| Age | Commit message (Collapse) | Author |
|---|
|
The value is already the calculation so remove the log prefix.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1f515486275a08a17a2c806b844cca18f7de5b34.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As noted in commit 28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function page_shift() is supported after the commit 94ad9338109f
("mm: introduce page_shift()").
So replace with page_shift() in ehea_is_hugepage() for readability.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds support for xmit_more based on the igb commit 6f19e12f6230
("igb: flush when in xmit_more mode and under descriptor pressure") and
commit 6b16f9ee89b8 ("net: move skb->xmit_more hint to softnet data") that
were made to igb to support this feature. The function netif_xmit_stopped
is called to check whether transmit queue on device is currently unable to
send to determine whether we must write the tail because we can add no
further buffers.
When normal packets and/or xmit_more packets fill up tx_desc, it is
necessary to trigger NIC tx reg.
Following the advice from David Miller and Jakub Kicinski, after the
xmit_more feature is added, the following scenario will occur.
|
xmit_more packets
|
DMA_MAPPING
|
DMA_MAPPING error check
|
xmit_more packets already in HW xmit queue
|
In the above scenario, if DMA_MAPPING error occurrs, the xmit_more packets
already in HW xmit queue will also be dropped. This is different from the
behavior before xmit_more feature. So it is necessary to trigger NIC HW tx
reg in the above scenario.
To the non-xmit_more packets, the above scenario will not occur.
Tested:
- pktgen (xmit_more packets) SMP x86_64 ->
Test command:
./pktgen_sample03_burst_single_flow.sh ... -b 8 -n 1000000
Test results:
Params:
...
burst: 8
...
Result: OK: 12194004(c12188996+d5007) usec, 1000001 (1500byte,0frags)
82007pps 984Mb/sec (984084000bps) errors: 0
- iperf (normal packets) SMP x86_64 ->
Test command:
Server: iperf -s
Client: iperf -c serverip
Result:
TCP window size: 85.0 KByte (default)
------------------------------------------------------------
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 1.10 GBytes 942 Mbits/sec
CC: Joe Jin <joe.jin@oracle.com>
CC: JUNXIAO_BI <junxiao.bi@oracle.com>
Reported-and-tested-by: Nan san <nan.1986san@gmail.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like the port adding loop makes a re-appearance on net-next
after net was merged back into it (even though it doesn't feature
in the merge diff).
The ports are already added in nsim_dev_create() so when we try
to add them again get EEXIST, and see:
netdevsim: probe of netdevsim0 failed with error -17
in the logs. When we remove the loop again the nsim_dev_probe()
and nsim_dev_remove() become a wrapper of nsim_dev_create() and
nsim_dev_destroy(). Remove this layer of indirection.
Fixes: d31e95585ca6 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.
The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.
Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.
BugLink: https://bugs.launchpad.net/bugs/1827961
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.
Fixes: d1f0b5dce8fd ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a phy_interface_t to of_get_phy_mode(), by changing the type of
phy_mode in the device structure. This then requires that
zmii_attach() is also changes, since it takes a pointer to phy_mode.
Fixes: 0c65b2b90d13 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers to set/get the ATU statistics register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used. I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reason for the pre-allocation of one CQE is to enable resizing of
the CQ.
Fix comment accordingly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since de77ecd4ef02 ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since RSS hash is available from the host, record it in
the skb.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains updates to the ice driver only.
Anirudh refactors the code to reduce the kernel configuration flags and
introduces ice_base.c file.
Maciej does additional refactoring on the configuring of transmit
rings so that we are not configuring per each traffic class flow.
Added support for XDP in the ice driver. Provides additional
re-organizing of the code in preparation for adding build_skb() support
in the driver. Adjusted the computational padding logic for headroom
and tailroom to better support build_skb(), which also aligns with the
logic in other Intel LAN drivers. Added build_skb support and make use
of the XDP's data_meta.
Krzysztof refactors the driver to prepare for AF_XDP support in the
driver and then adds support for AF_XDP.
v2: Updated patch 3 of the series based on community feedback with the
following changes...
- return -EOPNOTSUPP instead of ENOTSUPP for too large MTU which makes
it impossible to attach XDP prog
- don't check for case when there's no XDP prog currently on interface
and ice_xdp() is called with NULL bpf_prog; this happens when user
does "ip link set eth0 xdp off" and no prog is present on VSI; no need
for that as it is handled by higher layer
- drop the extack message for unknown xdp->command
- use the smp_processor_id() for accessing the XDP Tx ring for XDP_TX
action
- don't leave the interface in downed state in case of any failure
during the XDP Tx resources handling
- undo rename of ice_build_ctob
The above changes caused a ripple effect in patches 4 & 5 to update
references to ice_build_ctob() which are now build_ctob()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains old Halloween candy updates, yet still sweet, to
fm10k, ixgbe and i40e.
Jake adds the missing initializers for a couple of the TLV attribute
macros. Added support for capturing and reporting statistics for all of
the VFs in a given PF. Lastly, bump the version of the fm10k driver to
reflect the recent changes.
Alex addresses locality issues in the ixgbe driver when it is loaded on
a system supporting multiple NUMA nodes.
Manjunath Patil provides changes to the ixgbe driver, similar to those
made to igb, to prevent transmit packets to request a hardware timestamp
when the NIC has not been setup via the SIOCSHWTSTAMP ioctl.
Alice adds support for x710 by adding the missing device id's in the
appropriate places to ensure all the features are enabled in i40e.
Jesse adds support for VF stats gathering in the i40e via the kernel
via ndo_get_vf_stats function.
v2: Fixed up commit id references in patch 5's description to align with
how commit id's should be referenced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
condition
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>
Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
RX: bytes packets mcast bcast
128000 1000 104 104
TX: bytes packets
128000 1000
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places. Adding it
to enable it's use.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Similar-to:
commit 26bd4e2db06b ("igb: protect TX timestamping from API misuse")
commit 0a6f2f05a2f5 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.
The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.
In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.
I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.
Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.
In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.
This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;
With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.
In the followup patch the headroom/tailroom computation logic will be
introduced.
This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
