| Age | Commit message (Collapse) | Author |
|---|
|
Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_tx beacon utility routines in mt76x02_mmio.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_beacon mac routines in mt76x02_mac.c in
order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add missing firmware declaration for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Make previously exported functions static where possible
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add mac workqueue support to mt76x2u driver in order
to compute device statistics and add mac stuck routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_debugfs in mt76x02-lib module in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Move mt76x02_update_channel routine in mt76x02-lib module in
order to be reused by mt76x0 driver adding get_survey support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Improve initvals_phy.h code readability (there are no actual changes
of original values)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Unify firmware version used on mt76x2e and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Print a debug message for every async FW event forwarded to mlx5
interfaces (mlx5e netdev and mlx5_ib rdma module).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow forwarding of SRQ events to mlx5_core interfaces, e.g. mlx5_ib.
Use mlx5_notifier_register/unregister in srq.c in order to allow seamless
transition of srq.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow forwarding QP and WQ events to mlx5_core interfaces, e.g. mlx5_ib
Use mlx5_notifier_register/unregister in qp.c in order to allow seamless
transition of qp.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before the new mlx5 event notification infrastructure and API,
mlx5_core used to process all events before forwarding them to mlx5
interfaces (mlx5e/mlx5_ib) and used to translate the event type enum
to a software defined enum, this is not needed anymore since it is ok
for mlx5e and mlx5_ib to receive FW events as is, at least the few ones
mlx5 core allows.
mlx5e and mlx5_ib already moved to use the new API and they only handle FW
events types, it is now safe to remove all equivalent software defined
events and the logic around them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
FW general event is used by mlx5_ib for RQ delay drop timeout event
handling, in this patch we allow to forward FW general event type to mlx5
notifiers chain so mlx5_ib can handle it and to deprecate the software
version of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The mlx5_interface->event callback is not used by mlx5e/mlx5_ib anymore.
We totally remove the delayed events logic work around, since with
the dynamic notifier registration API it is not needed anymore, mlx5_ib
can register its notifier and start receiving events exactly at the moment
it is ready to handle them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This to allow seamless migration to the new notifier chain API, and to
eventually deprecate interfaces dev->event callback.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Remove the deprecated mlx5_interface->event mlx5e callback and use new
mlx5 notifier API to subscribe for mlx5 events, handle port change event
as received from FW rather than handling the mlx5 core processed port
change software version event.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The idea is to allow mlx5 core interfaces (mlx5e/mlx5_ib) to be able to
receive some allowed FW events as is via the new notifier API.
In this patch we allow forwarding port change event to mlx5 core interfaces
(mlx5e/mlx5_ib) as it was received from FW.
Once mlx5e and mlx5_ib start using this event we can safely remove the
redundant software version of it and its translation logic.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use atomic notifier chain to fire events to mlx5 core driver
consumers (mlx5e/mlx5_ib) and provide mlx5 register/unregister notifier
API.
This API will replace the current mlx5_interface->event callback and all
the logic around it, especially the delayed events logic introduced by
commit 97834eba7c19 ("net/mlx5: Delay events till ib registration ends")
Which is not needed anymore with this new API where the mlx5 interface
can dynamically register/unregister its notifier.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd0f ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
allocation failure.
skb_linearization can fail due to memory allocation failure.
In such a case, the driver will drop the packet. In such a case
The driver used to print an error message.
This patch replaces this error message by a dedicated statistic.
Signed-off-by: Michael Shteinbok <michael.shteinbok@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add comments in the switch statement for XDP action to indicate
fallthrough is intended.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 26a4676faa1a ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To improve performance, this increases Rx descriptor to 256, Tx descriptor
to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the wol state forces to be initialized after reset, the state should
be preserved in suspend/resume sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee27f ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.
In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
classic uboot booting, the devicetree data is always there, so using it
makes sure we ask for the same nvram file independent of how we booted.
This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.
Fixes: bd1e82bb420a ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
