| Age | Commit message (Collapse) | Author |
|---|
|
In QCN9274, RX packet's multicast and broadcast(MCBC) flag is fetched
from RX descriptor's msdu_end info5 member but it is not correct
for QCN9274. Due to this with encryption, ARP request packet is wrongly
marked as MCBC packet and it is sent to mac80211 without setting
RX_FLAG_PN_VALIDATED & RX_FLAG_DECRYPTED flag. This results in packet
getting dropped in mac80211. Hence ping initiated from station to AP
fails.
Fix this by fetching correct MCBC flag in case of QCN9274.
For QC9274 MCBC flag should be fetched from RX descriptor's mpdu_start
info6 member.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 8f04852e90cb ("wifi: ath12k: Use msdu_end to check MCBC")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-5-quic_rajkbhag@quicinc.com
|
|
Add support to process WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT
service bit. If this service bit is set by firmware, then it expects
host to set rx_peer_meta_data_ver in wmi_resource_config's flags2
with value 3 for QCN9274 to indicate as V1B meta version. If this is
not set firmware crash is seen during peer addition.
Hence, if WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT service bit
is set by firmware, set correct peer metadata version to avoid
firmware crash.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-4-quic_rajkbhag@quicinc.com
|
|
Currently while fetching for pdev id from WMI_SERVICE_READY_EXT_EVENTID
we consider 32 bit pdev_id in ath12k_wmi_caps_ext_params structure. But
Firmware sends lower 16 bit for pdev id along with higher 16 bit for
hw_link_id. Due to this wrong pdev id is fetched. This wrong pdev id
when used for WMI commands leads to Firmware crash.
Hence fetch the correct pdev id considering only the lower 16 bits.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-3-quic_rajkbhag@quicinc.com
|
|
When any VDEV is started, MBSSID flags are passed to firmware to
indicate if its a MBSSID/EMA AP vdev. If the interface is not an AP
or if the AP doesn't support MBSSID, the vdev needs to be brought up
as a non MBSSID vdev. Set these flags as a non MBSSID AP by default
which can be updated as and when MBSSID support is added in ath12k.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-2-quic_rajkbhag@quicinc.com
|
|
PCI device IDs of RVU device IDs are configurable and
RVU PF0's (ie AF's) are currently assumed as VFs that
identify loopback functionality ie LBKVFs. But in some
cases these VFs can be setup for different functionality.
Hence remove assumptions that AF's VFs are always LBK VFs
by renaming 'is_afvf' as 'is_lbkvf' explicitly and also
identify LBK VF using PCI dev ID. Similar change is done
for other VF types.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In current driver 64 BPIDs are reserved for LBK interfaces.
These bpids are 1-to-1 mapped to LBK interface channel numbers.
In some usecases one LBK interface required more than one
bpids and in some case they may not require at all.
These usescase can't be address with the current implementation
as it always reserves only one bpid per LBK channel.
This patch addresses this issue by creating free bpid pool from these
64 bpids instead of 1-to-1 mapping to the lbk channel.
Now based on usecase LBK interface can request a bpid using (bp_enable()).
This patch also reduces the number of bpids for cgx interfaces to 8
and adds proper error code
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.
The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.
Currently ath12k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath12k driver and provide the amss.bin
firmware data and size to MHI using a pointer.
Currently enum ath12k_fw_features is empty, the patches adding features will
add the flags.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123122812.3811251-1-quic_rajkbhag@quicinc.com
|
|
WMI_PEER_ASSOC_CMDID
Currently when connecting to an AP with 11AX-HE phy mode, host sends
WMI_VDEV_PARAM_SET_HEMU_MODE parameter to firmware after
WMI_PEER_ASSOC_CMDID command. This results in TXBF not working, because
firmware calculates TXBF values while handling WMI_PEER_ASSOC_CMDID,
however at that time WMI_VDEV_PARAM_SET_HEMU_MODE has not been sent yet.
See below log:
AP sends "VHT/HE/EHT NDP Announcement" to station, and station sends
"Action no Ack" of category code HE to AP, the "Nc Index" and
"Codebook Information" are wrong:
Issued action:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 152
HE MIMO Control: 0x0004008018
.... .... .... .... .... .... .... .... .... .000 = Nc Index: 1 Column (0)
.... .... .... .... .... .... .... ..0. .... .... = Codebook Information: 0
Change to send WMI_VDEV_PARAM_SET_HEMU_MODE before WMI_PEER_ASSOC_CMDID,
then firmware will calculate the TXBF values with valid parameters
instead of empty values. TXBF works well and throughput performance is
improved from 80 Mbps to 130 Mbps with this patch.
Good action after this patch:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 409
HE MIMO Control: 0x0004008219
.... .... .... .... .... .... .... .... .... .001 = Nc Index: 2 Columns (1)
.... .... .... .... .... .... .... ..1. .... .... = Codebook Information: 1
This change applies to all chipsets.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 38dfe775d0ab ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240131021832.17298-1-quic_bqiang@quicinc.com
|
|
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit:
8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()).
Link: https://lore.kernel.org/r/ed1d2c66-1193-4c81-9542-d514c29ba8b8.bugreport@ubisectech.com
Fixes: 8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240126140218.1033443-1-toke@toke.dk
|
|
The variable ret is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so ret can be
removed.
Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the
enclosing expression, the value is never actually read from
'ret' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240116155452.2315351-1-colin.i.king@gmail.com
|
|
Add the led_polarity_set callback for setting LED polarity.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IPQ4019 MDIO internally divide the clock feed by AHB based on the
MDIO_MODE reg. On reset or power up, the default value for the
divider is 0xff that reflect the divider set to /256.
This makes the MDC run at a very low rate, that is, considering AHB is
always fixed to 100Mhz, a value of 390KHz.
This hasn't have been a problem as MDIO wasn't used for time sensitive
operation, it is now that on IPQ807x is usually mounted with PHY that
requires MDIO to load their firmware (example Aquantia PHY).
To handle this problem and permit to set the correct designed MDC
frequency for the SoC add support for the standard "clock-frequency"
property for the MDIO node.
The divider supports value from /1 to /256 and the common value are to
set it to /16 to reflect 6.25Mhz or to /8 on newer platform to reflect
12.5Mhz.
To scan if the requested rate is supported by the divider, loop with
each supported divider and stop when the requested rate match the final
rate with the current divider. An error is returned if the rate doesn't
match any value.
On MDIO reset, the divider is restored to the requested value to prevent
any kind of downclocking caused by the divider reverting to a default
value.
To follow 802.3 spec of 2.5MHz of default value, if divider is set at
/256 and "clock-frequency" is not set in DT, assume nobody set the
divider and try to find the closest MDC rate to 2.5MHz. (in the case of
AHB set to 100MHz, it's 1.5625MHz)
While at is also document other bits of the MDIO_MODE reg to have a
clear idea of what is actually applied there.
Documentation of some BITs is skipped as they are marked as reserved and
their usage is not clear (RES 11:9 GENPHY 16:13 RES1 19:17)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All ipa_power_modem_queue_wake() does is call netif_wake_queue()
on the modem netdev. There is no need to wrap that call in a
trivial function (and certainly not one defined in "ipa_power.c").
So get rid of ipa_power_modem_queue_wake(), and replace its one
caller with a direct call to netif_wake_queue(). Determine the
netdev pointer to use from the private TX endpoint's netdev pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-8-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All ipa_power_modem_queue_active() does now is call netif_wake_queue().
Just call netif_wake_queue() in the two places it's needed, and get
rid of ipa_power_modem_queue_active().
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-7-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All ipa_power_modem_queue_stop() does now is call netif_stop_queue().
Just call netif_stop_queue() in the one place it's needed, and get
rid of ipa_power_modem_queue_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-6-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the STOPPED IPA power flag is used to indicate that the
transmit queue has been stopped. Previously this was used to avoid
setting the STARTED flag unless the queue had already been stopped.
It meant transmit queuing would be enabled on resume if it was
stopped by the transmit path--and if so, it ensured it only got
enabled once.
We only stop the transmit queue in the transmit path. The STARTED
flag has been removed, and it causes no real harm to enable
transmits when they're already enabled. So we can get rid of
the STOPPED flag and call netif_wake_queue() unconditionally.
This makes the IPA power spinlock unnecessary, so it can be removed
as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-5-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A transmit on the modem netdev can only complete if the IPA hardware
is powered. Currently, if a transmit request arrives when the
hardware was not powered, further transmits are be stopped to allow
power-up to complete. Once power-up completes, transmits are once
again enabled.
Runtime resume can complete at the same time a transmit request is
being handled, and previously there was a race between stopping and
restarting transmits. The STARTED flag was used to ensure the
stop request in the transmit path was skipped if the start request
in the runtime resume path had already occurred.
Now, the queue is *always* stopped in the transmit path, *before*
determining whether power is ACTIVE. If power is found to already
be active (or if the socket buffer is gets dropped), transmit is
re-enabled. Otherwise it will (always) be enabled after runtime
resume completes.
The race between transmit and runtime resume no longer exists, so
there is no longer any need to maintain the STARTED flag.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-4-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are a number of flags used in the IPA driver to attempt to
manage race conditions that can occur between runtime resume and
netdev transmit. If we disable TX before requesting power, we can
avoid these races entirely, simplifying things considerably.
This patch implements the main change, disabling transmit always in
the net_device->ndo_start_xmit() callback, then re-enabling it again
whenever we find power is active (or when we drop the skb).
The patches that follow will refactor the "old" code to the point
that most of it can be eliminated.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-3-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than repeatedly looking up the endpoints in the name map,
save the modem TX and RX endpoint pointers in the netdev private
area.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240130192305.250915-2-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the arm random config file, kconfig option 'CONFIG_AEABI' is
disabled which results in adding the compiler flag '-mabi=apcs-gnu'.
This causes the compiler to add padding in virtchnl2_ptype
structure to align it to 8 bytes, resulting in the following
size check failure:
include/linux/build_bug.h:78:41: error: static assertion failed: "(6) == sizeof(struct virtchnl2_ptype)"
78 | #define __static_assert(expr, msg, ...) _Static_assert(expr, msg)
| ^~~~~~~~~~~~~~
include/linux/build_bug.h:77:34: note: in expansion of macro '__static_assert'
77 | #define static_assert(expr, ...) __static_assert(expr, ##__VA_ARGS__, #expr)
| ^~~~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:26:9: note: in expansion of macro 'static_assert'
26 | static_assert((n) == sizeof(struct X))
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:982:1: note: in expansion of macro 'VIRTCHNL2_CHECK_STRUCT_LEN'
982 | VIRTCHNL2_CHECK_STRUCT_LEN(6, virtchnl2_ptype);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid the compiler padding by using "__packed" structure
attribute for the virtchnl2_ptype struct. Also align the
structure by using "__aligned(2)" for better code optimization.
Fixes: 0d7502a9b4a7 ("virtchnl: add virtchnl version 2 ops")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312220250.ufEm8doQ-lkp@intel.com
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240131222241.2087516-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
Call trace:
[ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002
[ 654.568030] Call Trace:
[ 654.571221] <TASK>
[ 654.573790] __schedule+0x2d6/0x960
[ 654.577733] schedule+0x69/0xf0
[ 654.581214] schedule_timeout+0x87/0x140
[ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20
[ 654.590291] msleep+0x2d/0x40
[ 654.593625] napi_disable+0x2b/0x80
[ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc]
[ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc]
[ 654.611101] ? do_wait_intr+0xb0/0xb0
[ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc]
[ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus]
Cc: stable@vger.kernel.org
Fixes: ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1706686551-28510-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Invoking the make_tx_response() / push_tx_responses() pair with no lock
held would be acceptable only if all such invocations happened from the
same context (NAPI instance or dealloc thread). Since this isn't the
case, and since the interface "spec" also doesn't demand that multicast
operations may only be performed with no in-flight transmits,
MCAST_{ADD,DEL} processing also needs to acquire the response lock
around the invocations.
To prevent similar mistakes going forward, "downgrade" the present
functions to private helpers of just the two remaining ones using them
directly, with no forward declarations anymore. This involves renaming
what so far was make_tx_response(), for the new function of that name
to serve the new (wrapper) purpose.
While there,
- constify the txp parameters,
- correct xenvif_idx_release()'s status parameter's type,
- rename {,_}make_tx_response()'s status parameters for consistency with
xenvif_idx_release()'s.
Fixes: 210c34dcd8d9 ("xen-netback: add support for multicast control")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fill-up the lock status error value properly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pass additional argunent status_error over lock_status_get()
so drivers can fill it up. In case they do, expose the value over
previously introduced attribute to user. Do it only in case the
current lock_status is either "unlocked" or "holdover".
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
XDP queues are created/destroyed when a XDP program
is attached/detached. In current driver xdp_queues are not
getting destroyed on program exit due to incorrect xdp_queue
and tot_tx_queue count values.
This patch fixes the issue by setting tot_tx_queue and xdp_queue
count to correct values. It also fixes xdp.data_hard_start address.
Fixes: 06059a1a9a4a ("octeontx2-pf: Add XDP support to netdev PF")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240130120610.16673-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch reduces some of the lines by removing newlines
where more variables or print strings can be pushed back
to the previous line while still adhering to the styling
guidelines.
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fail queue size calculation when the device returns maximum
TX/RX queue sizes that are smaller than the allowed minimum.
Signed-off-by: Osama Abboud <osamaabb@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The netif_* functions are used by the driver to log events into the
kernel ring (dmesg) similar to the netdev_* ones. Unlike the latter,
the netif_* function family allow the user to choose what events get
logged using ethtool:
sudo ethtool -s [interface] msglvl [msg_type] on
By default the events which get logged are slow-path related and aren't
printed often (e.g. interface up related prints). This patch removes the
NETIF_MSG_TX_DONE type (called every TX completion polling) from the
defaults and adds NETIF_MSG_IFDOWN instead as it makes more sensible
defaults.
This patch also transforms ena_down() print from netif_info into
netif_dbg (same as the analogue print in ena_up()) as it suits it
better.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move skb_tx_timestamp() closer to the actual time the driver sends the
packets to the device.
Signed-off-by: Osama Abboud <osamaabb@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The function responsible for polling TX completions might not receive
the CPU resources it needs due to higher priority tasks running on the
requested core.
The driver might not be able to recognize such cases, but it can use its
state to suspect that they happened. If both conditions are met:
- napi hasn't been executed more than the TX completion timeout value
- napi is scheduled (meaning that we've received an interrupt)
Then it's more likely that the napi handler isn't scheduled because of
an overloaded CPU.
It was decided that for this case, the driver would wait twice as long
as the regular timeout before scheduling a reset.
The driver uses ENA_REGS_RESET_SUSPECTED_POLL_STARVATION reset reason to
indicate this case to the device.
This patch also adds more information to the ena_tx_timeout() callback.
This function is called by the kernel when it detects that a specific TX
queue has been closed for too long.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The print was re-worded to a more informative one.
Signed-off-by: Shahar Itzko <itzko@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The functionality was added to allow the drivers to create an
SQ and CQ of different sizes.
When the RX/TX SQ and CQ have the same size, such update isn't
necessary as the device can safely assume it doesn't override
unprocessed completions. However, if the SQ is larger than the CQ,
the device might "have" more completions it wants to update about
than there's room in the CQ.
There's no support for different SQ and CQ sizes, therefore,
removing the API and its usage.
'____cacheline_aligned' compiler attribute was added to
'struct ena_com_io_cq' to ensure that the removal of the
'cq_head_db_reg' field doesn't change the cache-line layout
of this struct.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Dynamic Interrupt Moderation (DIM) is a technique
designed to balance the need for timely data processing
with the desire to minimize CPU overhead.
Instead of generating an interrupt for every received
packet, the system can dynamically adjust the rate at
which interrupts are generated based on the incoming
traffic patterns.
Enabling DIM by default to improve the user experience.
DIM can be turned on/off through ethtool:
`ethtool -C <interface> adaptive-rx <on/off>`
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Osama Abboud <osamaabb@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A few changes for better readability and style
1. Adding / Removing newlines
2. Removing an unnecessary and confusing comment
3. Using an existing variable rather than re-checking a field
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove io_sq->header_addr field because it is no longer
in use.
LLQ was updated to support a bounce buffer so there is
no need in saving the header address of the sq.
Signed-off-by: Nati Koler <nkoler@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Existing MANA design assigns IRQ to every CPU, including sibling
hyper-threads. This may cause multiple IRQs to be active simultaneously
in the same core and may reduce the network performance.
Improve the performance by assigning IRQ to non sibling CPUs in local
NUMA node. The performance improvement we are getting using ntttcp with
following patch is around 15 percent against existing design and
approximately 11 percent, when trying to assign one IRQ in each core
across NUMA nodes, if enough cores are present.
The change will improve the performance for the system
with high number of CPU, where number of CPUs in a node is more than
64 CPUs. Nodes with 64 CPUs or less than 64 CPUs will not be affected
by this change.
The performance study was done using ntttcp tool in Azure.
The node had 2 nodes with 32 cores each, total 128 vCPU and number of channels
were 32 for 32 RX rings.
The below table shows a comparison between existing design and new
design:
IRQ node-num core-num CPU performance(%)
1 0 | 0 0 | 0 0 | 0-1 0
2 0 | 0 0 | 1 1 | 2-3 3
3 0 | 0 1 | 2 2 | 4-5 10
4 0 | 0 1 | 3 3 | 6-7 15
5 0 | 0 2 | 4 4 | 8-9 15
...
...
25 0 | 0 12| 24 24| 48-49 12
...
32 0 | 0 15| 31 31| 62-63 12
33 0 | 0 16| 0 32| 0-1 10
...
64 0 | 0 31| 31 63| 62-63 0
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Souradeep investigated that the driver performs faster if IRQs are
spread on CPUs with the following heuristics:
1. No more than one IRQ per CPU, if possible;
2. NUMA locality is the second priority;
3. Sibling dislocality is the last priority.
Let's consider this topology:
Node 0 1
Core 0 1 2 3
CPU 0 1 2 3 4 5 6 7
The most performant IRQ distribution based on the above topology
and heuristics may look like this:
IRQ Nodes Cores CPUs
0 1 0 0-1
1 1 1 2-3
2 1 0 0-1
3 1 1 2-3
4 2 2 4-5
5 2 3 6-7
6 2 2 4-5
7 2 3 6-7
The irq_setup() routine introduced in this patch leverages the
for_each_numa_hop_mask() iterator and assigns IRQs to sibling groups
as described above.
According to [1], for NUMA-aware but sibling-ignorant IRQ distribution
based on cpumask_local_spread() performance test results look like this:
./ntttcp -r -m 16
NTTTCP for Linux 1.4.0
---------------------------------------------------------
08:05:20 INFO: 17 threads created
08:05:28 INFO: Network activity progressing...
08:06:28 INFO: Test run completed.
08:06:28 INFO: Test cycle finished.
08:06:28 INFO: ##### Totals: #####
08:06:28 INFO: test duration :60.00 seconds
08:06:28 INFO: total bytes :630292053310
08:06:28 INFO: throughput :84.04Gbps
08:06:28 INFO: retrans segs :4
08:06:28 INFO: cpu cores :192
08:06:28 INFO: cpu speed :3799.725MHz
08:06:28 INFO: user :0.05%
08:06:28 INFO: system :1.60%
08:06:28 INFO: idle :96.41%
08:06:28 INFO: iowait :0.00%
08:06:28 INFO: softirq :1.94%
08:06:28 INFO: cycles/byte :2.50
08:06:28 INFO: cpu busy (all) :534.41%
For NUMA- and sibling-aware IRQ distribution, the same test works
15% faster:
./ntttcp -r -m 16
NTTTCP for Linux 1.4.0
---------------------------------------------------------
08:08:51 INFO: 17 threads created
08:08:56 INFO: Network activity progressing...
08:09:56 INFO: Test run completed.
08:09:56 INFO: Test cycle finished.
08:09:56 INFO: ##### Totals: #####
08:09:56 INFO: test duration :60.00 seconds
08:09:56 INFO: total bytes :741966608384
08:09:56 INFO: throughput :98.93Gbps
08:09:56 INFO: retrans segs :6
08:09:56 INFO: cpu cores :192
08:09:56 INFO: cpu speed :3799.791MHz
08:09:56 INFO: user :0.06%
08:09:56 INFO: system :1.81%
08:09:56 INFO: idle :96.18%
08:09:56 INFO: iowait :0.00%
08:09:56 INFO: softirq :1.95%
08:09:56 INFO: cycles/byte :2.25
08:09:56 INFO: cpu busy (all) :569.22%
[1] https://lore.kernel.org/all/20231211063726.GA4977@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net/
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Co-developed-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The first parameter of WARN_ONCE() is a condition so this code will end
up printing the function name instead of the proper message.
Fixes: 3ff7a05996f9 ("wifi: rtl8xxxu: support setting bssid register for multiple interfaces")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/7b144531-a8da-4725-8911-9b614a525a35@moroto.mountain
|
|
To support multi-links beacon, it needs more fields. But currently we still
only support legacy AP mode. Only update struct to fit expected size of
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-8-pkshih@realtek.com
|
|
The ps_state register is used for driver to check if the WiFi chip leave
power save mode successfully. The register is changed for new generation,
so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-7-pkshih@realtek.com
|
|
Because 802.11be chip support MLO mode, driver needs to send new H2C to
pass more connected channel information to firmware, to ensure PS mode
work fine.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-6-pkshih@realtek.com
|
|
This adds support for hardware scan after FW version 0.34.35. Currently
we only support scanning on single hardware band and support of dual band
scan will be added in the future. Adjust the current flow to make driver
compatible with different generation ICs.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-5-pkshih@realtek.com
|
|
The channel field slightly differs between WiFi 6 and WiFi 7.
So we prepare some required functions in advance, this doesn't change
existing wifi 6 ICs behavior. This H2C prepares the channel list
to be scanned for. With layout as the following:
+--------+--------------------+-------------------+-----------------------+
| header | number of channels | channel info size | channel_info * number |
+--------+--------------------+-------------------+-----------------------+
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-4-pkshih@realtek.com
|
|
This allows scan related logs when FW log debug mode is on.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-3-pkshih@realtek.com
|
|
Add definition and parsing for wifi 7 extended fields. These fields
include hardware index which is current reporting, timestamp and self
defined sequences for debug purposes.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126063356.17857-2-pkshih@realtek.com
|
|
The chip_ops::fem_setup is to get if a hardware module type contains PA
and LNA that will affect how RF calibrations do. The chip_ops::rfe_gpio
is to set GPIO PIN MUX according to hardware module type too. 8922A
doesn't have these special module types yet, so leave them as NULL.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033813.12562-1-pkshih@realtek.com
|
|
Get thermal value as a clue to do RF calibration if the delta is larger
than a threshold, but 8922A doesn't need this, so we only read out the
value when debugging to reduce IO.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033802.12508-1-pkshih@realtek.com
|
|
Implement indirect interface v2 to read/write RF registers via PHY
registers for 8922A.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240124033637.12330-5-pkshih@realtek.com
|
