| Age | Commit message (Collapse) | Author |
|---|
|
Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There're two identical entries for ax1650 device in
iwl_dev_info_table. Remove one of the duplicate entries.
Fixes: 953e66a7238b ("iwlwifi: add new ax1650 killer device")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230410140721.897683-2-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Host commands and notifications are expected to be ordered in
iwl_mvm_groups array. Fix the order of two new TIMING_MEASUREMENT
notifications.
Fixes: c7eca79def44 ("wifi: iwlwifi: mvm: report hardware timestamps in RX/TX status")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/linux-wireless/20230331175121.GA3127046@dev-arch.thelio-3990X/
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230410140721.897683-1-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
No functional modification involved.
drivers/net/fddi/skfp/rmt.c:236 rmt_fsm() warn: if statement not indented.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4736
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230407034157.61276-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
n_addr is used to store be32 values,
so a sparse-friendly array of be32 to store these values.
Flagged by sparse:
.../mtk_ppe_debugfs.c:59:27: warning: incorrect type in assignment (different base types)
.../mtk_ppe_debugfs.c:59:27: expected unsigned int
.../mtk_ppe_debugfs.c:59:27: got restricted __be32 [usertype]
.../mtk_ppe_debugfs.c:161:46: warning: cast to restricted __be16
No functional changes intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230401-mtk_eth_soc-sparse-v2-1-963becba3cb7@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drivers call netdev_tx_completed_queue() right before
netif_txq_maybe_wake(). If BQL is enabled netdev_tx_completed_queue()
should issue a memory barrier, so we can depend on that separating
the stop check from the consumer index update, instead of adding
another barrier in netif_txq_maybe_wake().
This matters more than the barriers on the xmit path, because
the wake condition is almost always true. So we issue the
consumer side barrier often.
Wrap netdev_tx_completed_queue() in a local helper to issue
the barrier even if BQL is disabled. Keep the same semantics
as netdev_tx_completed_queue() (barrier only if bytes != 0)
to make it clear that the barrier is conditional.
Plus since macro gets pkt/byte counts as arguments now -
we can skip waking if there were no packets completed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert bnxt to use new macros rather than open code the logic.
Two differences:
(1) bnxt_tx_int() will now only issue a memory barrier if it sees
enough space on the ring to wake the queue. This should be fine,
the mb() is between the writes to the ring pointers and checking
queue state.
(2) we'll start the queue instead of waking on race, this should
be safe inside the xmit handler.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert ixgbe to use the new macros, I think a lot of people
copy the ixgbe code. The only functional change is that the
unlikely() in ixgbe_clean_tx_irq() turns into a likely()
inside the new macro and no longer includes
total_packets && netif_carrier_ok(tx_ring->netdev)
which is probably for the best, anyway.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230407145911.79642-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230407145911.79642-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If SFP module is not present, it is sensible to fail sfp_module_eeprom()
and sfp_module_eeprom_by_page() early to avoid excessive I2C transfers
which are garanteed to fail.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.
One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.
# ethtool -m xge0
i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
Cannot get Module EEPROM data: Operation not supported
If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error
# ethtool -m xge0
Cannot get Module EEPROM data: Remote I/O error
Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When memory is a little tight on my system, it's pretty easy to see
warnings that look like this.
ksoftirqd/0: page allocation failure: order:3, mode:0x40a20(GFP_ATOMIC|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
...
Call trace:
dump_backtrace+0x0/0x1e8
show_stack+0x20/0x2c
dump_stack_lvl+0x60/0x78
dump_stack+0x18/0x38
warn_alloc+0x104/0x174
__alloc_pages+0x588/0x67c
alloc_rx_agg+0xa0/0x190 [r8152 ...]
r8152_poll+0x270/0x760 [r8152 ...]
__napi_poll+0x44/0x1ec
net_rx_action+0x100/0x300
__do_softirq+0xec/0x38c
run_ksoftirqd+0x38/0xec
smpboot_thread_fn+0xb8/0x248
kthread+0x134/0x154
ret_from_fork+0x10/0x20
On a fragmented system it's normal that order 3 allocations will
sometimes fail, especially atomic ones. The driver handles these
failures fine and the WARN just creates spam in the logs for this
case. The __GFP_NOWARN flag is exactly for this situation, so add it
to the allocation.
NOTE: my testing is on a 5.15 system, but there should be no reason
that this would be fundamentally different on a mainline kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230406171411.1.I84dbef45786af440fd269b71e9436a96a8e7a152@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
anarion_config_dt()
Always return struct anarion_gmac * from anarion_config_dt().
In the case where ctl_block was an error pointer it was being
returned directly. Which sparse flags as follows:
.../dwmac-anarion.c:73:24: warning: incorrect type in return expression (different address spaces)
.../dwmac-anarion.c:73:24: expected struct anarion_gmac *
.../dwmac-anarion.c:73:24: got void [noderef] __iomem *[assigned] ctl_block
Avoid this by converting the error pointer to an error.
And then reversing the conversion.
As a side effect, the error can be used for logging purposes,
subjectively, leading to a minor cleanup.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use __iomem annotation the register base: the ctl_block field of struct
anarion_gmac. I believe this is the normal practice for such variables.
By doing so some casting is avoided.
And sparse no longer reports:
.../dwmac-anarion.c:29:23: warning: incorrect type in argument 1 (different address spaces)
.../dwmac-anarion.c:29:23: expected void const volatile [noderef] __iomem *addr
.../dwmac-anarion.c:29:23: got void *
.../dwmac-anarion.c:34:22: warning: incorrect type in argument 2 (different address spaces)
.../dwmac-anarion.c:34:22: expected void volatile [noderef] __iomem *addr
.../dwmac-anarion.c:34:22: got void *
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This was never used since the commit that added it - e58bb43f5e43
("stmmac: initial support to manage pcs modes").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230406125412.48790-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Leon Romanovsky says:
====================
Improve IPsec limits, ESN and replay window
This series overcomes existing hardware limitations in Mellanox ConnectX
devices around handling IPsec soft and hard limits.
In addition, the ESN logic is tied and added an interface to configure
replay window sequence numbers through existing iproute2 interface.
ip xfrm state ... [ replay-seq SEQ ] [ replay-oseq SEQ ]
[ replay-seq-hi SEQ ] [ replay-oseq-hi SEQ ]
Link: https://lore.kernel.org/all/cover.1680162300.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
* tag 'ipsec-esn-replay' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Simulate missing IPsec TX limits hardware functionality
net/mlx5e: Generalize IPsec work structs
net/mlx5e: Reduce contention in IPsec workqueue
net/mlx5e: Set IPsec replay sequence numbers
net/mlx5e: Remove ESN callbacks if it is not supported
xfrm: don't require advance ESN callback for packet offload
net/mlx5e: Overcome slow response for first IPsec ASO WQE
net/mlx5e: Add SW implementation to support IPsec 64 bit soft and hard limits
net/mlx5e: Prevent zero IPsec soft/hard limits
net/mlx5e: Factor out IPsec ASO update function
====================
Link: https://lore.kernel.org/r/20230406071902.712388-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Any multiplication between GENMASK(31, 0) and a number bigger than 1
will be truncated because of the overflow, if the size of unsigned long
is 32 bits.
Replaced GENMASK with GENMASK_ULL to make sure that multiplication will
be between 64 bits values.
Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095953.75622-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TI's J784S4 SoC supports USXGMII mode. Add USXGMII mode to the
extra_modes member of the J784S4 SoC data.
Configure MAC control register for supporting USXGMII mode and add
MAC_5000FD in the "mac_capabilities" member of struct "phylink_config".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TI's J784S4 SoC supports QSGMII mode with the CPSW9G instance of the
CPSW Ethernet Switch. Add a new compatible for J784S4 SoC and enable
QSGMII support for it by adding QSGMII mode to the extra_modes member of
the "j784s4_cpswxg_pdata" SoC data.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the interface mode specific configuration to the mac_config()
callback am65_cpsw_nuss_mac_config().
Also, do not reset the MAC Control register on mac_link_down(). Only
clear those bits that can possibly be set in mac_link_up().
Let the MAC remain in IDLE state after mac_link_down(). Bring it out of
the IDLE state on mac_link_up().
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.
However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.
Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.
Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a device is roaming between interfaces and a new flow entry is
created, we should assume that its output device is more up to date than
whatever entry existed already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WED version 2 (on MT7986 and later) can offload flows originating from
wireless devices.
In order to make that work, ndo_setup_tc needs to be implemented on the
netdevs. This adds the required code to offload flows coming in from WED,
while keeping track of the incoming wed index used for selecting the
correct PPE device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Smatch reports: drivers/net/ethernet/sun/niu.c:4525
niu_alloc_channels() warn: missing unwind goto?
If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.
Fix this by changing direct return to a goto 'out_err'.
Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-04-05
From Paul:
- TC action parsing cleanups
- Correctly report stats for missed packets
- Many CT actions limitations removed due to hw misses will now
continue from the relevant tc ct action in software.
From Adham:
- RQ/SQ devlink health diagnostics layout fixes
From Gal And Rahul:
- PTP code cleanup and cyclecounter shift value improvement
* tag 'mlx5-updates-2023-04-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix SQ SW state layout in SQ devlink health diagnostics
net/mlx5e: Fix RQ SW state layout in RQ devlink health diagnostics
net/mlx5e: Rename misleading skb_pc/cc references in ptp code
net/mlx5: Update cyclecounter shift value to improve ptp free running mode precision
net/mlx5e: Remove redundant macsec code
net/mlx5e: TC, Remove sample and ct limitation
net/mlx5e: TC, Remove mirror and ct limitation
net/mlx5e: TC, Remove tuple rewrite and ct limitation
net/mlx5e: TC, Remove multiple ct actions limitation
net/mlx5e: TC, Remove special handling of CT action
net/mlx5e: TC, Remove CT action reordering
net/mlx5e: CT: Use per action stats
net/mlx5e: TC, Move main flow attribute cleanup to helper func
net/mlx5e: TC, Remove unused vf_tun variable
net/mlx5e: Set default can_offload action
====================
Link: https://lore.kernel.org/r/20230406020232.83844-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A recent rearrangement of includes has lead to a problem on m68k
as flagged by the kernel test robot.
Resolve this by moving the block asm includes to below linux includes.
A side effect i that non-Sparc asm includes are now immediately
before Sparc asm includes, which seems nice.
Using sparse v0.6.4 I was able to reproduce this problem as follows
using the config provided by the kernel test robot:
$ wget https://download.01.org/0day-ci/archive/20230404/202304041748.0sQc4K4l-lkp@intel.com/config
$ cp config .config
$ make ARCH=m68k oldconfig
$ make ARCH=m68k C=2 M=drivers/net/ethernet/sun
CC [M] drivers/net/ethernet/sun/sunhme.o
In file included from drivers/net/ethernet/sun/sunhme.c:19:
./arch/m68k/include/asm/irq.h:78:11: error: expected ‘;’ before ‘void’
78 | asmlinkage void do_IRQ(int irq, struct pt_regs *regs);
| ^~~~~
| ;
./arch/m68k/include/asm/irq.h:78:40: warning: ‘struct pt_regs’ declared inside parameter list will not be visible outside of this definition or declaration
78 | asmlinkage void do_IRQ(int irq, struct pt_regs *regs);
| ^~~~~~~
Compile tested only.
Fixes: 1ff4f42aef60 ("net: sunhme: Alphabetize includes")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304041748.0sQc4K4l-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230405-sunhme-includes-fix-v1-1-bf17cc5de20d@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/google/gve/gve.h
3ce934558097 ("gve: Secure enough bytes in the first TX desc for all TCP pkts")
75eaae158b1b ("gve: Add XDP DROP and TX support for GQI-QPL format")
https://lore.kernel.org/all/20230406104927.45d176f5@canb.auug.org.au/
https://lore.kernel.org/all/c5872985-1a95-0bc8-9dcc-b6f23b439e9d@tessares.net/
Adjacent changes:
net/can/isotp.c
051737439eae ("can: isotp: fix race between isotp_sendsmg() and isotp_release()")
96d1c81e6a04 ("can: isotp: add module parameter for maximum pdu size")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes: fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shahab Vahedi <shahab@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`dev_port` is used to differentiate devices that instantiate from
the same function, which is the case in most of NFP NICs.
In some customized scenario, `dev_port` is used to rename netdev
instead of `phys_port_name`. Example rules using `dev_port`:
SUBSYSTEM=="net", ACTION=="add", KERNELS=="0000:e1:00.0", ATTR{dev_port}=="0", NAME:="ens8np0"
SUBSYSTEM=="net", ACTION=="add", KERNELS=="0000:e1:00.0", ATTR{dev_port}=="1", NAME:="ens8np1"
To take port split case into account, here we initialize `dev_port`
according to the port sequence in eth_table from management firmware
instead of using port label id directly. And management firmware
makes sure that port sequence matches its label id.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20230405120829.28817-1-louis.peens@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
To handle potential read/write operation failures, update
ksz8_w_sta_mac_table() to make use of the return values provided by
read/write functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since ksz8_w_sta_mac_table() is only used within ksz8795.c, make it static
to limit its scope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
read/write functions
Take advantage of the return values provided by read/write functions in
ksz8_r_sta_mac_table() to handle cases where read/write operations may
fail.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
empty entries
Prepare for the next patch by ensuring that ksz8_r_sta_mac_table() does
not use error codes for empty entries. This change will enable better
handling of read/write errors in the upcoming patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As ksz8_r_sta_mac_table() is only used within ksz8795.c, there is no need
to export it. Make the function static for better encapsulation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
operations
Add support for add/del_fdb operations and utilize the refactored static
MAC table code. This resolves kernel warnings caused by the lack of fdb
add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ConnectX-7 devices don't have ability to send TX hard/soft limits
events. As a possible workaround, let's rely on existing infrastructure
and use periodic check of cached flow counter. In these periodic checks,
we call to xfrm_state_check_expire() to check and mark state accordingly.
Once the state is marked as XFRM_STATE_EXPIRED, the SA flow rule is
changed to drop all the traffic.
Link: https://lore.kernel.org/r/94a5d82c0c399747117d8a558f9beebfbcf26154.1680162300.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
IPsec logic has two work structs which are submitted to same workqueue.
As a preparation to addition of new work which needs to be submitted
too, let's generalize struct mlx5e_ipsec_work.
Link: https://lore.kernel.org/r/285a1550242363de181bab3a07a69296f66ad9a8.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
IPsec workqueue shouldn't be declared as ordered queue with one work
per-CPU, and can be safely changed to be unordered with default number
of works per-CPU.
Link: https://lore.kernel.org/r/5dc224a4decd09c14f645d38173e1a1710802cd8.1680162300.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
"ip xfrm state ..." command allows users to configure replay sequence
numbers with replay-seq* arguments for RX and replay-oseq* for TX.
Add the needed driver logic to support setting them.
Link: https://lore.kernel.org/r/a9b17827eff2b29a4951225efa684a6cd38f74fe.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
There is no need in implementation of .xdo_dev_state_advance_esn() and
setting work as it will never be called in packet offload mode.
Link: https://lore.kernel.org/r/2fc9fade32e31f03b100d6086a82ad36269349dc.1680162300.git.leonro@nvidia.com
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
