| Age | Commit message (Collapse) | Author |
|---|
|
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad407c ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.
Fixes: 5da083d1922c ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since (40, 44) is invalid.
Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.
Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.
Fixes: af45a9003f1f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.
This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc4863 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Pull networking fixes from David Miller:
1) Handle notifier registry failures properly in tun/tap driver, from
Tonghao Zhang.
2) Fix bpf verifier handling of subtraction bounds and add a testcase
for this, from Edward Cree.
3) Increase reset timeout in ftgmac100 driver, from Ben Herrenschmidt.
4) Fix use after free in prd_retire_rx_blk_timer_exired() in AF_PACKET,
from Cong Wang.
5) Fix SElinux regression due to recent UDP optimizations, from Paolo
Abeni.
6) We accidently increment IPSTATS_MIB_FRAGFAILS in the ipv6 code
paths, fix from Stefano Brivio.
7) Fix some mem leaks in dccp, from Xin Long.
8) Adjust MDIO_BUS kconfig deps to avoid build errors, from Arnd
Bergmann.
9) Mac address length check and buffer size fixes from Cong Wang.
10) Don't leak sockets in ipv6 udp early demux, from Paolo Abeni.
11) Fix return value when copy_from_user() fails in
bpf_prog_get_info_by_fd(), from Daniel Borkmann.
12) Handle PHY_HALTED properly in phy library state machine, from
Florian Fainelli.
13) Fix OOPS in fib_sync_down_dev(), from Ido Schimmel.
14) Fix truesize calculation in virtio_net which led to performance
regressions, from Michael S Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
samples/bpf: fix bpf tunnel cleanup
udp6: fix jumbogram reception
ppp: Fix a scheduling-while-atomic bug in del_chan
Revert "net: bcmgenet: Remove init parameter from bcmgenet_mii_config"
virtio_net: fix truesize for mergeable buffers
mv643xx_eth: fix of_irq_to_resource() error check
MAINTAINERS: Add more files to the PHY LIBRARY section
ipv4: fib: Fix NULL pointer deref during fib_sync_down_dev()
net: phy: Correctly process PHY_HALTED in phy_stop_machine()
sunhme: fix up GREG_STAT and GREG_IMASK register offsets
bpf: fix bpf_prog_get_info_by_fd to dump correct xlated_prog_len
tcp: avoid bogus gcc-7 array-bounds warning
net: tc35815: fix spelling mistake: "Intterrupt" -> "Interrupt"
bpf: don't indicate success when copy_from_user fails
udp6: fix socket leak on early demux
net: thunderx: Fix BGX transmit stall due to underflow
Revert "vhost: cache used event for better performance"
team: use a larger struct for mac address
net: check dev->addr_len for dev_set_mac_address()
phy: bcm-ns-usb3: fix MDIO_BUS dependency
...
|
|
The PPTP set the pptp_sock_destruct as the sock's sk_destruct, it would
trigger this bug when __sk_free is invoked in atomic context, because of
the call path pptp_sock_destruct->del_chan->synchronize_rcu.
Now move the synchronize_rcu to pptp_release from del_chan. This is the
only one case which would free the sock and need the synchronize_rcu.
The following is the panic I met with kernel 3.3.8, but this issue should
exist in current kernel too according to the codes.
BUG: scheduling while atomic
__schedule_bug+0x5e/0x64
__schedule+0x55/0x580
? ppp_unregister_channel+0x1cd5/0x1de0 [ppp_generic]
? dev_hard_start_xmit+0x423/0x530
? sch_direct_xmit+0x73/0x170
__cond_resched+0x16/0x30
_cond_resched+0x22/0x30
wait_for_common+0x18/0x110
? call_rcu_bh+0x10/0x10
wait_for_completion+0x12/0x20
wait_rcu_gp+0x34/0x40
? wait_rcu_gp+0x40/0x40
synchronize_sched+0x1e/0x20
0xf8417298
0xf8417484
? sock_queue_rcv_skb+0x109/0x130
__sk_free+0x16/0x110
? udp_queue_rcv_skb+0x1f2/0x290
sk_free+0x16/0x20
__udp4_lib_rcv+0x3b8/0x650
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 28b45910ccda ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910ccda ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seth Forshee noticed a performance degradation with some workloads.
This turns out to be due to packet drops. Euan Kemp noticed that this
is because we drop all packets where length exceeds the truesize, but
for some packets we add in extra memory without updating the truesize.
This in turn was kept around unchanged from ab7db91705e95 ("virtio-net:
auto-tune mergeable rx buffer size for improved performance"). That
commit had an internal reason not to account for the extra space: not
enough bits to do it. No longer true so let's account for the allocated
length exactly.
Many thanks to Seth Forshee for the report and bisecting and Euan Kemp
for debugging the issue.
Fixes: 680557cf79f8 ("virtio_net: rework mergeable buffer handling")
Reported-by: Euan Kemp <euan.kemp@coreos.com>
Tested-by: Euan Kemp <euan.kemp@coreos.com>
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.
Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff76 ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs CONFIG_HAS_IOMEM and OF to be functional, but we still
let it build with COMPILE_TEST. This fixes the unmet dependency after
selecting MDIO_BCM_UNIMAC in commit mentioned below:
warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has
unmet direct dependencies (NETDEVICES && MDIO_DEVICE && HAS_IOMEM &&
OF_MDIO)
Fixes: 9a4e79697009 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.
Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f379cf ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the values to match those from the STP2002QFP documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current code, old and new PHY states are always logged.
>From now on, log only PHY state transitions.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Express the same logic more succinctly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefer logical operator that expresses the intent to bitwise one that
happens to give the same result.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcmgenet_mii_init() has an error path which is strictly identical to the
unwinding that bcmgenet_mii_exit() does, so have bcmgenet_mii_init()
utilize bcmgenet_mii_exit() for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have fully migrated to the mdio-bcm-unimac driver, drop the
legacy MDIO bus code which did duplicate a fair amount of code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for having the bcmgenet driver migrate over the
mdio-bcm-unimac driver, add a platform data structure which allows
passing integrating specific details like bus name, wait function to
complete MDIO operations and PHY mask.
We also define what the platform device name contract is by defining
UNIMAC_MDIO_DRV_NAME and moving it to the platform_data header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to be stricly identical to what bcmgenet does, add a debug
print when a PHY workaround during bus->reset() is executed. Preliminary
change to moving bcmgenet towards mdio-bcm-unimac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for having multiple GENET instances in a system (up to
3), make sure that we do include the bus instance number in the name of
the MDIO bus such that we change it from "unimac-mdio" to
"unimac-mdio-0" for instance.
So far, the only user of this driver is using Device Tree, which uses a
lookup/parenting based technique to map PHY devices to their respective
MDIO bus controllers, hence causing no additional changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor the code that does the busy polling on the MDIO_BUSY bit since we
will have different code-paths for for completion depending on whether
we are using interrupts or polling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We no longer place these on a list so they can be const.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preparing for the following fix of MDIO phy access:
Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.
lan9303_port_phy_reg_wait_for_completion() to
lan9303_indirect_phy_wait_for_completion()
lan9303_port_phy_reg_read() to
lan9303_indirect_phy_read()
lan9303_port_phy_reg_write() to
lan9303_indirect_phy_write()
Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.
Added some commments to the register definitions.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle that MDIO read with no response return 0xffff.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
Two fixes for for brcmfmac, the crash was reported by two people
already so it's a high priority fix.
brcmfmac
* fix a crash in skb headroom handling in v4.13-rc1
* fix a memory leak due to a merge error in v4.6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
