| Age | Commit message (Collapse) | Author |
|---|
|
Have bnxt call page_pool_disable_direct_recycling() to unlink the old
page pool when resetting a queue prior to destroying it, instead of
touching a netdev core struct directly.
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RCK is synchronize RC calibration. Driver triggers this calibration and
writes the result to registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-5-pkshih@realtek.com
|
|
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-4-pkshih@realtek.com
|
|
RX DCK stands for receiver DC calibration. With this calibration, we have
proper DC offset to reflect correct received signal strength indicator.
Do this calibration when bringing up interface and going to connect.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-3-pkshih@realtek.com
|
|
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration once we are going to an AP. During
scanning phase, without this calibration RF performance is still
acceptable because it transmits and receives with low data rate at
this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-2-pkshih@realtek.com
|
|
Calculate a TX power constraint based on content of ieee80211 Transmit
Power Envelope (TPE). Since HW control registers aren't designed as many
as all kinds of TPE fields, we strictly intersect all TPE inputs in driver.
Then, according to result, constrain TX power via TX power limit/limit_RU.
Besides, extend dbgfs txpwr_table to show info about 6 GHz regulatory.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023237.7901-1-pkshih@realtek.com
|
|
Add additional policy option to let Bluetooth audio can play well
during Wi-Fi is hardware scanning.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023129.7776-1-pkshih@realtek.com
|
|
phy_suspend() checks the WoL status, and then dereferences
phydrv->flags if (and only if) we decided that WoL has been enabled
on either the PHY or the netdev.
We then check whether phydrv was NULL, but we've potentially already
dereferenced the pointer.
If phydrv is NULL, then phy_ethtool_get_wol() will return an error
and leave wol.wolopts set to zero. However, if netdev->wol_enabled
is true, then we would dereference a NULL pointer.
Checking the PHY drivers, the only place that phydev->wol_enabled is
checked by them is in their suspend/resume callbacks and nowhere else
(which is correct, because phylib only updates this in phy_suspend()).
So, move the NULL pointer check earlier to avoid a NULL pointer
dereference. Leave the check for phydrv->suspend in place as a driver
may populate the .resume method but not the .suspend method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1sN8tn-00GDCZ-Jj@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On vPro systems, the configuration of the I219-LM to achieve power
gating and S0ix residency is split between the driver and the CSME FW.
It was discovered that in some scenarios, where the network cable is
connected and then disconnected, S0ix residency is not always reached.
This was root-caused to a subset of I219-LM register writes that are not
performed by the CSME FW. Therefore, the driver should perform these
register writes on corporate setups, regardless of the CSME FW state.
This was discovered on Meteor Lake systems; however it is likely to
appear on other platforms as well.
Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218589
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240628201754.2744221-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-06-29
Geert Uytterhoeven contributes 3 patches with small improvements and
cleanups for the rcar_canfd driver.
A patch by Christophe JAILLET constifies the struct m_can_ops in the
m_can driver to reduce the code size.
The last 9 patches are by me an work around erratum DS80000789E 6 of
mcp2518fd.
* tag 'linux-can-next-for-6.11-20240629' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: mcp251xfd: tef: update workaround for erratum DS80000789E 6 of mcp2518fd
can: mcp251xfd: tef: prepare to workaround broken TEF FIFO tail index erratum
can: mcp251xfd: rx: add workaround for erratum DS80000789E 6 of mcp2518fd
can: mcp251xfd: rx: prepare to workaround broken RX FIFO head index erratum
can: mcp251xfd: mcp251xfd_handle_rxif_ring_uinc(): factor out in separate function
can: mcp251xfd: clarify the meaning of timestamp
can: mcp251xfd: move mcp251xfd_timestamp_start()/stop() into mcp251xfd_chip_start/stop()
can: mcp251xfd: update errata references
can: mcp251xfd: properly indent labels
can: gs_usb: add VID/PID for Xylanta SAINT3 product family
can: m_can: Constify struct m_can_ops
can: rcar_canfd: Remove superfluous parentheses in address calculations
can: rcar_canfd: Improve printing of global operational state
can: rcar_canfd: Simplify clock handling
====================
Link: https://patch.msgid.link/20240629114017.1080160-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to request pdev TQM stats from firmware through HTT stats
type 6. This stat type gives information such as TQM error, MPDU
related information and TQM pdev stats.
Sample output:
-------------
echo 6 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TX_TQM_ERROR_STATS_TLV:
q_empty_failure = 0
q_not_empty_failure = 0
add_msdu_failure = 0
TQM_ERROR_RESET_STATS:
tqm_cache_ctl_err = 0
tqm_soft_reset = 0
tqm_reset_total_num_in_use_link_descs = 0
.....
HTT_TX_TQM_GEN_MPDU_STATS_TLV:
gen_mpdu_end_reason = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0,
10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0
HTT_TX_TQM_LIST_MPDU_STATS_TLV:
list_mpdu_end_reason = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0,
10:0, 11:0, 12:0
HTT_TX_TQM_LIST_MPDU_CNT_TLV_V:
list_mpdu_cnt_hist = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
HTT_TX_TQM_PDEV_STATS_TLV_V:
msdu_count = 0
mpdu_count = 0
remove_msdu = 0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240625042217.1303332-4-quic_rdevanat@quicinc.com
|
|
Add support to request pdev error stats from firmware through HTT stats
type 5. This stats type gives information such as list of pdev errors,
reasons for reset, logging information about recovery, drain and war
stats. etc.
Sample output:
-------------
echo 5 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_HW_STATS_PDEV_ERRS_TLV:
mac_id = 0
tx_abort = 0
tx_abort_fail_count = 0
rx_abort = 53
.....
PDEV_PHY_WARM_RESET_REASONS:
phy_warm_reset_reason_phy_m3 = 0
phy_warm_reset_reason_tx_hw_stuck = 0
phy_warm_reset_reason_num_cca_rx_frame_stuck = 0
.....
WAL_RX_RECOVERY_STATS:
wal_rx_recovery_rst_mac_hang_count = 0
wal_rx_recovery_rst_known_sig_count = 0
wal_rx_recovery_rst_no_rx_count = 0
.....
HTT_RX_DEST_DRAIN_STATS:
rx_dest_drain_rx_descs_leak_prevention_done = 0
rx_dest_drain_rx_descs_saved_cnt = 0
rx_dest_drain_rxdma2reo_leak_detected = 0
.....
HTT_HW_STATS_INTR_MISC_TLV:
hw_intr_name = AMPI
mask = 0
count = 2
HTT_HW_STATS_WHAL_TX_TLV:
mac_id = 0
last_unpause_ppdu_id = 0
hwsch_unpause_wait_tqm_write = 0
.....
HTT_HW_WAR_STATS_TLV:
mac_id = 0
hw_war 0 = 0
hw_war 1 = 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240625042217.1303332-3-quic_rdevanat@quicinc.com
|
|
Add support to request transmission scheduler stats from firmware through
HTT stats type 4. This stat gives information such as pdev stats
scheduled per transmission queue, transmission queue command posted and
reaped, scheduler order, scheduler ineligibility and supercycle triggers.
Sample output:
-------------
echo 4 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_STATS_TX_SCHED_CMN_TLV:
mac_id = 0
current_timestamp = 952546828
HTT_TX_PDEV_STATS_SCHED_PER_TXQ_TLV:
mac_id = 0
txq_id = 14
sched_policy = 2
.....
HTT_SCHED_TXQ_CMD_POSTED_TLV:
sched_cmd_posted = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0,
10:0, 11:0, 12:0
HTT_SCHED_TXQ_CMD_REAPED_TLV:
sched_cmd_reaped = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0,
10:0, 11:0, 12:0
HTT_SCHED_TXQ_SCHED_ORDER_SU_TLV:
sched_order_su = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0,
11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0
HTT_SCHED_TXQ_SCHED_INELIGIBILITY:
sched_ineligibility = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0,
10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0,
22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0,
34:0, 35:0
HTT_SCHED_TXQ_SUPERCYCLE_TRIGGER:
supercycle_triggers = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240625042217.1303332-2-quic_rdevanat@quicinc.com
|
|
Support to dump additional Tx PDEV stats through HTT stats debugfs.
Following stats dump are supported:
1. PDEV control path stat to dump Tx management frame count
2. Tx PDEV SIFS histogram stats
3. Tx MU MIMO PPDU stats for 802.11ac, 802.11ax and 802.11be
Sample Output:
---------------
echo 1 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TX_PDEV_STATS_CMN_TLV:
mac_id = 0
comp_delivered = 0
self_triggers = 13
......
......
HTT_TX_PDEV_STATS_CTRL_PATH_TX_STATS:
fw_tx_mgmt_subtype = 0:1, 1:0, 2:0, 3:0, 4:38, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:1, 12:0, 13:7, 14:0, 15:0
HTT_TX_PDEV_STATS_SIFS_HIST_TLV:
sifs_hist_status = 0:237, 1:185, 2:1, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
HTT_TX_PDEV_AC_MU_PPDU_DISTRIBUTION_STATS:
ac_mu_mimo_num_seq_posted_nr4 = 0
ac_mu_mimo_num_ppdu_posted_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ac_mu_mimo_num_ppdu_completed_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ac_mu_mimo_num_seq_term_status_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
ac_mu_mimo_num_seq_posted_nr8 = 0
ac_mu_mimo_num_ppdu_posted_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ac_mu_mimo_num_ppdu_completed_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ac_mu_mimo_num_seq_term_status_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
HTT_TX_PDEV_AX_MU_PPDU_DISTRIBUTION_STATS:
ax_mu_mimo_num_seq_posted_nr4 = 0
ax_mu_mimo_num_ppdu_posted_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ax_mu_mimo_num_ppdu_completed_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ax_mu_mimo_num_seq_term_status_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
ax_mu_mimo_num_seq_posted_nr8 = 0
ax_mu_mimo_num_ppdu_posted_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ax_mu_mimo_num_ppdu_completed_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
ax_mu_mimo_num_seq_term_status_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
HTT_TX_PDEV_BE_MU_PPDU_DISTRIBUTION_STATS:
be_mu_mimo_num_seq_posted_nr4 = 0
be_mu_mimo_num_ppdu_posted_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
be_mu_mimo_num_ppdu_completed_per_burst_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
be_mu_mimo_num_seq_term_status_nr4 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
be_mu_mimo_num_seq_posted_nr8 = 0
be_mu_mimo_num_ppdu_posted_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
be_mu_mimo_num_ppdu_completed_per_burst_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0
be_mu_mimo_num_seq_term_status_nr8 = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626085854.2500681-5-quic_rgnanase@quicinc.com
|
|
Add extended htt stats parser and print the corresponding TLVs associated
with the requested htt_stats_type.
Add support for TX PDEV related htt stats.
Sample output:
--------------
echo 1 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TX_PDEV_STATS_CMN_TLV:
mac_id = 0
comp_delivered = 0
self_triggers = 256
hw_queued = 275
hw_reaped = 275
underrun = 241
hw_paused = 0
hw_flush = 0
hw_filt = 1
tx_abort = 0
ppdu_ok = 246
mpdu_requeued = 0
tx_xretry = 0
data_rc = 3
mpdu_dropped_xretry = 0
illegal_rate_phy_err = 0
cont_xretry = 0
tx_timeout = 0
tx_time_dur_data = 0
pdev_resets = 0
phy_underrun = 0
txop_ovf = 0
seq_posted = 247
seq_failed_queueing = 0
seq_completed = 247
seq_restarted = 0
seq_txop_repost_stop = 0
next_seq_cancel = 0
dl_mu_mimo_seq_posted = 0
dl_mu_ofdma_seq_posted = 0
ul_mu_mimo_seq_posted = 0
ul_mu_ofdma_seq_posted = 0
mu_mimo_peer_blacklisted = 0
seq_qdepth_repost_stop = 0
seq_min_msdu_repost_stop = 0
mu_seq_min_msdu_repost_stop = 0
seq_switch_hw_paused = 0
next_seq_posted_dsr = 0
seq_posted_isr = 0
seq_ctrl_cached = 0
mpdu_count_tqm = 0
msdu_count_tqm = 0
mpdu_removed_tqm = 0
msdu_removed_tqm = 0
remove_mpdus_max_retries = 0
mpdus_sw_flush = 0
mpdus_hw_filter = 0
mpdus_truncated = 0
mpdus_ack_failed = 0
mpdus_expired = 0
mpdus_seq_hw_retry = 0
ack_tlv_proc = 0
coex_abort_mpdu_cnt_valid = 0
coex_abort_mpdu_cnt = 5
num_total_ppdus_tried_ota = 5
num_data_ppdus_tried_ota = 0
local_ctrl_mgmt_enqued = 247
local_ctrl_mgmt_freed = 247
local_data_enqued = 0
local_data_freed = 0
mpdu_tried = 0
isr_wait_seq_posted = 0
tx_active_dur_us_low = 0
tx_active_dur_us_high = 0
fes_offsets_err_cnt = 0
HTT_TX_PDEV_STATS_URRN_TLV:
urrn_stats = 0:0, 1:241, 2:0
HTT_TX_PDEV_STATS_SIFS_TLV:
sifs_status = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
HTT_TX_PDEV_STATS_FLUSH_TLV:
flush_errs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0,
11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0,
23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0,
35:0, 36:0, 37:0, 38:0, 39:0, 40:0, 41:0, 42:0, 43:0, 44:0, 45:0, 46:0,
47:0, 48:0, 49:0, 50:0, 51:0, 52:0, 53:0, 54:0, 55:0, 56:0, 57:0, 58:0,
59:0, 60:0, 61:0, 62:0, 63:0, 64:0, 65:0, 66:0, 67:0, 68:0, 69:0, 70:0,
71:0, 72:0, 73:0, 74:0, 75:0, 76:0, 77:0, 78:0, 79:0, 80:0, 81:0, 82:0,
83:0, 84:0, 85:0, 86:0, 87:0, 88:0, 89:0, 90:0, 91:0, 92:0, 93:0, 94:0,
95:0, 96:0, 97:0, 98:0, 99:0, 100:0, 101:0, 102:0, 103:0, 104:0, 105:0,
106:0, 107:0, 108:0, 109:0, 110:0, 111:0, 112:0, 113:0, 114:0, 115:0,
116:0, 117:0, 118:0, 119:0, 120:0, 121:0, 122:0, 123:0, 124:0, 125:0,
126:0, 127:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626085854.2500681-4-quic_rgnanase@quicinc.com
|
|
Add dump_htt_stats file operation to dump the stats value requested
for the requested stats_type.
Stats sent from firmware will be cumulative. Hence add debugfs to reset
the requested stats type.
Example with one ath12k device:
ath12k
`-- pci-0000:06:00.0
|-- mac0
`-- htt_stats
|-- htt_stats_type
|-- htt_stats_reset
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626085854.2500681-3-quic_rgnanase@quicinc.com
|
|
Create debugfs_htt_stats file when ath12k debugfs support is enabled.
Add basic ath12k_debugfs_htt_stats_register and handle htt_stats_type
file operations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626085854.2500681-2-quic_rgnanase@quicinc.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue into main
Tony nguyen says:
====================
Intel Wired LAN Driver Updates 2024-06-28 (MAINTAINERS, ice)
This series contains updates to MAINTAINERS file and ice driver.
Jesse replaces himself with Przemek in the maintainers file.
Karthik Sundaravel adds support for VF get/set MAC address via devlink.
Eric checks for errors from ice_vsi_rebuild() during queue
reconfiguration.
Paul adjusts FW API version check for E830 devices.
Piotr adds differentiation of unload type when shutting down AdminQ.
Przemek changes ice_adapter initialization to occur once per physical
card.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we require the spinlock to protect ptp->txts_prod, change
ptp->tx_avail to non-atomic and protect it under the same spinlock.
Add a new helper function bnxt_ptp_get_txts_prod() to decrement
ptp->tx_avail under spinlock and return the producer.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Start accepting up to 4 TX TS requests on BCM5750X (P5) chips.
These PTP TX packets will be queued in the ptp->txts_req[] array
waiting for the TX timestamp to complete. The entries in the
array will be managed by a producer and consumer index. The
producer index is updated under spinlock since multiple TX rings
can try to send PTP packets at the same time.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the function bnxt_stamp_tx_skb() to return 0 for suceess
or -EAGAIN if the timestamp is still pending in firmware. The
calling PTP aux worker will reschedule based on the return code.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current 5750X PTP code paths, there is always at most one TX
SKB requested for timestamp and we won't accept another one until we
have retrieved the timestamp or it has timed out. Remove the
unnecessary check in bnxt_get_tx_ts_p5() for a pending SKB and change
the function to void.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the older 5750X (P5) chips, we currently support only 1 TX PTP
packet in-flight waiting for the timestamp. Refactor the
datastructures to prepare to support up to 4 TX PTP packets.
Combine all fields required for PTP TX timestamp query into one
structure. An array of this structure will be added in follow-on
patches to support multiple outstanding TX timestamps.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM5760X firmware will advertise direct 64-bit PHC registers access
for the driver from BAR0.
Make the necessary changes in handling HWRM_PORT_MAC_PTP_QCFG's
response and PHC register mapping for 5760X chips.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new BCM5760X chips will return the timestamp of TX packets in a
new completion. Add logic in __bnxt_poll_work() to handle this
completion type to retrieve the timestamp. This feature eliminates
the limit on the number of in-flight PTP TX packets.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver's current logic will always free all the TX SKBs up to
txr->tx_hw_cons within NAPI. In the next patches, we'll be adding
logic to handle TX timestamp completion and we may need to hold
some remaining TX SKBs if we don't have the timestamp completions
yet.
Modify __bnxt_poll_work_done() to clear each event bit separately to
allow bnapi->tx_int() to decide whether to clear BNXT_TX_CMP_EVENT or
not. bnapi->tx_int() will not clear BNXT_TX_CMP_EVENT if some TX
SKBs are held waiting for TX timestamps. Note that legacy chips will
never hold any SKBs this way. The SKB is always deferred to the PTP
worker slow path to retrieve the timestamp from firmware. On the new
P7 chips, the timestamp is returned by the hardware directly and we
can retrieve it directly from NAPI.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unused is_gso field and add the is_ts_pkt field to struct
bnxt_sw_tx_bd. This field will mark the TX BD that has requested
HW TX timestamp. The field needs to be cleared if the timestamp packet
is later aborted. This field will be useful when processing the
new TX timestamp completion from the hardware in the next patches.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new BCM5760X chips will generate this new TX timestamp completion
when a TX packet's timestamp has been taken right before transmission.
The driver logic to retrieve the timestamp will be added in the next
few patches.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Octeontx2 hardware uses Near Data Cache(NDC) block to cache
contexts in it so that access to LLC/DRAM can be avoided.
It is recommended in HRM to sync the NDC contents before
releasing/resetting LF resources. Hence implement NDC_SYNC
mailbox and sync contexts during driver teardown.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call phylink_ethtool_ksettings_get() for get_link_ksettings method and
ethtool_op_get_link() for get_link method.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek RTL8211F Ethernet PHY supports 3 LED pins which are used to
indicate link status and activity. Add minimal LED controller driver
supporting the most common uses with the 'netdev' trigger.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20240628194529.312968-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The core now always satisfies 'ethtool -x context nonzero' from its own
tracking, so our lookup code for that case is never called. Remove it.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/b426fcc416dedc8f203e52eebef6891eccebe4c1.1719502240.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The core is now responsible for allocating IDs and a memory region for
us to store our state (struct efx_rss_context_priv), so we no longer
need efx_alloc_rss_context_entry() and friends.
Since the contexts are now maintained by the core, use the core's lock
(net_dev->ethtool->rss_lock), rather than our own mutex (efx->rss_lock),
to serialise access against changes; and remove the now-unused
efx->rss_lock from struct efx_nic.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/150274740ea8cc137fef5502541ce573d32fb319.1719502240.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net_dev->ethtool is a pointer to new struct ethtool_netdev_state, which
currently contains only the wol_enabled field.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/293a562278371de7534ed1eb17531838ca090633.1719502239.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add .get_channel to enic_ethtool_ops to enable basic ethtool -l
support to get the current channel configuration.
Note that the driver does not support dynamically changing queue
configuration, so .set_channel is intentionally unused. Instead, users
should use Cisco's hardware management tools (UCSM/IMC) to modify
virtual interface card configuration out of band.
Signed-off-by: Jon Kohler <jon@nutanix.com>
Link: https://patch.msgid.link/20240627202013.2398217-1-jon@nutanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix UBSAN warnings that occur when using a system with 32 physical
cpu cores or more, or when the user defines a number of Ethernet
queues greater than or equal to FP_SB_MAX_E1x using the num_queues
module parameter.
Currently there is a read/write out of bounds that occurs on the array
"struct stats_query_entry query" present inside the "bnx2x_fw_stats_req"
struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h".
Looking at the definition of the "struct stats_query_entry query" array:
struct stats_query_entry query[FP_SB_MAX_E1x+
BNX2X_FIRST_QUEUE_QUERY_IDX];
FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and
has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3
meaning the array has a total size of 19.
Since accesses to "struct stats_query_entry query" are offset-ted by
BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet
queues should not exceed FP_SB_MAX_E1x (16). However one of these queues
is reserved for FCOE and thus the number of Ethernet queues should be set
to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if
it is not.
This is also described in a comment in the source code in
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition
of FP_SB_MAX_E1x. Below is the part of this explanation that it important
for this patch
/*
* The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is
* control by the number of fast-path status blocks supported by the
* device (HW/FW). Each fast-path status block (FP-SB) aka non-default
* status block represents an independent interrupts context that can
* serve a regular L2 networking queue. However special L2 queues such
* as the FCoE queue do not require a FP-SB and other components like
* the CNIC may consume FP-SB reducing the number of possible L2 queues
*
* If the maximum number of FP-SB available is X then:
* a. If CNIC is supported it consumes 1 FP-SB thus the max number of
* regular L2 queues is Y=X-1
* b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* c. If the FCoE L2 queue is supported the actual number of L2 queues
* is Y+1
* d. The number of irqs (MSIX vectors) is either Y+1 (one extra for
* slow-path interrupts) or Y+2 if CNIC is supported (one additional
* FP interrupt context for the CNIC).
* e. The number of HW context (CID count) is always X or X+1 if FCoE
* L2 queue is supported. The cid for the FCoE L2 queue is always X.
*/
However this driver also supports NICs that use the E2 controller which can
handle more queues due to having more FP-SB represented by FP_SB_MAX_E2.
Looking at the commits when the E2 support was added, it was originally
using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support").
Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver
was later updated to take full advantage of the E2 instead of having it be
limited to the capabilities of the E1x. But as far as we can tell, the
array "stats_query_entry query" was still limited to using the FP-SB
available to the E1x cards as part of an oversignt when the driver was
updated to take full advantage of the E2, and now with the driver being
aware of the greater queue size supported by E2 NICs, it causes the UBSAN
warnings seen in the stack traces below.
This patch increases the size of the "stats_query_entry query" array by
replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle
both types of NICs.
Stack traces:
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11
index 20 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2e1/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1546:11
index 28 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2fd/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1895:8
index 29 is out of range for type 'stats_query_entry [19]'
CPU: 13 PID: 163 Comm: kworker/u96:1 Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Workqueue: bnx2x bnx2x_sp_task [bnx2x]
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_iov_adjust_stats_req+0x3c4/0x3d0 [bnx2x]
bnx2x_storm_stats_post.part.0+0x4a/0x330 [bnx2x]
? bnx2x_hw_stats_post+0x231/0x250 [bnx2x]
bnx2x_stats_start+0x44/0x70 [bnx2x]
bnx2x_stats_handle+0x149/0x350 [bnx2x]
bnx2x_attn_int_asserted+0x998/0x9b0 [bnx2x]
bnx2x_sp_task+0x491/0x5c0 [bnx2x]
process_one_work+0x18d/0x3f0
</TASK>
---[ end trace ]---
Fixes: 50f0a562f8cc ("bnx2x: add fcoe statistics")
Signed-off-by: Ghadi Elie Rahme <ghadi.rahme@canonical.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20240627111405.1037812-1-ghadi.rahme@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
function
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
mcp251xfd_chip_start/stop()
The mcp251xfd wakes up from Low Power or Sleep Mode when SPI activity
is detected. To avoid this, make sure that the timestamp worker is
stopped before shutting down the chip.
Split the starting of the timestamp worker out of
mcp251xfd_timestamp_init() into the separate function
mcp251xfd_timestamp_start().
Call mcp251xfd_timestamp_init() before mcp251xfd_chip_start(), move
mcp251xfd_timestamp_start() to mcp251xfd_chip_start(). In this way,
mcp251xfd_timestamp_stop() can be called unconditionally by
mcp251xfd_chip_stop().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since the errata references have been added to the driver, new errata
sheets have been published. Update the references for the mcp2517fd
and mcp2518fd. For completeness add references for the mcp251863.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
To fix the coding style, remove the whitespace in front of labels.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Allocate and initialize struct ice_adapter object only once per physical
card instead of once per port. This is not a big deal by now, but we want
to extend this struct more and more in the near future. Our plans include
PTP stuff and a devlink instance representing whole-device/physical card.
Transactions requiring to be sleep-able (like those doing user (here ice)
memory allocation) must be performed with an additional (on top of xarray)
mutex. Adding it here removes need to xa_lock() manually.
Since this commit is a reimplementation of ice_adapter_get(), a rather new
scoped_guard() wrapper for locking is used to simplify the logic.
It's worth to mention that xa_insert() use gives us both slot reservation
and checks if it is already filled, what simplifies code a tiny bit.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Admin queue command for shutdown AQ contains a flag to indicate driver
unload. However, the flag is always set in the driver, even for resets. It
can cause the firmware to consider driver as unloaded once the PF reset is
triggered on all ports of device, which could lead to unexpected results.
Add an additional function parameter to functions that shutdown AQ,
indicating whether the driver is actually unloading.
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Allow the driver to be compatible with different FW API versions based
on the device's MAC type. Currently, E810 is only compatible with one
FW API version. Now the driver can be compatible with different FW API
versions for both E810 and E830. For example, E810 FW API version is
1.5.0 and E830 is 1.7.0.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Check the return value from ice_vsi_rebuild() and prevent the usage of
incorrectly configured VSI.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
