summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2010-01-23ixgbe: Allow the VF driver to be loaded before the PF driverGreg Rose
The PF Reset Done bit should not be set in the extended control register until the PF has actually completed the bring up process. It is a mis- interpretation of the purpose of this bit to assume it should be set when the physical reset of the device is done. Instead it should be used to indicate to the VFs when the PF is ready to provide them with required services. This is not until after the PF is finished coming up and ready to process mailbox events. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23ixgbe: Remove unused emulation MAC storage from the per VF data structure.Greg Rose
This data storage for SW emulated MAC addresses is unlikely to ever be used so pull it. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23ixgbe: Set the correct pool when VLANs are added in SR-IOV mode.Greg Rose
When VFs are allocated (as indicated by adapter->num_vfs is non-zero) then the PF pool is no longer zero. Instead it will be the same as the number of VFs allocated. When setting the VLVF entry for the PF we need to use the correct pool otherwise the PF will get VLAN packets from the wire because the packet will pass VFTA filtering and the PF has the default pool, but it will not get VLAN packets from the VFs because it has not set the correct pool bit in the VLVF entry. Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23e1000/e1000e: don't use small hardware rx buffersJesse Brandeburg
When testing the "e1000: enhance frame fragment detection" (and e1000e) patches we found some bugs with reducing the MTU size. The 1024 byte descriptor used with the 1000 mtu test also (re) introduced the (originally) reported bug, and causes us to need the e1000_clean_tx_irq "enhance frame fragment detection" fix. So what has occured here is that 2.6.32 is only vulnerable for mtu < 1500 due to the jumbo specific routines in both e1000 and e1000e. So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but is not vulnerable to the original issue reported. It has been pointed out that this vulnerability needs to be patched in older kernels that don't have the e1000 jumbo routine. Without the jumbo routines, we need the "enhance frame fragment detection" fix the e1000, old e1000e is only vulnerable for < 1500 mtu, and needs a similar fix. We split the patches up to provide easy backport paths. There is only a slight bit of extra code when this fix and the original "enhance frame fragment detection" fixes are applied, so please apply both, even though it is a bit of overkill. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23fmvj18x_cs: add new id (Panasonic lan & modem card)Ken Kawasaki
fmvj18x_cs, serial_cs: add new id Panasonic lan & modem card (model name:AL-VML101) Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23be2net: swap only first 2 fields of mcc_wrbSathya Perla
Only the first two fields of mcc wrb - embedded, payload_len need to be cpu_to_le32() swapped while issuing a cmd to the hw. The fields tag0, tag1 are opaque and returned back to cpu as is... Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23Please add support for Microsoft MN-120 PCMCIA network cardRon Murray
Please add support for Microsoft MN-120 PCMCIA network card. It's an old card, I know, but adding support is very easy. You just need to get tulip_core.c to recognise its vendor/device ID. Patch for kernel 2.6.32.4 (and many previous) attached. .....Ron Murray Signed-off-by: Ron Murray <rjmx@rjmx.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23Merge branch 'linux-2.6.33.y' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
2010-01-23Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
2010-01-22Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller
2010-01-22p54pci: revise tx lockingChristian Lamparter
This patch continues the effort which began with: "[PATCH] p54pci: move tx cleanup into tasklet". Thanks to these changes, p54pci's interrupt & tx cleanup routines can be made lock-less. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22b43: N-PHY: add TX toneRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22b43: N-PHY: add setting power amplifier filtersRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22b43: N-PHY: add running samplesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22b43: N-PHY: implement overriding RF controlRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22b43: check band widthRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22ath9k: Fix wifi disconnection when collocated bt scan is activeVasanthakumar Thiagarajan
As all bt packets are priority traffic during bt scan, wifi will get disconnected when bt scan lasts for few seconds. Fix this by allocating 10% of bt period time (4.5ms) to wifi fully. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22ath5k: fix setup for CAB queueBob Copeland
The beacon sent gating doesn't seem to work with any combination of flags. Thus, buffered frames tend to stay buffered forever, using up tx descriptors. Instead, use the DBA gating and hold transmission of the buffered frames until 80% of the beacon interval has elapsed using the ready time. This fixes the following error in AP mode: ath5k phy0: no further txbuf available, dropping packet Add a comment to acknowledge that this isn't the best solution. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22ath5k: dont use external sleep clock in AP modeBob Copeland
When using the external sleep clock in AP mode, the TSF increments too quickly, causing beacon interval to be much lower than it is supposed to be, resulting in lots of beacon-not-ready interrupts. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14802. Signed-off-by: Bob Copeland <me@bobcopeland.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22cfg80211: export multiple MAC addresses in sysfsJohannes Berg
If a device has multiple MAC addresses, userspace will need to know about that. Similarly, if it allows the MAC addresses to vary by a bitmask. If a driver exports multiple addresses, it is assumed that it will be able to deal with that many different addresses, which need not necessarily match the ones programmed into the device; if a mask is set then the device should deal addresses within that mask based on an arbitrary "base address". To test it all and show how it is used, add support to hwsim even though it can't actually deal with addresses different from the default. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-22mac80211: pass vif and station to update_tkip_keyJohannes Berg
When a TKIP key is updated, we should pass the station pointer instead of just the address, since drivers can use that to store their own data. We also need to pass the virtual interface pointer. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-21be2net: fix bug in rx page postingSathya Perla
Pages are posted to the rxq in such a way that more than one frag can share the page. The last frag that uses the page unmaps the page. In the case when a page is not fully used (due to lack of space in rxq) the last frag that uses the page is not being set as a "last_page_user"; instead, the next frag in the rxq is incorrectly being set. The fix has also been tested on ppc64 with 64k pages... Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21be2net: Add link test to list of ethtool self tests.Sarveshwar Bandi
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21be2net: ethtool self test reorganization.Sarveshwar Bandi
The ddr dma ethtool self test needs to be performed even when ETH_TEST_FL_OFFLINE is not set. Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21wimax/i2400m: Add support for more i6x50 SKUsInaky Perez-Gonzalez
The Intel WiMax Wireless Link 6050 can show under more than one USB ID. Add support for all, introducing a generic flag (i2400mu->i6050) that denotes a 6x50 based device. Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
2010-01-21phy: add RTBI mode for m88e1111Liu Yu-B13201
Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-21ucc_geth: update the tbi-phy settingLiu Yu-B13201
Old method only set tbi-phy for eth0. Signed-off-by: Liu Yu <yu.liu@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Add 57765 phy ID and enable devices.Matt Carlson
This patch rounds out the 57765 asic rev support by adding the 57765 phy ID and entering the 57765 device IDs in the pci table. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Bypass power source switching for 57765Matt Carlson
The 57765 repurposes all the GPIOs normally used to switch power sources when configured as a NIC device. This patch changes the code to avoid touching the GPIOs for this asic rev. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Turn off the debug UART for 57765Matt Carlson
If the debug UART is left enabled, the LEDs will not work properly. This patch disables the debug UART. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Fix tx mailbox initializationMatt Carlson
If a device supports MSI-X interrupts, the driver assumes TSS will be available. This is not true for the 57765. This patch changes the code so that only the default tx mailbox is initialized if TSS is not available. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Supply a nicaddr for 57765 jumbo RCBMatt Carlson
The 57765 needs the driver to supply a nic address to the jumbo RCB, just like all other devices except the 5717. This patch changes the test to single out the 5717 rather than maintain a lengthy whitelist of asic revs. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Fix 5717 and 57765 memory selftestsMatt Carlson
Both the 5717 and the 57765 will fail 'ethtool -t' selftests at the memory selftest portion. The memory map for these two devices differs from the rest of the asic revs and each other. This patch adds a new memory map to use for memory selftests. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Abort phy init for 5717 serdes devicesMatt Carlson
The 5717 serdes devices have a different phy register layout than all other previous serdes devices. This patch aborts the phy init sequence in tg3_phy_reset() if the device is a 5717 serdes. It also aborts the tg3_phy_toggle_apd() operation. Most other operations in the MII_SERDES path are O.K. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Add 5717 serdes phy IDMatt Carlson
The serdes and copper phys of the 5717 asic rev have different phy IDs. This patch adds the serdes phy ID. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Improve internal resource allocationsMatt Carlson
The 5717 and the 57765 have more resources at their disposal internally. This patch tunes the driver to get better performance. The adjustments made here only apply to the 57765 and 5717 asic revs. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20tg3: Enable PLL PD when CLKREQ disabled for 5717A0Matt Carlson
PCIe PLL power down cannot be used if CLKREQ is enabled because data corruption will occur. If CLKREQ is disabled though, enabling PCIE P1 PLL power-down saves some power. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20e1000e: enhance frame fragment detectionJesse Brandeburg
Originally patched by Neil Horman <nhorman@tuxdriver.com> e1000e could with a jumbo frame enabled interface, and packet split disabled, receive a packet that would overflow a single rx buffer. While in practice very hard to craft a packet that could abuse this, it is possible. this is related to CVE-2009-4538 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20e1000: enhance frame fragment detectionJesse Brandeburg
Originally From: Neil Horman <nhorman@tuxdriver.com> Modified by: Jesse Brandeburg <jesse.brandeburg@intel.com> Hey all- A security discussion was recently given: http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html And a patch that I submitted awhile back was brought up. Apparently some of their testing revealed that they were able to force a buffer fragment in e1000 in which the trailing fragment was greater than 4 bytes. As a result the fragment check I introduced failed to detect the fragement and a partial invalid frame was passed up into the network stack. I've written this patch to correct it. I'm in the process of testing it now, but it makes good logical sense to me. Effectively it maintains a per-adapter state variable which detects a non-EOP frame, and discards it and subsequent non-EOP frames leading up to _and_ _including_ the next positive-EOP frame (as it is by definition the last fragment). This should prevent any and all partial frames from entering the network stack from e1000. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-20e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()Roel Kluin
The variable count and i are unsigned so the (<|>=)0 tests do not work. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-19ath9k: fix beacon slot/buffer leakFelix Fietkau
When cleaning up beacon buffers and slots, ath9k currently checks if sc->ah->opmode is set to a beacon related mode before cleaning up buffers. An unfortunate ordering of interface up/down commands can lead to sc->ah->opmode being set to monitor mode, while there are AP interfaces present on the same wiphy. Always cleaning up beacon buffers if present fixes this issue. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19libertas/assoc.c: rearrange some strange line breaksJohn W. Linville
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19ath9k: make tx power config changes take effect immediatleyLuis R. Rodriguez
Users wishing to tweak tx power want it to happen immediately, try to respect that. This was tested by Lorenzo by measuring the received signal strength from an AP with ath9k and the patch. Changing the tx power on the AP produced these results: 1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm 2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm 3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm 4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm 5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm The result with 0 is an anomoly and would need to be addressed through a separate patch. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19libertas: Set/clear WPA keys before the WEP onesSamuel Ortiz
With the v10 firmware running on 8688 HW, clearing WPA keys after setting the WEP key prevents us from being able to associate with WEP APs. Swapping the calling order for assoc_helper_wpa_keys() and assoc_helper_wep_keys fixes that issue. Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19b43: N-PHY: silence warnings, add missing callRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19b43: N-PHY: implement and add multi-dimensional table readingRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19b43: N-PHY: implement and add reading one element tablesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19b43: N-PHY: implement and add multi-dimensional table writingRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19b43: N-PHY: add writing one element tablesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19p54pci: move tx cleanup into taskletChristian Lamparter
This patch moves the tx cleanup routines out of the critical interrupt context and into the (previously known as rx) tasklet. The main goal of this operation is to remove the extensive usage of spin_lock_irqsaves in the generic p54common library. The next step would be to modify p54usb to do the rx processing inside a tasklet (just like usbnet). Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit (git 2.34.1) at 2025-09-23 12:09:14 +0000