| Age | Commit message (Collapse) | Author |
|---|
|
SCS is obsoleted and no longer used, so remove it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
To make sure we have the proper antenna config in 6g cap,
move IEEE80211_VHT_CAP_[T/R]X_ANTENNA_PATTERN to stream init.
Fixes: edf9dab8ba27 ("mt76: add 6GHz support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
add AP mode support to mt7921 that can work for mt7921[e,s,u]
with the common code.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use 0xff (GENMASK(7,0)) in mt7915_init_bitrate_mask routine in order to
initialize bitrate_mask structure in order to avoid truncating value in
memset().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Report rx mode in mt7915_mac_fill_rx_rate routine in order to properly
add he radiotap if mode is at least HE_SU.
Fixes: 1c9db0aa23fd1 ("mt76: mt7915: update rx rate reporting for mt7916")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix typo in mt7915_muru_debug_set routine and pass muru_debug value to
mt7915_mcu_muru_debug_set() instead of data pointer.
Fixes: 1966a5078f2d ("mt76: mt7915: add mu-mimo and ofdma debugfs knobs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
routine if the chip does not support dbdc and the hw reports band_idx
set to 1.
Fixes: 78fc30a21cf11 ("mt76: mt7915: move testmode data from dev to phy")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7986_wmac_gpio_setup
Add default case for type switch in mt7986_wmac_gpio_setup routine in
order to avoid a possible uninitialized pointer dereference.
Fixes: 99ad32a4ca3a2 ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In case of error, some resources must be freed, as already done above and
below the devm_kmemdup() and __mt7921e_mcu_drv_pmctrl() calls added in the
commit in Fixes:.
Fixes: 602cc0c9618a ("mt76: mt7921e: fix possible probe failure after reboot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the following smatch static checker warning:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1872 mt7915_mcu_beacon_mbss()
error: undefined (user controlled) shift '(((1))) << (data[2])'
Rely on mac80211 definitions for ieee80211_bssid_index subelement.
Fixes: 6b7f9aff7c67 ("mt76: mt7915: introduce 802.11ax multi-bss support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Soft reboot might not clear certain condition, so always call
mt7915_wfsys_reset() during init.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Honor runtime-pm user configuration in mt7921_sniffer_interface_iter
routine if we do not have a monitor interface.
Fixes: 1f12fa34e5dc5 ("mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR is set")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt7921 is currently using rxfilter defined in mt76_dev for rx filter
configuration. Fix mt7921_configure_filter implementation.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Introduce suspend/resume callbacks for mt7921u driver.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
MT7915_MAX_INTERFACES is per-band declaration in MT7915/MT7986/MT7916.
Enlarge vif_mask to 64 bits wide, including the bit operation.
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fixes an issue caught by KASAN about use-after-free in mt76_txq_schedule
by protecting mtxq->wcid with rcu_lock between mt76_txq_schedule and
sta_info_[alloc, free].
[18853.876689] ==================================================================
[18853.876751] BUG: KASAN: use-after-free in mt76_txq_schedule+0x204/0xaf8 [mt76]
[18853.876773] Read of size 8 at addr ffffffaf989a2138 by task mt76-tx phy0/883
[18853.876786]
[18853.876810] CPU: 5 PID: 883 Comm: mt76-tx phy0 Not tainted 5.10.100-fix-510-56778d365941-kasan #5 0b01fbbcf41a530f52043508fec2e31a4215
[18853.876840] Call trace:
[18853.876861] dump_backtrace+0x0/0x3ec
[18853.876878] show_stack+0x20/0x2c
[18853.876899] dump_stack+0x11c/0x1ac
[18853.876918] print_address_description+0x74/0x514
[18853.876934] kasan_report+0x134/0x174
[18853.876948] __asan_report_load8_noabort+0x44/0x50
[18853.876976] mt76_txq_schedule+0x204/0xaf8 [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877002] mt76_txq_schedule_all+0x2c/0x48 [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877030] mt7921_tx_worker+0xa0/0x1cc [mt7921_common f0875ebac9d7b4754e1010549e7db50fbd90a047]
[18853.877054] __mt76_worker_fn+0x190/0x22c [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877071] kthread+0x2f8/0x3b8
[18853.877087] ret_from_fork+0x10/0x30
[18853.877098]
[18853.877112] Allocated by task 941:
[18853.877131] kasan_save_stack+0x38/0x68
[18853.877147] __kasan_kmalloc+0xd4/0xfc
[18853.877163] kasan_kmalloc+0x10/0x1c
[18853.877177] __kmalloc+0x264/0x3c4
[18853.877294] sta_info_alloc+0x460/0xf88 [mac80211]
[18853.877410] ieee80211_prep_connection+0x204/0x1ee0 [mac80211]
[18853.877523] ieee80211_mgd_auth+0x6c4/0xa4c [mac80211]
[18853.877635] ieee80211_auth+0x20/0x2c [mac80211]
[18853.877733] rdev_auth+0x7c/0x438 [cfg80211]
[18853.877826] cfg80211_mlme_auth+0x26c/0x390 [cfg80211]
[18853.877919] nl80211_authenticate+0x6d4/0x904 [cfg80211]
[18853.877938] genl_rcv_msg+0x748/0x93c
[18853.877954] netlink_rcv_skb+0x160/0x2a8
[18853.877969] genl_rcv+0x3c/0x54
[18853.877985] netlink_unicast_kernel+0x104/0x1ec
[18853.877999] netlink_unicast+0x178/0x268
[18853.878015] netlink_sendmsg+0x3cc/0x5f0
[18853.878030] sock_sendmsg+0xb4/0xd8
[18853.878043] ____sys_sendmsg+0x2f8/0x53c
[18853.878058] ___sys_sendmsg+0xe8/0x150
[18853.878071] __sys_sendmsg+0xc4/0x1f4
[18853.878087] __arm64_compat_sys_sendmsg+0x88/0x9c
[18853.878101] el0_svc_common+0x1b4/0x390
[18853.878115] do_el0_svc_compat+0x8c/0xdc
[18853.878131] el0_svc_compat+0x10/0x1c
[18853.878146] el0_sync_compat_handler+0xa8/0xcc
[18853.878161] el0_sync_compat+0x188/0x1c0
[18853.878171]
[18853.878183] Freed by task 10927:
[18853.878200] kasan_save_stack+0x38/0x68
[18853.878215] kasan_set_track+0x28/0x3c
[18853.878228] kasan_set_free_info+0x24/0x48
[18853.878244] __kasan_slab_free+0x11c/0x154
[18853.878259] kasan_slab_free+0x14/0x24
[18853.878273] slab_free_freelist_hook+0xac/0x1b0
[18853.878287] kfree+0x104/0x390
[18853.878402] sta_info_free+0x198/0x210 [mac80211]
[18853.878515] __sta_info_destroy_part2+0x230/0x2d4 [mac80211]
[18853.878628] __sta_info_flush+0x300/0x37c [mac80211]
[18853.878740] ieee80211_set_disassoc+0x2cc/0xa7c [mac80211]
[18853.878851] ieee80211_mgd_deauth+0x4a4/0x10a0 [mac80211]
[18853.878962] ieee80211_deauth+0x20/0x2c [mac80211]
[18853.879057] rdev_deauth+0x7c/0x438 [cfg80211]
[18853.879150] cfg80211_mlme_deauth+0x274/0x414 [cfg80211]
[18853.879243] cfg80211_mlme_down+0xe4/0x118 [cfg80211]
[18853.879335] cfg80211_disconnect+0x218/0x2d8 [cfg80211]
[18853.879427] __cfg80211_leave+0x17c/0x240 [cfg80211]
[18853.879519] cfg80211_leave+0x3c/0x58 [cfg80211]
[18853.879611] wiphy_suspend+0xdc/0x200 [cfg80211]
[18853.879628] dpm_run_callback+0x58/0x408
[18853.879642] __device_suspend+0x4cc/0x864
[18853.879658] async_suspend+0x34/0xf4
[18853.879673] async_run_entry_fn+0xe0/0x37c
[18853.879689] process_one_work+0x508/0xb98
[18853.879702] worker_thread+0x7f4/0xcd4
[18853.879717] kthread+0x2f8/0x3b8
[18853.879731] ret_from_fork+0x10/0x30
[18853.879741]
[18853.879757] The buggy address belongs to the object at ffffffaf989a2000
[18853.879757] which belongs to the cache kmalloc-8k of size 8192
[18853.879774] The buggy address is located 312 bytes inside of
[18853.879774] 8192-byte region [ffffffaf989a2000, ffffffaf989a4000)
[18853.879787] The buggy address belongs to the page:
[18853.879807] page:000000004bda2a59 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1d89a0
[18853.879823] head:000000004bda2a59 order:3 compound_mapcount:0 compound_pincount:0
[18853.879839] flags: 0x8000000000010200(slab|head)
[18853.879857] raw: 8000000000010200 ffffffffbc89e208 ffffffffb7fb5208 ffffffaec000cc80
[18853.879873] raw: 0000000000000000 0000000000010001 00000001ffffffff 0000000000000000
[18853.879885] page dumped because: kasan: bad access detected
[18853.879896]
[18853.879907] Memory state around the buggy address:
[18853.879922] ffffffaf989a2000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[18853.879935] ffffffaf989a2080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[18853.879948] >ffffffaf989a2100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[18853.879961] ^
[18853.879973] ffffffaf989a2180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[18853.879986] ffffffaf989a2200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[18853.879998] ==================================================================
Cc: stable@vger.kernel.org
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The hardware receives them properly, they should not be dropped
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The hardware receives them properly, they should not be dropped
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
dma unmap is already needed for cleanup anyway, so we don't need the extra
tracking and can save a bit of memory here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
- call txq dequeue without holding txq lock (locking handled by mac80211)
- disable bh around tx queue schedule
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Clean up and fix error paths in mt7915_register_device
Initialize second DBDC tx queue in mt7915_dma_init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This code was accidentally dropped while adding 6 GHz support
Fixes: b4d093e321bd ("mt76: mt7915: add 6 GHz support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This memory allocation failure can be triggered by fault injection or
high pressure testing, resulting a WARN.
Fix this by replacing WARN with pr_warn.
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220511014453.1621366-1-dzm91@hust.edu.cn
|
|
They were removed in the first series since they were not used for EF10.
Put that code back for Siena, with the prototypes in siena_sriov.h
since that file is a more applicable place for it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the clock name and work queue names to differentiate them from
the names used in sfc.ko.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a Siena Kconfig option and use it in stead of the sfc one.
Rename the internal variable for the 'mcdi_logging_default' module
parameter to avoid a naming conflict with the one in sfc.ko.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a Siena Kconfig option and use it in stead of the sfc one.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The error handling for the current tagging protocol change procedure is
a bit brittle (we dismantle the previous tagging protocol entirely
before setting up the new one). By identifying which parts of a tagging
protocol are unique to itself and which parts are shared with the other,
we can implement a protocol change procedure where error handling is a
bit more robust, because we start setting up the new protocol first, and
tear down the old one only after the setup of the specific and shared
parts succeeded.
The protocol change is a bit too open-coded too, in the area of
migrating host flood settings and MDBs. By identifying what differs
between tagging protocols (the forwarding masks for host flooding) we
can implement a more straightforward migration procedure which is
handled in the shared portion of the protocol change, rather than
individually by each protocol.
Therefore, a more structured approach calls for the introduction of a
structure of function pointers per tagging protocol. This covers setup,
teardown and the host forwarding mask. In the future it will also cover
how to prepare for a new DSA master.
The initial tagging protocol setup (at driver probe time) and the final
teardown (at driver removal time) are also adapted to call into the
structured methods of the specific protocol in current use. This is
especially relevant for teardown, where we previously called
felix_del_tag_protocol() only for the first CPU port. But by not
specifying which CPU port this is for, we gain more flexibility to
support multiple CPU ports in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ocelot switches support a single active CPU port at a time (at least as
a trapping destination, i.e. for control traffic). This is true
regardless of whether we are using the native copy-to-CPU-port-module
functionality, or a redirect action towards the software-defined
tag_8021q CPU port.
Currently we assume that the trapping destination in tag_8021q mode is
the first CPU port, yet in the future we may want to migrate the user
ports to the second CPU port.
For that to work, we need to make sure that the tag_8021q trapping
destination is a CPU port that is active, i.e. is used by at least some
user port on which the trap was added. Otherwise, we may end up
redirecting the traffic to a CPU port which isn't even up.
Note that due to the current design where we simply choose the CPU port
of the first port from the trap's ingress port mask, it may be that a
CPU port absorbes control traffic from user ports which aren't affine to
it as per user space's request. This isn't ideal, but is the lesser of
two evils. Following the user-configured affinity for traps would mean
that we can no longer reuse a single TCAM entry for multiple traps,
which is what we actually do for e.g. PTP. Either we duplicate and
deduplicate TCAM entries on the fly when user-to-CPU-port mappings
change (which is unnecessarily complicated), or we redirect trapped
traffic to all tag_8021q CPU ports if multiple such ports are in use.
The latter would have actually been nice, if it actually worked, but it
doesn't, since a OCELOT_MASK_MODE_REDIRECT action towards multiple ports
would not take PGID_SRC into consideration, and it would just duplicate
the packet towards each (CPU) port, leading to duplicates in software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA has not supported (and probably will not support in the future
either) independent tagging protocols per CPU port.
Different switch drivers have different requirements, some may need to
replicate some settings for each CPU port, some may need to apply some
settings on a single CPU port, while some may have to configure some
global settings and then some per-CPU-port settings.
In any case, the current model where DSA calls ->change_tag_protocol for
each CPU port turns out to be impractical for drivers where there are
global things to be done. For example, felix calls dsa_tag_8021q_register(),
which makes no sense per CPU port, so it suppresses the second call.
Let drivers deal with replication towards all CPU ports, and remove the
CPU port argument from the function prototype.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the time - commit 7569459a52c9 ("net: dsa: manage flooding on the CPU
ports") - not introducing a dedicated switch callback for host flooding
made sense, because for the only user, the felix driver, there was
nothing different to do for the CPU port than set the flood flags on the
CPU port just like on any other bridge port.
There are 2 reasons why this approach is not good enough, however.
(1) Other drivers, like sja1105, support configuring flooding as a
function of {ingress port, egress port}, whereas the DSA
->port_bridge_flags() function only operates on an egress port.
So with that driver we'd have useless host flooding from user ports
which don't need it.
(2) Even with the felix driver, support for multiple CPU ports makes it
difficult to piggyback on ->port_bridge_flags(). The way in which
the felix driver is going to support host-filtered addresses with
multiple CPU ports is that it will direct these addresses towards
both CPU ports (in a sort of multicast fashion), then restrict the
forwarding to only one of the two using the forwarding masks.
Consequently, flooding will also be enabled towards both CPU ports.
However, ->port_bridge_flags() gets passed the index of a single CPU
port, and that leaves the flood settings out of sync between the 2
CPU ports.
This is to say, it's better to have a specific driver method for host
flooding, which takes the user port as argument. This solves problem (1)
by allowing the driver to do different things for different user ports,
and problem (2) by abstracting the operation and letting the driver do
whatever, rather than explicitly making the DSA core point to the CPU
port it thinks needs to be touched.
This new method also creates a problem, which is that cross-chip setups
are not handled. However I don't have hardware right now where I can
test what is the proper thing to do, and there isn't hardware compatible
with multi-switch trees that supports host flooding. So it remains a
problem to be tackled in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For symmetry with host FDBs and MDBs where the indirection is now
handled outside the ocelot switch lib, do the same for bridge port
flags (unicast/multicast/broadcast flooding).
The only caller of the ocelot switch lib which uses the NPI port is the
Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For symmetry with host FDBs where the indirection is now handled outside
the ocelot switch lib, do the same for host MDB entries. The only caller
of the ocelot switch lib which uses the NPI port is the Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I remembered why we had the host FDB migration procedure in place.
It is true that host FDB entry migration can be done by changing the
value of PGID_CPU, but the problem is that only host FDB entries learned
while operating in NPI mode go to PGID_CPU. When the CPU port operates
in tag_8021q mode, the FDB entries are learned towards the unicast PGID
equal to the physical port number of this CPU port, bypassing the
PGID_CPU indirection.
So host FDB entries learned in tag_8021q mode are not migrated any
longer towards the NPI port.
Fix this by extracting the NPI port -> PGID_CPU redirection from the
ocelot switch lib, moving it to the Felix DSA driver, and applying it
for any CPU port regardless of its kind (NPI or tag_8021q).
Fixes: a51c1c3f3218 ("net: dsa: felix: stop migrating FDBs back and forth on tag proto change")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The smatch found the following warning:
drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c:736 lan966x_fdma_reload()
warn: 'rx_dcbs' was already freed.
This issue can happen when changing the MTU on one of the ports and once
the RX buffers are allocated and then the TX buffer allocation fails.
In that case the RX buffers should not be restore. This fix this issue
such that the RX buffers will not be restored if the TX buffers failed
to be allocated.
Fixes: 2ea1cbac267e2a ("net: lan966x: Update FDMA to change MTU.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220511204059.2689199-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver currently has three interrupt counters,
which are incremented every time each interrupt handler
executes. These driver-managed counters are not
necessary as the kernel already has logic that manages
interrupt counts and exposes them via /proc/interrupts.
This patch removes the driver-managed counters.
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Link: https://lore.kernel.org/r/20220511135251.2989-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the NIC ->probe() callback, ->mtd_probe() callback is called.
If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too.
In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and
initializes mtd partiion.
But mtd partition for sfc is shared data.
So that allocated mtd partition data from last called
efx_ef10_mtd_probe() will not be used.
Therefore it must be freed.
But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe().
kmemleak reports:
unreferenced object 0xffff88811ddb0000 (size 63168):
comm "systemd-udevd", pid 265, jiffies 4294681048 (age 348.586s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffffa3767749>] kmalloc_order_trace+0x19/0x120
[<ffffffffa3873f0e>] __kmalloc+0x20e/0x250
[<ffffffffc041389f>] efx_ef10_mtd_probe+0x11f/0x270 [sfc]
[<ffffffffc0484c8a>] efx_pci_probe.cold.17+0x3df/0x53d [sfc]
[<ffffffffa414192c>] local_pci_probe+0xdc/0x170
[<ffffffffa4145df5>] pci_device_probe+0x235/0x680
[<ffffffffa443dd52>] really_probe+0x1c2/0x8f0
[<ffffffffa443e72b>] __driver_probe_device+0x2ab/0x460
[<ffffffffa443e92a>] driver_probe_device+0x4a/0x120
[<ffffffffa443f2ae>] __driver_attach+0x16e/0x320
[<ffffffffa4437a90>] bus_for_each_dev+0x110/0x190
[<ffffffffa443b75e>] bus_add_driver+0x39e/0x560
[<ffffffffa4440b1e>] driver_register+0x18e/0x310
[<ffffffffc02e2055>] 0xffffffffc02e2055
[<ffffffffa3001af3>] do_one_initcall+0xc3/0x450
[<ffffffffa33ca574>] do_init_module+0x1b4/0x700
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Fixes: 8127d661e77f ("sfc: Add support for Solarflare SFC9100 family")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220512054709.12513-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220512021731.2494261-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPv6 addresses which are used for tunnels are stored in a hash table
with reference counting. When a new GRE tunnel is configured, the driver
is notified and configures it in hardware.
Currently, any change in the tunnel is not applied in the driver. It
means that if the remote address is changed, the driver is not aware of
this change and the first address will be used.
This behavior results in a warning [1] in scenarios such as the
following:
# ip link add name gre1 type ip6gre local 2000::3 remote 2000::fffe tos inherit ttl inherit
# ip link set name gre1 type ip6gre local 2000::3 remote 2000::ffff ttl inherit
# ip link delete gre1
The change of the address is not applied in the driver. Currently, the
driver uses the remote address which is stored in the 'parms' of the
overlay device. When the tunnel is removed, the new IPv6 address is
used, the driver tries to release it, but as it is not aware of the
change, this address is not configured and it warns about releasing non
existing IPv6 address.
Fix it by using the IPv6 address which is cached in the IPIP entry, this
address is the last one that the driver used, so even in cases such the
above, the first address will be released, without any warning.
[1]:
WARNING: CPU: 1 PID: 2197 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2920 mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum]
...
CPU: 1 PID: 2197 Comm: ip Not tainted 5.17.0-rc8-custom-95062-gc1e5ded51a9a #84
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum]
...
Call Trace:
<TASK>
mlxsw_sp2_ipip_rem_addr_unset_gre6+0xf1/0x120 [mlxsw_spectrum]
mlxsw_sp_netdevice_ipip_ol_event+0xdb/0x640 [mlxsw_spectrum]
mlxsw_sp_netdevice_event+0xc4/0x850 [mlxsw_spectrum]
raw_notifier_call_chain+0x3c/0x50
call_netdevice_notifiers_info+0x2f/0x80
unregister_netdevice_many+0x311/0x6d0
rtnl_dellink+0x136/0x360
rtnetlink_rcv_msg+0x12f/0x380
netlink_rcv_skb+0x49/0xf0
netlink_unicast+0x233/0x340
netlink_sendmsg+0x202/0x440
____sys_sendmsg+0x1f3/0x220
___sys_sendmsg+0x70/0xb0
__sys_sendmsg+0x54/0xa0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: e846efe2737b ("mlxsw: spectrum: Add hash table for IPv6 address mapping")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220511115747.238602-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add VF rate limit feature
This patch enhances the NFP driver to supports assignment of
both max_tx_rate and min_tx_rate to VFs
The template of configurations below is all supported.
e.g.
# ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM max_tx_rate $RATE_VALUE \
min_tx_rate $RATE_VALUE
# ip link set $DEV vf $VF_NUM min_tx_rate $RATE_VALUE \
max_tx_rate $RATE_VALUE
The max RATE_VALUE is limited to 0xFFFF which is about
63Gbps (using 1024 for 1G)
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220511104448.150800-1-colin.i.king@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle)
doesn't register with phylink, but calls netif_carrier_on() from
enetc_start().
This makes sense for a VF, but for a PF, this is braindead, because we
never call enetc_mac_enable() so the MAC is left inoperational.
Furthermore, commit 71b77a7a27a3 ("enetc: Migrate to PHYLINK and
PCS_LYNX") put the nail in the coffin because it removed the initial
netif_carrier_off() call done right after register_netdev().
Without that call, netif_carrier_on() does not call
linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN.
Just deny the broken configuration by requiring that a phy-mode is
present, and always register a PF with phylink.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As we continue to narrow the scope of what the FORTIFY memcpy() will
accept and build alternative APIs that give the compiler appropriate
visibility into more complex memcpy scenarios, there is a need for
"unfortified" memcpy use in rare cases where combinations of compiler
behaviors, source code layout, etc, result in cases where the stricter
memcpy checks need to be bypassed until appropriate solutions can be
developed (i.e. fix compiler bugs, code refactoring, new API, etc). The
intention is for this to be used only if there's no other reasonable
solution, for its use to include a justification that can be used
to assess future solutions, and for it to be temporary.
Example usage included, based on analysis and discussion from:
https://lore.kernel.org/netdev/CANn89iLS_2cshtuXPyNUGDPaic=sJiYfvTb_wNLgWrZRyBxZ_g@mail.gmail.com
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220511025301.3636666-1-keescook@chromium.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The interrupt controller supplying the Wake-on-LAN interrupt line maybe
modular on some platforms (irq-bcm7038-l1.c) and might be probed at a
later time than the GENET driver. We need to specifically check for
-EPROBE_DEFER and propagate that error to ensure that we eventually
fetch the interrupt descriptor.
Fixes: 9deb48b53e7f ("bcmgenet: add WOL IRQ check")
Fixes: 5b1f0e62941b ("net: bcmgenet: Avoid touching non-existent interrupt")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
'foe_table' is a pointer, the real size of struct mtk_foe_entry
should be pass to memset().
Fixes: ba37b7caf1ed ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220511030829.3308094-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
