| Age | Commit message (Collapse) | Author |
|---|
|
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PHY IDs for the DP83825CS, DP83825CM and the DP83825S devices to the
DP83822 driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add phy IDs to the DP83822 phy driver for the DP83826N
and the DP83826NC devices. The register map and features
are the same for basic enablement.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5a5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable U2P3 may miss zero packet for bulk-in.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A malicious user could use RAW sockets and fool
GTP using them as standard SOCK_DGRAM UDP sockets.
BUG: KMSAN: uninit-value in udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline]
BUG: KMSAN: uninit-value in setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85
CPU: 0 PID: 11262 Comm: syz-executor613 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
udp_tunnel_encap_enable include/net/udp_tunnel.h:174 [inline]
setup_udp_tunnel_sock+0x45e/0x6f0 net/ipv4/udp_tunnel.c:85
gtp_encap_enable_socket+0x37f/0x5a0 drivers/net/gtp.c:827
gtp_encap_enable drivers/net/gtp.c:844 [inline]
gtp_newlink+0xfb/0x1e50 drivers/net/gtp.c:666
__rtnl_newlink net/core/rtnetlink.c:3305 [inline]
rtnl_newlink+0x2973/0x3920 net/core/rtnetlink.c:3363
rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424
netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:639 [inline]
sock_sendmsg net/socket.c:659 [inline]
____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330
___sys_sendmsg net/socket.c:2384 [inline]
__sys_sendmsg+0x451/0x5f0 net/socket.c:2417
__do_sys_sendmsg net/socket.c:2426 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2424
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441359
Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff1cd0ac28 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441359
RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000246 R12: 00000000004020d0
R13: 0000000000402160 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags+0x3c/0x90 mm/kmsan/kmsan.c:144
kmsan_internal_alloc_meta_for_pages mm/kmsan/kmsan_shadow.c:307 [inline]
kmsan_alloc_page+0x12a/0x310 mm/kmsan/kmsan_shadow.c:336
__alloc_pages_nodemask+0x57f2/0x5f60 mm/page_alloc.c:4800
alloc_pages_current+0x67d/0x990 mm/mempolicy.c:2207
alloc_pages include/linux/gfp.h:534 [inline]
alloc_slab_page+0x111/0x12f0 mm/slub.c:1511
allocate_slab mm/slub.c:1656 [inline]
new_slab+0x2bc/0x1130 mm/slub.c:1722
new_slab_objects mm/slub.c:2473 [inline]
___slab_alloc+0x1533/0x1f30 mm/slub.c:2624
__slab_alloc mm/slub.c:2664 [inline]
slab_alloc_node mm/slub.c:2738 [inline]
slab_alloc mm/slub.c:2783 [inline]
kmem_cache_alloc+0xb23/0xd70 mm/slub.c:2788
sk_prot_alloc+0xf2/0x620 net/core/sock.c:1597
sk_alloc+0xf0/0xbe0 net/core/sock.c:1657
inet_create+0x7c7/0x1370 net/ipv4/af_inet.c:321
__sock_create+0x8eb/0xf00 net/socket.c:1420
sock_create net/socket.c:1471 [inline]
__sys_socket+0x1a1/0x600 net/socket.c:1513
__do_sys_socket net/socket.c:1522 [inline]
__se_sys_socket+0x8d/0xb0 net/socket.c:1520
__x64_sys_socket+0x4a/0x70 net/socket.c:1520
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pablo Neira <pablo@netfilter.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-01-22
The following pull-request contains BPF updates for your *net-next* tree.
We've added 92 non-merge commits during the last 16 day(s) which contain
a total of 320 files changed, 7532 insertions(+), 1448 deletions(-).
The main changes are:
1) function by function verification and program extensions from Alexei.
2) massive cleanup of selftests/bpf from Toke and Andrii.
3) batched bpf map operations from Brian and Yonghong.
4) tcp congestion control in bpf from Martin.
5) bulking for non-map xdp_redirect form Toke.
6) bpf_send_signal_thread helper from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend stats group array of uplink representor with all stats that are
available for PF in legacy mode, besides ipsec and TLS which are not
supported.
Don't output vport stats for uplink representor because they are already
handled by 802_3 group (with different names: {tx|rx}_{bytes|packets}_phy).
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Q counters were disabled for all types of representors to prevent an issue
where there is not enough resources to init q counters for 127 representor
instances. Enable q counters only for uplink representors to support
"rx_out_of_buffer", "rx_if_down_packets" counters in ethtool.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to support all of the supported stats that are available in legacy
mode for switchdev uplink representors, convert rep stats infrastructure to
reuse struct mlx5e_stats_grp that is already used when device is in legacy
mode. Refactor rep code to use array of mlx5e_stats_grp
structures (constructed using macros provided by stats infra) to
fill/update stats, instead of fixed hardcoded set of values. This approach
allows to easily extend representors with new stats types.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Don't copy all of the stats groups used for mlx5e ethernet NIC profile,
have a separate stats groups for IPoIB with the set of the needed stats
only.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Convert stats groups array to array of "stats group" pointers to allow
sharing and individual selection of groups per profile as illustrated in
the next patches.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Introduce new macros to declare stats callbacks and groups, for better
code reuse and for individual groups selection per profile which will be
introduced in next patches.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Attach stats groups array to the profiles and make the stats utility
functions (get_num, update, fill, fill_strings) generic and use the
profile->stats_grps rather the hardcoded NIC stats groups.
This will allow future extension to have per profile stats groups.
In this patch mlx5e NIC and IPoIB will still share the same stats
groups.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Clean up the code and allows to call uplink rep init/cleanup
from different location later.
To be used later for a new uplink representor mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow connecting SW steering source table to a lower/same level
destination table.
Lifting this limitation is required to support Connection Tracking.
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Modify header supports ADD/SET and from this patch
also COPY. Copy allows to copy header fields and
metadata.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Modify set actions are not supported on both tx
and rx, added a check for that.
Also refactored the code in a way that every modify
action has his own functions, this needed so in the
future we could add copy action more smoothly.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the flowtables offload all the devices in the flowtables
share the same flow_block. An offload rule will be installed on
all the devices. This scenario is not correct.
It is no problem if there are only two devices in the flowtable,
The rule with ingress and egress on the same device can be reject
by driver.
But more than two devices in the flowtable will install the wrong
rules on hardware.
For example:
Three devices in a offload flowtables: dev_a, dev_b, dev_c
A rule ingress from dev_a and egress to dev_b:
The rule will install on device dev_a.
The rule will try to install on dev_b but failed for ingress
and egress on the same device.
The rule will install on dev_c. This is not correct.
The flowtables offload avoid this case through restricting the ingress dev
with FLOW_DISSECTOR_KEY_META.
So the mlx5e driver also should support the FLOW_DISSECTOR_KEY_META parse.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_chains.c:35:20: warning: symbol 'ESW_POOLS' was not declared. Should it be static?
Fixes: 39ac237ce009 ("net/mlx5: E-Switch, Refactor chains and priorities")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Acked-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
since mlx5 hardware can segment correctly TSO packets on VXLAN over VLAN
topologies, CPU usage can improve significantly if we enable tunnel
offloads in dev->vlan_features, like it was done in the past with other
NIC drivers (e.g. mlx4, be2net and ixgbe).
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use "%zu" for size_t. Seen on ARM allmodconfig:
drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
Fixes: 130c7b46c93d ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The first batch of driver conversions missed a few cases where we can
use phy_do_ioctl too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
