| Age | Commit message (Collapse) | Author |
|---|
|
This is the first step towards removing the P2P Device MAC.
Use ROC (which uses the AUX MAC) for P2P Device
discoveribility and action frames.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140556.8c90e457abbd.I8e340759ecb299e05b1809f3d8060429c6cbbd01@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If non-BSS and remain-on-channel (ROC) blocking were to occur
simultaneously, they'd step on each other's toes, unblocking
when not yet supported. Disentangle these bits, and ROC doesn't
need to use the non_bss_link() function then.
Fixes: a1efeb823084 ("wifi: iwlwifi: mvm: Block EMLSR when a p2p/softAP vif is active")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140556.461fcf7b95bb.Id0d21dcb739d426ff15ec068b5df8abaab58884d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Stop supporting all FWs older than the max API version.
These FW versions were supported since v6.5.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.ad6d43fe9893.I96f769e7d5be3e6499d260451df781bd694a5142@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When EMLSR gets unblocked, the current code checks if the last exit was
due to an EXIT reason (as opposed to a BLOCKING one), and if so, it
does nothing, as in this case a MLO scan was scheduled to run in 30
seconds.
But the code doesn't consider the time that passed from the last exit,
so if immediately after the exit a blocker occurred (e.g. non-BSS
interface), and lasts for more than 30 seconds, then the MLO scan and the
following link selection will decide not to enter EMLSR, and when the
unblocking event finally happens, the reason is still set to the EXIT one,
so it will do nothing, and we will not have the chance to re-enable EMLSR.
Fix this by checking also the time that has passed since the last exit,
only if it is less than 30 seconds, we can count on the scheduled MLO
scan.
Note that clearing the reason itself can't be done since it is needed
for the EMLSR prevention mechanism.
Fixes: 2f33561ea8f9 ("wifi: iwlwifi: mvm: trigger link selection after exiting EMLSR")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.58556fc4cfa9.I4c55b3cd9f20b21b37f28258d0fb6842ba413966@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was needed when we had multiple types of transports. Now we only
have pcie, so there is no need for this ops.
Cleanup the code such as the different trans APIs will call the pcie
function directly, instead of calling the callback,
and remove struct iwl_trans_ops.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.8315ff64f9f3.Ifdbc1f26d49766f7de553dcb5f613885f4ee65cc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The TX queue code was mostly moved out to support an internal
transport that we were never going to publish, but we're no
longer using that. Since we're also going to be dissolving
the virtual transport layer entirely, integrate the TX queue
code into the PCIe layer.
This also has a small kernel of already removing the virtual
transport function layer, since iwl_trans_send_cmd() calls
iwl_trans_pcie_send_hcmd() directly now, even if that still
calls the transport send_cmd method for now, we'll clean it
up later.
Also, not everything is renamed yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.936b13f45071.Ib219ce01a1e67bcad79d5131626db950252aaa46@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This needs to include dbg-tlv.h since it uses the value of
IWL_FW_INI_ALLOCATION_NUM from that file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.2d25691283eb.I0909621a0e293a8a21d4f1de6e5fd59c22e4b212@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This really isn't correct to be in the opmode, do the clamping
(and power-of-2 fixup that may be necessary due to this, or even
otherwise) in the queue code. Also move down the retrying of the
allocation, it should be after all the size fixups, but also it
just makes sense, and avoids retrying same-size allocations in
the case of the BZ-family A-step workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.000a0a1e807d.Ib822590d5aca76ff3168418ae2c139b3d43d81ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When entering D3 we want to configure skip over DTIM, but
it can't use the deflink configuration, that will not even
exist. Adjust the code to handle multiple links by taking
the min skip, even if we should only have a single active
link at this point.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.bccf980fadb4.Idc98b9f3634f39d2fae9bd9916f5d050ccd48f95@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Stop supporting older FWs.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.ff8477233010.Ic8c73bd6749cc5f8ab5297807bb0be9bd96a59fa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These entries are not used, remove them.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.0c7c520814d5.I19cefb3d81b03a5be94c029cfffd1c8b8c437182@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Setting a channel with 320 MHz channel width over hwsim results in an
array-index-out-of-bounds error. Fix it by adding 320 MHz to hwsim
supported channel widths.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605135233.a766c1465566.Ib859c7233511b61b8a34022cfceeb4971c739d80@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The flags variable is incorrectly checked while it is still cleared and
has not been assigned any value yet.
Fix it.
Fixes: a615323f7f90 ("wifi: iwlwifi: mvm: always apply 6 GHz probe limitations")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140556.291c33f9a283.Id651fe69828aebce177b49b2316c5780906f1b37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For using the ROC command, check that the ROC version
is *greater or equal* to 3, rather than *equal* to 3.
The ROC version was added to the TLV starting from
version 3.
Fixes: 67ac248e4db0 ("wifi: iwlwifi: mvm: implement ROC version 3")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.93d86cd188ad.Iceadef5a2f3cfa4a127e94a0405eba8342ec89c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Unlock the mvm mutex before returning from a
function with the mutex locked.
Fixes: a1efeb823084 ("wifi: iwlwifi: mvm: Block EMLSR when a p2p/softAP vif is active")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.96cb956db4af.Ib468cbad38959910977b5581f6111ab0afae9880@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
parameters
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TSO currently fails when the skb's gso_type field has more than one bit
set.
TSO packets can be passed from userspace using PF_PACKET, TUNTAP and a
few others, using virtio_net_hdr (e.g., PACKET_VNET_HDR). This includes
virtualization, such as QEMU, a real use-case.
The gso_type and gso_size fields as passed from userspace in
virtio_net_hdr are not trusted blindly by the kernel. It adds gso_type
|= SKB_GSO_DODGY to force the packet to enter the software GSO stack
for verification.
This issue might similarly come up when the CWR bit is set in the TCP
header for congestion control, causing the SKB_GSO_TCP_ECN gso_type bit
to be set.
Fixes: a57e5de476be ("gve: DQO: Add TX path")
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
v2 - Remove unnecessary comments, remove line break between fixes tag
and signoffs.
v3 - Add back unrelated empty line removal.
Link: https://lore.kernel.org/r/20240610225729.2985343-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The vrf driver has its own dstats-to-rtnl_link_stats64 collection, but
we now have a generic implementation for dstats collection, so switch to
this.
In doing so, we fix a minor issue where the (non-percpu)
dev->stats->tx_errors value was never collected into rtnl_link_stats64,
as the generic dev_get_dstats64() consumes the starting values from
dev->stats.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240607-dstats-v3-3-cc781fe116f7@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pcpu_sw_netstats and pcpu_lstats structs both contain a set of
u64_stats_t fields for individual stats, but pcpu_dstats uses u64s
instead.
Make this consistent by using u64_stats_t across all stats types.
The per-cpu dstats are only used by the vrf driver at present, so update
that driver as part of this change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240607-dstats-v3-1-cc781fe116f7@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever per pdev debugfs directory is created, a symlink to it is also
placed in ieee80211/phy* directory. During clean up of per pdev debugfs,
this symlink also needs to be cleaned up.
Add changes to clean up the symlink whenever the per pdev debugfs is
removed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-4-quic_adisi@quicinc.com
|
|
During normal de-initialization path or if any error happens while
registering the hardware, there is no support to unregister the per pdev
debugfs. Add support for the same.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-3-quic_adisi@quicinc.com
|
|
Function ath12k_debugfs_register() is called once inside the function
ath12k_mac_hw_register(). However, with single wiphy model, there could
be multiple pdevs registered under single hardware. Hence, need to register
debugfs for each one of them.
Move the caller inside the loop which iterates over all underlying pdevs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: f8bde02a26b9 ("wifi: ath12k: initial debugfs support")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529043043.2488031-2-quic_adisi@quicinc.com
|
|
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in ath11k_install_key()
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set. And in ath11k_mac_mgmt_tx_wmi()
a length of IEEE80211_CCMP_MIC_LEN is reserved for all ciphers.
This results in unexpected management frame drop in case either of above 3 ciphers
is used. The reason is, without IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211
will not generate CCMP/GCMP headers in frame for ath11k. Also MIC length reserved
is wrong. Such frame is dropped later by hardware:
ath11k_pci 0000:5a:00.0: mac tx mgmt frame, buf id 0
ath11k_pci 0000:5a:00.0: mgmt tx compl ev pdev_id 1, desc_id 0, status 1
From user point of view, we have observed very low throughput due to this issue:
action frames are all dropped so ADDBA response from DUT never reaches AP. AP
can not use aggregation thus throughput is low.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag and by reserving proper
MIC length for those ciphers.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Tested-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Closes: https://lore.kernel.org/all/CADS+iDX5=JtJr0apAtAQ02WWBxgOFEv8G063vuGYwDTC8AVZaw@mail.gmail.com
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240605014826.22498-1-quic_bqiang@quicinc.com
|
|
Currently, in the Rx error processing handler, once an MSDU drop is
detected, the subsequent MSDUs get unintentionally dropped due to the
previous drop flag being retained across all MSDU processing, leading
to the discarding of valid MSDUs. To resolve this issue, the drop flag
should be reset to false before processing each descriptor.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240604062641.2956288-1-quic_periyasa@quicinc.com
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240603091541.8367-2-wsa+renesas@sang-engineering.com
|
|
Current documentation on RCU in ath11k_mac_op_ipv6_changed() says:
/* Note: read_lock_bh() calls rcu_read_lock() */
read_lock_bh(&idev->lock);
This is wrong because without enabling CONFIG_PREEMPT_RT
rcu_read_lock() is not called by read_lock_bh(). The reason
why current code works even in a CONFIG_PREEMPT_RT=n kernel
is because atomic_notifier_call_chain() already does that for
us, see:
int atomic_notifier_call_chain()
{
...
rcu_read_lock();
ret = notifier_call_chain(&nh->head, val, v, -1, NULL);
rcu_read_unlock();
...
}
and backtrace:
ath11k_mac_op_ipv6_changed
ieee80211_ifa6_changed
notifier_call_chain
atomic_notifier_call_chain
So update the comment to make it correct.
This is found during code review, compile tested only.
Fixes: feafe59c8975 ("wifi: ath11k: use RCU when accessing struct inet6_dev::ac_list")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531022411.6543-1-quic_bqiang@quicinc.com
|
|
Currently ACPI notification handler is installed when driver loads and only
gets removed when driver unloads. During resume after firmware is reloaded,
ath12k tries to install it by default. Since it is installed already, ACPI
subsystem rejects it and returns an error:
[ 83.094206] ath12k_pci 0000:03:00.0: failed to install DSM notify callback: 7
Fix it by removing that handler when going to suspend. This also avoid any
possible ACPI call to firmware before firmware is reloaded/reinitialized.
Note ab->acpi also needs to be cleared in ath12k_acpi_stop() such that we
are in a clean state when ACPI structures are reinitialized in
ath12k_acpi_start().
Tested-on: WCN7850 HW2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 576771c9fa21 ("wifi: ath12k: ACPI TAS support")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240531024000.9291-1-quic_bqiang@quicinc.com
|
|
When multiple radios are advertised as a single wiphy which supports various
bands, vdev creation for the vif is deferred until channel is assigned to it.
If a remain on channel (RoC) request is received from mac80211, select the
corresponding radio (ar) based on channel and create a vdev on that radio to
initiate an RoC scan.
Note that on RoC completion this vdev is not deleted. If a new RoC/hw scan
request is seen on that same vif for a different band the vdev will be deleted
and created on the new radio supporting the request.
Also if the RoC scan is requested when the vdev is in started state, no
switching to new radio is allowed and RoC request can be accepted only on
channels within same radio.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240528082739.1226758-1-quic_ramess@quicinc.com
|
|
irq_set_affinity_hint() is deprecated. Use irq_update_affinity_hint()
instead. This removes the side-effect of actually applying the affinity.
The driver does not really need to worry about spreading its IRQs across
CPUs. The core code already takes care of that.
On the contrary, when the driver applies affinities by itself, it breaks
the users' expectations:
1. The user configures irqbalance with IRQBALANCE_BANNED_CPULIST in
order to prevent IRQs from being moved to certain CPUs that run a
real-time workload.
2. ice reconfigures VSIs at runtime due to a MIB change
(ice_dcb_process_lldp_set_mib_change). Reopening a VSI resets the
affinity in ice_vsi_req_irq_msix().
3. ice has no idea about irqbalance's config, so it may move an IRQ to
a banned CPU. The real-time workload suffers unacceptable latency.
I am not sure if updating the affinity hints is at all useful, because
irqbalance ignores them since 2016 ([1]), but at least it's harmless.
This ice change is similar to i40e commit d34c54d1739c ("i40e: Use
irq_update_affinity_hint()").
[1] https://github.com/Irqbalance/irqbalance/commit/dcc411e7bfdd
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-3-d1470cee3347@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ice_ptp_cfg_clkout(), the ice driver needs to calculate the nearest next
second of a current time value specified in nanoseconds. It implements this
using div64_u64, because the time value is a u64. It could use div_u64
since NSEC_PER_SEC is smaller than 32-bits.
Ideally this would be implemented directly with roundup(), but that can't
work on all platforms due to a division which requires using the specific
macros and functions due to platform restrictions, and to ensure that the
most appropriate and fast instructions are used.
The kernel doesn't currently provide any 64-bit equivalents for doing
roundup. Attempting to use roundup() on a 32-bit platform will result in a
link failure due to not having a direct 64-bit division.
The closest equivalent for this is DIV64_U64_ROUND_UP, which does a
division always rounding up. However, this only computes the division, and
forces use of the div64_u64 in cases where the divisor is a 32bit value and
could make use of div_u64.
Introduce DIV_U64_ROUND_UP based on div_u64, and then use it to implement
roundup_u64 which takes a u64 input value and a u32 rounding value.
The name roundup_u64 matches the naming scheme of div_u64, and future
patches could implement roundup64_u64 if they need to round by a multiple
that is greater than 32-bits.
Replace the logic in ice_ptp.c which does this equivalent with the newly
added roundup_u64.
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-2-d1470cee3347@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-1-d1470cee3347@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70ac ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kernel.h is included solely for some other existing headers.
Include them directly and get rid of kernel.h.
While at it, sort headers alphabetically for easier maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The documentation for device_get_named_child_node() mentions this
important point:
"
The caller is responsible for calling fwnode_handle_put() on the
returned fwnode pointer.
"
Add fwnode_handle_put() to avoid leaked references.
Fixes: 1e264f9d2918 ("net: dsa: qca8k: add LEDs basic support")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default ndo_get_iflink() implementation returns the current ifindex
of the netdev. But the overridden nsim_get_iflink() returns 0 if the
current nsim is not linked, breaking backwards compatibility for
userspace that depend on this behaviour.
Fix the problem by returning the current ifindex if not linked to a
peer.
Fixes: 8debcf5832c3 ("netdevsim: add ndo_get_iflink() implementation")
Reported-by: Yu Watanabe <watanabe.yu@gmail.com>
Suggested-by: Yu Watanabe <watanabe.yu@gmail.com>
Signed-off-by: David Wei <dw@davidwei.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ACLs that reside in the algorithmic TCAM (A-TCAM) in Spectrum-2 and
newer ASICs can share the same mask if their masks only differ in up to
8 consecutive bits. For example, consider the following filters:
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 192.0.2.0/24 action drop
# tc filter add dev swp1 ingress pref 1 proto ip flower dst_ip 198.51.100.128/25 action drop
The second filter can use the same mask as the first (dst_ip/24) with a
delta of 1 bit.
However, the above only works because the two filters have different
values in the common unmasked part (dst_ip/24). When entries have the
same value in the common unmasked part they create undesired collisions
in the device since many entries now have the same key. This leads to
firmware errors such as [1] and to a reduced scale.
Fix by adjusting the hash table key to only include the value in the
common unmasked part. That is, without including the delta bits. That
way the driver will detect the collision during filter insertion and
spill the filter into the circuit TCAM (C-TCAM).
Add a test case that fails without the fix and adjust existing cases
that check C-TCAM spillage according to the above limitation.
[1]
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=3379b18a00003394,reg_id=3027(ptce3),type=write,status=8(resource not available))
Fixes: c22291f7cf45 ("mlxsw: spectrum: acl: Implement delta for ERP")
Reported-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM
(A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can
contain more ACLs (i.e., tc filters), but the number of masks in each
region (i.e., tc chain) is limited.
In order to mitigate the effects of the above limitation, the device
allows filters to share a single mask if their masks only differ in up
to 8 consecutive bits. For example, dst_ip/25 can be represented using
dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the
number of masks being used (and therefore does not support mask
aggregation), but can contain a limited number of filters.
The driver uses the "objagg" library to perform the mask aggregation by
passing it objects that consist of the filter's mask and whether the
filter is to be inserted into the A-TCAM or the C-TCAM since filters in
different TCAMs cannot share a mask.
The set of created objects is dependent on the insertion order of the
filters and is not necessarily optimal. Therefore, the driver will
periodically ask the library to compute a more optimal set ("hints") by
looking at all the existing objects.
When the library asks the driver whether two objects can be aggregated
the driver only compares the provided masks and ignores the A-TCAM /
C-TCAM indication. This is the right thing to do since the goal is to
move as many filters as possible to the A-TCAM. The driver also forbids
two identical masks from being aggregated since this can only happen if
one was intentionally put in the C-TCAM to avoid a conflict in the
A-TCAM.
The above can result in the following set of hints:
H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta
H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta
After getting the hints from the library the driver will start migrating
filters from one region to another while consulting the computed hints
and instructing the device to perform a lookup in both regions during
the transition.
Assuming a filter with mask X is being migrated into the A-TCAM in the
new region, the hints lookup will return H1. Since H2 is the parent of
H1, the library will try to find the object associated with it and
create it if necessary in which case another hints lookup (recursive)
will be performed. This hints lookup for {mask Y, A-TCAM} will either
return H2 or H3 since the driver passes the library an object comparison
function that ignores the A-TCAM / C-TCAM indication.
This can eventually lead to nested objects which are not supported by
the library [1].
Fix by removing the object comparison function from both the driver and
the library as the driver was the only user. That way the lookup will
only return exact matches.
I do not have a reliable reproducer that can reproduce the issue in a
timely manner, but before the fix the issue would reproduce in several
minutes and with the fix it does not reproduce in over an hour.
Note that the current usefulness of the hints is limited because they
include the C-TCAM indication and represent aggregation that cannot
actually happen. This will be addressed in net-next.
[1]
WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0
Modules linked in:
CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42
Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0
[...]
Call Trace:
<TASK>
__objagg_obj_get+0x2bb/0x580
objagg_obj_get+0xe/0x80
mlxsw_sp_acl_erp_mask_get+0xb5/0xf0
mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270
mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510
process_one_work+0x151/0x370
Fixes: 9069a3817d82 ("lib: objagg: implement optimization hints assembly and use hints for object creation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The key is encoded, not encrypted.
Fixes: c22291f7cf45 ("mlxsw: spectrum: acl: Implement delta for ERP")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Tested-by: Alexander Zubkov <green@qrator.net>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the k3_udma_glue_rx_get_irq() function returns either negative
error codes or zero on error. Generally, in the kernel, zero means
success so this be confusing and has caused bugs in the past. Also the
"tx" version of this function only returns negative error codes. Let's
clean this "rx" function so both functions match.
This patch has no effect on runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 070246e4674b ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.
Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.
Fixes: 8c4d92e82d50 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Process QP fatal events from the error event queue.
For that, find the QP, using QPN from the event, and then call its
event_handler. To find the QPs, store created RC QPs in an xarray.
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://lore.kernel.org/r/1717754897-19858-1-git-send-email-kotaranov@linux.microsoft.com
Reviewed-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f327913 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add multicast filtering support for ICSSG Driver. Multicast addresses will
be updated by __dev_mc_sync() API. icssg_prueth_add_macst () and
icssg_prueth_del_mcast() will be sync and unsync APIs for the driver
respectively.
To add a mac_address for a port, driver needs to call icssg_fdb_add_del()
and pass the mac_address and BIT(port_id) to the API. The ICSSG firmware
will then configure the rules and allow filtering.
If a mac_address is added to port0 and the same mac_address needs to be
added for port1, driver needs to pass BIT(port0) | BIT(port1) to the
icssg_fdb_add_del() API. If driver just pass BIT(port1) then the entry for
port0 will be overwritten / lost. This is a design constraint on the
firmware side.
To overcome this in the driver, to add any mac_address for let's say portX
driver first checks if the same mac_address is already added for any other
port. If yes driver calls icssg_fdb_add_del() with BIT(portX) |
BIT(other_existing_port). If not, driver calls icssg_fdb_add_del() with
BIT(portX).
The same thing is applicable for deleting mac_addresses as well. This
logic is in icssg_prueth_add_mcast / icssg_prueth_del_mcast APIs.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe29 ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When link status change, the nic driver need to notify the roce
driver to handle this event, but at this time, the roce driver
may uninit, then cause kernel crash.
To fix the problem, when link status change, need to check
whether the roce registered, and when uninit, need to wait link
update finish.
Fixes: 45e92b7e4e27 ("net: hns3: add calling roce callback function when link status change")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some docks support MAC pass-through - MAC address
is taken from another device.
Driver should indicate that with NET_ADDR_STOLEN flag.
This should help to avoid collisions if network interface
names are generated with MAC policy.
Reported and discussed here
https://github.com/systemd/systemd/issues/33104
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605153340.25694-1-gmazyland@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/pensando/ionic/ionic_txrx.c
d9c04209990b ("ionic: Mark error paths in the data path as unlikely")
491aee894a08 ("ionic: fix kernel panic in XDP_TX action")
net/ipv6/ip6_fib.c
b4cb4a1391dc ("net: use unrcu_pointer() helper")
b01e1c030770 ("ipv6: fix possible race in __fib6_drop_pcpu_from()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
