| Age | Commit message (Collapse) | Author |
|---|
|
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Fixes: f942dc2552b8 ('xen network backend driver')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab68d ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reported-by: Zheng Wang <zyytlz.wz@163.com>
Closes: https://lore.kernel.org/netdev/20230725030026.1664873-1-zyytlz.wz@163.com/
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ravb_remove(), dma_free_coherent() should be call after
unregister_netdev(). Otherwise, this controller is possible to use
the freed buffer.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The first pull request for v6.7, with both stack and driver changes.
We have a big change how locking is handled in cfg80211 and mac80211
which removes several locks and hopefully simplifies the locking
overall. In drivers rtw89 got MCC support and smaller features to
other active drivers but nothing out of ordinary.
Major changes:
cfg80211
- remove wdev mutex, use the wiphy mutex instead
- annotate iftype_data pointer with sparse
- first kunit tests, for element defrag
- remove unused scan_width support
mac80211
- major locking rework, remove several locks like sta_mtx, key_mtx
etc. and use the wiphy mutex instead
- remove unused shifted rate support
- support antenna control in frame injection (requires driver support)
- convert RX_DROP_UNUSABLE to more detailed reason codes
rtw89
- TDMA-based multi-channel concurrency (MCC) support
iwlwifi
- support set_antenna() operation
- support frame injection antenna control
ath12k
- WCN7850: enable 320 MHz channels in 6 GHz band
- WCN7850: hardware rfkill support
- WCN7850: enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to make scan faster
ath11k
- add chip id board name while searching board-2.bin
* tag 'wireless-next-2023-10-06' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (272 commits)
wifi: rtlwifi: remove unreachable code in rtl92d_dm_check_edca_turbo()
wifi: rtw89: debug: txpwr table supports Wi-Fi 7 chips
wifi: rtw89: debug: show txpwr table according to chip gen
wifi: rtw89: phy: set TX power RU limit according to chip gen
wifi: rtw89: phy: set TX power limit according to chip gen
wifi: rtw89: phy: set TX power offset according to chip gen
wifi: rtw89: phy: set TX power by rate according to chip gen
wifi: rtw89: mac: get TX power control register according to chip gen
wifi: rtlwifi: use unsigned long for rtl_bssid_entry timestamp
wifi: rtlwifi: fix EDCA limit set by BT coexistence
wifi: rt2x00: fix MT7620 low RSSI issue
wifi: rtw89: refine bandwidth 160MHz uplink OFDMA performance
wifi: rtw89: refine uplink trigger based control mechanism
wifi: rtw89: 8851b: update TX power tables to R34
wifi: rtw89: 8852b: update TX power tables to R35
wifi: rtw89: 8852c: update TX power tables to R67
wifi: rtw89: regd: configure Thailand in regulation type
wifi: mac80211: add back SPDX identifier
wifi: mac80211: fix ieee80211_drop_unencrypted_mgmt return type/value
wifi: rtlwifi: cleanup few rtlxxxx_set_hw_reg() routines
...
====================
Link: https://lore.kernel.org/r/87jzrz6bvw.fsf@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds the BCM5221 PHY support by reusing brcm_fet_*()
callbacks and adding quirks for BCM5221 when needed.
Cc: Jim Reinhart <jimr@tekvox.com>
Cc: James Autry <jautry@tekvox.com>
Cc: Matthew Maron <matthewm@tekvox.com>
Signed-off-by: Giulio Benetti <giulio.benetti+tekvox@benettiengineering.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231005182915.153815-1-giulio.benetti@benettiengineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
i40e: House-keeping and clean-up
Ivan Vecera says:
The series makes some house-keeping tasks on i40e driver:
Patch 1: Removes unnecessary back pointer from i40e_hw
Patch 2: Moves I40E_MASK macro to i40e_register.h where is used
Patch 3: Refactors I40E_MDIO_CLAUSE* to use the common macro
Patch 4: Add header dependencies to <linux/avf/virtchnl.h>
Patch 5: Simplifies memory alloction functions
Patch 6: Moves mem alloc structures to i40e_alloc.h
Patch 7: Splits i40e_osdep.h to i40e_debug.h and i40e_io.h
Patch 8: Removes circular header deps, fixes and cleans headers
Patch 9: Moves DDP specific macros and structs to i40e_ddp.c
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: Move DDP specific macros and structures to i40e_ddp.c
i40e: Remove circular header dependencies and fix headers
i40e: Split i40e_osdep.h
i40e: Move memory allocation structures to i40e_alloc.h
i40e: Simplify memory allocation functions
virtchnl: Add header dependencies
i40e: Refactor I40E_MDIO_CLAUSE* macros
i40e: Move I40E_MASK macro to i40e_register.h
i40e: Remove back pointer from i40e_hw structure
====================
Link: https://lore.kernel.org/r/20231005162850.3218594-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect netdev->name to be NUL-terminated based on its use with format
strings and dev_info():
| dev_info(&adapter->pdev->dev,
| "%s link is up %d Mbps %s\n",
| netdev->name, adapter->link_speed,
| adapter->link_duplex == FULL_DUPLEX ?
| "full duplex" : "half duplex");
Furthermore, NUL-padding is not required as netdev is already
zero-initialized through alloc_etherdev().
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231005-strncpy-drivers-net-ethernet-atheros-atlx-atl2-c-v1-1-493f113ebfc7@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`strncpy` is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on the destination buffer without
unnecessarily NUL-padding.
It should be noted that there doesn't currently exist a bug here as
DRV_NAME is a small string literal which means no overread bugs are
present.
Also to note, other ethernet drivers are using strscpy in a similar
pattern:
| dec/tulip/tulip_core.c
| 861: strscpy(info->driver, DRV_NAME, sizeof(info->driver));
|
| 8390/ax88796.c
| 582: strscpy(info->driver, DRV_NAME, sizeof(info->driver));
|
| dec/tulip/dmfe.c
| 1077: strscpy(info->driver, DRV_NAME, sizeof(info->driver));
|
| 8390/etherh.c
| 558: strscpy(info->driver, DRV_NAME, sizeof(info->driver));
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Lukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20231005-strncpy-drivers-net-ethernet-asix-ax88796c_ioctl-c-v1-1-6fafdc38b170@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As we don't specify the MTU in the driver, the framework
will fall back to 1500 bytes and this doesn't work very
well when we try to attach a DSA switch:
eth1: mtu greater than device maximum
ixp4xx_eth c800a000.ethernet eth1: error -22 setting
MTU to 1504 to include DSA overhead
After locating an out-of-tree patch in OpenWrt I found
suitable code to set the MTU on the interface and ported
it and updated it. Now the MTU gets set properly.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231005-ixp4xx-eth-mtu-v4-1-08c66ed0bc69@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-10-05
The first patch is by Miquel Raynal and fixes a comment in the sja1000
driver.
Vincent Mailhol contributes 2 patches that fix W=1 compiler warnings
in the etas_es58x driver.
Jiapeng Chong's patch removes an unneeded NULL pointer check before
dev_put() in the CAN raw protocol.
A patch by Justin Stittreplaces a strncpy() by strscpy() in the
peak_pci sja1000 driver.
The next 5 patches are by me and fix the can_restart() handler and
replace BUG_ON()s in the CAN dev helpers with proper error handling.
The last 27 patches are also by me and target the at91_can driver.
First a new helper function is introduced, the at91_can driver is
cleaned up and updated to use the rx-offload helper.
* tag 'linux-can-next-for-6.7-20231005' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (37 commits)
can: at91_can: switch to rx-offload implementation
can: at91_can: at91_alloc_can_err_skb() introduce new function
can: at91_can: at91_irq_err_line(): send error counters with state change
can: at91_can: at91_irq_err_line(): make use of can_change_state() and can_bus_off()
can: at91_can: at91_irq_err_line(): take reg_sr into account for bus off
can: at91_can: at91_irq_err_line(): make use of can_state_get_by_berr_counter()
can: at91_can: at91_irq_err(): rename to at91_irq_err_line()
can: at91_can: at91_irq_err_frame(): move next to at91_irq_err()
can: at91_can: at91_irq_err_frame(): call directly from IRQ handler
can: at91_can: at91_poll_err(): increase stats even if no quota left or OOM
can: at91_can: at91_poll_err(): fold in at91_poll_err_frame()
can: at91_can: add CAN transceiver support
can: at91_can: at91_open(): forward request_irq()'s return value in case or an error
can: at91_can: at91_chip_start(): don't disable IRQs twice
can: at91_can: at91_set_bittiming(): demote register output to debug level
can: at91_can: rename struct at91_priv::{tx_next,tx_echo} to {tx_head,tx_tail}
can: at91_can: at91_setup_mailboxes(): update comments
can: at91_can: add more register definitions
can: at91_can: MCR Register: convert to FIELD_PREP()
can: at91_can: MSR Register: convert to FIELD_PREP()
...
====================
Link: https://lore.kernel.org/r/20231005195812.549776-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Resolve several conflicts, mostly between changes/fixes in
wireless and the locking rework in wireless-next. One of
the conflicts actually shows a bug in wireless that we'll
want to fix separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix id2_register content for tcan4553. This slipped through my testing.
Reported-by: Sean Anderson <sean.anderson@seco.com>
Closes: https://lore.kernel.org/lkml/a94e6fc8-4f08-7877-2ba0-29b9c2780136@seco.com/
Fixes: 142c6dc6d9d7 ("can: tcan4x5x: Add support for tcan4552/4553")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20230919095401.1312259-1-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.
Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/
Signed-off-by: John Watts <contact@jookia.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20230905231342.2042759-2-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
PHYs via management frames
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit c766e077d927 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
Fixes: c766e077d927 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements the led_hw_* hooks to support hardware blinking LEDs on
the DP83867 phy. The driver supports all LED modes that have a
corresponding TRIGGER_NETDEV_* define. Error and collision do not have
a TRIGGER_NETDEV_* define, so these modes are currently not supported.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patches prepared the code to allow separating between
choosing blocks and filling blocks.
Do not add blocks as part of the loop that chooses them. When all the
required blocks are set in the bitmap 'chosen_blocks_bm', start filling
blocks. Iterate over the bitmap twice - first add only blocks that are
marked with 'high_entropy' flag. Then, fill the rest of the blocks.
The idea is to place key blocks with high entropy in blocks 0 to 5. See
more details in previous patches.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. Currently, the indication of whether all elements were
found in the chosen blocks is by the structure 'key_info->elusage'. This
structure is updated when block is filled as part of
mlxsw_afk_picker_key_info_add(). A following patch will call this
function only after choosing all the blocks. Add a bitmap called
'elusage_chosen' to store which elements were chosen in the chosen blocks.
Change the condition in the loop to check elements that were chosen, not
elements that were already filled in the blocks.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. During the search, the structure 'mlxsw_afk_picker' is
used per block, it contains how many elements from the required list appear
in the block. When a block is chosen and filled, this bitmap of elements is
cleaned. To be able to fill the blocks at the end, add a bitmap called
'chosen_element' as part of picker. When a block is chosen, copy the
'element' bitmap to it. Use the new bitmap as part of
mlxsw_afk_picker_key_info_add(). So later, when filling the block will
be done at the end of the searching, we will use the copied bitmap that
contains the elements that should be used in the block.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, mlxsw_afk_picker() chooses which blocks will be used for a
given list of elements, and fills the blocks during the searching - when a
key block is found with most hits, it adds it and removes the elements from
the count of hits. This should be changed as we want to be able to choose
which blocks will be placed in blocks 0 to 5.
To separate between choosing blocks and filling blocks, several pre-changes
are required. The indexes of the chosen blocks should be saved, so then
the relevant blocks will be filled at the end of search.
Allocate a bitmap for chosen blocks, when a block is found with most
hits, set the relevant bit in the bitmap. This bitmap will be used in a
following patch.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For 12 key blocks in the A-TCAM, rules are split into two records, which
constitute two lookups. The two records are linked using a
"large entry key ID".
Due to a Spectrum-4 hardware issue, KVD entries that correspond to key
blocks 0 to 5 of 12 key blocks A-TCAM entries will be placed in the same
KVD pipe if they only differ in their "large entry key ID", as it is
ignored. This results in a reduced scale. To reduce the probability of this
issue, we can place key blocks with high entropy in blocks 0 to 5. The idea
is to place blocks that are changed often in blocks 0 to 5, for
example, key blocks that match on IPv4 addresses or the LSBs of IPv6
addresses. Such placement will reduce the probability of these blocks to be
same.
Mark several blocks with 'high_entropy' flag, so later we will take into
account this flag and place them in blocks 0 to 5.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a foreign LHS rule (TC rule from a tunnel netdev which requests
conntrack lookup) matches on inner headers or enc_key_id, these matches
cannot be performed by the Outer Rule table, as the keys are only
available after the tunnel type has been identified (by the OR lookup)
and the rest of the headers parsed accordingly.
Offload such rules with an Action Rule, using the LOOKUP_CONTROL section
of the AR response to specify the conntrack and/or recirculation actions,
combined with an Outer Rule which performs only the usual Encap Match
duties.
This processing flow, as it requires two AR lookups per packet, is less
performant than OR-CT-AR, so only use it where necessary.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a few places where no extack error message was set, or the
extack was not forwarded to callees, potentially resulting in a return
of -EOPNOTSUPP with no additional information.
Make sure to populate the error message in these cases. In practice
this does us no good as TC indirect block callbacks don't come with an
extack to fill in; but maybe they will someday and when debugging it's
possible to provide a fake extack and emit its message to the console.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Normally, if a TC filter on a tunnel netdev does not match on any
encap fields, we decline to offload it, as it cannot meet our
requirement for a <sip,dip,dport> tuple for the encap match.
However, if the rule has a nonzero chain_index, then for a packet to
reach the rule, it must already have matched a LHS rule which will
have included an encap match and determined the tunnel type, so in
that case we can offload the right-hand-side rule.
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow a tunnel netdevice (such as a vxlan) to offload conntrack lookups,
in much the same way as efx netdevs.
To ensure this rule does not overlap with other tunnel rules on the same
sip,dip,dport tuple, register a pseudo encap match of a new type
(EFX_TC_EM_PSEUDO_OR), which unlike PSEUDO_MASK may only be referenced
once (because an actual Outer Rule in hardware exists, although its
fw_id is not recorded in the encap match entry).
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct nfp_eth_table.
Cc: Simon Horman <simon.horman@corigine.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Yinjun Zhang <yinjun.zhang@corigine.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Yu Xiao <yu.xiao@corigine.com>
Cc: Sixiang Chen <sixiang.chen@corigine.com>
Cc: oss-drivers@corigine.com
Cc: netdev@vger.kernel.org
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct nfp_reprs.
Cc: Simon Horman <simon.horman@corigine.com>
Cc: oss-drivers@corigine.com
Link: https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20231003231843.work.811-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Improve the Nokia GPON fixup - we need to ignore not only the hardware
LOS signal, but also the software implementation as well. Do this by
using the new state_ignore_mask to indicate that we should ignore not
only the hardware RX_LOS signal, and also clear the LOS bits in the
option field.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/E1qnfXh-008UDe-F9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Re-implement how we ignore the hardware TX_FAULT signal. Rather than
having a separate boolean for this, use a bitmask of the hardware
signals that we wish to ignore. This gives more flexibility in the
future to ignore other signals such as RX_LOS.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/E1qnfXc-008UDY-91@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
AR7 is going to be removed from the Kernel, so remove its networking
support in form of the cpmac driver. This allows us to remove the
platform because this driver includes a platform specific header.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/all/20230922061530.3121-6-wsa+renesas@sang-engineering.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (or adjacent changes of note).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current at91_can driver uses NAPI to handle RX'ed CAN frames, the
RX IRQ is disabled and a NAPI poll is scheduled. Then in
at91_poll_rx() the RX'ed CAN frames are tried to read in order from
the device.
This approach has 2 drawbacks:
- Under high system load it might take too long from the initial RX
IRQ to the NAPI poll function to run. This causes RX buffer
overflows.
- The algorithm to read the CAN frames in order is not bullet proof
and may fail under certain use cases/system loads.
The rx-offload helper fixes these problems by reading the RX'ed CAN
frames in the interrupt handler and adding it to a list sorted by RX
timestamp. This list of RX'ed SKBs is then passed to the networking
stack via NAPI.
Convert the RX path to rx-offload, pass all CAN error frames with
can_rx_offload_queue_timestamp().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-27-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch to convert the driver to make use of the
rx-offload helper. With rx-offload the received CAN frames are sorted
by their timestamp. Regular CAN RX'ed and TX'ed CAN frames are
timestamped by the hardware. Error events are not.
Introduce a new function at91_alloc_can_err_skb() the allocates an
error SKB and reads the current timestamp from the controller.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-26-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since 3e5c291c7942 ("can: add CAN_ERR_CNT flag to notify availability
of error counter") there is a dedicated flag to inform the user space,
that there are CAN error counters in the CAN error frame.
In case the device is not in bus off mode, send the error counters to
user space and set CAN_ERR_CNT.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-25-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_bus_off()
The driver implements a hand crafted CAN state handling. Update the
driver to make use of can_change_state(), introduced in ("can: dev:
Consolidate and unify state change handling")
Also switch from hand crafted CAN bus off handling to can_bus_off():
In case of a bus off, abort all pending TX requests, switch off the
device and let can_bus_off() handle the device restart.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-24-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The at91 CAN controller automatically recovers from bus-off after 128
occurrences of 11 consecutive recessive bits.
After an auto-recovered bus-off, the error counters no longer reflect
this fact. On the sam9263 the state bits in the SR register show the
current state (based on the current error counters), while on sam9x5
and newer SoCs these bits are latched.
Take any latched bus-off information from the SR register into account
when calculating the CAN new state, to start the standard CAN bus off
handling.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-23-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On the sam9263 the SR bits for bus off, error passive, warning limit,
and error active are not latched and reflect the current status of the
controller. On the sam9x5 and newer SoCs these bits are latched.
To simplify the code, use can_state_get_by_berr_counter() to get the
state of the controller regardless of the SoC version.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-22-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a cleanup patch, no functional change intended.
The function at91_irq_err() only handles the CAN line errors, so
rename it accordingly to at91_irq_err_line().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-21-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a cleanup patch, no functional change intended. As
at91_irq_err_frame() is called from the IRQ handler move it in front
of the IRQ handler next to at91_irq_err().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-20-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch to convert the driver to the rx-offload
helper. In rx-offload RX, TX-done and CAN error handling are done in
the IRQ handler, SKB are pushed to the network stack in the NAPI poll
function.
Move the CAN frame error handling from the NAPI function at91_poll()
to the IRQ handler at91_poll(). To reflect this change, rename
at91_poll_err() to at91_irq_err_frame().
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-19-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
at91_poll_err() allocates a can error SKB, to inform the user space
about the CAN error. Then it fills the SKB with information the error
information and increases the net device error stats.
In case no SBK can be allocated (e.g. due to an OOM) or the NAPI quota
is 0 the function is left early and no stats are updated. This is not
helpful to the user, as there is no information about the faulty CAN
bus.
Increase the error stats even if no quota is left or no SKB can be
allocated.
While there treat No-Acknowledgment as a bus error, too.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-18-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch for the cleanup of at91_poll_err(). Fold
at91_poll_err_frame() into at91_poll_err() so that it can be easier
modified.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-17-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for Linux-PHY based CAN transceivers.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-16-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
an error
If request_irq() fails, forward the return value.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-15-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In at91_chip_start() first all IRQs are disabled, they do not have to
be disabled again at the end of the function before the requested IRQs
are enabled.
Remove the 2nd disable of all IRQs at the end of the function.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-14-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This message isn't really helpful for the general reader of the kernel
logs, so should not be printed with info level.
Link: https://lore.kernel.org/all/20231005-at91_can-rx_offload-v2-13-9987d53600e0@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
