| Age | Commit message (Collapse) | Author |
|---|
|
Implement mailbox communication between PF and VFs.
PF-VF mailbox is used for all control commands from VF to PF and
asynchronous notification messages from PF to VF.
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a bug in the ks8851 Ethernet driver that more data is written
to the hardware TX buffer than actually available. This is caused by
wrong accounting of the free TX buffer space.
The driver maintains a tx_space variable that represents the TX buffer
space that is deemed to be free. The ks8851_start_xmit_spi() function
adds an SKB to a queue if tx_space is large enough and reduces tx_space
by the amount of buffer space it will later need in the TX buffer and
then schedules a work item. If there is not enough space then the TX
queue is stopped.
The worker function ks8851_tx_work() dequeues all the SKBs and writes
the data into the hardware TX buffer. The last packet will trigger an
interrupt after it was send. Here it is assumed that all data fits into
the TX buffer.
In the interrupt routine (which runs asynchronously because it is a
threaded interrupt) tx_space is updated with the current value from the
hardware. Also the TX queue is woken up again.
Now it could happen that after data was sent to the hardware and before
handling the TX interrupt new data is queued in ks8851_start_xmit_spi()
when the TX buffer space had still some space left. When the interrupt
is actually handled tx_space is updated from the hardware but now we
already have new SKBs queued that have not been written to the hardware
TX buffer yet. Since tx_space has been overwritten by the value from the
hardware the space is not accounted for.
Now we have more data queued then buffer space available in the hardware
and ks8851_tx_work() will potentially overrun the hardware TX buffer. In
many cases it will still work because often the buffer is written out
fast enough so that no overrun occurs but for example if the peer
throttles us via flow control then an overrun may happen.
This can be fixed in different ways. The most simple way would be to set
tx_space to 0 before writing data to the hardware TX buffer preventing
the queuing of more SKBs until the TX interrupt has been handled. I have
chosen a slightly more efficient (and still rather simple) way and
track the amount of data that is already queued and not yet written to
the hardware. When new SKBs are to be queued the already queued amount
of data is honoured when checking free TX buffer space.
I tested this with a setup of two linked KS8851 running iperf3 between
the two in bidirectional mode. Before the fix I got a stall after some
minutes. With the fix I saw now issues anymore after hours.
Fixes: 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231214181112.76052-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
* tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: mt76: mt7996: Use DECLARE_FLEX_ARRAY() and fix -Warray-bounds warnings
wifi: ath11k: workaround too long expansion sparse warnings
Revert "wifi: ath12k: use ATH12K_PCI_IRQ_DP_OFFSET for DP IRQ"
wifi: rt2x00: remove useless code in rt2x00queue_create_tx_descriptor()
wifi: rtw89: only reset BB/RF for existing WiFi 6 chips while starting up
wifi: rtw89: add DBCC H2C to notify firmware the status
wifi: rtw89: mac: add suffix _ax to MAC functions
wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled
wifi: rtw89: 8922a: add power on/off functions
wifi: rtw89: add XTAL SI for WiFi 7 chips
wifi: rtw89: phy: print out RFK log with formatted string
wifi: rtw89: parse and print out RFK log from C2H events
wifi: rtw89: add C2H event handlers of RFK log and report
wifi: rtw89: load RFK log format string from firmware file
wifi: rtw89: fw: add version field to BB MCU firmware element
wifi: rtw89: fw: load TX power track tables from fw_element
wifi: mwifiex: configure BSSID consistently when starting AP
wifi: mwifiex: add extra delay for firmware ready
wifi: mac80211: sta_info.c: fix sentence grammar
wifi: mac80211: rx.c: fix sentence grammar
...
====================
Link: https://lore.kernel.org/r/20231218163900.C031DC433C9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most of idpf correctly uses FIELD_GET and FIELD_PREP, but a couple spots
were missed so fix those.
Automated conversion with coccinelle script and manually fixed up,
including audits for opportunities to convert to {get,encode,replace}
bits functions.
Add conversions to le16_get/encode/replace_bits where appropriate. And
in one place fix up a cast from a u16 to a u16.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
It was found while doing further testing of the previous commit
fbf32a9bab91 ("ice: field get conversion") that one of the FIELD_GET
conversions should really be a FIELD_PREP. The previous code was styled
as a match to the FIELD_GET conversion, which always worked because the
shift value was 0. The code makes way more sense as a FIELD_PREP and
was in fact the only FIELD_GET with two constant arguments in this
series.
Didn't squash this patch to make it easier to call out the
(non-impactful) bug.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor the ice driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor the iavf driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor the i40e driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
While making one of the conversions, an if() check was inverted to
return early and avoid un-necessary indentation of the remainder of the
function. In some other cases a stack variable was moved inside the
block where it was used while doing cleanups/review.
A couple places were changed to use le16_get_bits() instead of FIELD_GET
with a le16_to_cpu combination.
@get@
constant shift,mask;
metavariable type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor the igc driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor igc driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor iavf driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Clean up a couple spots in the code that had repetitive
y = cpu_to_*((blah << blah_blah) & blat)
y |= cpu_to_*((blahs << blahs_blahs) & blats)
to
x = FIELD_PREP(blat blah)
x |= FIELD_PREP(blats, blahs)
y = cpu_to_*(x);
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor i40e driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Refactor one function with multiple if's to return quickly to make lines
fit in 80 columns.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor several older Intel drivers to use FIELD_PREP(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For more than 15 years this code has passed in a request for a page and
masked off that page when read/writing. This code has been here forever,
but FIELD_PREP finds the bug when converted to use it. Change the code
to do exactly the same thing but allow the conversion to FIELD_PREP in a
later patch. To make it clear what we lost when making this change I
left a comment, but there is no point to change the code to generate a
correct sequence at this point.
This is not a Fixes tagged patch on purpose because it doesn't change
the binary output.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 6624e780a577fc596788 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.
Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:
ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time. While this was still in place, additional
support was added to specifically support SRIOV and LAG together. These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.
The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.
Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support. This will leave other systems unhindered with
functionality as it existed before any LAG code was added.
Fixes: bb52f42acef6 ("ice: Add driver support for firmware changes for LAG")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When creating new VSIs, they are assigned into an aggregator node in the
scheduler tree. Information about which aggregator node a VSI is assigned
into is maintained by the vsi->agg_node structure. In ice_vsi_decfg(), this
information is being destroyed, by overwriting the valid flag and the
agg_id field to zero.
For VF VSIs, this breaks the aggregator node configuration replay, which
depends on this information. This results in VFs being inserted into the
default aggregator node. The resulting configuration will have unexpected
Tx bandwidth sharing behavior.
This was broken by commit 6624e780a577 ("ice: split ice_vsi_setup into
smaller functions"), which added the block to reset the agg_node data.
The vsi->agg_node structure is not managed by the scheduler code, but is
instead a wrapper around an aggregator node ID that is tracked at the VSI
layer. Its been around for a long time, and its primary purpose was for
handling VFs. The SR-IOV VF reset flow does not make use of the standard VSI
rebuild/replay logic, and uses vsi->agg_node as part of its handling to
rebuild the aggregator node configuration.
The logic for aggregator nodes stretches back to early ice driver code from
commit b126bd6bcd67 ("ice: create scheduler aggregator node config and move
VSIs")
The logic in ice_vsi_decfg() which trashes the ice_agg_node data is clearly
wrong. It destroys information that is necessary for handling VF reset,. It
is also not the correct way to actually remove a VSI from an aggregator
node. For that, we need to implement logic in the scheduler code. Further,
non-VF VSIs properly replay their aggregator configuration using existing
scheduler replay logic.
To fix the VF replay logic, remove this broken aggregator node cleanup
logic. This is the simplest way to immediately fix this.
This ensures that VFs will have proper aggregate configuration after a
reset. This is especially important since VFs often perform resets as part
of their reconfiguration flows. Without fixing this, VFs will be placed in
the default aggregator node and Tx bandwidth will not be shared in the
expected and configured manner.
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
On older devices (before unified image!) we can end up calling
stop_device from an rfkill interrupt. However, in stop_device
we attempt to synchronize IRQs, which then of course deadlocks.
Avoid this by checking the context, if running from the IRQ
thread then don't synchronize. This wouldn't be correct on a
new device since RSS is supported, but older devices only have
a single interrupt/queue.
Fixes: 37fb29bd1f90 ("wifi: iwlwifi: pcie: synchronize IRQs before NAPI")
Reviewed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215111335.59aab00baed7.Iadfe154d6248e7f9dfd69522e5429dbbd72925d7@changeid
|
|
Some PHY in PHY package may require to read/write MMD regs to correctly
configure the PHY package.
Add support for these additional required function in both lock and no
lock variant.
It's assumed that the entire PHY package is either C22 or C45. We use
C22 or C45 way of writing/reading to mmd regs based on the passed phydev
whether it's C22 or C45.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restructure phy_write_mmd and phy_read_mmd to implement generic helper
for direct mdiobus access for mmd and use these helper for phydev user.
This is needed in preparation of PHY package API that requires generic
access to the mdiobus and are deatched from phydev struct but instead
access them based on PHY package base_addr and offsets.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current API for PHY package are limited to single address to configure
global settings for the PHY package.
It was found that some PHY package (for example the qca807x, a PHY
package that is shipped with a bundle of 5 PHY) requires multiple PHY
address to configure global settings. An example scenario is a PHY that
have a dedicated PHY for PSGMII/serdes calibrarion and have a specific
PHY in the package where the global PHY mode is set and affects every
other PHY in the package.
Change the API in the following way:
- Change phy_package_join() to take the base addr of the PHY package
instead of the global PHY addr.
- Make __/phy_package_write/read() require an additional arg that
select what global PHY address to use by passing the offset from the
base addr passed on phy_package_join().
Each user of this API is updated to follow this new implementation
following a pattern where an enum is defined to declare the offset of the
addr.
We also drop the check if shared is defined as any user of the
phy_package_read/write is expected to use phy_package_join first. Misuse
of this will correctly trigger a kernel panic for NULL pointer
exception.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some silicon variants the number of available CAM entries are
less. Reserving one entry for each NIX-LF for default DMAC based pkt
forwarding rules will reduce the number of available CAM entries
further. Hence add configurability via devlink to set maximum number of
NIX-LFs needed which inturn frees up some CAM entries.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.8.
We have new features only for ath12k but lots of small cleanup for
ath10k, ath11k and ath12k. And of course smaller fixes to several
drivers.
Major changes:
ath12k
* support one MSI vector
* WCN7850: support AP mode
|
|
Transform zero-length arrays `rate`, `adm_stat` and `msdu_cnt` into
proper flexible-array members in anonymous union in `struct
mt7996_mcu_all_sta_info_event` via the DECLARE_FLEX_ARRAY()
helper; and fix multiple -Warray-bounds warnings:
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:544:61: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:551:58: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:553:58: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:530:61: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:538:66: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:540:66: warning: array subscript <unknown> is outside array bounds of 'struct <anonymous>[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:520:57: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c:526:76: warning: array subscript <unknown> is outside array bounds of 'struct all_sta_trx_rate[0]' [-Warray-bounds=]
This results in no differences in binary output, helps with the ongoing
efforts to globally enable -Warray-bounds.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/ZXiU9ayVCslt3qiI@work
|
|
phylink_parse_mode() populates all possible supported link modes for a
given phy_interface_t, for the case where a phylib phy may be absent and
we can't retrieve the supported link modes from that.
Russell points out that since the introduction of the generic validation
helpers phylink_get_capabilities() and phylink_caps_to_linkmodes(), we
can rewrite this procedure to populate the pl->supported mask, so that
instead of spelling out the link modes, we derive an intermediary
mac_capabilities bit field, and we convert that to the equivalent link
modes.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling led_trigger_register() when attaching a PHY located on an SFP
module potentially (and practically) leads into a deadlock.
Fix this by not calling led_trigger_register() for PHYs localted on SFP
modules as such modules actually never got any LEDs.
======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4-next-20231208+ #0 Tainted: G O
------------------------------------------------------
kworker/u8:2/43 is trying to acquire lock:
ffffffc08108c4e8 (triggers_list_lock){++++}-{3:3}, at: led_trigger_register+0x4c/0x1a8
but task is already holding lock:
ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&sfp->sm_mutex){+.+.}-{3:3}:
__mutex_lock+0x88/0x7a0
mutex_lock_nested+0x20/0x28
cleanup_module+0x2ae0/0x3120 [sfp]
sfp_register_bus+0x5c/0x9c
sfp_register_socket+0x48/0xd4
cleanup_module+0x271c/0x3120 [sfp]
platform_probe+0x64/0xb8
really_probe+0x17c/0x3c0
__driver_probe_device+0x78/0x164
driver_probe_device+0x3c/0xd4
__driver_attach+0xec/0x1f0
bus_for_each_dev+0x60/0xa0
driver_attach+0x20/0x28
bus_add_driver+0x108/0x208
driver_register+0x5c/0x118
__platform_driver_register+0x24/0x2c
init_module+0x28/0xa7c [sfp]
do_one_initcall+0x70/0x2ec
do_init_module+0x54/0x1e4
load_module+0x1b78/0x1c8c
__do_sys_init_module+0x1bc/0x2cc
__arm64_sys_init_module+0x18/0x20
invoke_syscall.constprop.0+0x4c/0xdc
do_el0_svc+0x3c/0xbc
el0_svc+0x34/0x80
el0t_64_sync_handler+0xf8/0x124
el0t_64_sync+0x150/0x154
-> #2 (rtnl_mutex){+.+.}-{3:3}:
__mutex_lock+0x88/0x7a0
mutex_lock_nested+0x20/0x28
rtnl_lock+0x18/0x20
set_device_name+0x30/0x130
netdev_trig_activate+0x13c/0x1ac
led_trigger_set+0x118/0x234
led_trigger_write+0x104/0x17c
sysfs_kf_bin_write+0x64/0x80
kernfs_fop_write_iter+0x128/0x1b4
vfs_write+0x178/0x2a4
ksys_write+0x58/0xd4
__arm64_sys_write+0x18/0x20
invoke_syscall.constprop.0+0x4c/0xdc
do_el0_svc+0x3c/0xbc
el0_svc+0x34/0x80
el0t_64_sync_handler+0xf8/0x124
el0t_64_sync+0x150/0x154
-> #1 (&led_cdev->trigger_lock){++++}-{3:3}:
down_write+0x4c/0x13c
led_trigger_write+0xf8/0x17c
sysfs_kf_bin_write+0x64/0x80
kernfs_fop_write_iter+0x128/0x1b4
vfs_write+0x178/0x2a4
ksys_write+0x58/0xd4
__arm64_sys_write+0x18/0x20
invoke_syscall.constprop.0+0x4c/0xdc
do_el0_svc+0x3c/0xbc
el0_svc+0x34/0x80
el0t_64_sync_handler+0xf8/0x124
el0t_64_sync+0x150/0x154
-> #0 (triggers_list_lock){++++}-{3:3}:
__lock_acquire+0x12a0/0x2014
lock_acquire+0x100/0x2ac
down_write+0x4c/0x13c
led_trigger_register+0x4c/0x1a8
phy_led_triggers_register+0x9c/0x214
phy_attach_direct+0x154/0x36c
phylink_attach_phy+0x30/0x60
phylink_sfp_connect_phy+0x140/0x510
sfp_add_phy+0x34/0x50
init_module+0x15c/0xa7c [sfp]
cleanup_module+0x1d94/0x3120 [sfp]
cleanup_module+0x2bb4/0x3120 [sfp]
process_one_work+0x1f8/0x4ec
worker_thread+0x1e8/0x3d8
kthread+0x104/0x110
ret_from_fork+0x10/0x20
other info that might help us debug this:
Chain exists of:
triggers_list_lock --> rtnl_mutex --> &sfp->sm_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sfp->sm_mutex);
lock(rtnl_mutex);
lock(&sfp->sm_mutex);
lock(triggers_list_lock);
*** DEADLOCK ***
4 locks held by kworker/u8:2/43:
#0: ffffff80c000f938 ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec
#1: ffffffc08214bde8 ((work_completion)(&(&sfp->timeout)->work)){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec
#2: ffffffc0810902f8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x18/0x20
#3: ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp]
stack backtrace:
CPU: 0 PID: 43 Comm: kworker/u8:2 Tainted: G O 6.7.0-rc4-next-20231208+ #0
Hardware name: Bananapi BPI-R4 (DT)
Workqueue: events_power_efficient cleanup_module [sfp]
Call trace:
dump_backtrace+0xa8/0x10c
show_stack+0x14/0x1c
dump_stack_lvl+0x5c/0xa0
dump_stack+0x14/0x1c
print_circular_bug+0x328/0x430
check_noncircular+0x124/0x134
__lock_acquire+0x12a0/0x2014
lock_acquire+0x100/0x2ac
down_write+0x4c/0x13c
led_trigger_register+0x4c/0x1a8
phy_led_triggers_register+0x9c/0x214
phy_attach_direct+0x154/0x36c
phylink_attach_phy+0x30/0x60
phylink_sfp_connect_phy+0x140/0x510
sfp_add_phy+0x34/0x50
init_module+0x15c/0xa7c [sfp]
cleanup_module+0x1d94/0x3120 [sfp]
cleanup_module+0x2bb4/0x3120 [sfp]
process_one_work+0x1f8/0x4ec
worker_thread+0x1e8/0x3d8
kthread+0x104/0x110
ret_from_fork+0x10/0x20
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs")
Link: https://lore.kernel.org/r/102a9dce38bdf00215735d04cd4704458273ad9c.1702339354.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove double-mapping of DMA buffers as it can prevent page pool entries
from being freed. Mapping is managed by page pool infrastructure and
was previously managed by the driver in __bnxt_alloc_rx_page before
allowing the page pool infrastructure to manage it.
Fixes: 578fcfd26e2a ("bnxt_en: Let the page pool manage the DMA mapping")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://lore.kernel.org/r/20231214213138.98095-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In v6.7-rc1 sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:4702:15: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
drivers/net/wireless/ath/ath11k/mac.c:8393:23: error: too long token expansion
Workaround the warnings by refactoring the code to a new function, which also
reduces code duplication. And in the new function use max3() to make the code
more readable.
No functional changes, compile tested only.
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214161740.1582340-1-kvalo@kernel.org
|
|
This reverts commit 1f1f7d548a00ebe50808cb1f580df9693e194a7c. The commit
caused bootup failure on QCN9274 hw2.0 platform. Incorrect hardcode DP
irq offset overwrite the CE irq, which caused the driver to miss the
mandatory bootup message from the firmware through the CE interrupt. This
occurs because the CE count differs between platforms. The revert has no
impact since the original change was based on an incorrect assumption.
Log:
ath12k_pci 0000:06:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
ath12k_pci 0000:06:00.0: failed to receive control response completion, polling..
ath12k_pci 0000:06:00.0: Service connect timeout
ath12k_pci 0000:06:00.0: failed to connect to HTT: -110
ath12k_pci 0000:06:00.0: failed to start core: -110
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214053215.2087308-1-quic_periyasa@quicinc.com
|
|
In 'rt2x00queue_create_tx_descriptor()', there is no need to call
'ieee80211_get_rts_cts_rate()' while checking for RTS/CTS frame
since this function returns NULL or pointer to internal bitrate
table entry, and the return value is not actually used. Compile
tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213051449.126963-1-dmantipov@yandex.ru
|
|
The new WiFi 7 chips change the design, so no need to disable/enable
BB/RF when core_start(). Keep the same logic for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-7-pkshih@realtek.com
|
|
To support MLO of WiFi 7, we should configure hardware as DBCC mode, and
notify this status to firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-6-pkshih@realtek.com
|
|
Many existing MAC access functions are used by WiFi 6 chips only, so add
suffix _ax to be clearer. Some are common and can be used by WiFi 7, so
export this kind of functions. This patch doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-5-pkshih@realtek.com
|
|
Before accessing CMAC and DMAC registers, we should ensure they have been
powered on, so add flag to determine the state. For old chips, we read
registers and check corresponding bit, but it takes extra cost to read.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-4-pkshih@realtek.com
|
|
The power on/off functions are to turn on hardware function blocks and
to turn off them if we are going to stay in idle state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-3-pkshih@realtek.com
|
|
The XTAL SI is a serial interface to indirectly access registers of
analog hardware circuit. Since WiFi 7 chips use different registers, add
a ops to access them via common functions. This patch doesn't change logic
for existing chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231211083341.118047-2-pkshih@realtek.com
|
|
With formatted string loaded from firmware file, we can use the formatted
string ID and get corresponding string, and then use regular rtw89_debug()
to show the message if debug mask of RFK is enabled.
If the string ID doesn't present, fallback to print plain hexadecimal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-7-pkshih@realtek.com
|
|
RFK log events contains two types. One called RUN log is to reflect state
during RFK is running, and it replies on formatted string loaded from
firmware file, but print this type as plain hexadecimal only in this patch.
The other is REPORT log that reflects the final result of a RFK, and
each calibration has its own struct to carry many specific information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-6-pkshih@realtek.com
|
|
Trigger a RFK (RF calibration) in firmware by a H2C command, and in
progress it reports log and a result finally by C2H events. Firstly, add
prototype of the C2H event handlers to have a simple picture of framework.
The callers who trigger H2C will wait until a C2H event is received,
so we must process these C2H events in receiving process. Thus, mark this
kind of C2H events as atomic. Also, timestamp is also useful for
debugging, mark C2H events carrying RFK log as atomic as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-5-pkshih@realtek.com
|
|
To debug RFK (RF calibration) in firmware, it sends log via firmware C2H
events to driver with string format ID and four arguments. Load formatted
string from firmware file, and the string ID can get back its string. Then,
use regular print format to show the message.
This firmware element layout looks like
+============================================+
| elm ID | elm size | version | |
+----------+----------+----------+-----------+
| | nr |rsvd |rfk_id|rsvd|
+--------------------------------------------+
| offset[] (__le16 * nr) |
| ... |
+--------------------------------------------+
| formatted string with null termintor (*nr) |
| ... |
+============================================+
* a firmware file can contains more than one elements with this element ID
named RTW89_FW_ELEMENT_ID_RFKLOG_FMT (19), because many RFK needs its
own formatted strings, so add 'rfk_id' to know it belongs to which RFK.
* the 'formatted string' just follow 'offset[]' without padding to align
32bits.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-4-pkshih@realtek.com
|
|
8922AE has more than one hardware version, and they use different BB MCU
firmware, so occupy a byte from element priv[] to annotate version. Since
there are more than one firmware and only matched version is adopted,
return 1 to ignore not matched firmware.
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | element_priv[] |
+-------------------------------------------+
change to |
v
+===========================================+
| elm ID | elm size | version | |
+----------+----------+----------+----------+
| | cv | element_rsvd[] |
+-------------------------------------------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-3-pkshih@realtek.com
|
|
The TX power track tables are used to define compensation power reflected
to thermal value. Currently, we have 16 (2 * 4 * 2) tables made by
combinations of
{negative/positive thermal value, 2GHz/2GHz-CCK/5GHz/6GHz, path A/B}
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231213005054.10568-2-pkshih@realtek.com
|
|
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80bd ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
|
|
For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
|
|
When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.
cc: <stable@vger.kernel.org>
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
