summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2018-03-19i40e: Fix incorrect return typesDoug Dziggel
Fix return types from i40e_status to enum i40e_status_code. Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19i40e: add doxygen comment for new mode parameterJacob Keller
A recent patch updated the signature for i40e_aq_set_switch_config() to add a new parameter 'mode'. It forgot to document the parameter in the doxygen function header comment. Add the parameter to the function description now. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19i40e: Close client on suspend and restore client MSIx on resumeShiraz Saleem
During suspend client MSIx vectors are freed while they are still in use causing a crash on entering S3. Fix this calling client close before freeing up its MSIx vectors. Also update the client MSIx vectors on resume before client open is called. Fixes commit b980c0634fe5 ("i40e: shutdown all IRQs and disable MSI-X when suspended") Reported-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19i40e: Prevent setting link speed on KX_X722Patryk Małek
Setting link settings on backplane devices shouldn't be allowed. This patch adds one more device id to the list which we check that against. Signed-off-by: Patryk Małek <patryk.malek@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19i40e: Properly check allowed advertisement capabilitiesJan Sokolowski
The i40e_set_link_ksettings and i40e_get_link_ksettings use different codepaths to check available and supported advertisement modes. This creates scenarios where it's possible to set a mode that's not allowed, resulting in a link down. Fix setting advertisement in i40e_set_link_ksettings by calling i40e_get_link_ksettings to check what modes are allowed. Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19i40evf: Reorder configure_clsflower to avoid deadlock on errorAlexander Duyck
While doing some code review I noticed that we can get into a state where we exit with the "IN_CRITICAL_TASK" bit set while notifying the PF of flower filters. This patch is meant to address that plus tweak the ordering of the while loop waiting on it slightly so that we don't wait an extra period after we have failed for the last time. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-03-19can: cc770: Fix use after free in cc770_tx_interrupt()Andri Yngvason
This fixes use after free introduced by the last cc770 patch. Signed-off-by: Andri Yngvason <andri.yngvason@marel.com> Fixes: 746201235b3f ("can: cc770: Fix queue stall & dropped RTR reply") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-19iwlwifi: mvm: Move unused phy's to a default channelAndrei Otcheretianski
When immediate quiet bit is set in CSA, the entire channel is blocked by the firmware. It is expected that all the MACs will evacuate the channel and the phy will be eventually either moved or removed. Currently, the phy context is just unreferenced and thus, the quiet bit is kept set and it will be impossible to TX on this phy, if we will need to reuse it in the future. This can be seen when doing a channel switch with mode=1 (quiet) twice from channel X to Y and then back to channel X. Fix that, by moving the phy context to a default channel when not referenced anymore. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-19iwlwifi: mvm: fix array out of bounds referenceAvraham Stern
When starting aggregation, the code checks the status of the queue allocated to the aggregation tid, which might not yet be allocated and thus the queue index may be invalid. Fix this by reserving a new queue in case the queue id is invalid. While at it, clean up some unreachable code (a condition that is already handled earlier) and remove all the non-DQA comments since non-DQA mode is no longer supported. Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue") Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-19iwlwifi: mvm: make sure internal station has a valid idAvraham Stern
If the driver failed to resume from D3, it is possible that it has no valid aux station. In such case, fw restart will end up in sending station related commands with an invalid station id, which will result in an assert. Fix this by allocating a new station id for the aux station if it does not have a valid id even in the case of fw restart. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-19iwlwifi: mvm: clear tx queue id when unreserving aggregation queueAvraham Stern
When a queue is reserved for aggregation, the queue id is assigned to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper() takes care of allocating the queue before actual tx starts. When the reservation is cancelled (e.g. when the AP declined the aggregation request) the tid_data is not cleared. As a result, following tx for this tid was trying to use an unallocated queue. Fix this by setting the txq_id for the tid to invalid when unreserving the queue. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-19iwlwifi: mvm: Increase session protection time after CSAndrei Otcheretianski
After switching to a new channel, driver schedules session protection time event in order to hear the beacon on the new channel. The duration of the protection is two beacon intervals. However, since we start to switch slightly before beacon with count 1, in case we don't hear (or AP doesn't transmit) the very first beacon on the new channel the protection ends without hearing any beacon at all. At this stage the switch is not complete, the queues are closed and the interface doesn't have quota yet or TBTT events. As the result, we are stuck forever waiting for iwl_mvm_post_channel_switch() to be called. Fix this by increasing the protection time to be 3 beacon intervals and in addition drop the connection if the time event ends before we got any beacon. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-18net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYsAndrew Lunn
When registering an MDIO bus, it is possible to pass an array of interrupts, one per address on the bus. phylib will then associate the interrupt to the PHY device, if no other interrupt is provided. Some of the global2 interrupts are PHY interrupts. Place them into the MDIO bus structure. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-18net: dsa: mv88e6xxx: Add number of internal PHYsAndrew Lunn
Add to the info structure the number of internal PHYs, if they generate interrupts. Some of the older generations of switches have internal PHYs, but no interrupt registers. In this case, set the count to zero. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-18net: dsa: mv88e6xxx: Add missing g1 IRQ numbersAndrew Lunn
With the recent change to polling for interrupts, it is important that the number of global 1 interrupts is listed. Without it, the driver requests an interrupt domain for zero interrupts, which returns EINVAL, and the probe fails. Add two missing entries. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-18net: dsa: mv88e6xxx: Fix missing register lock in serdes_get_statsFlorian Fainelli
We can hit the register lock not held assertion with the following path: [ 34.170631] mv88e6085 0.1:00: Switch registers lock not held! [ 34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143 [ 34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) [ 34.189519] Backtrace: [ 34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24) [ 34.199680] r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000 [ 34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28) [ 34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c) [ 34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c) [ 34.229257] r5:a09cd128 r4:9ee31d07 [ 34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64) [ 34.242690] r4:9f5dc010 [ 34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c) [ 34.255389] r4:00000001 [ 34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0) [ 34.268156] r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c [ 34.276052] r4:9f5dc010 [ 34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4) mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both chip->info->ops->stats_get_stats(), which holds the register lock, and chip->info->ops->serdes_get_stats() which does not. Have chip->info->ops->serdes_get_stats() be running with the register lock held to avoid such assertions. Fixes: 436fe17d273b ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-18net: fec: Fix unbalanced PM runtime callsFlorian Fainelli
When unbinding/removing the driver, we will run into the following warnings: [ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator [ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable! [ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 [ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1 [ 259.696239] libphy: fec_enet_mii_bus: probed Avoid these warnings by balancing the runtime PM calls during fec_drv_remove(). Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17net: dsa: mv88e6xxx: Fix IRQ when loading moduleAndrew Lunn
Handle polled interrupts correctly when loading the module. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 294d711ee8c0 ("net: dsa: mv88e6xxx: Poll when no interrupt defined") Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Remove unused TSO resources in TX pool structureThomas Falcon
Finally, remove the TSO-specific fields in the TX pool strcutures. These are no longer needed with the introduction of separate buffer pools for TSO transmissions. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Update TX pool cleaning routineThomas Falcon
Update routine that cleans up any outstanding transmits that have not received completions when the device needs to close. Introduces a helper function that cleans one TX pool to make code more readable. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Improve TX buffer accountingThomas Falcon
Improve TX pool buffer accounting to prevent the producer index from overruning the consumer. First, set the next free index to an invalid value if it is in use. If next buffer to be consumed is in use, drop the packet. Finally, if the transmit fails for some other reason, roll back the consumer index and set the free map entry to its original value. This should also be done if the DMA map fails. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Update TX and TX completion routinesThomas Falcon
Update TX and TX completion routines to account for TX pool restructuring. TX routine first chooses the pool depending on whether a packet is GSO or not, then uses it accordingly. For the completion routine to know which pool it needs to use, set the most significant bit of the correlator index to one if the packet uses the TSO pool. On completion, unset the bit and use the correlator index to release the buffer pool entry. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Update TX pool initialization routineThomas Falcon
Introduce function that initializes one TX pool. Use that to create each pool entry in both the standard TX pool and TSO pool arrays. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Update release TX pool routineThomas Falcon
Introduce function that frees one TX pool. Use that to release each pool in both the standard TX pool and TSO pool arrays. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Update and clean up reset TX pool routineThomas Falcon
Update TX pool reset routine to accommodate new TSO pool array. Introduce a function that resets one TX pool, and use that function to initialize each pool in both pool arrays. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17ibmvnic: Generalize TX pool structureThomas Falcon
Remove some unused fields in the structure and include values describing the individual buffer size and number of buffers in a TX pool. This allows us to use these fields for TX pool buffer accounting as opposed to using hard coded values. Include a new pool array for TSO transmissions. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17hv_netvsc: add trace pointsStephen Hemminger
This adds tracepoints to the driver which has proved useful in debugging startup and shutdown race conditions. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17hv_netvsc: pass netvsc_device to rndis haltStephen Hemminger
The caller has a valid pointer, pass it to rndis_filter_halt_device and avoid any possible RCU races here. Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17vmxnet3: use correct flag to indicate LRO featureRonak Doshi
'Commit 45dac1d6ea04 ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)")' introduced a flag "lro" in structure vmxnet3_adapter which is used to indicate whether LRO is enabled or not. However, the patch did not set the flag and hence it was never exercised. So, when LRO is enabled, it resulted in poor TCP performance due to delayed acks. This issue is seen with packets which are larger than the mss getting a delayed ack rather than an immediate ack, thus resulting in high latency. This patch removes the lro flag and directly uses device features against NETIF_F_LRO to check if lro is enabled. Fixes: 45dac1d6ea04 ("vmxnet3: Changes for vmxnet3 adapter version 2 (fwd)") Reported-by: Rachel Lunnon <rachel_lunnon@stormagic.com> Signed-off-by: Ronak Doshi <doshir@vmware.com> Acked-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17vmxnet3: avoid xmit reset due to a race in vmxnet3Ronak Doshi
The field txNumDeferred is used by the driver to keep track of the number of packets it has pushed to the emulation. The driver increments it on pushing the packet to the emulation and the emulation resets it to 0 at the end of the transmit. There is a possibility of a race either when (a) ESX is under heavy load or (b) workload inside VM is of low packet rate. This race results in xmit hangs when network coalescing is disabled. This change creates a local copy of txNumDeferred and uses it to perform ring arithmetic. Reported-by: Noriho Tanaka <ntanaka@vmware.com> Signed-off-by: Ronak Doshi <doshir@vmware.com> Acked-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17net: ethernet: ti: cpsw: enable vlan rx vlan offloadGrygorii Strashko
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in CPSW_CONTROL register. VLAN header encapsulation word has following format: HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7) HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit. HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is VLAN-tagged, priority-tagged, or non-tagged. 00: VLAN-tagged packet 01: Reserved 10: Priority-tagged packet 11: Non-tagged packet This feature can be used to implement TX VLAN offload in case of VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was received on port with PVID set. As per documentation, CPSW never modifies packet data on Host egress (RX) and as result, without this feature enabled, Host port will not be able to receive properly packets which entered switch non-tagged through external Port with PVID set (when non-tagged packet forwarded from external Port with PVID set to another external Port - packet will be VLAN tagged properly). Implementation details: - on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI descriptor to identify when VLAN header encapsulation word is present. - PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and pass packet as is; - if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass packet as is; - In dual mac mode traffic is separated between ports using default port vlans, which are not be visible to Host and so should not be reported. Hence, check for default port vlans in dual mac mode and ignore VLAN header encapsulation word; - otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag(); - PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17net: ethernet: ti: cpsw: add check for in-band mode setting with RGMII PHY ↵SZ Lin (林上智)
interface According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only available when PHY is configured in RGMII mode with 10Mbps speed. It will cause some networking issues without RGMII mode, such as carrier sense errors and low throughput. TI also mentioned this issue in their forum[4]. This patch adds the check mechanism for PHY interface with RGMII interface type, the in-band mode can only be set in RGMII mode with 10Mbps speed. References: [1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf [2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf [3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf [4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155 Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com> Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com> Signed-off-by: Schuyler Patton <spatton@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17net: hns: Fix ethtool private flagsMatthias Brugger
The driver implementation returns support for private flags, while no private flags are present. When asked for the number of private flags it returns the number of statistic flag names. Fix this by returning EOPNOTSUPP for not implemented ethtool flags. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17mlxsw: spectrum_buffers: Set a minimum quota for CPU port trafficIdo Schimmel
In commit 9ffcc3725f09 ("mlxsw: spectrum: Allow packets to be trapped from any PG") I fixed a problem where packets could not be trapped to the CPU due to exceeded shared buffer quotas. The mentioned commit explains the problem in detail. The problem was fixed by assigning a minimum quota for the CPU port and the traffic class used for scheduling traffic to the CPU. However, commit 117b0dad2d54 ("mlxsw: Create a different trap group list for each device") assigned different traffic classes to different packet types and rendered the fix useless. Fix the problem by assigning a minimum quota for the CPU port and all the traffic classes that are currently in use. Fixes: 117b0dad2d54 ("mlxsw: Create a different trap group list for each device") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Eddie Shklaer <eddies@mellanox.com> Tested-by: Eddie Shklaer <eddies@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-17cxgb4: Fix queue free path of ULD driversArjun Vynipadath
Setting sge_uld_rxq_info to NULL in free_queues_uld(). We are referencing sge_uld_rxq_info in cxgb_up(). This will fix a panic when interface is brought up after a ULDq creation failure. Fixes: 94cdb8bb993a (cxgb4: Add support for dynamic allocation of resources for ULD) Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Ganesh Goudhar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16liquidio: Simplified napi pollIntiyaz Basha
1) Moved interrupt enable related code from octeon_process_droq_poll_cmd() to separate function octeon_enable_irq(). 2) Removed wrapper function octeon_process_droq_poll_cmd(), and directlyi using octeon_droq_process_poll_pkts(). 3) Removed unused macros POLL_EVENT_XXX. Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16cxgb4: notify fatal error to uld driversGanesh Goudar
notify uld drivers if the adapter encounters fatal error. Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16qede: Fix qedr link updateMichal Kalderon
Link updates were not reported to qedr correctly. Leading to cases where a link could be down, but qedr would see it as up. In addition, once qede was loaded, link state would be up, regardless of the actual link state. Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16qed: Fix non TCP packets should be dropped on iWARP ll2 connectionMichal Kalderon
FW workaround. The iWARP LL2 connection did not expect TCP packets to arrive on it's connection. The fix drops any non-tcp packets Fixes b5c29ca ("qed: iWARP CM - setup a ll2 connection for handling SYN packets") Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16qed: Fix MPA unalign flow in case header is split across two packets.Michal Kalderon
There is a corner case in the MPA unalign flow where a FPDU header is split over two tcp segments. The length of the first fragment in this case was not initialized properly and should be '1' Fixes: c7d1d839 ("qed: Add support for MPA header being split over two tcp packets") Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16net: systemport: Rewrite __bcm_sysport_tx_reclaim()Florian Fainelli
There is no need for complex checking between the last consumed index and current consumed index, a simple subtraction will do. This also eliminates the possibility of a permanent transmit queue stall under the following conditions: - one CPU bursts ring->size worth of traffic (up to 256 buffers), to the point where we run out of free descriptors, so we stop the transmit queue at the end of bcm_sysport_xmit() - because of our locking, we have the transmit process disable interrupts which means we can be blocking the TX reclamation process - when TX reclamation finally runs, we will be computing the difference between ring->c_index (last consumed index by SW) and what the HW reports through its register - this register is masked with (ring->size - 1) = 0xff, which will lead to stripping the upper bits of the index (register is 16-bits wide) - we will be computing last_tx_cn as 0, which means there is no work to be done, and we never wake-up the transmit queue, leaving it permanently disabled A practical example is e.g: ring->c_index aka last_c_index = 12, we pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12, so last_tx_cn == 0, nothing happens. Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16net: macb: Add phy-handle DT supportBrad Mouring
This optional binding (as described in the ethernet DT bindings doc) directs the netdev to the phydev to use. This is useful for a phy chip that has >1 phy in it, and two netdevs are using the same phy chip (i.e. the second mac's phy lives on the first mac's MDIO bus) The devicetree snippet would look something like this: ethernet@feedf00d { ... phy-handle = <&phy0> // the first netdev is physically wired to phy0 ... phy0: phy@0 { ... reg = <0x0> // MDIO address 0 ... } phy1: phy@1 { ... reg = <0x1> // MDIO address 1 ... } ... } ethernet@deadbeef { ... phy-handle = <&phy1> // tells the driver to use phy1 on the // first mac's mdio bus (it's wired thusly) ... } The work done to add the phy_node in the first place (dacdbb4dfc1a1: "net: macb: add fixed-link node support") will consume the device_node (if found). Signed-off-by: Brad Mouring <brad.mouring@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16net: macb: Remove redundant poll irq assignmentBrad Mouring
In phy_device's general probe, this device will already be set for phy register polling, rendering this code redundant. Signed-off-by: Brad Mouring <brad.mouring@ni.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16net: macb: Reorganize macb_mii bringupBrad Mouring
The macb mii setup (mii_probe() and mii_init()) previously was somewhat interspersed, likely a result of organic growth and hacking. This change moves mii bus registration into mii_init and probing the bus for devices into mii_probe. Signed-off-by: Brad Mouring <brad.mouring@ni.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16enic: drop IP proto check for vxlan tunnel deleteGovindarajulu Varadarajan
Commit d11790941dd3 ("enic: Add vxlan offload support for IPv6 pkts") added vxlan offload support for IPv6 pkts. Required change in enic_udp_tunnel_del was not made. This creates a bug where once user adds IPv6 tunnel, hw offload for that cannot be deleted. This patch removes check for IP proto in tunnel delete path. Driver need not check for IP proto since same UDP port cannot be used to create two tunnels. Fixes: d11790941dd3 ("enic: Add vxlan offload support for IPv6 pkts") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16brcmfmac: drop Inter-Access Point Protocol packets by defaultRafał Miłecki
Testing brcmfmac with more recent firmwares resulted in AP interfaces not working in some specific setups. Debugging resulted in discovering support for IAPP in Broadcom's firmwares. Older firmwares were only generating 802.11f frames. Newer ones like: 1) 10.10 (TOB) (r663589) 2) 10.10.122.20 (r683106) for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames in the Tx path by performing a STA disassociation. This obsoleted standard and its implementation is something that: 1) Most people don't need / want to use 2) Can allow local DoS attacks 3) Breaks AP interfaces in some specific bridge setups To solve issues it can cause this commit modifies brcmfmac to drop IAPP packets. If affects: 1) Rx path: driver won't be sending these unwanted packets up. 2) Tx path: driver will reject packets that would trigger STA disassociation perfromed by a firmware (possible local DoS attack). It appears there are some Broadcom's clients/users who care about this feature despite the drawbacks. They can switch it on using a new module param. This change results in only two more comparisons (check for module param and check for Ethernet packet length) for 99.9% of packets. Its overhead should be very minimal. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-16iwlwifi: add shared clock PHY config flag for some devicesLuca Coelho
Some devices use a shared clock which is very sensitive to variations and cause trouble in some situations. We need to set a bit in the phy configuration to indicate that to the FW. To make this generic, add a extra_phy_config_flags element to the device configuration and OR it into the phy_cfg before sending it to the firmware. And also create a set of configurations for devices that use shared clocks and need this extra bit to be set. Fixes: c62446d2b028 ("iwlwifi: add new 9460 series PCI IDs") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16iwlwifi: mvm: fix error checking for multi/broadcast staJohannes Berg
The earlier patch called the station add functions but didn't assign their return value to the ret variable, so that the checks for it were meaningless. Fix that. Found by smatch: .../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false' .../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false' Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16iwlwifi: mvm: Correctly set IGTK for APBeni Lev
Currently when an IGTK is set for an AP, it is set as a regular key. Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to the host command, which causes assert 0x253D on NICs that do not support this. Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API") Signed-off-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16iwlwifi: mvm: set the correct tid when we flush the MCAST staEmmanuel Grumbach
The tid being used for the queue (cab_queue) for the MCAST station has been changed recently to be 0 (for BE). The flush path still flushed only the special tid (15) which means that the firmware wasn't flushing the right queue and we could get a firmware crash upon remove station if we had an MCAST packet on the ring. The current code that flushes queues for a station only differentiates between internal stations (stations that aren't instantiated in mac80211, like the MCAST station) and the non-internal ones. Internal stations can be either: BCAST (beacons), MCAST (for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer injection). The internal stations can use different tids. To make the code simpler, just flush all the tids always and add the special internal tid (15) for internal stations. The firmware will know how to handle this even if we hadn't any queue mapped that that tid. Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
generated by cgit (git 2.34.1) at 2025-09-18 01:55:38 +0000