| Age | Commit message (Collapse) | Author |
|---|
|
The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.
Fixes: d97c9f4ab000 ("net: mvpp2: 1000baseX support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. remove fine-tune property and related setting to simplify
the timing adjustment flow.
2. set timing value according to the value from device tree,
and will not care whether PHY insert internal delay.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.
There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5 driver falsely advertises support of software timestamping.
Fix it by removing the false indication.
Fixes: ef9814deafd0 ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.
Fixes: bd5251dbf156 ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Previous patches tried to make RIF deletion more robust and avoid
use-after-free situations.
As another precaution, hold a reference on a RIF's netdev and release it
when the RIF is deleted.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the past we had multiple instances where RIFs were not properly
deleted.
One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.
Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.
To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Next patch is going to make RIF deletion more robust by removing
reliance on fragile mlxsw_sp_lower_get(). This is because a netdev is
not necessarily our upper anymore when its IP addresses are flushed.
The inet{,6}addr notification blocks are going to resolve 'struct
mlxsw_sp' using container_of(), but the functions they call still use
mlxsw_sp_lower_get().
As a preparation for the next patch, propagate 'struct mlxsw_sp' down to
the functions called from the notification blocks and remove reliance on
mlxsw_sp_lower_get().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b3529af6bb0d ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.
However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.
Therefore, remove the get()/put() API and use create()/destroy()
instead.
One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 993107fea5ee ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is no longer used. Remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.
The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).
Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1
After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.
In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).
In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:
bond0.10
|
bond0
|
+-------+
| |
swp1 swp2
Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, only VRF and macvlan uppers are supported on top of VLAN
device configured over a bridge, so make sure the driver forbids other
uppers.
Note that enslavement to a VRF is handled earlier in the notification
block, so there is no need to check for a VRF upper here.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.
Fixes: e44758b78ae8 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.
Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.
Use secpath_set in places that immediately assign the return value to
skb.
This allows to remove skb->sp without touching these spots again.
secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... so this won't have to be changed when skb->sp goes away.
v2: no changes, preserve ack.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Will avoid touching this when sp pointer is removed from sk_buff struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_sec_path and secpath_exists helpers where possible.
This reduces noise in followup patch that removes skb->sp pointer.
v2: no changes, preseve acks from v1.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Turn on Broadcast writes
- UNH 1.8.1 clear bias for UNH 1000BT distortion
- UNH 1.8.7 optimize pre-emphasis for 100BasTx UNH 100W fix
- Enable Token-ring during 'Coma Mode'
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.20
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd52 ("vxge: serialize access to steering control register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe11733356 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5-uplink-rep-2018-12-15
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea80 ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08b6 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
variable 'cmd_op' set but not used [-Wunused-but-set-variable]
'op' never used since introduction in commit 7cb03b2347d5 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204bcf20 ("qlcnic: Fix operation
type and command type.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function should return an error if create_singlethread_workqueue()
fails.
Fixes: 34877a15f787 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a21598a ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c8a ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two statements that are indented too much by one space each,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.
Fixes: 01b3fd5ac97c ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
