| Age | Commit message (Collapse) | Author |
|---|
|
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For some time now, if you load the bonding driver and configure bond
parameters via sysfs using minimal config options, such as specifying
nothing but the mode, relying on defaults for everything else, modes
that cannot use arp monitoring (802.3ad, balance-tlb, balance-alb) all
wind up with both arp_interval=0 (as it should be) and miimon=0, which
means the miimon monitor thread never actually runs. This is particularly
problematic for 802.3ad.
For example, from an LNST recipe I've set up:
$ modprobe bonding max_bonds=0"
$ echo "+t_bond0" > /sys/class/net/bonding_masters"
$ ip link set t_bond0 down"
$ echo "802.3ad" > /sys/class/net/t_bond0/bonding/mode"
$ ip link set ens1f1 down"
$ echo "+ens1f1" > /sys/class/net/t_bond0/bonding/slaves"
$ ip link set ens1f0 down"
$ echo "+ens1f0" > /sys/class/net/t_bond0/bonding/slaves"
$ ethtool -i t_bond0"
$ ip link set ens1f1 up"
$ ip link set ens1f0 up"
$ ip link set t_bond0 up"
$ ip addr add 192.168.9.1/24 dev t_bond0"
$ ip addr add 2002::1/64 dev t_bond0"
This bond comes up okay, but things look slightly suspect in
/proc/net/bonding/t_bond0 output:
$ grep -i mii /proc/net/bonding/t_bond0
MII Status: up
MII Polling Interval (ms): 0
MII Status: up
MII Status: up
Now, pull a cable on one of the ports in the bond, then reconnect it, and
you'll see:
Slave Interface: ens1f0
MII Status: down
Speed: 1000 Mbps
Duplex: full
I believe this became a major issue as of commit 4d2c0cda0744, which for
802.3ad bonds, sets slave->link = BOND_LINK_DOWN, with a comment about
relying on link monitoring via miimon to set it correctly, but since the
miimon work queue never runs, the link just stays marked down.
If we simply tweak bond_option_mode_set() slightly, we can check for the
non-arp modes having no miimon value set, and insert BOND_DEFAULT_MIIMON,
which gets things back in full working order. This problem exists as far
back as 4.14, and might be worth fixing in all stable trees since, though
the work-around is to simply specify an miimon value yourself.
Reported-by: Bob Ball <ball@umich.edu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-18
The following series provides fixes to mlx5 core and net device driver.
Please pull and let me know if there's any problem.
For -stable v4.7
net/mlx5e: Don't allow aRFS for encapsulated packets
net/mlx5e: Fix quota counting in aRFS expire flow
For -stable v4.15
net/mlx5e: Only allow offloading decap egress (egdev) flows
net/mlx5e: Refine ets validation function
net/mlx5: Adjust clock overflow work period
For -stable v4.17
net/mlx5: E-Switch, UBSAN fix undefined behavior in mlx5_eswitch_mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the SPDX identifiers to HNS3 PF driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct hclge_desc_cb and hclge_desc_cb are never used in
anywhere. This patch removes them.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The input parameter "dev" of hns3_irq_handle() is indeed
used as a tqp vector, it is misleadin.
The struct member "flag" is used to indicate ring type,
so rename it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BIT() and GENMASK() to convert the bit mask, modify
the inconsistent ones, and remove useless ones.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using hex for bit offsets is inconsistent with the rest
of the file. Change them to decimal.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes some comment spelling errors, removes
redundant comments, rewrites misleading comments, and
adds some necessary comments.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove extra space and brackets.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apply the standard minor cleanup by returning ret outside
the brackets.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove some redundant assignments, because they have
been set to zero when allocate hdev.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-20
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add sharing of BPF objects within one ASIC: this allows for reuse of
the same program on multiple ports of a device, and therefore gains
better code store utilization. On top of that, this now also enables
sharing of maps between programs attached to different ports of a
device, from Jakub.
2) Cleanup in libbpf and bpftool's Makefile to reduce unneeded feature
detections and unused variable exports, also from Jakub.
3) First batch of RCU annotation fixes in prog array handling, i.e.
there are several __rcu markers which are not correct as well as
some of the RCU handling, from Roman.
4) Two fixes in BPF sample files related to checking of the prog_cnt
upper limit from sample loader, from Dan.
5) Minor cleanup in sockmap to remove a set but not used variable,
from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were trivial overlapping changes, so reasonably
easy to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netlink policy structure can be constant like other
drivers.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the ethtool callbacks for querying sfp/eeprom module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds qed APIs for reading the PHY module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The calculation of "wqe_size" is not correct when the tx queue is busy in
hinic_xmit_frame().
When there are no free WQEs, the tx flow will unmap the skb buffer, then
ring the doobell for the pending packets. But the "wqe_size" which used
to calculate the doorbell address is not correct. The wqe size should be
cleared to 0, otherwise, it will cause a doorbell error.
This patch fixes the problem.
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Lots of fixes, here goes:
1) NULL deref in qtnfmac, from Gustavo A. R. Silva.
2) Kernel oops when fw download fails in rtlwifi, from Ping-Ke Shih.
3) Lost completion messages in AF_XDP, from Magnus Karlsson.
4) Correct bogus self-assignment in rhashtable, from Rishabh
Bhatnagar.
5) Fix regression in ipv6 route append handling, from David Ahern.
6) Fix masking in __set_phy_supported(), from Heiner Kallweit.
7) Missing module owner set in x_tables icmp, from Florian Westphal.
8) liquidio's timeouts are HZ dependent, fix from Nicholas Mc Guire.
9) Link setting fixes for sh_eth and ravb, from Vladimir Zapolskiy.
10) Fix NULL deref when using chains in act_csum, from Davide Caratti.
11) XDP_REDIRECT needs to check if the interface is up and whether the
MTU is sufficient. From Toshiaki Makita.
12) Net diag can do a double free when killing TCP_NEW_SYN_RECV
connections, from Lorenzo Colitti.
13) nf_defrag in ipv6 can unnecessarily hold onto dst entries for a
full minute, delaying device unregister. From Eric Dumazet.
14) Update MAC entries in the correct order in ixgbe, from Alexander
Duyck.
15) Don't leave partial mangles bpf program in jit_subprogs, from
Daniel Borkmann.
16) Fix pfmemalloc SKB state propagation, from Stefano Brivio.
17) Fix ACK handling in DCTCP congestion control, from Yuchung Cheng.
18) Use after free in tun XDP_TX, from Toshiaki Makita.
19) Stale ipv6 header pointer in ipv6 gre code, from Prashant Bhole.
20) Don't reuse remainder of RX page when XDP is set in mlx4, from
Saeed Mahameed.
21) Fix window probe handling of TCP rapair sockets, from Stefan
Baranoff.
22) Missing socket locking in smc_ioctl(), from Ursula Braun.
23) IPV6_ILA needs DST_CACHE, from Arnd Bergmann.
24) Spectre v1 fix in cxgb3, from Gustavo A. R. Silva.
25) Two spots in ipv6 do a rol32() on a hash value but ignore the
result. Fixes from Colin Ian King"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (176 commits)
tcp: identify cryptic messages as TCP seq # bugs
ptp: fix missing break in switch
hv_netvsc: Fix napi reschedule while receive completion is busy
MAINTAINERS: Drop inactive Vitaly Bordug's email
net: cavium: Add fine-granular dependencies on PCI
net: qca_spi: Fix log level if probe fails
net: qca_spi: Make sure the QCA7000 reset is triggered
net: qca_spi: Avoid packet drop during initial sync
ipv6: fix useless rol32 call on hash
ipv6: sr: fix useless rol32 call on hash
net: sched: Using NULL instead of plain integer
net: usb: asix: replace mii_nway_restart in resume path
net: cxgb3_main: fix potential Spectre v1
lib/rhashtable: consider param->min_size when setting initial table size
net/smc: reset recv timeout after clc handshake
net/smc: add error handling for get_user()
net/smc: optimize consumer cursor updates
net/nfc: Avoid stalls when nfc_alloc_send_skb() returned NULL.
ipv6: ila: select CONFIG_DST_CACHE
net: usb: rtl8150: demote allmulti message to dev_dbg()
...
|
|
We get egress rules through the egdev mechanism when the ingress device
is not supporting offload, with the expected use-case of tunnel decap
ingress rule set on shared tunnel device.
Make sure to offload egress/egdev rules only if decap action (tunnel key
unset) exists there and err otherwise.
Fixes: 717503b9cf57 ("net: sched: convert cls_flower->egress_dev users to tc_setup_cb_egdev infra")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix bad alignment of SQ buffer in fragmented QP allocation.
It should start directly after RQ buffer ends.
Take special care of the end case where the RQ buffer does not occupy
a whole page. RQ size is a power of two, so would be the case only for
small RQ sizes (RQ size < PAGE_SIZE).
Fix wrong assignments for sqb->size (mistakenly assigned RQ size),
and for npages value of RQ and SQ.
Fixes: 3a2f70331226 ("net/mlx5: Use order-0 allocations for all WQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The flow counters binding support commit introduced a code change where
none NULL 'rule_dest' is always passed to mlx5_add_flow_rules, this breaks
'DON'T_TRAP' rules insertion.
The fix uses the equivalent 'dest_num' value instead of dest pointer
at the failed check.
fixes: 3b3233fbf02e ('IB/mlx5: Add flow counters binding support')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
With debug kernel UBSAN detects the following issue, which might happen
when eswitch instance is not created, fix this by testing the eswitch
pointer before returning the eswitch mode, if not set return mode =
SRIOV_NONE.
[ 32.528951] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlx5/core/eswitch.c:2219:12
[ 32.528951] member access within null pointer of type 'struct mlx5_eswitch'
[ 32.528951] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc3-dirty #181
[ 32.528951] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.0-0-g63451fca13-prebuilt.qemu-project.org 04/01/2014
[ 32.528951] Call Trace:
[ 32.528951] dump_stack+0xc7/0x13b
[ 32.528951] ? show_regs_print_info+0x5/0x5
[ 32.528951] ? __pm_runtime_use_autosuspend+0x140/0x140
[ 32.528951] ubsan_epilogue+0x9/0x49
[ 32.528951] ubsan_type_mismatch_common+0x1f9/0x2c0
[ 32.528951] ? ucs2_as_utf8+0x310/0x310
[ 32.528951] ? device_initialize+0x229/0x2e0
[ 32.528951] __ubsan_handle_type_mismatch+0x9f/0xc9
[ 32.528951] ? __ubsan_handle_divrem_overflow+0x19b/0x19b
[ 32.578008] ? ib_device_get_by_index+0xf0/0xf0
[ 32.578008] mlx5_eswitch_mode+0x30/0x40
[ 32.578008] mlx5_ib_add+0x1e0/0x4a0
Fixes: 57cbd893c4c5 ("net/mlx5: E-Switch, Move representors definition to a global scope")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Driver is yet to support aRFS for encapsulated packets, return early
error in such case.
Fixes: 18c908e477dc ("net/mlx5e: Add accelerated RFS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Quota should follow the amount of rules which do expire, and not the
number of rules that were examined, fixed that.
Fixes: 18c908e477dc ("net/mlx5e: Add accelerated RFS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver converts HW timestamp to wall clock time it subtracts
the last saved cycle counter from the HW timestamp and converts the
difference to nanoseconds.
The conversion is done by multiplying the cycles difference with the
clock multiplier value as a first step and therefore the cycles
difference should be small enough so that the multiplication product
doesn't exceed 64bit.
The overflow handling routine is in charge of updating the last saved
cycle counter in driver and it is called periodically using kernel
delayed workqueue.
The delay period for this work is calculated using the max HW cycle
counter value (a 41 bit mask) as a base which doesn't take the 64bit
limit into account so the delay period may be incorrect and too
long to prevent a large difference between the HW counter and the last
saved counter in SW.
This change adjusts the work period for the HW clock overflow work by
taking the minimum between the previous value and the quotient of max
u64 value and the clock multiplier value.
Fixes: ef9814deafd0 ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Removed an error message received when configuring ETS total
bandwidth to be zero.
Our hardware doesn't support such configuration, so we shall
reject it in the driver. Nevertheless, we removed the error message
in order to eliminate error messages caused by old userspace tools
who try to pass such configuration.
Fixes: ff0891915cd7 ("net/mlx5e: Fix ETS BW check")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If out ring is full temporarily and receive completion cannot go out,
we may still need to reschedule napi if certain conditions are met.
Otherwise the napi poll might be stopped forever, and cause network
disconnect.
Fixes: 7426b1a51803 ("netvsc: optimize receive completions")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add dependencies on PCI where necessary.
Fixes: 7e2bc7fb65 ("net: cavium: Drop dependency of NET_VENDOR_CAVIUM on PCI")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In cases the probing fails the log level of the messages should
be an error.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the SPI thread is not running, a simple reset of sync
state won't fix the transmit timeout. We also need to wake up the kernel
thread.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: ed7d42e24eff ("net: qca_spi: fix transmit queue timeout handling")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As long as the synchronization with the QCA7000 isn't finished, we
cannot accept packets from the upper layers. So let the SPI thread
enable the TX queue after sync and avoid unwanted packet drop.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For slow processors using bit-banging MDIO, 20ms can be too short a
timeout when waiting for the transmit timestamp to become
available. Double it to 40ms.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the 6352 and newer switches, the PTP Ethertype defaults to
ETH_P_1588. Hence it was not explicitly set. The 6165 however defaults
to 0. So explicitly set the EtherType.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6165 family supports a more restricted version of hardware time
stamps. Only L2 PTP is supported. All ports have to use the same
EtherType, and transport spec configuration. PTP can only be
enabled/disabled globally, not per port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6165 only supports layer L2 PTP, where as the more modern devices
also support UDP and UDPv6, i.e. L4. Abstract the supported receive
filters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6165 family does not have per port PTP control registers. Also, it
places the timestamp data in different registers. Abstract the current
implementation of 6352 compatible PTP devices so that 6165 can be
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6165 family has its global clock in the PTP global
registers. It does not support any form of PTP events. Add a function
to read the clock, fill in an ops structure, and register it with the
two members of the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6165 family supports PTP, but its registers use a different
layout to the currently supported devices. Abstract accessing the PTP
registers into a set of ops, so making space for a second
implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current description did not include new devices. Fix that by proving the
correct generic description.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This makes it more readable that rule is being used to return an err.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When translating command opcodes to a string, SET_DRIVER_VERSION
command was missing.
Fixes: 42ca502e179d0 ('net/mlx5_core: Use a macro in mlx5_command_str()')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update mlx5 command list and error return function to handle XRQ
commands.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As newer firmware supports double push/pop in a single FTE, we add
core bits and extend vlan action logic for it.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
NET_DSA_BCM_SF2 does not need to depend on CONFIG_OF anymore since we have
stubs when that option is disabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both BCMGENET and SYSTEMPORT build just fine with CONFIG_OF=n, we do have a
dependency on HAS_IOMEM that was not being reflected for SYSTEMPORT so add
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver builds fine even with CONFIG_OF=n since we now have stubs that are
provided.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
