---|
|
Rather than using a static array, use a hlist to store the muxed
endpoints and use the mux id to query the rmnet_device.
This is useful as usually very few mux ids are used.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rmnet_devices information is already stored in muxed_ep, so
storing this in rmnet_devices[] again is redundant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The end point is set twice in the local_ep as well as the mux_id and
the real_dev in the rmnet private structure. Remove the local_ep.
While these elements are equivalent, rmnet_endpoint will be
used only as part of the rmnet_port for muxed scenarios in VND mode.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mode information on the real device makes it easier to route packets
to rmnet device or bridged device based on the configuration.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of these constants were used in the initial patchset where
custom netlink configuration was used and hence are no longer relevant.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be rewritten in the following patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the error messages that are printed by the interrupt handlers
are poorly written. For example, many don't include a device prefix,
so there's no indication that they are EMAC errors.
Also use rate limiting for all messages that could be printed from
interrupt context.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC has a restriction that the upper 32 bits of the base addresses
for the RFD and RRD rings must be the same. The ensure that restriction,
we allocate twice the space for the RRD and locate it at an appropriate
address.
We also re-arrange the allocations so that invalid addresses are even
less likely.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EMAC is capable of multiple TX and RX rings, but the driver only
supports one ring for each. One function had some left-over unused
code that supports multiple rings, but all it did was make the code
harder to read.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 64/32-bit DMA mask hackery in the EMAC driver is not actually necessary,
and is technically not accurate. The EMAC hardware is limted to a 45-bit
DMA address. Although no EMAC-enabled system can have that much DDR,
an IOMMU could possible provide a larger address. Rather than play games
with the DMA mappings, the driver should provide a correct value and
trust the DMA/IOMMU layers to do the right thing.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl_init_one() currently enables PCI wakeups if the ethernet device
is found to be WOL-capable. There is no need to do this when
rtl8169_set_wol() will correctly enable or disable the same wakeup flag
when WOL is activated/deactivated.
This works around an ACPI DSDT bug which prevents the Acer laptop models
Aspire ES1-533, Aspire ES1-732, PackardBell ENTE69AP and Gateway NE533
from entering S3 suspend - even when no ethernet cable is connected.
On these platforms, the DSDT says that GPE08 is a wakeup source for
ethernet, but this GPE fires as soon as the system goes into suspend,
waking the system up immediately. Having the wakeup normally disabled
avoids this issue in the default case.
With this change, WOL will continue to be unusable on these platforms
(it will instantly wake up if WOL is later enabled by the user) but we
do not expect this to be a commonly used feature on these consumer
laptops. We have separately determined that WOL works fine without any
ACPI GPEs enabled during sleep, so a DSDT fix or override would be
possible to make WOL work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warnings:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_ethtool.c:464:5: warning:
symbol 'hns3_change_all_ring_bd_num' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_ethtool.c:477:5: warning:
symbol 'hns3_set_ringparam' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the return error code to EINVAL if the MAC
address is not valid in the set_wol function.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the TI DP83822 10/100Mbit ethernet phy.
The DP83822 provides flexibility to connect to a MAC through a
standard MII, RMII or RGMII interface.
In addition the DP83822 needs to be removed from the DP83848 driver
as the WoL support is added here for this device.
Datasheet:
http://www.ti.com/product/DP83822I/datasheet
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: cda7ea690350 ("macsec: check return value of skb_to_sgvec always")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When both user ports are joined to the same bridge, the normal
HW MAC learning is enabled. This means that unicast traffic is forwarded
in HW.
If one of the user ports leave the bridge,
the ports goes back to the initial separated operation.
Port separation relies on disabled HW MAC learning. Hence the condition
that both ports must join same bridge.
Add brigde methods port_bridge_join, port_bridge_leave and
port_stp_state_set.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for next patch:
Move tag setup from lan9303_separate_ports() to new function
lan9303_setup_tagging()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Work continues in various areas:
* port authorized event for 4-way-HS offload (Avi)
* enable MFP optional for such devices (Emmanuel)
* Kees's timer setup patch for mac80211 mesh
(the part that isn't trivially scripted)
* improve VLAN vs. TXQ handling (myself)
* load regulatory database as firmware file (myself)
* with various other small improvements and cleanups
I merged net-next once in the meantime to allow Kees's
timer setup patch to go in.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi patches for 4.15 (v2)
* Cleanups: - remove an unused value that we read from the NVM;
- remove link quality measurement code that was never used;
* One FW command API update;
* A fix and an addition for PCI devices for the A000 family;
* Tiny refactor of ref/unref code used by runtime-PM;
* Some debugging improvements;
* Implementation of a more flexible way to define command queue sizes;
* ACPI code refactoring;
* Some coding-style fixes;
* Avoid redundant command to the firmware;
* Add a struct with the format of one FW command;
* Change an error log to a warning when the FW API is not aligned with
the driver (important during development);
* Change a WARN_ON to WARN_ONCE to make it more descriptive and less
noisy (i.e. no repeated warnings on a firmware triggered error);
* Dump PCI registers when an error occurs, to make it easier to debug;
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-10
This series contains updates to e1000e and igb.
Benjamin Poirier provides several fixes for e1000e, starting with a
correction to the return status which was always returning success even
if it was not successful. Fixed code comments to reflect the actual
code behavior. Fixed the conditional test for the correct return
value. Fixed a potential race condition reported by Lennart Sorensen,
where the single flag get_link_status is used to signal two different
states.
Sasha fixes a buffer overrun for i219 devices, where the chipset had
reduced the round-trip latency for the LAN controller DMA accesses
which in some high performance cases caused a buffer overrun while
processing the DMA transactions.
Willem de Bruijn changes the default behavior of e1000e to use the
burst mode settings by default unless the user specifies the
receive interrupt delay (RxIntDelay).
Florian Fainelli updates the driver to differentiate between when
e1000e_put_txbuf() is called from normal reclamation or when a
DMA mapping failure to make the driver more "drop monitor friendly".
Christophe JAILLET fixes a potential NULL pointer dereference by
properly returning -ENOMEM on memory allocation failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
page_address() does not handle NULL argument gracefully,
make sure we NULL-check the page pointer before passing it
to page_address().
Fixes: ecd63a0217d5 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The while loop fetching 64 bit ethtool statistics may have
to retry multiple times, it shouldn't modify the outside state.
Fixes: 4c3523623dc0 ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-10
This series contains updates to i40e only.
Stefano Brivio fixes the grammar in a function header comment.
Alex fixes a memory leak where we were not correctly placing the pages
from buffers that had been used to return a filter programming status
back on the ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove limitation of netif_get_num_default_rss_queues()
from logic of RX rings default number.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Limit the number of RX rings by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Limit the number of TX rings per UP by the number of cores
in the system.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix the ring count for ETHTOOL_GRXRINGS. Ring count
not TC size should be return for command "ethtool -n ethx".
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for ethtool's ETHTOOL_GRXFH in hns3_get_rxnfc().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports the ethtool's set_rxnfc().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports the ethtool's set_ringparam().
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the ring index in hns3_fini_ring.
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 0x50aa and 0x50ab T5 device id's.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for new flash parts identification, and
also cleanup the flash Part identifying and decoding
code.
Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert Variable Length Array in Struct (VLAIS) to valid C by converting
local struct definition to use a flexible array. The structure is only
used to define a cast of a buffer so the size of the struct is not used
to allocate storage.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mark Charebois <charlebm@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
e1000e_put_txbuf() can be called from normal reclamation path as well as
when a DMA mapping failure, so we need to differentiate these two cases
when freeing SKBs to be drop monitor friendly. e1000e_tx_hwtstamp_work()
and e1000_remove() are processing TX timestamped SKBs and those should
not be accounted as drops either.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.
The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.
Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc33
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68e5 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reading e1000e_check_for_copper_link() shows that get_link_status is set to
false after link has been detected. Therefore, it stays TRUE until then.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7ccbf ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d94 ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Driver will advertise RANDOM_MAC support only if the device
supports this feature.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
My static checker complains that we have an upper bound but no lower
bound. I suspect neither are really required but it doesn't hurt to add
a check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ieee80211_register_hw() in p54_register_common() may fail and leds won't
get initialized. Currently p54_unregister_common() doesn't check that and
always calls p54_unregister_leds(). The fix is to check priv->registered
flag before calling p54_unregister_leds().
Found by syzkaller.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1404 Comm: kworker/1:1 Not tainted
4.14.0-rc1-42251-gebb2c2437d80-dirty #205
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
register_lock_class+0x6c4/0x1a00 kernel/locking/lockdep.c:769
__lock_acquire+0x27e/0x4550 kernel/locking/lockdep.c:3385
lock_acquire+0x259/0x620 kernel/locking/lockdep.c:4002
flush_work+0xf0/0x8c0 kernel/workqueue.c:2886
__cancel_work_timer+0x51d/0x870 kernel/workqueue.c:2961
cancel_delayed_work_sync+0x1f/0x30 kernel/workqueue.c:3081
p54_unregister_leds+0x6c/0xc0 drivers/net/wireless/intersil/p54/led.c:160
p54_unregister_common+0x3d/0xb0 drivers/net/wireless/intersil/p54/main.c:856
p54u_disconnect+0x86/0x120 drivers/net/wireless/intersil/p54/p54usb.c:1073
usb_unbind_interface+0x21c/0xa90 drivers/usb/core/driver.c:423
__device_release_driver drivers/base/dd.c:861
device_release_driver_internal+0x4f4/0x5c0 drivers/base/dd.c:893
device_release_driver+0x1e/0x30 drivers/base/dd.c:918
bus_remove_device+0x2f4/0x4b0 drivers/base/bus.c:565
device_del+0x5c4/0xab0 drivers/base/core.c:1985
usb_disable_device+0x1e9/0x680 drivers/usb/core/message.c:1170
usb_disconnect+0x260/0x7a0 drivers/usb/core/hub.c:2124
hub_port_connect drivers/usb/core/hub.c:4754
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x1318/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
process_scheduled_works kernel/workqueue.c:2179
worker_thread+0xb2b/0x1850 kernel/workqueue.c:2255
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
