| Age | Commit message (Collapse) | Author |
|---|
|
The filters set that will reproduce the problem:
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff action mirred egress \
redirect dev $PF0
$ tc filter add dev $VF0_PR ingress protocol arp prio 0 flower \
skip_sw dst_mac ff:ff:ff:ff:ff:ff src_mac 52:54:00:00:00:10 \
action mirred egress mirror dev $VF1_PR
Expected behaviour is to set all broadcast from VF0 to the LAN. If the
src_mac match the value from filters, send packet to LAN and to VF1.
In this case both LAN_EN and LB_EN flags in switch is set in case of
packet matching both filters. As dst VSI for the only LAN enable bit is
PF VSI, the packet is being seen on PF. To fix this change dst VSI to
the source VSI. It will block receiving any packet even when LB_EN is
set by switch, because local loopback is clear on VF VSI during normal
operation.
Side note: if the second filters action is redirect instead of mirror
LAN_EN is clear, because switch is AND-ing LAN_EN from each matched
filters and OR-ing LB_EN.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: 73b483b79029 ("ice: Manage act flags for switchdev offloads")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During peer create, dp setup for the peer is done where Rx TID is
updated for all the TIDs. Peer object for self peer will not go through
dp setup.
When core halts, dp cleanup is done for all the peers. While cleanup,
rx_tid::ab is accessed which causes below stack trace for self peer.
WARNING: CPU: 6 PID: 12297 at drivers/net/wireless/ath/ath12k/dp_rx.c:851
Call Trace:
__warn+0x7b/0x1a0
ath12k_dp_rx_frags_cleanup+0xd2/0xe0 [ath12k]
report_bug+0x10b/0x200
handle_bug+0x3f/0x70
exc_invalid_op+0x13/0x60
asm_exc_invalid_op+0x16/0x20
ath12k_dp_rx_frags_cleanup+0xd2/0xe0 [ath12k]
ath12k_dp_rx_frags_cleanup+0xca/0xe0 [ath12k]
ath12k_dp_rx_peer_tid_cleanup+0x39/0xa0 [ath12k]
ath12k_mac_peer_cleanup_all+0x61/0x100 [ath12k]
ath12k_core_halt+0x3b/0x100 [ath12k]
ath12k_core_reset+0x494/0x4c0 [ath12k]
sta object in peer will be updated when remote peer is created. Hence
use peer::sta to detect the self peer and skip the cleanup.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240905042851.2282306-1-quic_rgnanase@quicinc.com
|
|
Those two fields are used to store the per SPT page of tx/rx descriptors send to
the firmware for cookie conversion. Right now they are in struct ath12k_spt_info
which means they are duplicated PPT page times while we only need one instance
of them. This works for now as we always use the first spt_info as a global
storage for all PPT pages.
Let's move them into struct ath12k_dp where they belong, alongside of the
spt_info array they are tied to, to avoid waisting a good bit of memory.
Tested-on: QCN9274 hw2.0 PCI CI_WLAN.WBE.1.3-03283.1-QCAHKSWPL_SILICONZ-2
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Remi Pommarel <repk@triplefau.lt>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240830081942.3623380-1-nico.escande@gmail.com
|
|
On SC7280 platforms which are running with TrustZone, it is not
necessary to manually map the memory regions used by the wifi hardware.
However, ath11k will currently fail to load unless both memory regions
are specified.
This breaks wifi on the rb3gen2 which only specifies the firmware memory
region and does not use the CE region.
Adjust the order of operations in ath11k_ahb_fw_resources_init() to
check for the wifi-firmware subnode before attempting to parse the
memory regions.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240904095815.1572186-2-caleb.connolly@linaro.org
|
|
Fix the following W=1 kernel build warning:
drivers/net/wireless/ath/ath11k/wow.c: In function ‘ath11k_vif_wow_set_wakeups’:
drivers/net/wireless/ath/ath11k/wow.c:461:1: warning: the frame size of 1352 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Remove the nonessential variable 'struct cfg80211_pkt_pattern
old_pattern' by relocating bitmask to bytemask conversion into
ath11k_wow_convert_8023_to_80211().
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-04358-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240829075253.657667-1-quic_miaoqing@quicinc.com
|
|
WCN6750 firmware sends the log messages via WMI_DIAG_EVENTID only
when the host driver enables the same via QMI_WLANFW_WLAN_INI_REQ_V01
QMI message. This is further controlled via fw_wmi_diag_event.
Hence set this flag to true for the firmware to send the logs.
These logs are further collected in the user space through
the trace infrastructure.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00233-QCAMSLSWPLZ-1
Signed-off-by: Balaji Pothunoori <quic_bpothuno@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240828103043.2413-1-quic_bpothuno@quicinc.com
|
|
Currently struct ath11k_hal::srng_config pointer is not assigned
to NULL after freeing the memory in ath11k_hal_srng_deinit().
This could lead to double free issue in a scenario where
ath11k_hal_srng_deinit() is invoked back to back.
In the current code, although the chances are very low, the above
said scenario could happen when hardware recovery has failed and
then there is another FW assert where ath11k_hal_srng_deinit() is
invoked once again as part of recovery.
Fix this by assigning the struct ath11k_hal::srng_config pointer
to NULL after freeing the memory.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Balaji Pothunoori <quic_bpothuno@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240826053326.8878-1-quic_bpothuno@quicinc.com
|
|
Fix the following W=1 kernel build warning:
drivers/net/wireless/ath/ath10k/mac.c: In function ‘ath10k_hw_scan’:
drivers/net/wireless/ath/ath10k/mac.c:6468:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Compile tested only.
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240830015649.1083758-1-quic_miaoqing@quicinc.com
|
|
Fix the following W=1 kernel build warning:
drivers/net/wireless/ath/ath10k/mac.c: In function ‘ath10k_remain_on_channel’:
drivers/net/wireless/ath/ath10k/mac.c:7980:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Compile tested only.
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240830015349.1083226-1-quic_miaoqing@quicinc.com
|
|
In supported_vht_mcs_rate_nss2, the rate for MCS9 & VHT20 is defined as
{1560, 1733}, this does not align with firmware's definition and therefore
fails the verification in ath10k_mac_get_rate_flags_vht():
invalid vht params rate 1730 100kbps nss 2 mcs 9
and:
invalid vht params rate 1920 100kbps nss 2 mcs 9
Change it to {1730, 1920} to align with firmware to fix the issue.
Since ath10k_hw_params::supports_peer_stats_info is enabled only for
QCA6174, this change does not affect other chips.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00309-QCARMSWPZ-1
Fixes: 3344b99d69ab ("ath10k: add bitrate parse for peer stats info")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/lkml/fba24cd3-4a1e-4072-8585-8402272788ff@molgen.mpg.de/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 13 9360
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240711020344.98040-3-quic_bqiang@quicinc.com
|
|
In supported_vht_mcs_rate_nss1, the rate for MCS9 & VHT20 is defined as
{780, 867}, this does not align with firmware's definition and therefore
fails the verification in ath10k_mac_get_rate_flags_vht():
invalid vht params rate 960 100kbps nss 1 mcs 9
Change it to {865, 960} to align with firmware, so this issue could be
fixed.
Since ath10k_hw_params::supports_peer_stats_info is enabled only for
QCA6174, this change does not affect other chips.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00309-QCARMSWPZ-1
Fixes: 3344b99d69ab ("ath10k: add bitrate parse for peer stats info")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/lkml/fba24cd3-4a1e-4072-8585-8402272788ff@molgen.mpg.de/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240711020344.98040-2-quic_bqiang@quicinc.com
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are spelling mistakes in dev_err and dev_info messages. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time.
But the pm_runtime_disable() and pm_runtime_dont_use_autosuspend()
is missing in the error path for bam_dmux_probe(). So add it.
Found by code review. Compile-tested only.
Fixes: 21a0ffd9b38c ("net: wwan: Add Qualcomm BAM-DMUX WWAN network driver")
Suggested-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/20240911094234.1922418-1-ruanjinjie@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
It looks like that most people are still traveling: both the ML volume
and the processing capacity are low.
Previous releases - regressions:
- netfilter:
- nf_reject_ipv6: fix nf_reject_ip6_tcphdr_put()
- nf_tables: keep deleted flowtable hooks until after RCU
- tcp: check skb is non-NULL in tcp_rto_delta_us()
- phy: aquantia: fix -ETIMEDOUT PHY probe failure when firmware not
present
- eth: virtio_net: fix mismatched buf address when unmapping for
small packets
- eth: stmmac: fix zero-division error when disabling tc cbs
- eth: bonding: fix unnecessary warnings and logs from
bond_xdp_get_xmit_slave()
Previous releases - always broken:
- netfilter:
- fix clash resolution for bidirectional flows
- fix allocation with no memcg accounting
- eth: r8169: add tally counter fields added with RTL8125
- eth: ravb: fix rx and tx frame size limit"
* tag 'net-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (35 commits)
selftests: netfilter: Avoid hanging ipvs.sh
kselftest: add test for nfqueue induced conntrack race
netfilter: nfnetlink_queue: remove old clash resolution logic
netfilter: nf_tables: missing objects with no memcg accounting
netfilter: nf_tables: use rcu chain hook list iterator from netlink dump path
netfilter: ctnetlink: compile ctnetlink_label_size with CONFIG_NF_CONNTRACK_EVENTS
netfilter: nf_reject: Fix build warning when CONFIG_BRIDGE_NETFILTER=n
netfilter: nf_tables: Keep deleted flowtable hooks until after RCU
docs: tproxy: ignore non-transparent sockets in iptables
netfilter: ctnetlink: Guard possible unused functions
selftests: netfilter: nft_tproxy.sh: add tcp tests
selftests: netfilter: add reverse-clash resolution test case
netfilter: conntrack: add clash resolution for reverse collisions
netfilter: nf_nat: don't try nat source port reallocation for reverse dir clash
selftests/net: packetdrill: increase timing tolerance in debug mode
usbnet: fix cyclical race on disconnect with work queue
net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled
virtio_net: Fix mismatched buf address when unmapping for small packets
bonding: Fix unnecessary warnings and logs from bond_xdp_get_xmit_slave()
r8169: add missing MODULE_FIRMWARE entry for RTL8126A rev.b
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-balloon supports new stats
- vdpa supports setting mac address
- vdpa/mlx5 suspend/resume as well as MKEY ops are now faster
- virtio_fs supports new sysfs entries for queue info
- virtio/vsock performance has been improved
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits)
vsock/virtio: avoid queuing packets when intermediate queue is empty
vsock/virtio: refactor virtio_transport_send_pkt_work
fw_cfg: Constify struct kobj_type
vdpa/mlx5: Postpone MR deletion
vdpa/mlx5: Introduce init/destroy for MR resources
vdpa/mlx5: Rename mr_mtx -> lock
vdpa/mlx5: Extract mr members in own resource struct
vdpa/mlx5: Rename function
vdpa/mlx5: Delete direct MKEYs in parallel
vdpa/mlx5: Create direct MKEYs in parallel
MAINTAINERS: add virtio-vsock driver in the VIRTIO CORE section
virtio_fs: add sysfs entries for queue information
virtio_fs: introduce virtio_fs_put_locked helper
vdpa: Remove unused declarations
vdpa/mlx5: Parallelize VQ suspend/resume for CVQ MQ command
vdpa/mlx5: Small improvement for change_num_qps()
vdpa/mlx5: Keep notifiers during suspend but ignore
vdpa/mlx5: Parallelize device resume
vdpa/mlx5: Parallelize device suspend
vdpa/mlx5: Use async API for vq modify commands
...
|
|
The work can submit URBs and the URBs can schedule the work.
This cycle needs to be broken, when a device is to be stopped.
Use a flag to do so.
This is a design issue as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/20240919123525.688065-1-oneukum@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 5fabb01207a2 ("net: stmmac: Add initial XDP support") sets
PP_FLAG_DMA_SYNC_DEV flag for page_pool unconditionally,
page_pool_recycle_direct() will call page_pool_dma_sync_for_device()
on every page even the page is not going to be reused by XDP program.
When XDP is not enabled, the page which holds the received buffer
will be recycled once the buffer is copied into new SKB by
skb_copy_to_linear_data(), then the MAC core will never reuse this
page any longer. Always setting PP_FLAG_DMA_SYNC_DEV wastes CPU cycles
on unnecessary calling of page_pool_dma_sync_for_device().
After this patch, up to 9% noticeable performance improvement was observed
on certain platforms.
Fixes: 5fabb01207a2 ("net: stmmac: Add initial XDP support")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20240919121028.1348023-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the virtio-net driver will perform a pre-dma-mapping for
small or mergeable RX buffer. But for small packets, a mismatched address
without VIRTNET_RX_PAD and xdp_headroom is used for unmapping.
That will result in unsynchronized buffers when SWIOTLB is enabled, for
example, when running as a TDX guest.
This patch unifies the address passed to the virtio core as the address of
the virtnet header and fixes the mismatched buffer address.
Changes from v2: unify the buf that passed to the virtio core in small
and merge mode.
Changes from v1: Use ctx to get xdp_headroom.
Fixes: 295525e29a5b ("virtio_net: merge dma operations when filling mergeable buffers")
Signed-off-by: Wenbo Li <liwenbo.martin@bytedance.com>
Signed-off-by: Jiahui Cen <cenjiahui@bytedance.com>
Signed-off-by: Ying Fang <fangying.tommy@bytedance.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://patch.msgid.link/20240919081351.51772-1-liwenbo.martin@bytedance.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
rtw8703b_query_rx_desc(), rtw8723d_query_rx_desc(),
rtw8821c_query_rx_desc(), rtw8822b_query_rx_desc(), and
rtw8822c_query_rx_desc() are almost identical, so replace them all with
a single function, rtw_rx_query_rx_desc().
Also, access the RX descriptor using a struct with __le32 members and
le32_get_bits().
Tested with RTL8811CU, RTL8811AU, and RTL8812AU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Tested-by: Ping-Ke Shih <pkshih@realtek.com> # RTL8723DE and RTL8822CE
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/913f1747-38fc-4409-85a4-57bb9cee506b@gmail.com
|
|
_dpk_dgain_read()
The return value of _dpk_dgain_read() is not used afterward, so remove
it safely.
Addresses-Coverity-ID: 1504753 ("Unused value")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240919081216.28505-4-pkshih@realtek.com
|
|
For the case of DBCC enabled and fwrole version 0, the local variable
wl_rinfo.dbcc_2g_phy might not be set by following for-loop, leading
uninitialized variable before using.
Addresses-Coverity-ID: 1586724 ("Uninitialized scalar variable")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240919081216.28505-3-pkshih@realtek.com
|
|
The return value of ieee80211_probereq_get() might be NULL, so check it
before using to avoid NULL pointer access.
Addresses-Coverity-ID: 1529805 ("Dereference null return value")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240919081216.28505-2-pkshih@realtek.com
|
|
The km.state is not checked in driver's delayed work. When
xfrm_state_check_expire() is called, the state can be reset to
XFRM_STATE_EXPIRED, even if it is XFRM_STATE_DEAD already. This
happens when xfrm state is deleted, but not freed yet. As
__xfrm_state_delete() is called again in xfrm timer, the following
crash occurs.
To fix this issue, skip xfrm_state_check_expire() if km.state is not
XFRM_STATE_VALID.
Oops: general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP
CPU: 5 UID: 0 PID: 7448 Comm: kworker/u102:2 Not tainted 6.11.0-rc2+ #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5e_ipsec: eth%d mlx5e_ipsec_handle_sw_limits [mlx5_core]
RIP: 0010:__xfrm_state_delete+0x3d/0x1b0
Code: 0f 84 8b 01 00 00 48 89 fd c6 87 c8 00 00 00 05 48 8d bb 40 10 00 00 e8 11 04 1a 00 48 8b 95 b8 00 00 00 48 8b 85 c0 00 00 00 <48> 89 42 08 48 89 10 48 8b 55 10 48 b8 00 01 00 00 00 00 ad de 48
RSP: 0018:ffff88885f945ec8 EFLAGS: 00010246
RAX: dead000000000122 RBX: ffffffff82afa940 RCX: 0000000000000036
RDX: dead000000000100 RSI: 0000000000000000 RDI: ffffffff82afb980
RBP: ffff888109a20340 R08: ffff88885f945ea0 R09: 0000000000000000
R10: 0000000000000000 R11: ffff88885f945ff8 R12: 0000000000000246
R13: ffff888109a20340 R14: ffff88885f95f420 R15: ffff88885f95f400
FS: 0000000000000000(0000) GS:ffff88885f940000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2163102430 CR3: 00000001128d6001 CR4: 0000000000370eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? die_addr+0x33/0x90
? exc_general_protection+0x1a2/0x390
? asm_exc_general_protection+0x22/0x30
? __xfrm_state_delete+0x3d/0x1b0
? __xfrm_state_delete+0x2f/0x1b0
xfrm_timer_handler+0x174/0x350
? __xfrm_state_delete+0x1b0/0x1b0
__hrtimer_run_queues+0x121/0x270
hrtimer_run_softirq+0x88/0xd0
handle_softirqs+0xcc/0x270
do_softirq+0x3c/0x50
</IRQ>
<TASK>
__local_bh_enable_ip+0x47/0x50
mlx5e_ipsec_handle_sw_limits+0x7d/0x90 [mlx5_core]
process_one_work+0x137/0x2d0
worker_thread+0x28d/0x3a0
? rescuer_thread+0x480/0x480
kthread+0xb8/0xe0
? kthread_park+0x80/0x80
ret_from_fork+0x2d/0x50
? kthread_park+0x80/0x80
ret_from_fork_asm+0x11/0x20
</TASK>
Fixes: b2f7b01d36a9 ("net/mlx5e: Simulate missing IPsec TX limits hardware functionality")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When having larger RQ sizes and small MTUs sizes, the hd_per_wq variable
can overflow. Like in the following case:
$> ethtool --set-ring eth1 rx 8192
$> ip link set dev eth1 mtu 144
$> ethtool --features eth1 rx-gro-hw on
... yields in dmesg:
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:808:(pid 194797): CREATE_MKEY(0x200) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x3bf6f), err(-22)
because hd_per_wq is 64K which overflows to 0 and makes the command
fail.
This patch increases the variable size to 32 bit.
Fixes: 99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Fixed all the 'E2BIG' returns in error flow of functions to
the negative '-E2BIG' as we are using negative error codes
everywhere in HWS code.
This also fixes the following smatch warnings:
"warn: was negative '-E2BIG' intended?"
Fixes: 74a778b4a63f ("net/mlx5: HWS, added definers handling")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/f8c77688-7d83-4937-baba-ac844dfe2e0b@stanley.mountain/
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When SQ creation fails, call the appropriate mlx5_core destroy function.
This fixes the following smatch warnings:
divers/net/ethernet/mellanox/mlx5/core/steering/hws/mlx5hws_send.c:739
hws_send_ring_open_sq() warn: 'sq->dep_wqe' double freed
hws_send_ring_open_sq() warn: 'sq->wq_ctrl.buf.frags' double freed
hws_send_ring_open_sq() warn: 'sq->wr_priv' double freed
Fixes: 2ca62599aa0b ("net/mlx5: HWS, added send engine and context handling")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/e4ebc227-4b25-49bf-9e4c-14b7ea5c6a07@stanley.mountain/
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In mlx5e_tir_builder_alloc() kvzalloc() may return NULL
which is dereferenced on the next line in a reference
to the modify field.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a6696735d694 ("net/mlx5e: Convert TIR to a dedicated object")
Signed-off-by: Elena Salomatkina <esalomatkina@ispras.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Collecting crdump involves reading vsc registers from pci config space
of mlx device, which can take long time to complete. This might result
in starving other threads waiting to run on the cpu.
Numbers I got from testing ConnectX-5 Ex MCX516A-CDAT in the lab:
- mlx5_vsc_gw_read_block_fast() was called with length = 1310716.
- mlx5_vsc_gw_read_fast() reads 4 bytes at a time. It was not used to
read the entire 1310716 bytes. It was called 53813 times because
there are jumps in read_addr.
- On average mlx5_vsc_gw_read_fast() took 35284.4ns.
- In total mlx5_vsc_wait_on_flag() called vsc_read() 54707 times.
The average time for each call was 17548.3ns. In some instances
vsc_read() was called more than one time when the flag was not set.
As expected the thread released the cpu after 16 iterations in
mlx5_vsc_wait_on_flag().
- Total time to read crdump was 35284.4ns * 53813 ~= 1.898s.
It was seen in the field that crdump can take more than 5 seconds to
complete. During that time mlx5_vsc_wait_on_flag() did not release the
cpu because it did not complete 16 iterations. It is believed that pci
config reads were slow. Adding cond_resched() every 128 register read
improves the situation. In the common case the, crdump takes ~1.8989s,
the thread yields the cpu every ~4.51ms. If crdump takes ~5s, the thread
yields the cpu every ~18.0ms.
Fixes: 8b9d8baae1de ("net/mlx5: Add Crdump support")
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Remove the erroneous unmap in case no DMA mapping was established
The multi-packet WQE transmit code attempts to obtain a DMA mapping for
the skb. This could fail, e.g. under memory pressure, when the IOMMU
driver just can't allocate more memory for page tables. While the code
tries to handle this in the path below the err_unmap label it erroneously
unmaps one entry from the sq's FIFO list of active mappings. Since the
current map attempt failed this unmap is removing some random DMA mapping
that might still be required. If the PCI function now presents that IOVA,
the IOMMU may assumes a rogue DMA access and e.g. on s390 puts the PCI
function in error state.
The erroneous behavior was seen in a stress-test environment that created
memory pressure.
Fixes: 5af75c747e2a ("net/mlx5e: Enhanced TX MPWQE for SKBs")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Acked-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, commands that qualify as throttled can't be used via the
async API. That's due to the fact that the throttle semaphore can sleep
but the async API can't.
This patch allows throttling in the async API by using the tentative
variant of the semaphore and upon failure (semaphore at 0) returns EBUSY
to signal to the caller that they need to wait for the completion of
previously issued commands.
Furthermore, make sure that the semaphore is released in the callback.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Cc: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Message-Id: <20240816090159.1967650-2-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
|
|
Pull rdma updates from Jason Gunthorpe:
"Usual collection of small improvements and fixes, nothing especially
stands out to me here.
The new multipath PCI feature is a sign of things to come, I think we
will see more of this in the next 10 years. Broadcom and HNS continue
to update their drivers for their new HW generations.
Summary:
- Bug fixes and minor improvments in cxgb4, siw, mlx5, rxe, efa, rts,
hfi, erdma, hns, irdma
- Code cleanups/typos/etc. Tidy alloc_ordered_workqueue() calls
- Multipath PCI for mlx5
- Variable size work queue, SRQ changes, and relaxed ordering for new
bnxt HW
- New ODP fault resolution FW protocol in mlx5
- New 'rdma monitor' netlink mechanism"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
RDMA/bnxt_re: Remove the unused variable en_dev
RDMA/nldev: Add missing break in rdma_nl_notify_err_msg()
RDMA/irdma: fix error message in irdma_modify_qp_roce()
RDMA/cxgb4: Added NULL check for lookup_atid
RDMA/hns: Fix ah error counter in sw stat not increasing
RDMA/bnxt_re: Recover the device when FW error is detected
RDMA/bnxt_re: Group all operations under add_device and remove_device
RDMA/bnxt_re: Use the aux device for L2 ULP callbacks
RDMA/bnxt_re: Change aux driver data to en_info to hold more information
RDMA/nldev: Expose whether RDMA monitoring is supported
RDMA/nldev: Add support for RDMA monitoring
RDMA/mlx5: Use IB set_netdev and get_netdev functions
RDMA/device: Remove optimization in ib_device_get_netdev()
RDMA/mlx5: Initialize phys_port_cnt earlier in RDMA device creation
RDMA/mlx5: Obtain upper net device only when needed
RDMA/mlx5: Check RoCE LAG status before getting netdev
RDMA/mlx5: Consider the query_vuid cap for data_direct
net/mlx5: Handle memory scheme ODP capabilities
RDMA/mlx5: Add implicit MR handling to ODP memory scheme
RDMA/mlx5: Add handling for memory scheme page fault events
...
|
|
syzbot reported a WARNING in bond_xdp_get_xmit_slave. To reproduce
this[1], one bond device (bond1) has xdpdrv, which increases
bpf_master_redirect_enabled_key. Another bond device (bond0) which is
unsupported by XDP but its slave (veth3) has xdpgeneric that returns
XDP_TX. This triggers WARN_ON_ONCE() from the xdp_master_redirect().
To reduce unnecessary warnings and improve log management, we need to
delete the WARN_ON_ONCE() and add ratelimit to the netdev_err().
[1] Steps to reproduce:
# Needs tx_xdp with return XDP_TX;
ip l add veth0 type veth peer veth1
ip l add veth3 type veth peer veth4
ip l add bond0 type bond mode 6 # BOND_MODE_ALB, unsupported by XDP
ip l add bond1 type bond # BOND_MODE_ROUNDROBIN by default
ip l set veth0 master bond1
ip l set bond1 up
# Increases bpf_master_redirect_enabled_key
ip l set dev bond1 xdpdrv object tx_xdp.o section xdp_tx
ip l set veth3 master bond0
ip l set bond0 up
ip l set veth4 up
# Triggers WARN_ON_ONCE() from the xdp_master_redirect()
ip l set veth3 xdpgeneric object tx_xdp.o section xdp_tx
Reported-by: syzbot+c187823a52ed505b2257@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c187823a52ed505b2257
Fixes: 9e2ee5c7e7c3 ("net, bonding: Add XDP support to the bonding driver")
Signed-off-by: Jiwon Kim <jiwonaid0@gmail.com>
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20240918140602.18644-1-jiwonaid0@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a missing MODULE_FIRMWARE entry.
Fixes: 69cb89981c7a ("r8169: add support for RTL8126A rev.b")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/bb307611-d129-43f5-a7ff-bdb6b4044fce@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RX frame size limit should not be based on the current MTU setting.
Instead it should be based on the hardware capabilities.
While we're here, improve the description of the receive frame length
setting as suggested by Niklas.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The datasheets for all SoCs using the GbEth IP specify a maximum
transmission frame size of 1.5 kByte. I've confirmed through internal
discussions that support for 1522 byte frames has been validated, which
allows us to support the default MTU of 1500 bytes after reserving space
for the Ethernet header, frame checksums and an optional VLAN tag.
Fixes: 2e95e08ac009 ("ravb: Add rx_max_buf_size to struct ravb_hw_info")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commit b8c43360f6e4 ("net: stmmac: No need to calculate speed divider
when offload is disabled") allows the "port_transmit_rate_kbps" to be
set to a value of 0, which is then passed to the "div_s64" function when
tc-cbs is disabled. This leads to a zero-division error.
When tc-cbs is disabled, the idleslope, sendslope, and credit values the
credit values are not required to be configured. Therefore, adding a return
statement after setting the txQ mode to DCB when tc-cbs is disabled would
prevent a zero-division error.
Fixes: b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled")
Cc: <stable@vger.kernel.org>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
RTL8125 added fields to the tally counter, what may result in the chip
dma'ing these new fields to unallocated memory. Therefore make sure
that the allocated memory area is big enough to hold all of the
tally counter values, even if we use only parts of it.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/741d26a9-2b2b-485d-91d9-ecb302e345b5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
for_each_set_bit was used wrongly in aqr107_config_init() when iterating
over LEDs. Drop misleading 'index' variable and call
aqr_phy_led_active_low_set() for each set bit representing an LED which
is driven by VDD instead of GND pin.
Fixes: 61578f679378 ("net: phy: aquantia: add support for PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/9b1f0cd91f4cda54c8be56b4fe780480baf4aa0f.1726580902.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phy_modify_mmd was used wrongly in aqr_phy_led_active_low_set() resulting
in a no-op instead of setting the VEND1_GLOBAL_LED_DRIVE_VDD bit.
Correctly set VEND1_GLOBAL_LED_DRIVE_VDD bit.
Fixes: 61578f679378 ("net: phy: aquantia: add support for PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/ab963584b0a7e3b4dac39472a4b82ca264d79630.1726580902.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The drv_priv hooked to mac80211 become as below.
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_vif | <---> | rtw89_vif | -------> | rtw89_vif_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_vif_link |
+----------------+
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_sta | <---> | rtw89_sta | -------> | rtw89_sta_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_sta_link |
+----------------+
The relation bewteen mac80211 link_id and our link instance is like below.
|\
(link_id) | \
0 -------- | |
1 -------- | | ------ instance-0 (link_id: X) -> work on HW band 0
2 -------- | |
... | | ------ instance-1 (link_id: Y) -> work on HW band 1
14 -------- | |
| /
|/
N.B. For cases of non-MLD connection, we set our link instance-0
active with link_id 0. So, our code flow can be compatible between
non-MLD connection and MLD connection.
Based on above, we tweak entire driver architecture first. But, we don't
dynamically enable multiple links here. That will be handled separately.
Most of the things changed here are changing flows to iterate all active
links and read bss_conf/link_sta data according to target link. And, for
cases of scan, ROC, WOW, we use instance-0 to deal with the request.
There are some things listed below, which work for now but need to extend
before multiple active links.
1. tx path
select suitable link instance among multiple active links
2. rx path
determine rx link by PPDU instead of always link instance-0
3. CAM
apply MLD pairwise key to any active links dynamically
Besides, PS code cannot easily work along with tweaking architecture. With
supporting MLO flag (currently false), we disable PS first and will fix it
by another commit in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-8-pkshih@realtek.com
|
|
Refactor STA related functions, e.g. add/assoc/disassoc/disconnect/remove
to separate most link stuffs into sub-functions for MLO reuse.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-7-pkshih@realtek.com
|
|
Refactor VIF related functions, e.g. add/remove/assoc/mapping
to separate most link stuffs into sub-functions for MLO reuse.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-6-pkshih@realtek.com
|
|
Tweak code to not always access sta->deflink directly. Instead,
according to link_id, read target link_sta from sta->link[].
For now, rtwsta_link->link_id keeps 0. When driver starts to
support MLO, the link_id will be assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-5-pkshih@realtek.com
|
|
Tweak code to not always access vif->bss_conf directly. Instead,
according to link_id, read target bss_conf from vif->link_conf[].
For now, rtwvif_link->link_id keeps 0. When driver starts to
support MLO, the link_id will be assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-4-pkshih@realtek.com
|
|
This is an intermediate version that is separated from subsequent major
MLO changes, so some functions' namings are not really determined here.
e.g. struct rtw89_sta_link *sta_to_rtwsta_safe(struct ieee80211_sta *sta)
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-3-pkshih@realtek.com
|
